最後購買通知: PCA9674D 即將停產。最後下單日期: 聯絡我們. 查看可用的替代零件 →
NXP Semiconductors

PCA9674D - 8-Bit 1MHz I/O Expander | NXP Semiconductors

MPN: PCA9674D ✗ 停產
2.3 V to 5.5 V Vdss 16-pin SOIC, 7.50 mm width Package 1 MHz Speed
MOQ: 1 |

PCA9674D 概覽

The NXP Semiconductors PCA9674D is an 8-bit remote I/O expander with a 1 MHz I2C Fast-mode Plus interface, eight quasi-bidirectional GPIO ports, and an interrupt output, supplied in a 16-pin SOIC package. Its operating supply range is 2.3 V to 5.5 V, making it suitable for low-voltage embedded systems and conventional 5 V industrial interfaces.

An I/O expander is an interface IC that adds digital input and output ports through a serial bus. In the product hierarchy, the PCA9674D is an I/O expander within the interface IC category and a peripheral for microcontrollers and other I2C hosts. The host controller uses SCL and SDA to configure the ports, read inputs, change output states, and receive an interrupt when an input condition is detected.

The PCA9674D provides eight quasi-bidirectional ports, a 1 MHz I2C bus, three hardware-selectable address inputs, and an interrupt output. Its eight ports can be individually configured as inputs or outputs through the device registers. Quasi-bidirectional ports include an internal pull-up arrangement and can support LED dimming through PWM-compatible output control. The I2C interface also allows multiple expanders to share one bus through address selection.

The device supports up to 64 hardware-selectable addresses because A0, A1, and A2 provide three binary address inputs. This enables a bus to connect many remote I/O ports without requiring a separate microcontroller pin for each device. The PCA9674D and PCA9674A use non-overlapping slave-address ranges, allowing both families to operate together on the same I2C bus for further expansion.

Typical uses include reading switches and push buttons, driving LEDs, controlling solenoid or relay interfaces, monitoring digital sensors, and adding GPIO capacity to industrial controllers. The 1 MHz bus rate also makes the device suitable for LED backlight control and other applications where the host must update multiple output states efficiently.

PCB design should place the I2C pull-up resistors and bypass capacitor close to the appropriate supply and bus pins. Account for address selection before fixing the PCB, because the A0, A1, and A2 levels determine the slave address. Confirm that downstream devices remain compatible with the quasi-bidirectional port behavior before using an output pin as a strong source for a high-current load.

This product page consolidates the electrical limits, package details, lifecycle information, pin assignments, sourcing guidance, and verified drop-in alternatives into one engineering reference. It also highlights the boundary between a true pin-compatible replacement and a functionally similar GPIO expander that requires a different footprint or interface arrangement.

直接替換替代品,適用於 PCA9674D — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

PCA9674AD,512

✅ 直接替換
📦 16-SOIC
Slave address differs from PCA9674D,512 while the 16-pin terminal arrangement, 1 MHz I2C interface, and eight-port function remain the same; firmware requires an address update.

📋 參考替代品(不在目錄中)

PCA9674AD,518

✅ 直接替換
📦 16-SOIC
Slave address differs from PCA9674D,518 and the order form changes to tape-and-reel; electrical function, 16-SOIC footprint, eight ports, and 1 MHz I2C interface remain equivalent.

📋 參考替代品(不在目錄中)

PCA9674D 規格

Device Type Remote 8-bit I/O expander
Number of I/O Ports 8 ports
Serial Interface I2C-bus
I2C Maximum Clock Frequency 1 MHz
工作電源電壓 2.3 V to 5.5 V
Address Input Pins 3 hardware-selectable inputs
Number of Hardware-Selectable Addresses 64 addresses
Interrupt Output 1 open-drain interrupt output
Port Type Quasi-bidirectional
封裝 16-pin SOIC, 7.50 mm width
安裝類型 Surface mount
Tube Packaging Variant PCA9674D,512
Tape-and-Reel Packaging Variant PCA9674D,518
Functional Description Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt

PCA9674D 腳位配置

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
腳位 1 A0 — Slave-address input 0
腳位 2 A1 — Slave-address input 1
腳位 3 A2 — Slave-address input 2
腳位 4 SCL — I2C serial clock input
腳位 5 SDA — I2C serial data input and output
腳位 6 INT — Interrupt output
腳位 7 VSS — Ground connection
腳位 8 P0 — Quasi-bidirectional I/O port 0
腳位 9 P1 — Quasi-bidirectional I/O port 1
腳位 10 P2 — Quasi-bidirectional I/O port 2
腳位 11 P3 — Quasi-bidirectional I/O port 3
腳位 12 P4 — Quasi-bidirectional I/O port 4
腳位 13 P5 — Quasi-bidirectional I/O port 5
腳位 14 P6 — Quasi-bidirectional I/O port 6
腳位 15 P7 — Quasi-bidirectional I/O port 7
腳位 16 VDD — Positive supply voltage

典型應用

PCA9674D 適用於 6 應用s: Industrial Switch and Relay Control, LED Backlight and Status Control, Smart Home Sensor Aggregation, Programmable Logic Controller I/O, Audio and Communication Equipment Control, LED Matrix and Display Control.

🏭

Industrial Switch and Relay Control

The PCA9674D is useful in industrial controllers that need more digital I/O than the host microcontroller directly exposes. Its eight quasi-bidirectional ports can read limit switches, door sensors, or push buttons and can command relay-driver inputs, status indicators, and other digital loads through the 1 MHz I2C-bus. Three address inputs permit up to 64 PCA9674 devices on one bus, reducing wiring and host-pin pressure in a multi-panel system. A practical design uses the interrupt output to wake the controller when an input changes, while transistor or MOSFET driver stages should handle relays and inductive loads rather than driving them directly from port pins.

💡

LED Backlight and Status Control

The PCA9674D can add organized LED control to a display or control panel without consuming eight dedicated GPIO pins on the host. Its eight ports are individually addressable through the I2C register interface, and PWM-capable operation can support dimming when the host applies the appropriate pulse patterns. A 1 MHz bus supports rapid updates across multiple indicator or backlight groups. The 2.3 V to 5.5 V operating range also permits use in both 3.3 V and 5 V systems. Keep trace current within the port limits and place the device near the LED-driver circuitry to minimize switching-related coupling on sensitive analog sections.

🧩

Smart Home Sensor Aggregation

The PCA9674D can serve as a compact remote I/O hub in a smart-home controller where door contacts, occupancy sensors, alarm outputs, and indicator LEDs exceed the available host pins. Eight ports provide individually configurable digital channels, while the interrupt line lets the host respond only when a monitored input changes. The I2C Fast-mode Plus interface operates up to 1 MHz and the address pins allow multiple hubs to share one bus. The device's 2.3 V minimum supply supports low-voltage systems, although the designer should verify downstream sensor logic levels and include appropriate pull-ups for the shared bus.

🔧

Programmable Logic Controller I/O

The PCA9674D is appropriate for compact PLC and embedded automation modules that require distributed digital inputs and outputs. A host processor can configure all eight ports through the I2C interface and use hardware address selection to support multiple expansion modules. Inputs may monitor interlocks or push buttons, while outputs can drive logic-level indicators or gate external transistor drivers. The interrupt output helps reduce polling overhead by signaling the controller after an input event. Because the ports are quasi-bidirectional rather than general-purpose push-pull outputs, every connected circuit should be checked for compatibility with the port's internal pull-up behavior and electrical loading.

🎧

Audio and Communication Equipment Control

The PCA9674D can extend control and status lines in audio receivers, communication equipment, and other mixed-signal products. Eight ports can operate mute indicators, amplifier-enable signals, relay-select controls, front-panel buttons, or digital status inputs while the host uses the I2C bus for configuration. The 1 MHz interface permits quick register updates during system control sequences, and the interrupt output supports efficient response to user-panel activity. Its 16-pin SOIC package simplifies upgrade paths on boards that already use that footprint. The I2C pull-ups should be sized for the complete bus, and the device should be positioned away from high-current switching stages to minimize coupling.

📺

LED Matrix and Display Control

The PCA9674D can support segmented LED matrices, signage, or multi-zone lighting systems where several independent digital outputs would otherwise occupy most of a host controller's pins. Addressable port registers allow the controller to update illumination patterns quickly over the 1 MHz I2C-bus, while PWM-capable control can create variable brightness effects. Three hardware address inputs permit multiple expander channels on one bus and simplify scalable display arrangements. The 16-pin SOIC package provides a straightforward route for board population and rework. Designers should account for driver-transistor topology, refresh timing, and ground-return paths because the PCA9674D controls logic signals rather than directly powering high-current LED strings.

What is the PCA9674D?
The PCA9674D is an 8-bit remote I/O expander that communicates through a 1 MHz I2C-bus and includes an interrupt output. It provides eight quasi-bidirectional ports for digital inputs and outputs, operates from 2.3 V to 5.5 V, and is packaged in a 16-pin SOIC. According to the NXP PCA9674 and PCA9674A datasheet, it is designed to add GPIO capacity to microcontroller-based systems.
What is the operating voltage of PCA9674D?
The PCA9674D operates from 2.3 V to 5.5 V. This range allows the same device to interface with 3.3 V embedded systems and 5 V control equipment. The NXP product information identifies the device as an 8-bit I2C Fast-mode Plus expander, while the device datasheet defines the detailed input-voltage limits, output behavior, and electrical characteristics.
How many GPIO pins does the PCA9674D provide?
The PCA9674D provides eight quasi-bidirectional I/O ports, designated P0 through P7. Each port can be configured as an input or output through the internal registers. The NXP datasheet describes the PCA9674 as a general-purpose remote I/O expander intended to reduce the number of host-controller pins required for switches, indicators, and other digital peripherals.
Where can I download the PCA9674D datasheet PDF?
The official PCA9674D datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9674_PCA9674A.pdf. This document covers the PCA9674 and PCA9674A families, including the 16-pin package, pin descriptions, register map, electrical characteristics, address selection, and application information. Use the manufacturer's document when assigning PCB pins or checking operating limits.
Where is the PCA9674D pinout located?
The PCA9674D pinout is shown in the NXP PCA9674 and PCA9674A datasheet. The 16-pin SOIC uses A0, A1, and A2 on pins 1 through 3, SCL on pin 4, SDA on pin 5, INT on pin 6, VSS on pin 7, P0 through P7 on pins 8 through 15, and VDD on pin 16. Follow the package drawing and pin-description table when creating the PCB footprint.
What is the best drop-in replacement for PCA9674D?
The PCA9674AD,512 is the closest documented drop-in choice because its terminals and package match PCA9674D,512 and the comparison identifies it as directly replaceable without circuit modification. Its slave address is different, so firmware must select the corresponding address. The NXP datasheet states that PCA9674 and PCA9674A are identical except for their non-overlapping slave-address assignments.
Can PCA9674A replace PCA9674D?
Yes, a PCA9674A can replace a PCA9674D when the board footprint and electrical interface remain unchanged, but the firmware address must be updated. The NXP datasheet states that the two devices are identical except for different, non-overlapping slave addresses. Because the address pins are hardware-selected, changing between families does not provide the same address on the same bus.
What can replace PCA9674D?
The PCA9674A-family devices are the most direct replacements because they retain the remote 8-bit I/O-expander function and use the same 16-pin SOIC arrangement. The PCA9674AD,512 is a documented direct replacement for PCA9674D,512, while the PCA9674AD,518 offers the corresponding tape-and-reel order form. Review the slave address and update firmware before substituting any family variant.
PCA9674D vs PCA9674AD,512 - which is better?
The PCA9674D is preferable when existing firmware and board documentation are tied to its slave address, while the PCA9674AD,512 is a practical drop-in choice when the original is no longer manufactured. Both provide eight quasi-bidirectional ports, a 1 MHz I2C interface, and a 16-pin SOIC footprint. The principal difference is the slave address required by firmware.
When should I choose PCA9674D over another I/O expander?
Choose the PCA9674D when an existing 16-pin SOIC design needs eight I2C-controlled quasi-bidirectional ports, a 1 MHz bus, and an interrupt output without changing its PCB. It is particularly suitable for switch monitoring and LED control. For a new design, compare the full electrical and address requirements because newer devices may use different port architectures or register maps.
Is PCA9674D suitable for LED dimming and industrial control?
The PCA9674D is suitable for LED dimming and industrial digital-I/O expansion because it supports 1 MHz I2C transfers and eight quasi-bidirectional output ports. PWM-capable output control can support dimming functions when the host writes the required timing data. For solenoid, relay, or other inductive loads, add suitable driver and protection circuitry rather than switching the load directly.
How many PCA9674D devices can share one I2C bus?
Up to 64 PCA9674D devices can be selected by hardware address, while the PCA9674 and PCA9674A families can coexist because their slave addresses do not overlap. The NXP datasheet states that 126 devices across both families can occupy one bus without buffers, representing up to 1,008 I/Os. Actual bus loading and pull-up design still require normal I2C validation.
Where can I buy PCA9674D online?
Use the Request a Quote form on this page to ask for PCA9674D availability, current unit pricing, and lead time. The NXP product page identifies the base device as no longer manufactured, while distributor order forms such as PCA9674D,512 and PCA9674D,518 remain associated with the 16-SOIC device. State the required order code and quantity in the quote request.
What is the price of PCA9674D?
Current PCA9674D pricing depends on order code, quantity, condition, and supply status. Submit a Request a Quote on this page for the exact unit and volume requirements you need. The base NXP listing states that PCA9674D is no longer manufactured, so the requested package order form and any authorized channel inventory should be confirmed before placing an order.
What is the lead time for PCA9674D?
The current lead time depends on the selected order form, quantity, and available manufacturer or channel inventory. Use the Request a Quote form on this page and specify whether PCA9674D,512 or PCA9674D,518 is required. The NXP product page identifies PCA9674D as no longer manufactured, making an explicit supply confirmation especially important for production quantities.
Is PCA9674D in stock?
Stock status changes by order form and quantity, so use the Request a Quote form on this page for a current availability answer. Identify the required 16-pin SOIC order code and production quantity in the request. The NXP listing identifies PCA9674D as no longer manufactured, which means availability should be confirmed before committing a new build to this device.
What are the key specifications of PCA9674D that engineers should know?
The PCA9674D combines eight quasi-bidirectional GPIO ports, a 1 MHz I2C Fast-mode Plus interface, three address-selection inputs, and an interrupt output in a 16-pin SOIC. Its 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V embedded systems. According to the NXP datasheet, three address inputs allow 64 hardware-selectable addresses within the PCA9674 family.

工程參考資料,適用於 PCA9674D — 比較、設計指引及合規資訊。

選型指南

Choose the PCA9674D for an existing 16-SOIC design that requires eight quasi-bidirectional ports, a 1 MHz I2C interface, and an interrupt output without changing its PCB or firmware. Select PCA9674AD,512 when the original device cannot be obtained and the firmware can be changed to the PCA9674A slave-address range; its documented package and terminal compatibility make it a direct drop-in choice. Select PCA9674AD,518 when automated tape-and-reel assembly is required, accepting the same address update as the tube-packed alternative. For a completely new design, compare port architecture, current handling, address space, and register compatibility before choosing any expander. Parts such as PCF8574 may serve similar GPIO-expansion functions but are not presented as direct replacements because their bus speed, pin arrangement, and operating behavior differ.

與替代品比較

參數 本產品 PCA9674AD,512 PCA9674AD,518
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 16-SOIC 16-SOIC - same 16-SOIC - same
Device Function Remote 8-bit I/O expander Remote 8-bit I/O expander Remote 8-bit I/O expander
I/O Port Count 8 8 8
I2C Clock Frequency 1 MHz 1 MHz 1 MHz
Supply Voltage 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
Slave Address Family PCA9674 address range PCA9674A address range PCA9674A address range
Interrupt Output Yes Yes Yes
Hardware Address Inputs 3 3 3
Order Form PCA9674D Tube order form Tape-and-reel order form

主要差異化特點

  • Direct address-range transition within the same device family (對比PCA9674AD,512)
  • Production packaging flexibility for the same 16-SOIC design (對比PCA9674AD,518)
  • Higher bus rate than standard 100 kHz I2C designs (對比PCA9674AD,512)

設計說明

Use the 16-pin SOIC footprint associated with the NXP package drawing and verify pin 1 orientation against the PCB silkscreen. Place the device near the connector or controlled peripheral group it serves to keep the eight port traces short. Route SCL and SDA away from inductive or high-current switching paths, and provide the supply bypass capacitor close to VDD with a short ground return to VSS.

Do not assume that a PCA9674A can use the original PCA9674 slave address. The NXP datasheet states that the devices are identical except for their non-overlapping slave addresses. Update firmware and verify that no other device already occupies the new address. Also avoid using a quasi-bidirectional port as a push-pull output driver for loads requiring a guaranteed low output resistance.

Estimate the total I2C pull-up current before selecting resistor values, including the current required by every device on the bus. The bus must remain within the electrical limits of the host and all expanders, and the pull-up voltage must match the bus logic level. Add local supply decoupling at the PCA9674D and avoid routing the interrupt trace beside noisy power stages when a sensitive host input is connected.

Assign the A0, A1, and A2 levels during hardware planning because they determine the device's slave address. Tie the address pins only to the levels allowed by the NXP datasheet and make the routing easy to inspect during production review. For LED matrices or multichannel panels, keep port-to-driver paths short and provide a quiet return path so switching currents do not share sensitive signal ground routes.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The NXP product information identifies PCA9674D as no longer manufactured. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated on the accessed product pages.

資料驗證日期: 2026-11-14 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

PCA9674D datasheet PCA9674D pinout PCA9674D datasheet pdf PCA9674D equivalent PCA9674D replacement PCA9674D cross reference PCA9674D vs PCA9674AD,512 PCA9674D footprint PCA9674D application circuit PCA9674D price PCA9674D stock NXP PCA9674D

相關元件與詞彙

NXP Semiconductors PCA9674D PCA9674AD,512 PCA9674AD,518 I/O expander GPIO expander interface IC microcontroller peripheral I2C-bus Fast-mode Plus Fm+ quasi-bidirectional port 1 MHz I2C 2.3 V to 5.5 V supply 16-pin SOIC SOIC package family surface-mount package interrupt output hardware-selectable slave address LED dimming industrial control smart-home sensor aggregation STM32G031K8T6TR PCA9674A
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情