OPA657UB - 1.6GHz Low-Noise FET Op Amp | Texas Instruments
部品番号: OPA657UB ✓ 生産中OPA657UB 概要
An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. The FET-input architecture places a low-voltage-noise JFET input stage ahead of the high-gain, voltage-feedback amplifier. This combination makes the OPA657UB useful where a low-noise input stage, wide signal bandwidth, and high dynamic range must coexist in a compact analog circuit.
The principal performance features of the OPA657UB include its 1.6 GHz gain-bandwidth product, FET input stage, and 700 V/µs slew rate. Its decompensated architecture is particularly relevant to precision ADC driving and wideband transimpedance amplifiers because it supports high-speed operation without requiring a conventional unity-gain stability trade-off. The device is offered in an 8-pin SOIC package for surface-mount assembly.
The OPA657 combines a high-gain-bandwidth voltage-feedback core with a low-voltage-noise JFET input stage. This arrangement supports instrumentation applications in which input-referred noise can limit the usable dynamic range even when the selected ADC or detector has adequate resolution. The decompensated design also allows the amplifier to retain useful bandwidth in applications that normally require higher closed-loop gain.
Typical uses include photodiode and optical-sensor signal chains, precision ADC input amplifiers, high-impedance instrumentation, wideband active filters, and communications or test equipment. In a transimpedance stage, the FET inputs help reduce current-related noise while the 1.6 GHz bandwidth supports fast detector signals. In an ADC driver, the wide bandwidth and 700 V/µs slew rate help preserve large-signal fidelity when driving the converter input.
PCB design should prioritize short feedback paths, low-leakage-area layouts, and clean return-current routing around the high-impedance input stage. Decoupling capacitors should be placed close to the supply pins, while sensitive input traces should remain physically separated from output and slew-rate-current paths. The complete pin assignments and recommended application circuits should be taken directly from the Texas Instruments datasheet.
This product page combines the OPA657UB manufacturer specifications, verified ordering information, package details, drop-in candidate evaluation, comparison criteria, and application-focused design guidance. It is intended to support engineering selection while clearly separating documented device characteristics from parameters that require additional design confirmation.
ドロップイン代替品: OPA657UB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: OPA657UB (同一形状・フットプリント) — 相違点: Amplifier Type, Input Stage, Package.
OPA657U
✅ ドロップイン価格はお問い合わせください
データシートを見る →OPA657UG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
OPA657UID
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
OPA657UB 最大定格&電気的特性
| Amplifier Type | Single voltage-feedback operational amplifier |
| Number of Channels | 1 channel |
| Input Stage | Low-voltage-noise FET/JFET input |
| Gain-Bandwidth Product | 1.6 GHz |
| Slew Rate | 700 V/µs |
| Supply Voltage Range | 10 V to 12 V |
| Architecture | Decompensated voltage-feedback amplifier |
| パッケージ | 8-pin SOIC |
| Package Code | D |
| 動作温度範囲 | -40°C to +85°C |
| 実装タイプ | Surface mount |
| Primary Application | High-precision ADC driving and wideband transimpedance amplification |
OPA657UB ピン構成
| ピン 1 | NC — Not connected (per datasheet) |
| ピン 2 | -IN — Inverting input |
| ピン 3 | +IN — Non-inverting input |
| ピン 4 | V- — Negative supply connection |
| ピン 5 | NC — Not connected (per datasheet) |
| ピン 6 | OUT — Amplifier output |
| ピン 7 | V+ — Positive supply connection |
| ピン 8 | NC — Not connected (per datasheet) |
主な用途
OPA657UB の用途: 6 件s: High-Speed Precision ADC Driver, Photodiode Transimpedance Amplifier, Wideband Active Filter, High-Impedance Instrumentation Amplifier, Communications Signal Conditioning, Optical Sensor Readout.
High-Speed Precision ADC Driver
The OPA657UB fits high-speed ADC input stages because its 1.6 GHz gain-bandwidth product and 700 V/µs slew rate preserve large-signal movement when the converter input presents a difficult capacitive or resistive load. According to the Texas Instruments manufacturer datasheet, the low-voltage-noise FET/JFET input stage also supports high-dynamic-range acquisition rather than merely providing bandwidth. The amplifier is placed directly before the ADC input, with the feedback network kept short and the output routed away from sensitive input nodes. Verify the ADC's input range, settling requirements, kickback behavior, and operating gain against the amplifier's decompensated stability characteristics before production release.
おすすめ
Photodiode Transimpedance Amplifier
The OPA657UB is well suited to wideband photodiode amplification because the low-voltage-noise JFET input stage limits the amplifier's own input-noise contribution while the 1.6 GHz bandwidth supports rapidly varying detector signals. In a transimpedance topology, the OPA657UB converts photocurrent into a proportional output voltage, with feedback resistance and compensation capacitance setting the usable response. According to the Texas Instruments manufacturer datasheet, the decompensated architecture is intended for this use. Keep the summing node physically small, use low-leakage construction around the input, and verify the combined photodiode capacitance, feedback capacitance, and target gain against the amplifier stability requirements.
おすすめ
Wideband Active Filter
The OPA657UB can implement wideband active filtering where the required closed-loop bandwidth approaches the limits imposed by conventional voltage-feedback amplifiers. Its 1.6 GHz gain-bandwidth product and 700 V/µs slew rate provide the transition bandwidth and large-signal response needed in high-order filters, while the FET input stage helps preserve low-noise operation. According to the Texas Instruments manufacturer datasheet, the device is a decompensated voltage-feedback amplifier and therefore requires stability analysis at the selected noise gain. Component tolerances, parasitic capacitance, output loading, and the filter's actual gain should be included in simulation before fabrication.
おすすめ
High-Impedance Instrumentation Amplifier
The OPA657UB suits precision instrumentation stages in which source impedance is high and the amplifier must contribute little input current or noise. According to the Texas Instruments manufacturer datasheet, the low-voltage-noise JFET input stage supports very high dynamic range, while the 1.6 GHz gain-bandwidth product provides more bandwidth than many general-purpose precision amplifiers. The device can amplify sensor or laboratory signals before digitization, particularly when source capacitance is modest and rise time must be preserved. Use guarding, clean connectors, and controlled board contamination to prevent leakage and surface leakage from overwhelming the signal, and confirm bias-current behavior at the highest operating temperature.
おすすめ
Communications Signal Conditioning
The OPA657UB can condition high-rate communications signals when the receiver chain requires low input noise, rapid slew, and accurate large-signal reproduction. Its 1.6 GHz gain-bandwidth product and 700 V/µs slew rate support wideband gain blocks, while the FET input stage helps avoid adding excessive input-referred noise to the receiver. According to the Texas Instruments manufacturer datasheet, the amplifier is designed for high dynamic range. Place input and feedback paths away from clocks, Ethernet interfaces, switching supplies, and other high-slew-current nodes. Confirm the required gain, output loading, channel-isolation behavior, and frequency-dependent distortion against the complete communications link budget.
おすすめ
Optical Sensor Readout
The OPA657UB is applicable to optical sensor readouts where a weak detector signal must be amplified without introducing excessive broadband noise. The low-voltage-noise FET/JFET input stage and 1.6 GHz bandwidth provide a useful combination for photodiode, optical receiver, and laboratory detector front ends. According to the Texas Instruments manufacturer datasheet, the amplifier is intended for wideband transimpedance applications, making it suitable when detector output must be captured rapidly. Keep the input node compact and isolate it from humid surfaces, contamination, and switching nodes. Calculate the transimpedance gain from the required detector current and output swing, then validate the complete stability and noise response with the actual sensor capacitance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA657UB — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | OPA657U | OPA657UG4 | OPA657UID |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | Voltage-feedback operational amplifier | Voltage-feedback operational amplifier | Voltage-feedback operational amplifier | Voltage-feedback operational amplifier |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| Input Stage | Low-voltage-noise FET/JFET input | Low-voltage-noise FET/JFET input | Low-voltage-noise FET/JFET input | Low-voltage-noise FET/JFET input |
| Gain-Bandwidth Product | 1.6 GHz | 1.6 GHz | 1.6 GHz | 1.6 GHz |
| Slew Rate | 700 V/µs | 700 V/µs | 700 V/µs | 700 V/µs |
| Supply Voltage Range | 10 V to 12 V | 10 V to 12 V | 10 V to 12 V | 10 V to 12 V |
| Primary Application | High-precision ADC driving and wideband transimpedance amplification | High-precision ADC driving and wideband transimpedance amplification | High-precision ADC driving and wideband transimpedance amplification | High-precision ADC driving and wideband transimpedance amplification |
主な差別化要因
- Combines 1.6 GHz bandwidth with a low-noise FET input stage (vs OPA657U)
- Pin-compatible same-family option (vs OPA657UG4)
- Direct 8-pin SOIC upgrade path (vs OPA657UID)
設計ノート
Place the input, feedback, and output-loop components close to the OPA657UB. Keep the inverting-input summing node compact, especially in transimpedance circuits, because parasitic capacitance and board leakage can alter stability and input bias behavior. Route high-speed output current away from the non-inverting input, use a continuous ground reference, and avoid placing test pads or long unprotected input traces adjacent to the sensitive input.
Use the supply range identified for the OPA657UB and place local high-frequency decoupling directly across the V+ and V- pins. The amplifier's 700 V/µs slew rate can produce fast output transitions, making supply-return coupling possible even though the input stage is low noise. Verify positive and negative supply sequencing, output swing, and load current against the manufacturer operating limits before connecting it to a sensitive converter or detector.
Do not assume conventional unity-gain stability because the OPA657UB uses a decompensated architecture. Confirm the minimum stable gain, allowable noise gain, source and load capacitance, and feedback-network impedance using the manufacturer stability and application information. A board that works at one supply voltage may not retain adequate phase margin across temperature, load, and component tolerance, so validate the worst-case network rather than only the nominal simulation.
Control leakage around the FET/JFET input stage by using clean PCB materials, conformal protection where environmental exposure is expected, and guard structures driven only as permitted by the circuit design. Avoid flux residue, fingerprints, moisture, and long exposed copper near the input. In optical and photodiode applications, place the amplifier close to the detector to minimize parasitic capacitance and leakage before the signal enters the summing node.
コンプライアンス情報
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code. The OPA657UB is an industrial-temperature amplifier ordering option rather than an explicitly identified automotive-qualified variant.