PCA9555N - 16-Bit I2C GPIO Expander | NXP Semiconductors
部品番号: PCA9555N ✓ 生産中PCA9555N 概要
An I/O expander is a peripheral-controller IC that increases the number of general-purpose input/output pins available to a host microcontroller or processor. The PCA9555N belongs to the GPIO expander hierarchy, where an I2C-controlled interface manages 16 parallel digital lines while the host configures direction and reads input state through serial registers. This reduces the pin count required on processors used in compact industrial, communications, and consumer equipment.
The device divides its 16 I/O lines into two eight-bit ports and includes separate registers for input, output, polarity inversion, and configuration. Each bit can be selected independently as an input or output. The NXP product page specifically identifies higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, and small packaging as improvements over earlier family members. An interrupt output supports event-driven monitoring of input pins.
The PCA9555N uses an I2C-bus or SMBus serial interface for configuration and data transfer. Its address pins support multiple devices on the same bus, while the host reads the input register to determine the state of lines configured as inputs. The output register controls lines configured as outputs, and the polarity-inversion register allows active-high or active-low interpretation of input signals without changing external hardware.
Typical uses include expanding keypad or control-panel inputs, monitoring digital sensor and alarm lines, driving LED or relay-control inputs, supporting display and interface boards, and adding general-purpose digital I/O to compact embedded systems. The 400 kHz bus capability is useful for moderate-rate control traffic rather than high-bandwidth sensor streaming.
Designers should treat address selection, pull-up resistors, and output-pin defaults as important PCB decisions. Confirm the complete pin description in the manufacturer datasheet before assigning tracks, and validate the intended logic levels against the device’s 5 V I/O tolerance. Because the device is specified as CMOS and bus-based, correct decoupling and clean routing help preserve reliable communication.
This page combines the manufacturer’s functional description, verified source links, drop-in cross-reference findings, package-level guidance, and practical application analysis to support component selection, schematic review, and sourcing decisions for the PCA9555N.
ドロップイン代替品: PCA9555N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PCA9555N (同一形状・フットプリント).
PCA9555DB,118
✅ ドロップイン📋 参考代替品(カタログ未掲載)
PCA9555DBR
✅ ドロップイン価格はお問い合わせください
データシートを見る →PCA9555N 仕様
| Product Type | 16-bit parallel I/O expander |
| Device Architecture | CMOS interface IC |
| Number of I/O Lines | 16 bits |
| Number of Ports | 2 ports of 8 bits |
| ピン数 | 24 pins |
| パッケージ | SO24 |
| Host Interface | I2C-bus / SMBus |
| Maximum Bus Frequency | 400 kHz |
| 動作電源電圧 | 2.3 V to 5.5 V |
| I/O Tolerance | 5 V tolerant |
| Output Drive Capability | Higher drive capability |
| Input Configuration | Individual input or output selection |
| Polarity Control | Active-high or active-low input polarity inversion |
| Interrupt Support | Yes |
| Configuration Registers | 2 x 8-bit configuration registers |
| Input Register | 2 x 8-bit input registers |
| Output Register | 2 x 8-bit output registers |
| Polarity Inversion Register | 2 x 8-bit polarity inversion registers |
| 実装タイプ | Surface mount |
| RoHS ステータス | unknown |
| REACH Status | unknown |
PCA9555N ピン構成
| ピン 1 | A0 — Input address pin A0 |
| ピン 2 | A1 — Input address pin A1 |
| ピン 3 | A2 — Input address pin A2 |
| ピン 4 | P00 — Port 0 input/output line 0 |
| ピン 5 | P01 — Port 0 input/output line 1 |
| ピン 6 | P02 — Port 0 input/output line 2 |
| ピン 7 | P03 — Port 0 input/output line 3 |
| ピン 8 | GND — Ground connection |
| ピン 9 | P04 — Port 0 input/output line 4 |
| ピン 10 | P05 — Port 0 input/output line 5 |
| ピン 11 | P06 — Port 0 input/output line 6 |
| ピン 12 | P07 — Port 0 input/output line 7 |
| ピン 13 | P10 — Port 1 input/output line 0 |
| ピン 14 | P11 — Port 1 input/output line 1 |
| ピン 15 | P12 — Port 1 input/output line 2 |
| ピン 16 | P13 — Port 1 input/output line 3 |
| ピン 17 | VDD — Positive supply connection |
| ピン 18 | INT — Interrupt output |
| ピン 19 | SCL — I2C-bus clock input |
| ピン 20 | SDA — I2C-bus serial data input/output |
| ピン 21 | P14 — Port 1 input/output line 4 |
| ピン 22 | P15 — Port 1 input/output line 5 |
| ピン 23 | P16 — Port 1 input/output line 6 |
| ピン 24 | P17 — Port 1 input/output line 7 |
主な用途
PCA9555N の用途: 6 件s: Industrial Control Panel I/O Expansion, LED Status and Indicator Control, Keypad and Human-Interface Input Reading, Alarm and Sensor Monitoring Interface, Communications Equipment Status Port, Relay and Driver Control Interface.
Industrial Control Panel I/O Expansion
The PCA9555N fits compact control panels that need more digital inputs and outputs than the host controller provides. Its 16 lines can be divided into two eight-bit ports, with every bit individually selectable as input or output through dedicated configuration registers. Operators can use the lines for pushbuttons, selector switches, status indicators, and interlock signals, while the interrupt output allows the controller to respond to selected input changes. The 2.3 V to 5.5 V operating range supports common industrial logic systems, while 5 V tolerant I/O provides additional interfacing flexibility. The design should provide suitable bus pull-ups, route the interrupt as an open-drain signal where required, and verify each connected voltage against the NXP datasheet.
おすすめ
LED Status and Indicator Control
PCA9555N provides a compact way to control multiple LED status indicators from a serial bus. Each of the 16 GPIO lines can be configured independently as an output, allowing firmware to set separate visual states for power, communication, alarm, and channel indicators. The dedicated output registers let the host update one or more bits without rebuilding the complete port value in a separate external latch. Since the NXP family provides 5 V tolerant I/O and a 2.3 V to 5.5 V supply range, the device fits many 3.3 V and 5 V control boards. Designers must check the permitted output voltage and current for each line, use suitable series resistance, and account for the total load and thermal effect of simultaneously illuminated indicators.
おすすめ
Keypad and Human-Interface Input Reading
PCA9555N is useful for adding keypad rows, buttons, and rotary-switch positions to a host system without dedicating many host pins. The manufacturer datasheet describes separate configuration, input, output, and polarity-inversion registers, allowing input lines to be interpreted as active-high or active-low. An interrupt output can signal the controller when a qualifying input condition changes, supporting event-driven key detection instead of unrestricted polling. With 16 configurable I/O lines, the device can cover more interface signals than an 8-bit expander. PCB implementation should include the I2C-bus pull-up arrangement and appropriate debouncing strategy, while firmware should scan or debounce the input state before interpreting multiple simultaneous key transitions.
おすすめ
Alarm and Sensor Monitoring Interface
PCA9555N can consolidate discrete monitoring signals into a compact serial interface. Its 16 input-capable GPIO lines can monitor door sensors, fault outputs, relay contacts, comparator signals, or other digital alarm sources, while polarity inversion allows active-low fault lines to be reported consistently with active-high signals. The interrupt output allows the host to respond promptly to a changed input state, reducing the need to poll every source continuously. According to the NXP product page, the device offers individual I/O configuration, 5 V I/O tolerance, and lower supply current. Each sensor signal must remain within the specified input range, and external protection may be needed for long wiring, inductive transients, or industrial surge exposure.
おすすめ
Communications Equipment Status Port
PCA9555N is appropriate for communications equipment that needs a dedicated control and status port alongside a serial data interface. A host processor can use the 16 GPIO lines for module-reset, enable, mode-select, fault, and link-status signals while the I2C-bus carries configuration and state updates. Its 400 kHz maximum I2C-bus rate is suitable for control traffic that is intermittent rather than continuous high-bandwidth data. The two independently configurable eight-bit ports also help separate command outputs from status inputs. In a multi-board chassis, the address-selection pins should be planned so that several expanders can share the bus without address conflicts, and pull-up values should be calculated for the actual bus capacitance and voltage.
おすすめ
Relay and Driver Control Interface
PCA9555N can provide the logic-control layer for relays, latches, and discrete driver circuits. Firmware can set individual output bits to activate or deactivate a channel, while the independent configuration registers allow control outputs and status inputs to share the same 16-line device. This is particularly useful when a controller needs more channels than its available GPIO pins. Direct loads should be used only within the electrical limits stated in the NXP manufacturer datasheet; motors, solenoids, and high-current relays generally require transistor or MOSFET driver stages. Add flyback protection for inductive loads, separate return-current paths, and adequate spacing between high-energy and sensitive logic circuitry.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PCA9555N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PCA9555DB,118 | PCA9555DBR |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | Texas Instruments |
| Package | SO24 | SSOP-24 | SSOP-24 |
| Number of I/O Lines | 16 bits | 16 bits | 16 bits |
| Number of Ports | 2 x 8 bits | 2 x 8 bits | 2 x 8 bits |
| Host Interface | I2C-bus / SMBus | I2C-bus / SMBus | I2C-bus / SMBus |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
| Interrupt Support | Yes | Yes | Yes |
主な差別化要因
- Native SO24 package for the PCA9555N orderable variant (vs PCA9555DB,118)
- NXP implementation with 5 V tolerant I/O (vs PCA9555DBR)
- Individual input, output, and polarity control (vs PCA9555DB,118)
設計ノート
Assign the A0, A1, and A2 address pins before routing the I2C-bus so multiple PCA9555N devices can coexist without address conflicts. Keep SDA and SCL traces short, provide the required bus pull-ups, and route the INT output to a compatible host or interrupt controller. Confirm the exact SO24 land pattern against the NXP package drawing before releasing artwork.
Decouple the VDD pin close to the device and keep the return path to GND short. The PCA9555N supports 2.3 V to 5.5 V operation, but pull-up voltage, external signal levels, and output loads must all remain within their respective limits. Do not assume that 5 V I/O tolerance permits a 5 V pull-up when the device is operating from a lower supply; verify the bus voltage first.
Do not treat the PCA9555N as an 8-bit expander or rely only on the numeric port labels. It provides two eight-bit ports with independently configurable directions, and its polarity-inversion register affects input interpretation. Firmware should also read the input register rather than assuming an output value reflects an externally changed pin. Use the manufacturer register map to avoid confusion between configuration, output, input, and polarity addresses.
Separate high-current relay or LED drive paths from the SDA, SCL, and INT traces, especially when the PCA9555N is used only to drive transistor or MOSFET gates. Route ground returns without sharing narrow paths with switching currents. If long external lines connect to the GPIO inputs, add suitable input protection and keep the wiring away from sources of large switching transients.
コンプライアンス情報
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact PCA9555N order code.