PCF8574DWE4 - 8-Bit I2C I/O Expander | Texas Instruments
MPN: PCF8574DWE4 ✓ فعالPCF8574DWE4 جائزہ
An I2C I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a host microcontroller or processor. It belongs to the parallel I/O port hierarchy, extends the I2C interface family, and reduces the number of GPIO pins required on the controlling device. Each port pin can be selected as an input or output through the device register interface, while the open-drain INT output can notify the host of an input state change.
The PCF8574DWE4 provides eight individually controlled I/O lines, operation across a 2.5 V to 6 V supply range, and I2C communication at up to 100 kHz. Its low standby-current consumption is 10 µA maximum. The three external address inputs permit multiple expanders to share an I2C bus when their hardware addresses are configured differently, while the package supports conventional surface-mount PCB assembly.
The device uses quasi-bidirectional port architecture, allowing each P0 through P7 line to operate as an input or output under software control. Pull-up resistors are normally required for open-drain bus signals. Because the I2C pins also support 3-state operation, a port can be disconnected temporarily to support bus communication involving devices that detect a target address on the same bus.
Typical applications include industrial control panels, sensor and relay interfaces, LED status indicators, keyboard scanners, programmable logic controllers, and compact embedded systems. The 8-bit port width is particularly useful when a controller must monitor discrete switches or command several actuators without allocating eight dedicated GPIO pins to every function.
PCB design should preserve short I2C routing, provide pull-up resistors on SDA and SCL, and keep the address-strapping tracks accessible if multiple device addresses are required. Validate the controller voltage, peripheral voltage, and logic thresholds when the expander operates from a supply different from the I2C bus pull-up level. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
This product page organizes the operating limits, interface details, package information, replacement candidates, and practical implementation considerations needed to evaluate the PCF8574DWE4 in an embedded I2C design.
کے لیے ڈراپ اِن متبادل PCF8574DWE4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
PCA8574D/518
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCF8574T/3,518
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCF8574AT-T
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCF8574DWE4 تفصیلات
| Product Type | Remote 8-bit I/O expander |
| Number of I/O Lines | 8 lines |
| انٹرفیس | I2C two-wire bidirectional bus |
| Maximum I2C Clock Frequency | 100 kHz |
| Supply Voltage Range | 2.5 V to 6 V |
| Low Standby Current | 10 µA maximum |
| آپریٹنگ درجہ حرارت رینج | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| پیکیج | 16-pin SOIC |
| Package Code | SOP |
| Terminal Pitch | 1.27 mm |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Number of Terminals | 16 |
| Address Inputs | 3 hardware-selectable inputs |
| Port Architecture | Quasi-bidirectional |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
PCF8574DWE4 پن کنفیگریشن
| پن 1 | A0 — Address input A0 |
| پن 2 | A1 — Address input A1 |
| پن 3 | A2 — Address input A2 |
| پن 4 | VSS — Ground supply |
| پن 5 | P0 — Quasi-bidirectional I/O port 0 |
| پن 6 | P1 — Quasi-bidirectional I/O port 1 |
| پن 7 | P2 — Quasi-bidirectional I/O port 2 |
| پن 8 | P3 — Quasi-bidirectional I/O port 3 |
| پن 9 | P4 — Quasi-bidirectional I/O port 4 |
| پن 10 | P5 — Quasi-bidirectional I/O port 5 |
| پن 11 | P6 — Quasi-bidirectional I/O port 6 |
| پن 12 | P7 — Quasi-bidirectional I/O port 7 |
| پن 13 | INT — Active-low open-drain interrupt output |
| پن 14 | SCL — I2C serial clock |
| پن 15 | SDA — I2C serial data |
| پن 16 | VCC — Power supply |
عام استعمالات
PCF8574DWE4 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Panel I/O, Relay and Discrete Actuator Interface, Sensor and Discrete Switch Hub, LED Status and Indicator Control, PLC and Remote Automation Interface, Embedded Keyboard and Front-Panel Interface.
Industrial Control Panel I/O
The PCF8574DWE4 fits industrial control-panel designs that need more panel inputs and outputs than the host controller provides directly. Its eight quasi-bidirectional lines can read switch states or operate indicator and relay-driver circuits, while the 2.5 V to 6 V supply range supports common industrial logic levels. The 100 kHz I2C rate is suitable for periodic status polling rather than high-bandwidth data transfer. Configure the A0, A1, and A2 inputs to avoid address conflicts when several panels use expanders on one bus. Pull-ups are required on SDA and SCL, and each port line used as an input should be conditioned to remain within the device voltage limits.
تجویز کردہ
Relay and Discrete Actuator Interface
The PCF8574DWE4 provides a compact way for an embedded controller to command grouped relays, latches, or other discrete actuators through an eight-bit port. Its 2.5 V to 6 V operating range allows the interface to share a compatible supply with the controller, and the 100 kHz I2C bus limits the update rate but is adequate for ordinary on/off sequencing. Because the ports are quasi-bidirectional, external driver transistors or suitable interface logic are normally used when driving relays or other loads. Use the interrupt output and input-capable port lines to confirm actuator or switch state, while ensuring pull-up values suit the port voltage and load characteristics.
تجویز کردہ
Sensor and Discrete Switch Hub
The PCF8574DWE4 is useful when several slow-changing sensors, selectors, or discrete switches must be connected to a controller with limited GPIO resources. Eight port lines can sample switch positions or provide digital interface points for external sensing circuits, and the active-low INT output can signal a changed input state to the host. The device operates from 2.5 V to 6 V and communicates at up to 100 kHz, making it appropriate for status monitoring rather than high-speed sensing. Firmware must account for the quasi-bidirectional port behavior and perform a consistent write-read sequence when changing a port from output to input.
تجویز کردہ
LED Status and Indicator Control
The PCF8574DWE4 can drive groups of LED status indicators where a host controller has too few available output pins. Eight software-addressed outputs simplify sequence, alarm, and operating-state displays, while the 2.5 V to 6 V device range accommodates common embedded supply levels. At the maximum 100 kHz I2C rate, output updates are suitable for human-visible indications and low-duty equipment status functions. Use suitable series resistors with LEDs and ensure the port output-current and total package limits in the manufacturer datasheet are respected. Debounce mechanical inputs in firmware or place appropriate filtering at the connector.
تجویز کردہ
PLC and Remote Automation Interface
The PCF8574DWE4 can extend a small programmable controller with local digital I/O for remote automation modules. Three hardware address inputs allow multiple expanders to be placed on one I2C bus, which simplifies distributed panel nodes when the I2C bus length and loading remain suitable. The 8-bit port width is effective for mixed digital input and output groups, and the 100 kHz interface rate is sufficient for periodic state polling and command updates. Select pull-ups for the actual bus voltage, protect externally connected wiring against ESD and transients, and use the INT pin to reduce unnecessary polling when input states change.
تجویز کردہ
Embedded Keyboard and Front-Panel Interface
The PCF8574DWE4 is suited to scanning compact keyboards, rotary selectors, or front-panel switches when direct host GPIO pins are constrained. Eight lines can be assigned to scanned inputs, with external pull-up or pull-down components establishing stable logic states. The active-low open-drain INT output provides a convenient change-notification path to the host, allowing the controller to remain idle between user actions. The 100 kHz I2C rate and 2.5 V to 6 V operating range suit conventional embedded control loops. Account for switch bounce in firmware, keep the scan matrix electrically manageable, and verify that all front-panel signals remain within the expander's logic thresholds.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCF8574DWE4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PCA8574D/518 | PCF8574T/3,518 | PCF8574AT-T |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
اہم امتیازی خصوصیات
- Matches the identified NXP candidate on the principal interface ratings (بمقابلہPCF8574T/3,518)
- Supports a higher specified maximum I2C clock rate (بمقابلہPCA8574D/518)
- Provides the higher stated upper supply limit (بمقابلہPCA8574D/518)
- Provides documented low standby-current consumption (بمقابلہPCF8574AT-T)
ڈیزائن نوٹس
Place the SOIC-16 footprint according to the Texas Instruments package drawing and keep the A0, A1, and A2 address straps close to pins 1 through 3. Provide clear access to each strap if several expander addresses must be configured on one board. Check the board's polarity markings and pin-1 orientation against the manufacturer pin-description table before fabrication.
Do not treat the quasi-bidirectional ports as ordinary push-pull outputs or inputs without external pull resistors. When changing a port from output to input, follow the recommended write-read sequence so the port latch does not briefly drive the external circuit. Account for switch bounce and input leakage, and do not allow a port to exceed its voltage or current limits when external circuitry is connected.
Select SDA and SCL pull-up resistors using the actual bus voltage, total capacitance, leakage, and required rise time. The PCF8574DWE4 supports I2C operation up to 100 kHz, so verify that the assembled bus still meets timing at that rate. Keep the bus routing short, minimize stubs, and use a common-ground reference between the expander and controller.
Operate the device only within its specified 2.5 V to 6 V VCC range and ensure the I2C pull-up voltage does not exceed the device's permitted signal level. Place the local supply bypass capacitor close to VCC and VSS to maintain a low-impedance supply path. When the controller and expander use different logic domains, confirm that every I2C and port signal remains electrically compatible.
تعمیل کی معلومات
No specific compliance declaration was identified for the exact PCF8574DWE4 ordering code. Request current compliance documentation through the Request a Quote form when it is required by the purchasing or quality process.