PCA9538PWG4 - 8-Bit I2C I/O Expander | Texas Instruments
部品番号: PCA9538PWG4 ✓ 生産中PCA9538PWG4 概要
An I/O expander is a peripheral interface IC that extends the number of digital lines accessible through a serial bus. In the hierarchy of interface semiconductors, this device is an I2C GPIO expander, an interface IC, and ultimately a general-purpose semiconductor. The PCA9538PWG4 uses two serial signals, SCL and SDA, to transfer configuration and output data between the host and the eight port pins. An interrupt output allows the host to respond when a change occurs on an input port.
Key features include eight independently configurable I/O lines, support for both I2C and SMBus operation, and a maximum bus clock frequency of 400 kHz. The 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems. Separate address inputs allow multiple expanders to share a bus when their hardware address assignments differ, while the reset input provides a defined startup state. Configuration registers provide control over input and output operation.
The PCA9538 performs remote port updates over the serial interface, reducing the number of host pins required for keypad matrices, control signals, or digital status monitoring. Its low-power I/O-expander design is suitable for embedded control, industrial automation, communications equipment, and consumer products. The device can operate as an 8-bit parallel port while the host controller reads or writes the port data through I2C. Interrupt signaling helps avoid continuous polling when an attached circuit changes an input state.
Typical uses include expanding MCU GPIO for relay-control boards, monitoring switch banks, driving addressable display or LED-control lines, and adding isolated digital interfaces to industrial controllers. The 400 kHz I2C rate also permits the device to coexist with moderate-speed bus traffic. Designers should account for pull-up resistors on SDA and SCL, assign a unique device address, and ensure that the host voltage and all attached port voltages remain within the device's operating limits.
For PCB implementation, place the device close to the I2C controller and route SDA and SCL away from noisy switching nodes. The TSSOP-16 footprint requires adequate copper and assembly clearance for its 0.65 mm lead pitch. Decoupling capacitance should be placed at the supply pin according to the manufacturer datasheet, and the reset, address, port, and interrupt traces should be checked for signal integrity at the maximum 400 kHz bus rate.
This page combines the manufacturer function description, package information, pin assignments, application guidance, drop-in alternatives, and practical design considerations. It is intended to help engineers identify whether the PCA9538PWG4 fits an existing 16-pin TSSOP design and how to integrate its serial interface, address assignment, and interrupt-driven I/O expansion correctly.
ドロップイン代替品: PCA9538PWG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PCA9538PWG4 (同一形状・フットプリント) — 相違点: Number of I/O Ports, Interface, Package, Configuration Registers.
PCA9538PW,118
✅ ドロップイン📋 参考代替品(カタログ未掲載)
PCA9538APWJ
✅ ドロップイン価格はお問い合わせください
データシートを見る →PCA9538PW
✅ ドロップイン✓ 在庫あり
$0.5086 / 個
データシートを見る →PCA9538PWG4 仕様
| Number of I/O Ports | 8 bits |
| インターフェース | I2C and SMBus |
| Maximum I2C Clock Frequency | 400 kHz |
| Operating Supply Voltage Range | 2.3 V to 5.5 V |
| パッケージ | 16-pin TSSOP |
| Package Width | 4.40 mm |
| Number of Terminals | 16 |
| 実装タイプ | Surface mount |
| Lead Form | Gull wing |
| Temperature Grade | Industrial |
| Interrupt Output | 1 output |
| Reset Input | 1 input |
| Configuration Registers | Included |
PCA9538PWG4 ピン構成
| ピン 1 | INT — Active-low interrupt output |
| ピン 2 | P0 — Bidirectional I/O port 0 |
| ピン 3 | P1 — Bidirectional I/O port 1 |
| ピン 4 | P2 — Bidirectional I/O port 2 |
| ピン 5 | P3 — Bidirectional I/O port 3 |
| ピン 6 | P4 — Bidirectional I/O port 4 |
| ピン 7 | P5 — Bidirectional I/O port 5 |
| ピン 8 | P6 — Bidirectional I/O port 6 |
| ピン 9 | P7 — Bidirectional I/O port 7 |
| ピン 10 | GND — Ground connection |
| ピン 11 | GND — Ground connection |
| ピン 12 | SCL — Serial clock input |
| ピン 13 | SDA — Serial data input and output |
| ピン 14 | A0 — Hardware address input 0 |
| ピン 15 | A1 — Hardware address input 1 |
| ピン 16 | VCC — Power supply input |
主な用途
PCA9538PWG4 の用途: 6 件s: Industrial Relay and Control Signal Expansion, Keypad and Switch Matrix Monitoring, LED and Display Control Expansion, Automotive Access and Body-Control Interfaces, Communications Equipment Status and Control, Embedded Product and IoT Peripheral Control.
Industrial Relay and Control Signal Expansion
The PCA9538PWG4 fits industrial controller boards that need more digital control outputs than the host MCU can provide directly. Its eight port pins operate from a 2.3 V to 5.5 V supply and are accessed through a 400 kHz I2C or SMBus interface, allowing a compact controller to drive discrete logic, relay-driver inputs, alarm lines, or actuator-enable signals. The host writes output states through the port register, while the interrupt output can identify changes on ports configured as inputs. Because the 16-pin TSSOP footprint is compact, the expander can be placed near the controlled circuitry without adding eight dedicated MCU routes. Designers should verify relay-driver input levels, isolate high-voltage contacts, and keep the serial bus away from switching transients.
おすすめ
Keypad and Switch Matrix Monitoring
The PCA9538PWG4 is suitable for monitoring keypad rows, selector switches, limit sensors, and other discrete contacts in a compact embedded product. Eight digital ports can read switch states while the I2C host retrieves the port data at up to 400 kHz. When a port is configured for input change detection, the interrupt line alerts the host without requiring continuous serial polling. This is particularly useful in control panels where conserving microcontroller GPIO pins and reducing wiring complexity are priorities. The interface operates from 2.3 V to 5.5 V, supporting both 3.3 V and 5 V logic systems. PCB implementation should include appropriate debounce or filtering at the contacts, ensure pull-ups match the bus voltage, and isolate long switch wiring from sensitive clock and serial traces.
おすすめ
LED and Display Control Expansion
The PCA9538PWG4 can extend a host controller into LED indicators, display-enable signals, mode selectors, and panel-control logic. Its eight configurable I/O lines provide a practical way to manage static indicators without dedicating eight MCU pins, while the 400 kHz I2C interface keeps serial traffic compatible with embedded communication links. The 2.3 V to 5.5 V operating range permits use in both 3.3 V and 5 V product architectures. If the ports drive LEDs directly, current limits, drive voltage, and thermal conditions must be checked against the manufacturer datasheet; otherwise, the outputs can control transistor or LED-driver inputs. Keep the expander away from display power converters and route SDA and SCL as short, continuous traces with appropriate pull-up resistors.
おすすめ
Automotive Access and Body-Control Interfaces
The PCA9538PWG4 can serve as a remote I/O interface in automotive body-control, access, and comfort systems where a central controller must monitor switches or control low-current logic stages. Its 8-bit port, 400 kHz serial interface, industrial temperature grade, and 2.3 V to 5.5 V supply range provide a compact way to reduce direct host-controller pin demand. The interrupt output supports event-driven handling of door, latch, or auxiliary switch status, although vehicle programs must confirm the required automotive qualification for the exact production context. Protection against reverse voltage, load dump, ESD, and transient pulses should be implemented according to the vehicle platform requirements. Keep unprotected connector routes away from the TSSOP and route ground returns to reduce susceptibility to conducted automotive noise.
おすすめ
Communications Equipment Status and Control
The PCA9538PWG4 is useful in communications equipment that needs front-panel indicators, relay-control signals, fan enables, or equipment-status inputs beyond the available host pins. A 400 kHz I2C or SMBus connection allows the central processor to update eight output lines efficiently, while interrupt input monitoring can flag a changed module state. Its 16-pin TSSOP package supports compact line-card and gateway designs, and the 2.3 V to 5.5 V supply range accommodates common communication-system rails. Because I2C transactions add serial overhead, use output latches for static states and reserve rapid toggling for signals that do not require deterministic sub-microsecond updates. Maintain bus pull-up values appropriate for the voltage and capacitance, and separate switching-regulator routing from the serial lines.
おすすめ
Embedded Product and IoT Peripheral Control
The PCA9538PWG4 fits compact embedded and IoT products that need additional buttons, status LEDs, sensor enables, or low-speed actuator controls. Eight independently configurable lines share the serial bus with other addressable peripherals, reducing the number of direct microcontroller pins and simplifying wiring. The device supports a 2.3 V to 5.5 V supply range and a maximum I2C clock of 400 kHz, making it practical for 3.3 V battery-powered products and 5 V powered appliances. The interrupt output allows the host to sleep between relevant changes, which can reduce unnecessary processing. Firmware should assign a unique address, initialize the port direction registers, and handle reset initialization. Hardware design should account for bus pull-up current in low-power states and provide adequate copper thermal capacity around the TSSOP package.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PCA9538PWG4 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PCA9538PW,118 | PCA9538APW | PCA9538PW |
|---|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
| Number of I/O Ports | 8 bits | 8 bits | 8 bits | 8 bits |
| Serial Interface | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Maximum Clock Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Operating Supply Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Interrupt Output | Included | Included | Included | Included |
| Reset and Configuration Registers | Included | Included | Included | Included |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
主な差別化要因
- Eight configurable lines from a 16-pin TSSOP device (vs PCA9538APW)
- Documented pin-to-pin cross-brand replacement path (vs PCA9538PW)
- Same core interface ratings across the qualified drop-in options (vs PCA9538PW,118)
設計ノート
Place the PCA9538PWG4 close to the host controller and the circuits using its eight port pins. Keep SDA and SCL traces short, route them away from switching-regulator power paths, and provide pull-up resistors to the interface voltage. The TSSOP-16 body and 0.65 mm lead pitch require assembly clearance for the exposed leads. Keep both ground pins connected to a low-impedance ground plane and use a solid ground reference beneath the device where practical.
Do not connect the address inputs, reset input, or port pins in a way that creates a conflict with their configured directions. Confirm the address pins during power-up so multiple expanders receive distinct I2C addresses. Reset must not be left floating, and external devices must not contend with an SDA pin during a write. Read the manufacturer register definitions before changing polarity or direction because a configuration sequence can temporarily place a pin in an unexpected state.
Use the device within its documented 2.3 V to 5.5 V supply range and calculate the total load on VCC and the I2C pull-up network before fixing the supply budget. Port output current, input leakage, bus pull-up current, and any attached indicator loads all contribute to system power. Check the pin-level drive and sink ratings in the manufacturer datasheet, especially when a port drives LEDs or when multiple outputs are active simultaneously.
The maximum supported I2C clock frequency is 400 kHz, but the usable rate also depends on bus capacitance, pull-up strength, trace length, and the clock and data rise-time requirements. Avoid long stubs on SDA or SCL. If the expander is located near a connector or switching circuit, use series damping where necessary and verify timing with an oscilloscope at the farthest bus node.
コンプライアンス情報
The industrial temperature grade identifies the product's intended operating class but does not itself establish RoHS, REACH, automotive, lead-free, halogen-free, or conflict-minerals compliance.