OPA743UA - 12 V, 7 MHz CMOS Op Amp | Texas Instruments
部品番号: OPA743UA ✓ 生産中OPA743UA 概要
A CMOS operational amplifier is a voltage-controlled, high-input-impedance amplifier that uses complementary metal-oxide-semiconductor transistors. Within the amplifier hierarchy, the OPA743 belongs to the rail-to-rail I/O CMOS op-amp class, combining low quiescent current with wideband signal handling. Rail-to-rail input operation accepts signals near either supply rail, while the rail-to-rail output stage can approach the output limits under suitable load and output-voltage conditions.
The main features of the OPA743UA include a 7 MHz gain-bandwidth product, 10 V/µs slew rate, 1.1 mA quiescent current, and 84 dB full-scale common-mode rejection ratio. The 12 V maximum single-supply rating supports operation from common laboratory and industrial rails such as 3.3 V, 5 V, and ±5 V, provided the amplifier is not operated beyond its absolute maximum ratings. The low quiescent current makes the device suitable for portable, battery-powered, and low-power sensing systems.
OPA743UA is specified as a single amplifier rather than a dual or quad device. Its wideband CMOS architecture is useful in sensor interfaces, current-to-voltage conversion, audio paths, active filters, and general-purpose voltage amplification. The 8-pin SOIC footprint allows conventional surface-mount assembly and provides a small, readily available package for mixed-signal designs.
In actual circuits, the input common-mode range, output swing, load capacitance, and stability requirements must be checked against the operating conditions rather than inferred from the headline bandwidth. Decoupling capacitors should be placed close to the supply pins, and the unused input pin must be biased so the amplifier does not saturate. The exact noise, offset, input-current, and temperature-range details should be taken from the manufacturer datasheet before releasing a production design.
This page combines the manufacturer product information, distributor package details, application-oriented engineering guidance, and a parameter comparison framework that goes beyond a basic distributor listing. It is intended to help engineers select the amplifier, plan the PCB, and identify when a rail-to-rail single-supply CMOS amplifier is the correct architectural choice.
ドロップイン代替品: OPA743UA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストOPA743UA 最大定格&電気的特性
| Amplifier Type | Single wideband CMOS operational amplifier |
| Number of Circuits | 1 circuit |
| Maximum Single-Supply Voltage | 12 V |
| Dual-Supply Voltage Range | ±6 V |
| Gain-Bandwidth Product | 7 MHz |
| Slew Rate | 10 V/µs |
| 静止電流 | 1.1 mA |
| Full-Scale CMRR | 84 dB |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Process Technology | CMOS |
| パッケージ | 8-pin SOIC |
| Package Type | SO-8 surface mount |
| 実装タイプ | Surface mount |
OPA743UA ピン構成
| ピン 1 | NC — Not connected |
| ピン 2 | IN- — Inverting input |
| ピン 3 | IN+ — Non-inverting input |
| ピン 4 | V- — Negative supply connection |
| ピン 5 | NC — Not connected |
| ピン 6 | OUT — Amplifier output |
| ピン 7 | V+ — Positive supply connection |
| ピン 8 | NC — Not connected |
主な用途
OPA743UA の用途: 6 件s: Sensor Signal Conditioning, Precision Active Filtering, Low-Power Portable Instrumentation, Audio Preamplification, Industrial Control Signal Interface, Data Acquisition Front End.
Sensor Signal Conditioning
The OPA743UA suits sensor front ends that require a wider bandwidth than a precision-only amplifier provides. Its 7 MHz gain-bandwidth product and 10 V/µs slew rate preserve fast sensor transitions, while the 1.1 mA quiescent current supports power-constrained designs. Rail-to-rail input operation is useful when the transducer output moves close to either supply rail. Use the manufacturer's electrical-characteristics tables to confirm input bias current, offset, noise, and common-mode limits for the particular sensor impedance.
おすすめ
Precision Active Filtering
The OPA743UA is appropriate for active filters and measurement amplifiers where a 7 MHz bandwidth exceeds the signal bandwidth. Rail-to-rail I/O increases usable signal range on single-supply systems, and the 10 V/µs slew rate helps maintain low distortion as the filter output changes. Compensation and stability depend on noise gain, load capacitance, and feedback topology, so verify those conditions against the manufacturer datasheet and keep feedback traces short.
おすすめ
Low-Power Portable Instrumentation
The OPA743UA suits portable measurement equipment because its 1.1 mA quiescent current limits supply demand while retaining a 7 MHz gain-bandwidth product. Rail-to-rail input and output operation allows operation from low single-supply rails with a small usable signal range. The amplifier is useful for conditioning low-frequency sensor signals, buffer stages, and conversion front ends. Confirm the exact temperature grade and total noise performance before using it in a precision battery-powered analyzer.
おすすめ
Audio Preamplification
The OPA743UA can amplify low-level audio and microphone signals when the design requires more bandwidth than a general-purpose amplifier. Its rail-to-rail I/O allows operation near the supply rails, and the 10 V/µs slew rate supports moderately demanding signal transitions. Evaluate THD+N, output-noise voltage, and gain-bandwidth behavior at the intended audio frequency from the manufacturer datasheet. Bias a single-supply input near mid-rail to preserve symmetrical output swing.
おすすめ
Industrial Control Signal Interface
The OPA743UA can condition low-level analog control signals in industrial systems that need fast response and low quiescent power. Its 12 V capability accommodates common 12 V-derived analog rails, while rail-to-rail input and output improve range utilization. Use it for interface buffering, transducer amplification, and active gain stages rather than driving long capacitive loads. Confirm operating temperature, supply tolerance, and transient behavior against the manufacturer datasheet for factory equipment.
おすすめ
Data Acquisition Front End
The OPA743UA works as a buffer or gain stage ahead of higher-resolution converters in mixed-signal acquisition systems. The 7 MHz bandwidth provides margin for fast settling, while 1.1 mA quiescent current avoids imposing a large standing load on analog rails. Choose resistor ratios that keep signal swing within the rail-to-rail operating region, and place the amplifier close to the converter input to minimize capacitance and noise pickup. Check settling behavior for the selected closed-loop gain.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA743UA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-pin SOIC |
| Brand | Texas Instruments |
| Maximum Single-Supply Voltage | 12 V |
| Dual-Supply Voltage Range | ±6 V |
| Gain-Bandwidth Product | 7 MHz |
| Slew Rate | 10 V/µs |
| Quiescent Current | 1.1 mA |
| Full-Scale CMRR | 84 dB |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
設計ノート
Place the supply-decoupling capacitor directly beside the positive-supply pin and route the ground return through a low-impedance plane. Keep the non-inverting input, inverting input, and output traces away from the supply capacitor and switching-current paths. For a single-supply circuit, bias the input near mid-supply so the rail-to-rail output stage can swing symmetrically, and use the manufacturer datasheet's recommended decoupling value rather than substituting an arbitrary value.
Do not treat the rail-to-rail designation as an unlimited output-swing guarantee. Output-current demand, temperature, supply voltage, and load capacitance determine how closely the output can approach either rail. Likewise, a single-supply input centered near ground may reduce available linear range. Confirm common-mode and output-swing limits in the manufacturer datasheet, and verify stability at the actual noise gain and capacitive load before releasing the PCB.
The 7 MHz gain-bandwidth product makes the OPA743UA fast enough for short settling windows, but closed-loop performance depends on the selected gain and feedback network. Keep the feedback loop compact, avoid routing the output back beside the input, and terminate unused inputs at a defined common-mode voltage. If the stage drives a cable, ADC input, or other capacitive load, add an isolation resistor near the amplifier and verify the resulting response on test hardware.
コンプライアンス情報
Compliance declarations were not identified in the available manufacturer and distributor records. The OPA743UA is an analog operational amplifier and is not an AEC-Q100-qualified automotive device.