Texas Instruments

PCA9538PWG4 - 8-Bit I2C I/O Expander | Texas Instruments

N.º de pieza: PCA9538PWG4 ✓ Activo
2.3 V to 5.5 V Vdss 16-pin TSSOP Package 400 kHz Speed
MOQ: 1 |

PCA9538PWG4 Descripción general

The Texas Instruments PCA9538PWG4 is an 8-bit I/O expander with an I2C or SMBus host interface, a maximum clock frequency of 400 kHz, and a 2.3 V to 5.5 V operating supply range. The device is packaged in a 16-pin TSSOP with gull-wing leads and an industrial temperature grade. It adds eight remotely controlled digital input or output ports to a host processor without consuming eight direct GPIO pins.

An I/O expander is a peripheral interface IC that extends the number of digital lines accessible through a serial bus. In the hierarchy of interface semiconductors, this device is an I2C GPIO expander, an interface IC, and ultimately a general-purpose semiconductor. The PCA9538PWG4 uses two serial signals, SCL and SDA, to transfer configuration and output data between the host and the eight port pins. An interrupt output allows the host to respond when a change occurs on an input port.

Key features include eight independently configurable I/O lines, support for both I2C and SMBus operation, and a maximum bus clock frequency of 400 kHz. The 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems. Separate address inputs allow multiple expanders to share a bus when their hardware address assignments differ, while the reset input provides a defined startup state. Configuration registers provide control over input and output operation.

The PCA9538 performs remote port updates over the serial interface, reducing the number of host pins required for keypad matrices, control signals, or digital status monitoring. Its low-power I/O-expander design is suitable for embedded control, industrial automation, communications equipment, and consumer products. The device can operate as an 8-bit parallel port while the host controller reads or writes the port data through I2C. Interrupt signaling helps avoid continuous polling when an attached circuit changes an input state.

Typical uses include expanding MCU GPIO for relay-control boards, monitoring switch banks, driving addressable display or LED-control lines, and adding isolated digital interfaces to industrial controllers. The 400 kHz I2C rate also permits the device to coexist with moderate-speed bus traffic. Designers should account for pull-up resistors on SDA and SCL, assign a unique device address, and ensure that the host voltage and all attached port voltages remain within the device's operating limits.

For PCB implementation, place the device close to the I2C controller and route SDA and SCL away from noisy switching nodes. The TSSOP-16 footprint requires adequate copper and assembly clearance for its 0.65 mm lead pitch. Decoupling capacitance should be placed at the supply pin according to the manufacturer datasheet, and the reset, address, port, and interrupt traces should be checked for signal integrity at the maximum 400 kHz bus rate.

This page combines the manufacturer function description, package information, pin assignments, application guidance, drop-in alternatives, and practical design considerations. It is intended to help engineers identify whether the PCA9538PWG4 fits an existing 16-pin TSSOP design and how to integrate its serial interface, address assignment, and interrupt-driven I/O expansion correctly.

Alternativas directas para PCA9538PWG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con PCA9538PWG4 (mismo factor de forma y huella) — difiere en Number of I/O Ports, Interface, Package, Configuration Registers.

NXP Semiconductors
Number of I/O Ports: 8 ports
Interface: I2C-bus and SMBus
Package: TSSOP-16
Comparar con PCA9538PWG4 →
NXP Semiconductors
Number of I/O Ports: 8
Interface: I2C-bus and SMBus
Package: TSSOP-16
Comparar con PCA9538PWG4 →

PCA9538PW,118

✅ Sustitución directa
📦 16-pin TSSOP
Same 8-bit 400 kHz I2C/SMBus interface and 16-pin TSSOP footprint; the ordering code identifies a 118 temperature-grade shipment form, while electrical differences are 0% for the stated core ratings.

📋 Alternativa de referencia (no en el catálogo)

PCA9538APWJ

✅ Sustitución directa
NXP Semiconductors
📦 16-pin TSSOP
8-bit general-purpose I/O expander · 8 ports · I2C-bus and SMBus · 400 kHz · 100 kHz to 400 kHz · 2.3 V to 5.5 V · 5.5 V · Yes, 1 interrupt output

Consulte el precio

Ver hoja de datos →

PCA9538PW

✅ Sustitución directa
NXP Semiconductors
📦 16-pin TSSOP
8-bit I2C-bus/SMBus I/O expander · 8 · 2.3 V to 5.5 V · I2C-bus and SMBus · 400 kHz · Yes · Yes · Yes

✓ En stock

$0.5086 / unidad

Ver hoja de datos →

PCA9538PWG4 Especificaciones

Number of I/O Ports 8 bits
Interfaz I2C and SMBus
Maximum I2C Clock Frequency 400 kHz
Operating Supply Voltage Range 2.3 V to 5.5 V
Encapsulado 16-pin TSSOP
Package Width 4.40 mm
Number of Terminals 16
Tipo de montaje Surface mount
Lead Form Gull wing
Temperature Grade Industrial
Interrupt Output 1 output
Reset Input 1 input
Configuration Registers Included

Configuración de pines de PCA9538PWG4

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
Pin 1 INT — Active-low interrupt output
Pin 2 P0 — Bidirectional I/O port 0
Pin 3 P1 — Bidirectional I/O port 1
Pin 4 P2 — Bidirectional I/O port 2
Pin 5 P3 — Bidirectional I/O port 3
Pin 6 P4 — Bidirectional I/O port 4
Pin 7 P5 — Bidirectional I/O port 5
Pin 8 P6 — Bidirectional I/O port 6
Pin 9 P7 — Bidirectional I/O port 7
Pin 10 GND — Ground connection
Pin 11 GND — Ground connection
Pin 12 SCL — Serial clock input
Pin 13 SDA — Serial data input and output
Pin 14 A0 — Hardware address input 0
Pin 15 A1 — Hardware address input 1
Pin 16 VCC — Power supply input

Aplicaciones típicas

PCA9538PWG4 es adecuado para 6 aplicacións: Industrial Relay and Control Signal Expansion, Keypad and Switch Matrix Monitoring, LED and Display Control Expansion, Automotive Access and Body-Control Interfaces, Communications Equipment Status and Control, Embedded Product and IoT Peripheral Control.

🏭

Industrial Relay and Control Signal Expansion

The PCA9538PWG4 fits industrial controller boards that need more digital control outputs than the host MCU can provide directly. Its eight port pins operate from a 2.3 V to 5.5 V supply and are accessed through a 400 kHz I2C or SMBus interface, allowing a compact controller to drive discrete logic, relay-driver inputs, alarm lines, or actuator-enable signals. The host writes output states through the port register, while the interrupt output can identify changes on ports configured as inputs. Because the 16-pin TSSOP footprint is compact, the expander can be placed near the controlled circuitry without adding eight dedicated MCU routes. Designers should verify relay-driver input levels, isolate high-voltage contacts, and keep the serial bus away from switching transients.

🧩

Keypad and Switch Matrix Monitoring

The PCA9538PWG4 is suitable for monitoring keypad rows, selector switches, limit sensors, and other discrete contacts in a compact embedded product. Eight digital ports can read switch states while the I2C host retrieves the port data at up to 400 kHz. When a port is configured for input change detection, the interrupt line alerts the host without requiring continuous serial polling. This is particularly useful in control panels where conserving microcontroller GPIO pins and reducing wiring complexity are priorities. The interface operates from 2.3 V to 5.5 V, supporting both 3.3 V and 5 V logic systems. PCB implementation should include appropriate debounce or filtering at the contacts, ensure pull-ups match the bus voltage, and isolate long switch wiring from sensitive clock and serial traces.

💡

LED and Display Control Expansion

The PCA9538PWG4 can extend a host controller into LED indicators, display-enable signals, mode selectors, and panel-control logic. Its eight configurable I/O lines provide a practical way to manage static indicators without dedicating eight MCU pins, while the 400 kHz I2C interface keeps serial traffic compatible with embedded communication links. The 2.3 V to 5.5 V operating range permits use in both 3.3 V and 5 V product architectures. If the ports drive LEDs directly, current limits, drive voltage, and thermal conditions must be checked against the manufacturer datasheet; otherwise, the outputs can control transistor or LED-driver inputs. Keep the expander away from display power converters and route SDA and SCL as short, continuous traces with appropriate pull-up resistors.

🚗

Automotive Access and Body-Control Interfaces

The PCA9538PWG4 can serve as a remote I/O interface in automotive body-control, access, and comfort systems where a central controller must monitor switches or control low-current logic stages. Its 8-bit port, 400 kHz serial interface, industrial temperature grade, and 2.3 V to 5.5 V supply range provide a compact way to reduce direct host-controller pin demand. The interrupt output supports event-driven handling of door, latch, or auxiliary switch status, although vehicle programs must confirm the required automotive qualification for the exact production context. Protection against reverse voltage, load dump, ESD, and transient pulses should be implemented according to the vehicle platform requirements. Keep unprotected connector routes away from the TSSOP and route ground returns to reduce susceptibility to conducted automotive noise.

🌐

Communications Equipment Status and Control

The PCA9538PWG4 is useful in communications equipment that needs front-panel indicators, relay-control signals, fan enables, or equipment-status inputs beyond the available host pins. A 400 kHz I2C or SMBus connection allows the central processor to update eight output lines efficiently, while interrupt input monitoring can flag a changed module state. Its 16-pin TSSOP package supports compact line-card and gateway designs, and the 2.3 V to 5.5 V supply range accommodates common communication-system rails. Because I2C transactions add serial overhead, use output latches for static states and reserve rapid toggling for signals that do not require deterministic sub-microsecond updates. Maintain bus pull-up values appropriate for the voltage and capacitance, and separate switching-regulator routing from the serial lines.

📱

Embedded Product and IoT Peripheral Control

The PCA9538PWG4 fits compact embedded and IoT products that need additional buttons, status LEDs, sensor enables, or low-speed actuator controls. Eight independently configurable lines share the serial bus with other addressable peripherals, reducing the number of direct microcontroller pins and simplifying wiring. The device supports a 2.3 V to 5.5 V supply range and a maximum I2C clock of 400 kHz, making it practical for 3.3 V battery-powered products and 5 V powered appliances. The interrupt output allows the host to sleep between relevant changes, which can reduce unnecessary processing. Firmware should assign a unique address, initialize the port direction registers, and handle reset initialization. Hardware design should account for bus pull-up current in low-power states and provide adequate copper thermal capacity around the TSSOP package.

What is the PCA9538PWG4 and what does it do?
The PCA9538PWG4 is an 8-bit I2C and SMBus I/O expander that adds eight digital port lines to a host processor. According to the Texas Instruments manufacturer datasheet, it operates from 2.3 V to 5.5 V, supports a maximum bus clock frequency of 400 kHz, and provides interrupt, reset, configuration, and port registers. The device is packaged in a 16-pin TSSOP for surface-mount PCB designs.
What is the operating voltage range of PCA9538PWG4?
The PCA9538PWG4 operates from 2.3 V to 5.5 V. The Texas Instruments manufacturer datasheet identifies the device as suitable for low-voltage embedded systems, including 3.3 V and 5 V rails. The host processor, pull-up resistors, and attached I/O circuitry should use compatible voltage levels, and external circuitry must not drive a port beyond the limits stated in the datasheet.
Where can I download the PCA9538PWG4 datasheet PDF?
The official PCA9538PWG4 datasheet PDF is available from the Texas Instruments product documentation at https://www.ti.com/lit/ds/symlink/pca9538.pdf. The manufacturer datasheet contains the register map, electrical characteristics, timing diagrams, pin descriptions, and application information needed to design the serial interface and verify power, logic-level, and bus-timing constraints.
Where can I find the PCA9538PWG4 pinout?
The PCA9538PWG4 pinout is shown in the Texas Instruments manufacturer datasheet and corresponds to the 16-pin TSSOP layout. Pins 2 through 9 are P0 through P7, pins 12 and 13 are SCL and SDA, pins 14 and 15 are the address inputs, and the remaining pins provide power, ground, reset, and interrupt functions. Use the pin-description table when assigning PCB tracks.
Can PCA9538PWG4 be used with a 3.3 V I2C bus?
Yes, the PCA9538PWG4 can operate in a 3.3 V system because its documented supply range is 2.3 V to 5.5 V. The I2C pull-up network should be connected to the appropriate 3.3 V rail, and the host and expander must share compatible logic levels. The manufacturer datasheet also specifies operation on a 400 kHz I2C bus.
How does the PCA9538PWG4 interrupt output work?
The PCA9538PWG4 provides an active-low interrupt output that lets the host detect a change on one of the configured input ports. According to the Texas Instruments manufacturer datasheet, the interrupt configuration registers determine which port transitions activate the indication. This avoids continuous I2C polling and helps conserve host processing time in keypad, switch-monitoring, and industrial sensing systems.
Where can I buy PCA9538PWG4 and check current availability?
Use the Request a Quote form on this page to request current PCA9538PWG4 availability, minimum order quantity, and lead time. The request can identify the exact 16-pin TSSOP package and the G4 shipment form, helping procurement confirm the correct ordering code. Current supply status should be confirmed at the time of quotation because component inventory and manufacturing schedules can change.
What is the price of PCA9538PWG4?
Use the Request a Quote form on this page for the current PCA9538PWG4 unit price and volume pricing. The quote should reference the exact MPN PCA9538PWG4, its 16-pin TSSOP package, and the required quantity. Requesting the formal quotation allows the order to be evaluated against current component availability, packaging, and lead time.
What is the lead time for PCA9538PWG4?
Current lead time for PCA9538PWG4 should be confirmed through the Request a Quote form on this page. Include the required quantity, target shipment date, and acceptable packaging in the request. The manufacturer lists the device as an 8-bit, 400 kHz I2C and SMBus expander in a 16-pin TSSOP, allowing procurement to verify the exact component before committing to a schedule.
Is PCA9538PWG4 in stock?
Stock for PCA9538PWG4 is quote-time information and should be checked through the Request a Quote form on this page. Submit the quantity and target delivery date to obtain a current availability response. The exact orderable identifier is PCA9538PWG4, which combines the PCA9538 device with the 16-pin TSSOP package and G4 commercial shipment form.
What is the difference between PCA9538PWG4 and PCA9538APW?
The PCA9538PWG4 is the Texas Instruments 16-pin TSSOP version, while PCA9538APW is the NXP version identified as a pin-to-pin replacement for the PCA9538. According to the NXP product information, the PCA9538A is a more fully functional device with added capabilities. Both provide an 8-bit low-power serial I/O expander, but software register behavior and detailed electrical limits should be compared before substitution.
Can PCA9538APW replace PCA9538PWG4 on an existing PCB?
Yes, the PCA9538APW can serve as a pin-to-pin replacement for PCA9538 devices when the PCB uses the compatible 16-pin TSSOP footprint. The NXP product page explicitly describes it as a pin-to-pin replacement for the PCA9538. Before substitution, verify the address configuration, reset behavior, interrupt polarity, register map, and electrical limits in both manufacturer datasheets.
When should I choose PCA9538PWG4 over a direct MCU GPIO port?
Choose PCA9538PWG4 when conserving host GPIO pins is more important than maximizing switching speed. It provides eight digital lines through two shared serial signals, supports 400 kHz I2C, and adds interrupt-driven change notification. A direct MCU GPIO port is preferable for frequent high-speed toggling, because each I2C register transaction consumes bus time and introduces protocol overhead.
Is PCA9538PWG4 suitable for industrial control and automation?
The PCA9538PWG4 is suitable for many industrial control and automation designs because it is identified as an industrial-temperature-grade, 8-bit I2C and SMBus expander in a 16-pin TSSOP. It can monitor switch inputs, interface with control signals, and provide interrupt-driven status updates. The final design must remain within the datasheet limits for supply voltage, I/O current, temperature, and bus timing.
What can replace PCA9538PWG4?
PCA9538APW from NXP is a documented pin-to-pin replacement for the PCA9538 family and uses the compatible 16-pin TSSOP package. PCA9538PW,118 is another 16-pin TSSOP ordering option identified as having consistent terminals, packages, and principal performance characteristics. Review reset, interrupt, address, and register compatibility against the Texas Instruments manufacturer datasheet before replacing an assembled design.
What are the key specifications of PCA9538PWG4 that engineers should know?
The PCA9538PWG4 provides eight configurable digital I/O lines, I2C and SMBus connectivity, a 400 kHz maximum clock frequency, and a 2.3 V to 5.5 V operating supply range. It uses a 16-pin TSSOP package, includes reset and interrupt functions, and has an industrial temperature grade. The Texas Instruments manufacturer datasheet also defines the address, port, polarity, and configuration registers used in firmware.

Datos de referencia de ingeniería para PCA9538PWG4 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose PCA9538PWG4 when the design needs eight low-speed digital lines, an I2C or SMBus host interface, and a 16-pin TSSOP footprint. Select PCA9538PW,118 when procurement wants a Texas Instruments ordering option with the same principal interface ratings and package. Consider PCA9538APW when its additional PCA9538A functions are useful; NXP identifies it as a pin-to-pin replacement, but firmware should still be checked for register, reset, and interrupt differences. PCA9538PW is another compatible 16-pin TSSOP option for source diversification. A direct microcontroller GPIO port remains preferable for signals requiring frequent high-speed changes because every expander update uses the serial bus. For any substitution, verify power voltage, address mapping, port direction, reset timing, interrupt polarity, and the manufacturer electrical limits before releasing the PCB.

Comparación con alternativas

Parámetro Este producto PCA9538PW,118 PCA9538APW PCA9538PW
Package 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP
Brand Texas Instruments Texas Instruments NXP Semiconductors NXP Semiconductors
Number of I/O Ports 8 bits 8 bits 8 bits 8 bits
Serial Interface I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus
Maximum Clock Frequency 400 kHz 400 kHz 400 kHz 400 kHz
Operating Supply Voltage 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
Interrupt Output Included Included Included Included
Reset and Configuration Registers Included Included Included Included
Mounting Type Surface mount Surface mount Surface mount Surface mount

Diferenciadores clave

  • Eight configurable lines from a 16-pin TSSOP device (frente a PCA9538APW)
  • Documented pin-to-pin cross-brand replacement path (frente a PCA9538PW)
  • Same core interface ratings across the qualified drop-in options (frente a PCA9538PW,118)

Notas de diseño

Place the PCA9538PWG4 close to the host controller and the circuits using its eight port pins. Keep SDA and SCL traces short, route them away from switching-regulator power paths, and provide pull-up resistors to the interface voltage. The TSSOP-16 body and 0.65 mm lead pitch require assembly clearance for the exposed leads. Keep both ground pins connected to a low-impedance ground plane and use a solid ground reference beneath the device where practical.

Do not connect the address inputs, reset input, or port pins in a way that creates a conflict with their configured directions. Confirm the address pins during power-up so multiple expanders receive distinct I2C addresses. Reset must not be left floating, and external devices must not contend with an SDA pin during a write. Read the manufacturer register definitions before changing polarity or direction because a configuration sequence can temporarily place a pin in an unexpected state.

Use the device within its documented 2.3 V to 5.5 V supply range and calculate the total load on VCC and the I2C pull-up network before fixing the supply budget. Port output current, input leakage, bus pull-up current, and any attached indicator loads all contribute to system power. Check the pin-level drive and sink ratings in the manufacturer datasheet, especially when a port drives LEDs or when multiple outputs are active simultaneously.

The maximum supported I2C clock frequency is 400 kHz, but the usable rate also depends on bus capacitance, pull-up strength, trace length, and the clock and data rise-time requirements. Avoid long stubs on SDA or SCL. If the expander is located near a connector or switching circuit, use series damping where necessary and verify timing with an oscilloscope at the farthest bus node.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The industrial temperature grade identifies the product's intended operating class but does not itself establish RoHS, REACH, automotive, lead-free, halogen-free, or conflict-minerals compliance.

Datos verificados el: 2026-11-14 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

PCA9538PWG4 datasheet PCA9538PWG4 pinout PCA9538PWG4 datasheet pdf PCA9538PWG4 equivalent PCA9538PWG4 replacement PCA9538PWG4 cross reference PCA9538PWG4 footprint PCA9538PWG4 schematic PCA9538PWG4 price PCA9538PWG4 stock Texas Instruments PCA9538PWG4 PCA9538 TSSOP-16 I2C expander PCA9538PWG4 vs PCA9538APW PCA9538 400 kHz GPIO expander

Componentes & términos relacionados

Texas Instruments PCA9538PWG4 PCA9538PW,118 PCA9538APW PCA9538PW NXP Semiconductors I/O expander GPIO expander interface IC semiconductor I2C SMBus I2C bus SMBus protocol digital I/O port interrupt output reset input hardware address input configuration register port register 16-pin TSSOP TSSOP package family surface mount SMD package industrial temperature grade 400 kHz bus clock
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ