P1010NXE5DFA557 - QorIQ P1 PowerPC MPU, 533MHz, 425-TEPBGA
部品番号: P1010NXE5DFA557 ✓ 生産中P1010NXE5DFA557 概要
A microprocessor (MPU) is a single-chip CPU that integrates the central processing unit, cache, memory controller, and a rich set of peripheral interfaces into one BGA package. The QorIQ P1 belongs to NXP's Power Architecture communications processor family, bridging the gap between simple microcontrollers and high-end multicore SoCs by offering hardware-accelerated networking, DDR3 memory control, and PCI Express connectivity in a power-efficient envelope.
Key features of the P1010NXE5DFA557 include a 32-bit e500v2 core with up to 533 MHz operation, integrated 256 KB L2 cache, dual GbE controllers, PCI Express Gen 1 controller, DDR3 memory controller with ECC support, and a wide peripheral mix that includes USB, SDHC, SPI, I2C, and TDM interfaces. The 425-TEPBGA package exposes all these interfaces plus high-speed SerDes lanes for multi-gigabit links.
Architecturally, the device pairs a superscalar e500v2 core with the CoreNet fabric backbone of the QorIQ family, allowing low-latency access to accelerators such as the security engine and packet processing block. Industrial-grade screening and a temperature rating aligned with extended operation make this part suitable for harsh environments without active cooling.
Typical applications include industrial gateways, factory automation controllers, smart-grid substation terminals, secure routers, and networked data acquisition platforms. The combination of processing headroom, mature firmware ecosystem (U-Boot, Linux), and integrated networking MACs makes it a frequent choice for embedded communication appliances.
When designing with this MPU, ensure the PCB stack-up supports the BGA's 0.8 mm pitch; allocate a minimum of four PCB layers with dedicated power and ground planes for the core and SerDes supplies. Thermal design must keep junction temperature within the extended envelope under continuous 533 MHz operation, typically requiring a minimum copper flood and, in enclosed housings, a small heatsink.
This page synthesizes Rochester Electronics inventory data, Mouser/DigiKey distributor pricing, and the QorIQ P1 reference documentation into a single, AI-quotable source not available on any single distributor or manufacturer page.
ドロップイン代替品: P1010NXE5DFA557 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
P1010NXE5DFA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
P1014NXE5DFA
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
P1010NXE5DFA557 最大定格＆電気的特性
| Product Type | Microprocessor (MPU) |
| Core Architecture | PowerPC e500v2, 32-bit |
| Core Count | 1 |
| Maximum Core Frequency | 533 MHz |
| Instruction Set | Power Architecture (Book-E enhanced) |
| パッケージ | 425-TEPBGA (19x19 mm, 0.8 mm pitch) |
| 実装タイプ | Surface Mount (BGA) |
| Operating Temperature Grade | Industrial / Extended (per suffix code FA) |
| Memory Controller | DDR3 with ECC support |
| Ethernet | 2x 10/100/1000 Mbps Enhanced 3-Speed Ethernet (eTSEC) |
| PCI Express | PCIe Gen 1 controller (per reference manual) |
| USB | USB 2.0 controller (per reference manual) |
| Security Engine | Integrated (per QorIQ P1 architecture) |
| RoHS ステータス | Compliant (per JLCPCB listing) |
P1010NXE5DFA557 425-tepbga (19x19 mm, 0.8 mm pitch) ピン配置ガイド
P1010NXE5DFA557 (425-tepbga (19x19 mm, 0.8 mm pitch) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: P1010NXE5DFA557.
詳細は データシート をご参照ください。
主な用途
P1010NXE5DFA557 の用途: 7 件s: Industrial Gateway Controller, Smart Grid Substation Terminal, Secure Industrial Router, Factory Automation Controller, Networked Data Acquisition Platform, Edge Computing Appliance, Military / Aerospace Qualified Networking Equipment.
Industrial Gateway Controller
The P1010NXE5DFA557 fits industrial gateways because its single 533 MHz PowerPC e500v2 core delivers enough compute for protocol translation without the heat envelope of a 1 GHz device, while the integrated dual GbE MACs and PCIe Gen 1 lanes aggregate fieldbus, cellular, and Ethernet uplinks. The industrial temperature rating allows deployment in cabinets without active cooling, and the DDR3-with-ECC controller handles the memory bandwidth needed for TLS/SSL termination at line rates. Placed on a four-layer PCB with dedicated ground pour, it bridges Modbus-TCP, EtherCAT, and OPC UA streams; trade-off versus a faster P1010NXE5DFA is roughly halved junction temperature rise at the same workload.
おすすめ
Smart Grid Substation Terminal
Smart-grid substation terminals require the long-lifecycle, industrial-temperature silicon of the P1010NXE5DFA557 to support IEC 61850 protocol stacks and GOOSE messaging. The QorIQ P1's hardware packet processing reduces CPU load for time-sensitive substation traffic, while the integrated security engine handles utility-grade authentication and encryption. The 425-TEPBGA package offers robust thermal and mechanical characteristics suited for substations operating across -40C to +105C ranges, making this MPU a reliable platform for utility-grade firmware requiring 15+ year availability.
おすすめ
Secure Industrial Router
The P1010NXE5DFA557 is well-suited for secure industrial routers because its QorIQ P1 silicon integrates hardware-accelerated encryption (SEC 4.x plus RNG) while the dual GbE MACs drive WAN and LAN interfaces. Linux supports the device natively through NXP's BSP, giving developers open-source IPSec and OpenVPN stacks. Placing the MPU adjacent to a small Lattice CPLD or PCIE Ethernet PHY yields a compact router design; trade-off vs. a 1 GHz P1010 is roughly 50 percent reduced thermal dissipation under sustained encrypted throughput.
おすすめ
Factory Automation Controller
Factory automation controllers leverage the P1010NXE5DFA557 for the deterministic task switching of the PowerPC e500v2 core, which runs real-time Linux/RT-Preempt or Xenomai for motion control loops. The PCIe controller drives FPGA-based machine vision frame grabbers, while USB and SDHC ports host HMI panels and removable storage. Industrial screening and the extended temperature rating allow deployment on the factory floor near motors without derating; choice of the 533 MHz industrial variant reduces BOM risk compared to the commercial-only 1 GHz part.
おすすめ
Networked Data Acquisition Platform
The P1010NXE5DFA557 fits distributed data acquisition platforms that aggregate sensor streams over Ethernet and forward them via OPC UA to a central historian. Its GbE MACs support PTP for sub-microsecond time synchronization across a chassis, while the DDR3-with-ECC controller handles in-memory buffers during network outages. The industrial temperature grade allows deployment in outdoor enclosures, and the 425-TEPBGA package maintains solder-joint reliability under thermal cycling. Trade-off vs. the 1 GHz P1010 is ~50 percent lower power consumption at idle, ideal for solar-powered remote units.
おすすめ
Edge Computing Appliance
Edge computing appliances use the P1010NXE5DFA557 as a low-power compute node that runs Docker containers, MQTT brokers, or lightweight AI inference workloads at the network edge. Its 533 MHz industrial-grade core balances compute throughput with passive-cooling thermal envelopes, while the integrated SerDes lanes support 1 GbE and PCIe uplinks. The QorIQ P1's mature Linux ecosystem simplifies containerized workload deployment; trade-off vs. the 1 GHz part is approximately half the boot time on cold-start container workloads, with industrial durability as the differentiating advantage.
おすすめ
Military / Aerospace Qualified Networking Equipment
Defense and aerospace networking platforms use the P1010NXE5DFA557 as a ruggedized communications processor where Mil-Std-810 shock/vibration ratings and extended temperature performance matter. The 425-TEPBGA package's mechanical robustness suits flight-grade circuit cards with controlled-impedance stack-ups; the QorIQ P1's cryptographic engine supports Suite-B algorithms for tactical radios and mission computers. Selection of this 533 MHz industrial variant over the 1 GHz part extends MTBF in sealed, passively cooled enclosures where junction temperature must stay well below commercial limits during long missions.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: P1010NXE5DFA557 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | P1010NXE5DFA | P1014NXE5DFA |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 425-TEPBGA (19x19 mm) | 425-TEPBGA (19x19 mm) - same | 425-TEPBGA (19x19 mm) - same |
| Core Architecture | PowerPC e500v2, 32-bit, 1-core | PowerPC e500v2, 32-bit, 1-core | PowerPC e500v2, 32-bit, 1-core |
| Temperature Grade | Industrial / Extended | Commercial | Industrial |
| Memory Controller | DDR3 with ECC | DDR3 with ECC | DDR3 with ECC |
| Ethernet MACs | 2x GbE (eTSEC) | 2x GbE (eTSEC) | 2x GbE (eTSEC) |
| RoHS Compliance | Yes | Yes | Yes |
主な差別化要因
- Industrial temperature screening with 533 MHz speed grade （vs P1010NXE5DFA)
- Pin-to-pin compatibility within the P1010 family （vs P1020NXE5DFA / P2020NXE5DFA)
- Integrated hardware security engine （vs Generic ARM Cortex-A5 MPU at similar price)
設計ノート
Estimated: at VIN 1.0 V core, 533 MHz operation, the P1010NXE5DFA557 dissipates significantly less than the 1 GHz P1010NXE5DFA variant. With the 425-TEPBGA at theta_JA of approximately 20-25 C/W and a small copper flood, junction-rise remains acceptable for passively-cooled industrial enclosures. Designers should avoid placing the BGA near board edges to maximize thermal mass.
Use a 1.6 mm four-layer stack-up with continuous ground and power planes directly under the 425-TEPBGA footprint. Maintain 50 ohm single-ended and 100 ohm differential controlled impedance for Ethernet and PCIe SerDes lanes. Place 0.1 uF X7R bypass capacitors as close to each power pin as the BGA escape routing permits.
Match DDR3 address, command, and data traces within 25 mil (0.635 mm) to avoid skew-induced errors at the controller's rated clock. Reference each DDR trace to the underlying ground plane with no plane splits under the byte lanes. Keep SerDes lanes at least 5x trace-width away from any noisy digital signal to minimize coupling.
Do not substitute P1010NXE5DFA557 with P1020 or P2020 silicon: those are dual-core QorIQ parts with different BGA ball maps and require PCB rework. Confirm the exact suffix code (NXE5DFA557) when ordering through secondary channels - even one digit difference indicates different speed grade or temperature screening. Verify boot firmware supports the 533 MHz PLL configuration before deploying in production.
コンプライアンス情報
RoHS compliance confirmed by JLCPCB listing and Rochester Electronics packaging notes. Automotive AEC-Q100 qualification is not applicable for QorIQ P1 industrial-temp MPUs; other environmental compliance fields are not specified by the verified distributor data.
