Texas Instruments

PCF8574DWE4 - 8-Bit I2C I/O Expander | Texas Instruments

部品番号: PCF8574DWE4 ✓ 生産中
2.5 V to 6 V Vdss 10 µA maximum Id 16-pin SOIC Package 100 kHz Speed
MOQ: 1 |

PCF8574DWE4 概要

The Texas Instruments PCF8574DWE4 is an 8-bit remote input/output expander for the two-wire bidirectional I2C bus, operating from 2.5 V to 6 V VCC with eight quasi-bidirectional I/O lines and a 100 kHz I2C interface. The device is supplied in a 16-pin SOIC package with a 1.27 mm terminal pitch.

An I2C I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a host microcontroller or processor. It belongs to the parallel I/O port hierarchy, extends the I2C interface family, and reduces the number of GPIO pins required on the controlling device. Each port pin can be selected as an input or output through the device register interface, while the open-drain INT output can notify the host of an input state change.

The PCF8574DWE4 provides eight individually controlled I/O lines, operation across a 2.5 V to 6 V supply range, and I2C communication at up to 100 kHz. Its low standby-current consumption is 10 µA maximum. The three external address inputs permit multiple expanders to share an I2C bus when their hardware addresses are configured differently, while the package supports conventional surface-mount PCB assembly.

The device uses quasi-bidirectional port architecture, allowing each P0 through P7 line to operate as an input or output under software control. Pull-up resistors are normally required for open-drain bus signals. Because the I2C pins also support 3-state operation, a port can be disconnected temporarily to support bus communication involving devices that detect a target address on the same bus.

Typical applications include industrial control panels, sensor and relay interfaces, LED status indicators, keyboard scanners, programmable logic controllers, and compact embedded systems. The 8-bit port width is particularly useful when a controller must monitor discrete switches or command several actuators without allocating eight dedicated GPIO pins to every function.

PCB design should preserve short I2C routing, provide pull-up resistors on SDA and SCL, and keep the address-strapping tracks accessible if multiple device addresses are required. Validate the controller voltage, peripheral voltage, and logic thresholds when the expander operates from a supply different from the I2C bus pull-up level. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.

This product page organizes the operating limits, interface details, package information, replacement candidates, and practical implementation considerations needed to evaluate the PCF8574DWE4 in an embedded I2C design.

ドロップイン代替品: PCF8574DWE4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

PCA8574D/518

✅ ドロップイン
📦 SOIC-16
I2C rate is 400 kHz versus 100 kHz, and the identified supply limit is 5.5 V versus 6 V; verify address, reset, and interrupt behavior

📋 参考代替品(カタログ未掲載)

PCF8574T/3,518

✅ ドロップイン
📦 SOIC-16
Same identified 8-bit, 100 kHz I2C interface and 2.5 V to 6 V supply range; address, reset, and timing details still require comparison

📋 参考代替品(カタログ未掲載)

PCF8574AT-T

✅ ドロップイン
📦 SOIC-16
Identified PCF8574-family alternative with differing suffix characteristics; key voltage, timing, address, and reset values require verification

📋 参考代替品(カタログ未掲載)

PCF8574DWE4 仕様

Product Type Remote 8-bit I/O expander
Number of I/O Lines 8 lines
インターフェース I2C two-wire bidirectional bus
Maximum I2C Clock Frequency 100 kHz
Supply Voltage Range 2.5 V to 6 V
Low Standby Current 10 µA maximum
動作温度範囲 -40 °C to +85 °C
Temperature Grade Industrial
パッケージ 16-pin SOIC
Package Code SOP
Terminal Pitch 1.27 mm
Terminal Form Gull wing
Package Shape Rectangular
Number of Terminals 16
Address Inputs 3 hardware-selectable inputs
Port Architecture Quasi-bidirectional
実装タイプ Surface mount
RoHS ステータス unknown
REACH Status unknown
AEC-Q100 Qualification unknown

PCF8574DWE4 ピン構成

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
ピン 1 A0 — Address input A0
ピン 2 A1 — Address input A1
ピン 3 A2 — Address input A2
ピン 4 VSS — Ground supply
ピン 5 P0 — Quasi-bidirectional I/O port 0
ピン 6 P1 — Quasi-bidirectional I/O port 1
ピン 7 P2 — Quasi-bidirectional I/O port 2
ピン 8 P3 — Quasi-bidirectional I/O port 3
ピン 9 P4 — Quasi-bidirectional I/O port 4
ピン 10 P5 — Quasi-bidirectional I/O port 5
ピン 11 P6 — Quasi-bidirectional I/O port 6
ピン 12 P7 — Quasi-bidirectional I/O port 7
ピン 13 INT — Active-low open-drain interrupt output
ピン 14 SCL — I2C serial clock
ピン 15 SDA — I2C serial data
ピン 16 VCC — Power supply

主な用途

PCF8574DWE4 の用途: 6 件s: Industrial Control Panel I/O, Relay and Discrete Actuator Interface, Sensor and Discrete Switch Hub, LED Status and Indicator Control, PLC and Remote Automation Interface, Embedded Keyboard and Front-Panel Interface.

🏭

Industrial Control Panel I/O

The PCF8574DWE4 fits industrial control-panel designs that need more panel inputs and outputs than the host controller provides directly. Its eight quasi-bidirectional lines can read switch states or operate indicator and relay-driver circuits, while the 2.5 V to 6 V supply range supports common industrial logic levels. The 100 kHz I2C rate is suitable for periodic status polling rather than high-bandwidth data transfer. Configure the A0, A1, and A2 inputs to avoid address conflicts when several panels use expanders on one bus. Pull-ups are required on SDA and SCL, and each port line used as an input should be conditioned to remain within the device voltage limits.

⚡

Relay and Discrete Actuator Interface

The PCF8574DWE4 provides a compact way for an embedded controller to command grouped relays, latches, or other discrete actuators through an eight-bit port. Its 2.5 V to 6 V operating range allows the interface to share a compatible supply with the controller, and the 100 kHz I2C bus limits the update rate but is adequate for ordinary on/off sequencing. Because the ports are quasi-bidirectional, external driver transistors or suitable interface logic are normally used when driving relays or other loads. Use the interrupt output and input-capable port lines to confirm actuator or switch state, while ensuring pull-up values suit the port voltage and load characteristics.

🧩

Sensor and Discrete Switch Hub

The PCF8574DWE4 is useful when several slow-changing sensors, selectors, or discrete switches must be connected to a controller with limited GPIO resources. Eight port lines can sample switch positions or provide digital interface points for external sensing circuits, and the active-low INT output can signal a changed input state to the host. The device operates from 2.5 V to 6 V and communicates at up to 100 kHz, making it appropriate for status monitoring rather than high-speed sensing. Firmware must account for the quasi-bidirectional port behavior and perform a consistent write-read sequence when changing a port from output to input.

💡

LED Status and Indicator Control

The PCF8574DWE4 can drive groups of LED status indicators where a host controller has too few available output pins. Eight software-addressed outputs simplify sequence, alarm, and operating-state displays, while the 2.5 V to 6 V device range accommodates common embedded supply levels. At the maximum 100 kHz I2C rate, output updates are suitable for human-visible indications and low-duty equipment status functions. Use suitable series resistors with LEDs and ensure the port output-current and total package limits in the manufacturer datasheet are respected. Debounce mechanical inputs in firmware or place appropriate filtering at the connector.

🔧

PLC and Remote Automation Interface

The PCF8574DWE4 can extend a small programmable controller with local digital I/O for remote automation modules. Three hardware address inputs allow multiple expanders to be placed on one I2C bus, which simplifies distributed panel nodes when the I2C bus length and loading remain suitable. The 8-bit port width is effective for mixed digital input and output groups, and the 100 kHz interface rate is sufficient for periodic state polling and command updates. Select pull-ups for the actual bus voltage, protect externally connected wiring against ESD and transients, and use the INT pin to reduce unnecessary polling when input states change.

🔧

Embedded Keyboard and Front-Panel Interface

The PCF8574DWE4 is suited to scanning compact keyboards, rotary selectors, or front-panel switches when direct host GPIO pins are constrained. Eight lines can be assigned to scanned inputs, with external pull-up or pull-down components establishing stable logic states. The active-low open-drain INT output provides a convenient change-notification path to the host, allowing the controller to remain idle between user actions. The 100 kHz I2C rate and 2.5 V to 6 V operating range suit conventional embedded control loops. Account for switch bounce in firmware, keep the scan matrix electrically manageable, and verify that all front-panel signals remain within the expander's logic thresholds.

What is the PCF8574DWE4?
The PCF8574DWE4 is a Texas Instruments remote 8-bit I/O expander for the two-wire bidirectional I2C bus. According to the manufacturer datasheet, it operates from 2.5 V to 6 V, provides eight individually addressed port lines, supports I2C operation up to 100 kHz, and is packaged in a 16-pin SOIC. Its primary function is to add GPIO capability to a host controller that has too few external pins.
What are the key specifications of PCF8574DWE4 that engineers should know?
The PCF8574DWE4 combines eight I/O lines with a 2.5 V to 6 V operating range and a maximum 100 kHz I2C clock rate. The Texas Instruments datasheet also specifies low standby-current consumption of 10 µA maximum, an industrial temperature range of -40 °C to +85 °C, and a 16-pin SOIC package with 1.27 mm pitch. Three address inputs allow multiple expanders to coexist on one bus when their addresses are configured separately.
How do I connect the PCF8574DWE4 to an I2C bus?
Connect VCC and VSS to the device supply and ground, connect SCL and SDA to the corresponding I2C bus lines, and configure the A0, A1, and A2 address inputs for the required hardware address. According to the Texas Instruments pin description, INT is an active-low open-drain interrupt output. Pull-up resistors are needed on SDA, SCL, and any quasi-bidirectional port line used as an input or output.
Where can I download the PCF8574DWE4 datasheet PDF?
The official PCF8574DWE4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/pcf8574.pdf. The datasheet contains the electrical characteristics, register map, address configuration, power-on reset behavior, timing information, and the 16-pin SOIC pin description. Use that pin-description table when creating the PCB footprint and assigning each net.
Where can I find the PCF8574DWE4 pinout?
The PCF8574DWE4 pinout is shown in the Texas Instruments PCF8574 manufacturer datasheet. Pins 1 through 3 are A0, A1, and A2; pins 5 through 12 are P0 through P7; pin 4 is VSS; pin 13 is INT; pins 14 and 15 are SCL and SDA; and pin 16 is VCC. The device uses a 16-pin SOIC footprint with 1.27 mm terminal pitch.
Is PCF8574DWE4 suitable for low-voltage industrial designs?
The PCF8574DWE4 is suitable for low-voltage designs operating within its published electrical limits. The manufacturer specifies a 2.5 V to 6 V VCC range and a -40 °C to +85 °C industrial temperature range. Compatibility with a specific 3.3 V or 5 V system also depends on the I2C pull-up voltage and signal-level limits of the connected controller and peripheral devices.
How many I2C devices can share a bus with PCF8574DWE4?
The PCF8574DWE4 provides three hardware address inputs, A0, A1, and A2, giving eight selectable address combinations. Multiple devices can therefore share one I2C bus when their address straps are configured for different combinations. The manufacturer datasheet identifies the address pins, but the final bus-device count also depends on the bus capacitance, pull-up selection, address allocation, and other devices connected to the same bus.
What is the difference between PCF8574DWE4 and PCA8574D?
The PCF8574DWE4 supports I2C operation up to 100 kHz across a 2.5 V to 6 V supply range, while the identified PCA8574D comparison candidate is described as supporting up to 400 kHz and 5.5 V operation. Both are presented as 16-pin I2C I/O expanders, but a design should verify address behavior, power-on reset timing, output characteristics, and every pin connection before treating one as a direct replacement.
What is the best NXP equivalent for PCF8574DWE4?
The NXP PCF8574T/3,518 is the closest identified cross-brand candidate because it is described as an 8-bit, 100 kHz I2C expander with a 2.5 V to 6 V operating range in a 16-pin SOIC. It is therefore a strong functional candidate, but engineers should still compare address mapping, interrupt polarity, power-on reset behavior, and absolute maximum ratings before approving a drop-in substitution.
Can PCF8574AT-T replace PCF8574DWE4?
The PCF8574AT-T is identified as an alternative PCF8574-family device, but a replacement should not be approved from the family name alone. The cross-reference information does not establish every electrical and timing characteristic, so verify the 16-pin SOIC footprint, I2C address behavior, 2.5 V to 6 V operating range, 100 kHz interface rate, port electrical characteristics, and interrupt behavior against the Texas Instruments datasheet before production use.
When should I choose PCF8574DWE4 instead of PCA8574D?
Choose PCF8574DWE4 when a design requires the PCF8574 register behavior, operation from 2.5 V to 6 V, and an I2C rate of up to 100 kHz. Consider PCA8574D when the system needs a higher I2C clock rate of up to 400 kHz and its other electrical characteristics satisfy the design. The choice should be based on complete timing, addressing, reset, and pin-level comparison rather than package appearance alone.
What can replace PCF8574DWE4?
PCF8574DWE4 can be evaluated against the Texas Instruments PCA8574D/518, NXP PCF8574T/3,518, and NXP PCF8574AT-T as identified family alternatives. A true drop-in choice must retain the same 16-pin SOIC footprint and preserve the required address, supply, timing, interrupt, and port characteristics. Only the NXP PCF8574T/3,518 candidate is specifically described with the same 100 kHz and 2.5 V to 6 V headline ratings.
Where can I buy PCF8574DWE4 and check its lead time?
Use the Request a Quote form on this page to request PCF8574DWE4 availability, current lead time, and order details from XAIPART. The request should include your required quantity, shipment destination, and packaging preference. Because this product is commonly ordered as a standard catalog component, include the exact MPN PCF8574DWE4 to avoid confusion with other PCF8574 package or ordering-code variants.
Is PCF8574DWE4 in stock?
PCF8574DWE4 availability should be confirmed through the Request a Quote form on this page using the exact MPN and requested quantity. Inventory can change with order volume, packaging requirements, and replenishment timing. For a production BOM, request confirmation of the 16-pin SOIC package, operating temperature grade, delivery schedule, and quantity needed before releasing the manufacturing order.
How do I choose pull-up resistors for PCF8574DWE4 I2C lines?
Select SDA and SCL pull-up values for the bus voltage, total bus capacitance, operating speed, and leakage current rather than using a universal resistor value. The Texas Instruments datasheet provides the device's I2C characteristics and timing information. Keep pull-up placement close to the bus master where practical, verify rise times at the 100 kHz maximum rate, and ensure every pulled-up signal remains below the connected device's voltage tolerance.

エンジニアリング参考データ: PCF8574DWE4 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose PCF8574DWE4 when the design requires the established Texas Instruments PCF8574 behavior, eight quasi-bidirectional I/O lines, a 2.5 V to 6 V supply range, and I2C operation at up to 100 kHz. It is appropriate for conventional industrial panels, discrete switch and relay interfaces, LED indicators, and compact embedded controllers. Consider PCA8574D/518 when a higher 400 kHz I2C rate is valuable, while recognizing its identified 5.5 V upper supply limit and the need to verify address, reset, and interrupt behavior. NXP PCF8574T/3,518 is the closest cross-brand candidate because its identified 8-bit, 100 kHz, 2.5 V-to-6 V ratings align with the target. PCF8574AT-T may suit an approved PCF8574-family alternate sourcing plan, but its key electrical and timing details should be confirmed before substitution. For every candidate, verify the 16-pin SOIC footprint, hardware addressing, power-on reset, INT behavior, port drive limits, and temperature grade.

代替品との比較

パラメータ この製品 PCA8574D/518 PCF8574T/3,518 PCF8574AT-T
Brand Texas Instruments Texas Instruments NXP Semiconductors NXP Semiconductors

主な差別化要因

  • Matches the identified NXP candidate on the principal interface ratings (vs PCF8574T/3,518)
  • Supports a higher specified maximum I2C clock rate (vs PCA8574D/518)
  • Provides the higher stated upper supply limit (vs PCA8574D/518)
  • Provides documented low standby-current consumption (vs PCF8574AT-T)

設計ノート

Place the SOIC-16 footprint according to the Texas Instruments package drawing and keep the A0, A1, and A2 address straps close to pins 1 through 3. Provide clear access to each strap if several expander addresses must be configured on one board. Check the board's polarity markings and pin-1 orientation against the manufacturer pin-description table before fabrication.

Do not treat the quasi-bidirectional ports as ordinary push-pull outputs or inputs without external pull resistors. When changing a port from output to input, follow the recommended write-read sequence so the port latch does not briefly drive the external circuit. Account for switch bounce and input leakage, and do not allow a port to exceed its voltage or current limits when external circuitry is connected.

Select SDA and SCL pull-up resistors using the actual bus voltage, total capacitance, leakage, and required rise time. The PCF8574DWE4 supports I2C operation up to 100 kHz, so verify that the assembled bus still meets timing at that rate. Keep the bus routing short, minimize stubs, and use a common-ground reference between the expander and controller.

Operate the device only within its specified 2.5 V to 6 V VCC range and ensure the I2C pull-up voltage does not exceed the device's permitted signal level. Place the local supply bypass capacitor close to VCC and VSS to maintain a low-impedance supply path. When the controller and expander use different logic domains, confirm that every I2C and port signal remains electrically compatible.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No specific compliance declaration was identified for the exact PCF8574DWE4 ordering code. Request current compliance documentation through the Request a Quote form when it is required by the purchasing or quality process.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

PCF8574DWE4 datasheet PCF8574DWE4 datasheet pdf PCF8574DWE4 pinout PCF8574DWE4 specifications Texas Instruments PCF8574DWE4 PCF8574DWE4 equivalent PCF8574DWE4 replacement PCF8574DWE4 cross reference PCF8574DWE4 vs PCA8574D PCF8574DWE4 SOIC-16 footprint PCF8574DWE4 application circuit PCF8574DWE4 price PCF8574DWE4 stock PCF8574DWE4 lead time

関連部品&用語

Texas Instruments PCF8574DWE4 PCF8574 PCA8574D/518 PCF8574T/3,518 PCF8574AT-T remote 8-bit I/O expander parallel I/O port I2C two-wire bidirectional bus interface IC GPIO expander quasi-bidirectional port SOIC-16 SOIC package family surface-mount package open-drain interrupt power management industrial control relay interface LED indicator sensor hub 2.5 V to 6 V 100 kHz I2C 10 µA standby current A0 A1 A2 address inputs
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示