PCA9674D - 8-Bit 1MHz I/O Expander | NXP Semiconductors
部品番号: PCA9674D ✗ 生産終了PCA9674D 概要
An I/O expander is an interface IC that adds digital input and output ports through a serial bus. In the product hierarchy, the PCA9674D is an I/O expander within the interface IC category and a peripheral for microcontrollers and other I2C hosts. The host controller uses SCL and SDA to configure the ports, read inputs, change output states, and receive an interrupt when an input condition is detected.
The PCA9674D provides eight quasi-bidirectional ports, a 1 MHz I2C bus, three hardware-selectable address inputs, and an interrupt output. Its eight ports can be individually configured as inputs or outputs through the device registers. Quasi-bidirectional ports include an internal pull-up arrangement and can support LED dimming through PWM-compatible output control. The I2C interface also allows multiple expanders to share one bus through address selection.
The device supports up to 64 hardware-selectable addresses because A0, A1, and A2 provide three binary address inputs. This enables a bus to connect many remote I/O ports without requiring a separate microcontroller pin for each device. The PCA9674D and PCA9674A use non-overlapping slave-address ranges, allowing both families to operate together on the same I2C bus for further expansion.
Typical uses include reading switches and push buttons, driving LEDs, controlling solenoid or relay interfaces, monitoring digital sensors, and adding GPIO capacity to industrial controllers. The 1 MHz bus rate also makes the device suitable for LED backlight control and other applications where the host must update multiple output states efficiently.
PCB design should place the I2C pull-up resistors and bypass capacitor close to the appropriate supply and bus pins. Account for address selection before fixing the PCB, because the A0, A1, and A2 levels determine the slave address. Confirm that downstream devices remain compatible with the quasi-bidirectional port behavior before using an output pin as a strong source for a high-current load.
This product page consolidates the electrical limits, package details, lifecycle information, pin assignments, sourcing guidance, and verified drop-in alternatives into one engineering reference. It also highlights the boundary between a true pin-compatible replacement and a functionally similar GPIO expander that requires a different footprint or interface arrangement.
ドロップイン代替品: PCA9674D — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
PCA9674AD,512
✅ ドロップイン📋 参考代替品(カタログ未掲載)
PCA9674AD,518
✅ ドロップイン📋 参考代替品(カタログ未掲載)
PCA9674D 仕様
| Device Type | Remote 8-bit I/O expander |
| Number of I/O Ports | 8 ports |
| Serial Interface | I2C-bus |
| I2C Maximum Clock Frequency | 1 MHz |
| 動作電源電圧 | 2.3 V to 5.5 V |
| Address Input Pins | 3 hardware-selectable inputs |
| Number of Hardware-Selectable Addresses | 64 addresses |
| Interrupt Output | 1 open-drain interrupt output |
| Port Type | Quasi-bidirectional |
| パッケージ | 16-pin SOIC, 7.50 mm width |
| 実装タイプ | Surface mount |
| Tube Packaging Variant | PCA9674D,512 |
| Tape-and-Reel Packaging Variant | PCA9674D,518 |
| Functional Description | Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt |
PCA9674D ピン構成
| ピン 1 | A0 — Slave-address input 0 |
| ピン 2 | A1 — Slave-address input 1 |
| ピン 3 | A2 — Slave-address input 2 |
| ピン 4 | SCL — I2C serial clock input |
| ピン 5 | SDA — I2C serial data input and output |
| ピン 6 | INT — Interrupt output |
| ピン 7 | VSS — Ground connection |
| ピン 8 | P0 — Quasi-bidirectional I/O port 0 |
| ピン 9 | P1 — Quasi-bidirectional I/O port 1 |
| ピン 10 | P2 — Quasi-bidirectional I/O port 2 |
| ピン 11 | P3 — Quasi-bidirectional I/O port 3 |
| ピン 12 | P4 — Quasi-bidirectional I/O port 4 |
| ピン 13 | P5 — Quasi-bidirectional I/O port 5 |
| ピン 14 | P6 — Quasi-bidirectional I/O port 6 |
| ピン 15 | P7 — Quasi-bidirectional I/O port 7 |
| ピン 16 | VDD — Positive supply voltage |
主な用途
PCA9674D の用途: 6 件s: Industrial Switch and Relay Control, LED Backlight and Status Control, Smart Home Sensor Aggregation, Programmable Logic Controller I/O, Audio and Communication Equipment Control, LED Matrix and Display Control.
Industrial Switch and Relay Control
The PCA9674D is useful in industrial controllers that need more digital I/O than the host microcontroller directly exposes. Its eight quasi-bidirectional ports can read limit switches, door sensors, or push buttons and can command relay-driver inputs, status indicators, and other digital loads through the 1 MHz I2C-bus. Three address inputs permit up to 64 PCA9674 devices on one bus, reducing wiring and host-pin pressure in a multi-panel system. A practical design uses the interrupt output to wake the controller when an input changes, while transistor or MOSFET driver stages should handle relays and inductive loads rather than driving them directly from port pins.
おすすめ
LED Backlight and Status Control
The PCA9674D can add organized LED control to a display or control panel without consuming eight dedicated GPIO pins on the host. Its eight ports are individually addressable through the I2C register interface, and PWM-capable operation can support dimming when the host applies the appropriate pulse patterns. A 1 MHz bus supports rapid updates across multiple indicator or backlight groups. The 2.3 V to 5.5 V operating range also permits use in both 3.3 V and 5 V systems. Keep trace current within the port limits and place the device near the LED-driver circuitry to minimize switching-related coupling on sensitive analog sections.
おすすめ
Smart Home Sensor Aggregation
The PCA9674D can serve as a compact remote I/O hub in a smart-home controller where door contacts, occupancy sensors, alarm outputs, and indicator LEDs exceed the available host pins. Eight ports provide individually configurable digital channels, while the interrupt line lets the host respond only when a monitored input changes. The I2C Fast-mode Plus interface operates up to 1 MHz and the address pins allow multiple hubs to share one bus. The device's 2.3 V minimum supply supports low-voltage systems, although the designer should verify downstream sensor logic levels and include appropriate pull-ups for the shared bus.
おすすめ
Programmable Logic Controller I/O
The PCA9674D is appropriate for compact PLC and embedded automation modules that require distributed digital inputs and outputs. A host processor can configure all eight ports through the I2C interface and use hardware address selection to support multiple expansion modules. Inputs may monitor interlocks or push buttons, while outputs can drive logic-level indicators or gate external transistor drivers. The interrupt output helps reduce polling overhead by signaling the controller after an input event. Because the ports are quasi-bidirectional rather than general-purpose push-pull outputs, every connected circuit should be checked for compatibility with the port's internal pull-up behavior and electrical loading.
おすすめ
Audio and Communication Equipment Control
The PCA9674D can extend control and status lines in audio receivers, communication equipment, and other mixed-signal products. Eight ports can operate mute indicators, amplifier-enable signals, relay-select controls, front-panel buttons, or digital status inputs while the host uses the I2C bus for configuration. The 1 MHz interface permits quick register updates during system control sequences, and the interrupt output supports efficient response to user-panel activity. Its 16-pin SOIC package simplifies upgrade paths on boards that already use that footprint. The I2C pull-ups should be sized for the complete bus, and the device should be positioned away from high-current switching stages to minimize coupling.
おすすめ
LED Matrix and Display Control
The PCA9674D can support segmented LED matrices, signage, or multi-zone lighting systems where several independent digital outputs would otherwise occupy most of a host controller's pins. Addressable port registers allow the controller to update illumination patterns quickly over the 1 MHz I2C-bus, while PWM-capable control can create variable brightness effects. Three hardware address inputs permit multiple expander channels on one bus and simplify scalable display arrangements. The 16-pin SOIC package provides a straightforward route for board population and rework. Designers should account for driver-transistor topology, refresh timing, and ground-return paths because the PCA9674D controls logic signals rather than directly powering high-current LED strings.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PCA9674D — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PCA9674AD,512 | PCA9674AD,518 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same |
| Device Function | Remote 8-bit I/O expander | Remote 8-bit I/O expander | Remote 8-bit I/O expander |
| I/O Port Count | 8 | 8 | 8 |
| I2C Clock Frequency | 1 MHz | 1 MHz | 1 MHz |
| Supply Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Slave Address Family | PCA9674 address range | PCA9674A address range | PCA9674A address range |
| Interrupt Output | Yes | Yes | Yes |
| Hardware Address Inputs | 3 | 3 | 3 |
| Order Form | PCA9674D | Tube order form | Tape-and-reel order form |
主な差別化要因
- Direct address-range transition within the same device family (vs PCA9674AD,512)
- Production packaging flexibility for the same 16-SOIC design (vs PCA9674AD,518)
- Higher bus rate than standard 100 kHz I2C designs (vs PCA9674AD,512)
設計ノート
Use the 16-pin SOIC footprint associated with the NXP package drawing and verify pin 1 orientation against the PCB silkscreen. Place the device near the connector or controlled peripheral group it serves to keep the eight port traces short. Route SCL and SDA away from inductive or high-current switching paths, and provide the supply bypass capacitor close to VDD with a short ground return to VSS.
Do not assume that a PCA9674A can use the original PCA9674 slave address. The NXP datasheet states that the devices are identical except for their non-overlapping slave addresses. Update firmware and verify that no other device already occupies the new address. Also avoid using a quasi-bidirectional port as a push-pull output driver for loads requiring a guaranteed low output resistance.
Estimate the total I2C pull-up current before selecting resistor values, including the current required by every device on the bus. The bus must remain within the electrical limits of the host and all expanders, and the pull-up voltage must match the bus logic level. Add local supply decoupling at the PCA9674D and avoid routing the interrupt trace beside noisy power stages when a sensitive host input is connected.
Assign the A0, A1, and A2 levels during hardware planning because they determine the device's slave address. Tie the address pins only to the levels allowed by the NXP datasheet and make the routing easy to inspect during production review. For LED matrices or multichannel panels, keep port-to-driver paths short and provide a quiet return path so switching currents do not share sensitive signal ground routes.
コンプライアンス情報
The NXP product information identifies PCA9674D as no longer manufactured. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated on the accessed product pages.