NXP Semiconductors

PCA9555N - 16-Bit I2C GPIO Expander | NXP Semiconductors

Артикул: PCA9555N ✓ Активен
2.3 V to 5.5 V Vdss SO24 Package 400 kHz Speed
MOQ: 1 |

PCA9555N Обзор

The NXP Semiconductors PCA9555N is a 24-pin CMOS 16-bit parallel GPIO expander for I2C-bus and SMBus systems, providing individual input, output, and polarity-inversion control in an SO24 package. It supports a 2.3 V to 5.5 V operating supply range, offers 5 V I/O tolerance, and communicates at rates up to 400 kHz.

An I/O expander is a peripheral-controller IC that increases the number of general-purpose input/output pins available to a host microcontroller or processor. The PCA9555N belongs to the GPIO expander hierarchy, where an I2C-controlled interface manages 16 parallel digital lines while the host configures direction and reads input state through serial registers. This reduces the pin count required on processors used in compact industrial, communications, and consumer equipment.

The device divides its 16 I/O lines into two eight-bit ports and includes separate registers for input, output, polarity inversion, and configuration. Each bit can be selected independently as an input or output. The NXP product page specifically identifies higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, and small packaging as improvements over earlier family members. An interrupt output supports event-driven monitoring of input pins.

The PCA9555N uses an I2C-bus or SMBus serial interface for configuration and data transfer. Its address pins support multiple devices on the same bus, while the host reads the input register to determine the state of lines configured as inputs. The output register controls lines configured as outputs, and the polarity-inversion register allows active-high or active-low interpretation of input signals without changing external hardware.

Typical uses include expanding keypad or control-panel inputs, monitoring digital sensor and alarm lines, driving LED or relay-control inputs, supporting display and interface boards, and adding general-purpose digital I/O to compact embedded systems. The 400 kHz bus capability is useful for moderate-rate control traffic rather than high-bandwidth sensor streaming.

Designers should treat address selection, pull-up resistors, and output-pin defaults as important PCB decisions. Confirm the complete pin description in the manufacturer datasheet before assigning tracks, and validate the intended logic levels against the device’s 5 V I/O tolerance. Because the device is specified as CMOS and bus-based, correct decoupling and clean routing help preserve reliable communication.

This page combines the manufacturer’s functional description, verified source links, drop-in cross-reference findings, package-level guidance, and practical application analysis to support component selection, schematic review, and sourcing decisions for the PCA9555N.

Аналоги без доработки для PCA9555N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с PCA9555N (тот же форм-фактор и посадочное место).

PCA9555DB,118

✅ Прямая замена
📦 SSOP-24
Same 16-bit I2C/SMBus GPIO function and 400 kHz bus rate, but the DB,118 ordering code uses SSOP-24 rather than the PCA9555N SO24 package.

📋 Справочный аналог (нет в каталоге)

PCA9555DBR

✅ Прямая замена
NXP Semiconductors
📦 SSOP-24
16-bit I2C/SMBus GPIO expander with interrupt · 16 bits · 2.3 V to 5.5 V · 400 kHz · Two-wire serial interface · Input or output per bit · 5 V tolerant · Active-low, open-drain

Уточнить цену

Открыть даташит →

PCA9555N Характеристики

Product Type 16-bit parallel I/O expander
Device Architecture CMOS interface IC
Number of I/O Lines 16 bits
Number of Ports 2 ports of 8 bits
Число выводов 24 pins
Корпус SO24
Host Interface I2C-bus / SMBus
Maximum Bus Frequency 400 kHz
Рабочее напряжение питания 2.3 V to 5.5 V
I/O Tolerance 5 V tolerant
Output Drive Capability Higher drive capability
Input Configuration Individual input or output selection
Polarity Control Active-high or active-low input polarity inversion
Interrupt Support Yes
Configuration Registers 2 x 8-bit configuration registers
Input Register 2 x 8-bit input registers
Output Register 2 x 8-bit output registers
Polarity Inversion Register 2 x 8-bit polarity inversion registers
Тип монтажа Surface mount
Статус RoHS unknown
REACH Status unknown

Конфигурация выводов PCA9555N

Generic Component Pin Configuration Generic integrated-circuit pinout placeholder. Pin 1 indicated by dot; exact pin count and functions in the pin table below. 1 N 2 N-1 3 N-2 4 N-3 Pin Configuration See pin table below for pin functions Package-specific diagram not available
Контакт 1 A0 — Input address pin A0
Контакт 2 A1 — Input address pin A1
Контакт 3 A2 — Input address pin A2
Контакт 4 P00 — Port 0 input/output line 0
Контакт 5 P01 — Port 0 input/output line 1
Контакт 6 P02 — Port 0 input/output line 2
Контакт 7 P03 — Port 0 input/output line 3
Контакт 8 GND — Ground connection
Контакт 9 P04 — Port 0 input/output line 4
Контакт 10 P05 — Port 0 input/output line 5
Контакт 11 P06 — Port 0 input/output line 6
Контакт 12 P07 — Port 0 input/output line 7
Контакт 13 P10 — Port 1 input/output line 0
Контакт 14 P11 — Port 1 input/output line 1
Контакт 15 P12 — Port 1 input/output line 2
Контакт 16 P13 — Port 1 input/output line 3
Контакт 17 VDD — Positive supply connection
Контакт 18 INT — Interrupt output
Контакт 19 SCL — I2C-bus clock input
Контакт 20 SDA — I2C-bus serial data input/output
Контакт 21 P14 — Port 1 input/output line 4
Контакт 22 P15 — Port 1 input/output line 5
Контакт 23 P16 — Port 1 input/output line 6
Контакт 24 P17 — Port 1 input/output line 7

Типичное применение

PCA9555N подходит для 6 применениеs: Industrial Control Panel I/O Expansion, LED Status and Indicator Control, Keypad and Human-Interface Input Reading, Alarm and Sensor Monitoring Interface, Communications Equipment Status Port, Relay and Driver Control Interface.

🏭

Industrial Control Panel I/O Expansion

The PCA9555N fits compact control panels that need more digital inputs and outputs than the host controller provides. Its 16 lines can be divided into two eight-bit ports, with every bit individually selectable as input or output through dedicated configuration registers. Operators can use the lines for pushbuttons, selector switches, status indicators, and interlock signals, while the interrupt output allows the controller to respond to selected input changes. The 2.3 V to 5.5 V operating range supports common industrial logic systems, while 5 V tolerant I/O provides additional interfacing flexibility. The design should provide suitable bus pull-ups, route the interrupt as an open-drain signal where required, and verify each connected voltage against the NXP datasheet.

💡

LED Status and Indicator Control

PCA9555N provides a compact way to control multiple LED status indicators from a serial bus. Each of the 16 GPIO lines can be configured independently as an output, allowing firmware to set separate visual states for power, communication, alarm, and channel indicators. The dedicated output registers let the host update one or more bits without rebuilding the complete port value in a separate external latch. Since the NXP family provides 5 V tolerant I/O and a 2.3 V to 5.5 V supply range, the device fits many 3.3 V and 5 V control boards. Designers must check the permitted output voltage and current for each line, use suitable series resistance, and account for the total load and thermal effect of simultaneously illuminated indicators.

🔧

Keypad and Human-Interface Input Reading

PCA9555N is useful for adding keypad rows, buttons, and rotary-switch positions to a host system without dedicating many host pins. The manufacturer datasheet describes separate configuration, input, output, and polarity-inversion registers, allowing input lines to be interpreted as active-high or active-low. An interrupt output can signal the controller when a qualifying input condition changes, supporting event-driven key detection instead of unrestricted polling. With 16 configurable I/O lines, the device can cover more interface signals than an 8-bit expander. PCB implementation should include the I2C-bus pull-up arrangement and appropriate debouncing strategy, while firmware should scan or debounce the input state before interpreting multiple simultaneous key transitions.

🧩

Alarm and Sensor Monitoring Interface

PCA9555N can consolidate discrete monitoring signals into a compact serial interface. Its 16 input-capable GPIO lines can monitor door sensors, fault outputs, relay contacts, comparator signals, or other digital alarm sources, while polarity inversion allows active-low fault lines to be reported consistently with active-high signals. The interrupt output allows the host to respond promptly to a changed input state, reducing the need to poll every source continuously. According to the NXP product page, the device offers individual I/O configuration, 5 V I/O tolerance, and lower supply current. Each sensor signal must remain within the specified input range, and external protection may be needed for long wiring, inductive transients, or industrial surge exposure.

🌐

Communications Equipment Status Port

PCA9555N is appropriate for communications equipment that needs a dedicated control and status port alongside a serial data interface. A host processor can use the 16 GPIO lines for module-reset, enable, mode-select, fault, and link-status signals while the I2C-bus carries configuration and state updates. Its 400 kHz maximum I2C-bus rate is suitable for control traffic that is intermittent rather than continuous high-bandwidth data. The two independently configurable eight-bit ports also help separate command outputs from status inputs. In a multi-board chassis, the address-selection pins should be planned so that several expanders can share the bus without address conflicts, and pull-up values should be calculated for the actual bus capacitance and voltage.

⚡

Relay and Driver Control Interface

PCA9555N can provide the logic-control layer for relays, latches, and discrete driver circuits. Firmware can set individual output bits to activate or deactivate a channel, while the independent configuration registers allow control outputs and status inputs to share the same 16-line device. This is particularly useful when a controller needs more channels than its available GPIO pins. Direct loads should be used only within the electrical limits stated in the NXP manufacturer datasheet; motors, solenoids, and high-current relays generally require transistor or MOSFET driver stages. Add flyback protection for inductive loads, separate return-current paths, and adequate spacing between high-energy and sensitive logic circuitry.

What are the key specifications of PCA9555N that engineers should know?
The PCA9555N is a 24-pin CMOS device that expands a serial I2C or SMBus connection into 16 independently configurable GPIO lines. According to the NXP product page and manufacturer datasheet, it supports a 2.3 V to 5.5 V operating range, 5 V tolerant I/O, a bus rate up to 400 kHz, separate input and output registers, polarity inversion, and an interrupt output. Its two eight-bit ports make it suitable for compact systems that need additional digital lines without assigning 16 dedicated host-controller pins.
Where can I download the PCA9555N datasheet PDF?
The PCA9555N datasheet PDF is available from NXP Semiconductors at https://www.nxp.com/docs/en/data-sheet/PCA9555.pdf. The document is the appropriate source for the complete 24-pin description, register map, electrical characteristics, timing information, address selection, and application guidance. A separate NXP product page also provides a concise functional summary, while the PCA9555 family PDF may cover related package options.
Where can I find the PCA9555N pinout?
The PCA9555N pinout is defined by the NXP manufacturer datasheet at https://www.nxp.com/docs/en/data-sheet/PCA9555.pdf. The device has 24 pins in an SO24 package and includes supply, ground, I2C-bus, interrupt, address-selection, and port I/O connections. Use the pin-description table in the datasheet when assigning PCB tracks, especially because the address pins and the two eight-bit ports determine the device address and external signal mapping.
How does the PCA9555N configure its 16 GPIO lines?
The PCA9555N configures each of its 16 GPIO lines independently as an input or output through two eight-bit configuration registers. According to the NXP manufacturer datasheet, the input register reflects the state of input-configured pins, the output register controls output-configured pins, and the polarity-inversion register selects active-high or active-low input interpretation. The I2C-bus or SMBus host writes these registers and reads the input state serially.
What is the PCA9555N power-supply voltage range?
The PCA9555N operates from 2.3 V to 5.5 V and includes 5 V tolerant I/O. The NXP product page identifies lower supply current and 5 V I/O tolerance among the family’s key features. The supply range allows the same device family to be used in 3.3 V and 5 V embedded systems, but external pull-ups and connected logic levels must be selected for the actual bus and I/O voltages.
How fast is the PCA9555N I2C-bus interface?
The PCA9555N supports I2C-bus and SMBus communication at up to 400 kHz. The manufacturer datasheet describes the device as a 16-bit parallel GPIO expander whose configuration, input, output, and polarity data are accessed through serial registers. This rate is appropriate for control and status traffic involving keys, indicators, and discrete digital signals, rather than continuous high-volume data transfer.
What can replace the PCA9555N?
The PCA9555N can be replaced only when the candidate has the same SO24 footprint, matching pin functions, and compatible electrical behavior. The MaxLinear cross-reference identifies XRA1201PIG24TR-F as pin- and software-compatible, but its PIG24 designation denotes a through-hole DIP-24 package rather than the PCA9555N’s surface-mount SO24 package. It is therefore not a board-level drop-in replacement for PCA9555N without PCB changes.
Is the XRA1201PIG24TR-F a drop-in replacement for PCA9555N?
The XRA1201PIG24TR-F is not a true drop-in replacement for PCA9555N on an existing surface-mount board. The MaxLinear cross-reference calls it pin- and software-compatible and notes different operating-voltage ranges, but XRA1201PIG24TR-F uses a PIG24 through-hole package while PCA9555N is an SO24 surface-mount device. Engineers must also verify its supply range and I/O levels before using it on a redesigned board.
What is the best drop-in replacement for PCA9555N?
The best drop-in replacement is a device offered in the identical SO24 package with the same 24-pin assignments, 16-bit I/O organization, address-selection method, interrupt behavior, and compatible 2.3 V to 5.5 V electrical range. The available cross-reference confirms pin and software compatibility for XRA1201PIG24TR-F, but its DIP-24 package prevents direct substitution on PCA9555N footprints. No verified SO24 substitute was identified, so the NXP device should remain the primary choice.
When should I choose PCA9555N over another 16-bit I/O expander?
Choose PCA9555N when the design specifically uses its SO24 footprint and requires 16 separately configurable I/O lines with interrupt support, input polarity inversion, and operation from 2.3 V to 5.5 V. Select another device only after verifying package geometry, pin names, address pins, register behavior, bus timing, and logic-level compatibility. A similar GPIO count alone does not establish drop-in compatibility.
Is PCA9555N suitable for industrial control and automation systems?
PCA9555N is suitable for many industrial control, automation, and communications boards where a host processor needs additional discrete digital I/O. Its 16 individually configurable lines can monitor switches or sensors and control LEDs or external interface signals, while the interrupt output permits event-driven host processing. The NXP datasheet supports this use through dedicated direction, input, output, and polarity registers, but the system must still meet its voltage and timing limits.
How should PCA9555N be used for LED and relay-control outputs?
PCA9555N can control LED indicators or logic inputs to relay drivers by programming individual output bits through the output register. According to the NXP manufacturer datasheet, each line has an independently selected output configuration, allowing unrelated loads to share the device. Check continuous output current, voltage, and drive limits in the electrical characteristics before connecting a load; add suitable transistor or driver circuitry when the load exceeds the GPIO’s direct drive capability.
Can PCA9555N read active-low keypad or switch signals?
Yes, PCA9555N can read active-low keypad or switch signals and can invert their interpreted polarity without external inversion logic. The NXP manufacturer datasheet describes polarity-inversion registers covering the input lines, while the configuration registers select each line as input or output. The interrupt output can notify the host when an input state changes, reducing the need for continuous polling in suitably designed systems.
Where can I buy PCA9555N online and what is its current price?
Use the Request a Quote form on this page to ask about PCA9555N availability, price, quantity, and lead time. The form provides a direct route for an exact-order inquiry covering the NXP Semiconductors PCA9555N in its SO24 package. Current commercial terms can change with quantity and supply, so obtaining a quote for the intended order quantity is more reliable than relying on a static historical listing.
What is the lead time for PCA9555N?
Request the current PCA9555N lead time through the Request a Quote form on this page. Lead time depends on the required quantity, package, production schedule, and market availability. The NXP product page presents the PCA9555 family as a current product offering, but a firm delivery commitment should be confirmed for the exact order rather than inferred from general family availability.
Is PCA9555N currently active and available for design-in?
The NXP Semiconductors product page lists the PCA9555 family as an active general-purpose I/O expander, and the family documentation remains available from the manufacturer. The PCA9555N is the SO24 orderable variant of that 16-bit device. Use the Request a Quote form on this page to confirm current stock, minimum order quantity, and production lead time for a specific procurement volume.

Справочные инженерные данные для PCA9555N — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose PCA9555N when the PCB footprint is specifically SO24 and the design needs 16 independently configurable digital lines through an I2C-bus or SMBus interface. Its 2.3 V to 5.5 V operating range, 5 V tolerant I/O, input polarity inversion, and interrupt output are useful in compact control, monitoring, keypad, and communications systems. Choose PCA9555DB,118 when an NXP-sourced SSOP-24 layout is acceptable, or PCA9555DBR when its documented weak-pull-up feature is desired. Do not substitute either listed family alternative on an existing PCA9555N board because the package differs. XRA1201PIG24TR-F offers pin and software compatibility according to the cross-reference, but its DIP-24 package requires a PCB redesign and its operating-voltage range must be checked. For a no-change replacement, retain PCA9555N or qualify another specifically documented SO24, 24-pin equivalent.

Сравнение с аналогами

Параметр Этот товар PCA9555DB,118 PCA9555DBR
Brand NXP Semiconductors NXP Semiconductors Texas Instruments
Package SO24 SSOP-24 SSOP-24
Number of I/O Lines 16 bits 16 bits 16 bits
Number of Ports 2 x 8 bits 2 x 8 bits 2 x 8 bits
Host Interface I2C-bus / SMBus I2C-bus / SMBus I2C-bus / SMBus
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz
Interrupt Support Yes Yes Yes

Ключевые отличия

  • Native SO24 package for the PCA9555N orderable variant (против PCA9555DB,118)
  • NXP implementation with 5 V tolerant I/O (против PCA9555DBR)
  • Individual input, output, and polarity control (против PCA9555DB,118)

Заметки по проектированию

Assign the A0, A1, and A2 address pins before routing the I2C-bus so multiple PCA9555N devices can coexist without address conflicts. Keep SDA and SCL traces short, provide the required bus pull-ups, and route the INT output to a compatible host or interrupt controller. Confirm the exact SO24 land pattern against the NXP package drawing before releasing artwork.

Decouple the VDD pin close to the device and keep the return path to GND short. The PCA9555N supports 2.3 V to 5.5 V operation, but pull-up voltage, external signal levels, and output loads must all remain within their respective limits. Do not assume that 5 V I/O tolerance permits a 5 V pull-up when the device is operating from a lower supply; verify the bus voltage first.

Do not treat the PCA9555N as an 8-bit expander or rely only on the numeric port labels. It provides two eight-bit ports with independently configurable directions, and its polarity-inversion register affects input interpretation. Firmware should also read the input register rather than assuming an output value reflects an externally changed pin. Use the manufacturer register map to avoid confusion between configuration, output, input, and polarity addresses.

Separate high-current relay or LED drive paths from the SDA, SCL, and INT traces, especially when the PCA9555N is used only to drive transistor or MOSFET gates. Route ground returns without sharing narrow paths with switching currents. If long external lines connect to the GPIO inputs, add suitable input protection and keep the wiring away from sources of large switching transients.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact PCA9555N order code.

Похожие запросы

pca9555 nxp pca9555 datasheet pca9555 pdf pca9555 spec pca9555 dts pca9555 verilog pca9555 evaluation board PCA9555N pinout PCA9555N SO24 footprint PCA9555N equivalent PCA9555N replacement PCA9555N vs PCA9555DBR PCA9555N price PCA9555N stock

Связанные компоненты & термины

NXP Semiconductors PCA9555N PCA9555DB,118 PCA9555DBR PCA9555 16-bit GPIO expander I/O expander parallel I/O I2C-bus SMBus CMOS general-purpose input/output GPIO interrupt output input register output register polarity inversion configuration register SO24 surface mount 5 V tolerant I/O 2.3 V to 5.5 V 400 kHz industrial control communications equipment
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ