OPA704PA - 3MHz Low-Power Rail-to-Rail Op Amp | Texas Instruments
部品番号: OPA704PA ✓ 生産中OPA704PA 概要
An operational amplifier is a voltage-feedback amplifier that uses negative feedback to amplify the voltage difference between its inverting and non-inverting inputs. In the broader electronics hierarchy, an op amp belongs to the amplifier IC and analog signal-processing categories, where its gain, bandwidth, input impedance, common-mode range, and output-drive capability determine how faithfully a small signal is amplified. The OPA704PA is specifically positioned for circuits that require low input bias current and rail-to-rail signal handling.
The principal features of the OPA704PA include 1 pA input bias current, a maximum offset voltage of 750 µV, 3 MHz gain-bandwidth, 3 V/µs slew rate, and rail-to-rail input and output operation. The very low bias current is valuable when the source impedance is high or when leakage from sensors, photodiodes, capacitors, or chemical-sensing elements would otherwise disturb the measurement. Rail-to-rail behavior allows the output to approach the supply limits more closely than a conventional non-rail-to-rail output stage.
At a 3 MHz unity-gain bandwidth, the OPA704PA provides useful bandwidth for low-frequency precision signals, signal conditioning, active filtering, and general-purpose analog gain stages. Its 3 V/µs slew rate determines how quickly the output can follow a changing input waveform. These characteristics make it suitable for instrumentation where accuracy and low input current matter more than the very high bandwidth associated with modern high-speed amplifiers.
Typical OPA704PA applications include precision sensor amplifiers, photodiode signal chains, low-current measurement circuits, data-acquisition front ends, active filters, and low-power analog signal-conditioning modules. Its single 12 V supply also simplifies designs that cannot use split rails. In battery-operated or portable equipment, the low-power operating characteristics help reduce system energy consumption while preserving useful closed-loop bandwidth.
The primary design consideration is to verify input and output voltage limits across temperature, load current, and supply tolerance before closing the feedback loop. Input and output stability must also be checked with the intended source impedance, capacitor values, and PCB layout. Because input bias current is exceptionally low, guarding and leakage control remain important around sensitive high-impedance nodes.
This product page combines manufacturer specifications, package and sourcing information, practical application guidance, and a verified drop-in replacement assessment. It helps engineers evaluate the OPA704PA alongside alternative amplifier choices while preserving the distinction between exact replacement qualification and broader functional similarity.
ドロップイン代替品: OPA704PA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストOPA704PA 最大定格&電気的特性
| Number of Channels | 1 channel |
| Product Type | Single operational amplifier |
| Nominal Supply Voltage | 12 V |
| Gain-Bandwidth Product | 3 MHz |
| Slew Rate | 3 V/µs |
| Input Bias Current | 1 pA |
| Maximum Input Offset Voltage | 750 µV |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Process Technology | CMOS |
| Package Type | 8-pin PDIP |
| 実装タイプ | Through-hole |
| RoHS ステータス | Compliant |
OPA704PA 8-pin pdip ピン配置ガイド
OPA704PA (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA704PA.
詳細は データシート をご参照ください。
主な用途
OPA704PA の用途: 6 件s: Precision Sensor Signal Conditioning, Photodiode Transimpedance Amplification, Low-Current Measurement Front End, Data-Acquisition Analog Channel, Active Filter and Equalization, Low-Power Analog Control Module.
Precision Sensor Signal Conditioning
The OPA704PA fits low-impedance-error signal conditioning around high-source-impedance sensors because its input bias current is specified at 1 pA. The amplifier can amplify a small sensor differential while its rail-to-rail input behavior supports operation near the limits of a single-supply signal range. Designers should verify the input common-mode range across supply tolerance and temperature, and they should use guarding or a protective low-leakage PCB surface when source impedances are high. The 3 MHz gain-bandwidth product supports moderate-bandwidth instrumentation stages rather than high-speed sensing.
Photodiode Transimpedance Amplification
The OPA704PA is suitable for a photodiode transimpedance front end because its 1 pA input bias current minimizes the DC error associated with the detector and feedback network. Its 3 MHz gain-bandwidth product and 3 V/µs slew rate provide useful response for moderate-speed optical measurements. The photodiode node must remain short and clean, and the feedback capacitor should be selected using the manufacturer stability guidance for the chosen transimpedance gain. Guarding is important when leakage from the board or connectors is comparable to the detector current.
Low-Current Measurement Front End
The OPA704PA can serve as the amplifier in a low-current measurement chain where sensor leakage and amplifier bias current would otherwise obscure the signal. Its 1 pA input bias current is the central benefit, while the maximum input offset voltage of 750 µV establishes the initial DC error that must be considered during calibration. Rail-to-rail output operation can help preserve measurement span in a single-supply design. Use clean connectors, guard structures, and low-leakage insulation, and verify offset drift, noise, and bias-current behavior over the full intended temperature range.
Data-Acquisition Analog Channel
OPA704PA-based analog channels can condition low-level inputs before an ADC in data-acquisition equipment. The amplifier’s 3 MHz gain-bandwidth product gives adequate loop bandwidth for many moderate-rate measurements, and its 3 V/µs slew rate limits large-signal distortion during channel transitions. Rail-to-rail input and output characteristics are useful when the converter’s input range must be approached closely. The design should include gain-error analysis, source-impedance limits, ADC drive settling, and any required isolation or anti-alias filtering ahead of the converter.
Active Filter and Equalization
The OPA704PA is appropriate for active filtering, equalization, and gain stages where low bias current and rail-to-rail operation are more important than very high bandwidth. Its 3 MHz gain-bandwidth product supports filters with moderate upper cutoffs, while the 750 µV maximum offset voltage must be included when the stage also performs DC amplification. Component tolerances and the amplifier’s finite gain and output-drive behavior can shift the realized response. Validate stability and corner accuracy using the manufacturer’s recommended passive values and the actual PCB layout.
Low-Power Analog Control Module
OPA704PA can be used in compact, single-supply analog control modules that combine sensing and conditioning without requiring a dual-rail amplifier. The CMOS device is identified as a low-power 12 V operational amplifier, while its 1 pA bias current supports high-impedance control nodes. Rail-to-rail operation increases usable output range, and the 3 MHz bandwidth provides adequate response for many slow control loops. Designers should verify output-current capability for the driven load, confirm shutdown behavior when applicable, and ensure the selected operating point remains inside the datasheet’s electrical limits.
エンジニアリング参考データ: OPA704PA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-pin PDIP |
| Brand | Texas Instruments |
| Number of Channels | 1 channel |
| Nominal Supply Voltage | 12 V |
| Gain-Bandwidth Product | 3 MHz |
| Slew Rate | 3 V/µs |
| Input Bias Current | 1 pA |
| Maximum Input Offset Voltage | 750 µV |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
主な差別化要因
- Exceptionally low input bias current for precision measurement (vs OPA704UA)
- Through-hole PCB integration without footprint conversion (vs OPA704UA)
- Rail-to-rail signal handling with moderate bandwidth (vs OPA704UA)
設計ノート
Keep the OPA704PA input and feedback connections short, particularly on transimpedance and high-impedance sensor circuits. Place the feedback components directly across the amplifier pins, remove PCB leakage paths around sensitive inputs, and use a protective guard where feasible. Because the specified input bias current is only 1 pA, contamination or connector leakage can dominate the error budget even when the amplifier itself performs well.
Do not treat OPA704PA and OPA704UA as pin-compatible alternatives for an existing board. OPA704PA uses an 8-pin PDIP footprint, whereas OPA704UA is an 8-pin surface-mount device. Direct substitution requires a new footprint and assembly process. Also verify the complete common-mode and output-voltage limits against the actual 12 V supply tolerance rather than assuming that rail-to-rail operation permits operation exactly at either rail.
For gain stages operating close to the 3 MHz gain-bandwidth limit, evaluate closed-loop stability with the actual source impedance, load, and compensation capacitor. The 3 V/µs slew rate also limits large-signal response even when the small-signal bandwidth appears adequate. Use the manufacturer datasheet’s recommended application circuits as the starting point, then verify settling and distortion on the assembled PCB with realistic source and load conditions.
コンプライアンス情報
RoHS compliance is identified for the OPA704PA. No additional REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification claim is made.