PEX8604-BA50BI - 4-Lane Gen 2 PCIe Switch | Broadcom
部品番号: PEX8604-BA50BI ✓ 生産中PEX8604-BA50BI 概要
A PCI Express switch is a semiconductor that creates additional PCIe links between a root complex or another switch and multiple endpoint devices. It operates within the PCIe hierarchy as a bridge and switch rather than as an endpoint itself. The PEX8604 belongs to the broad PCIe switch and bridge category, which supports fan-out, embedded systems, consumer equipment, and high-availability platforms where downstream devices must communicate with a central host.
The principal device characteristics are four Gen 2 lanes, a maximum of four ports, and a 5.0 GT/s per-lane signaling rate. Broadcom describes the PEX8604 as its smallest four-lane Gen 2 device. The switch also supports PCIe hot-plug functionality for supported downstream configurations, making it relevant to systems where expansion modules are replaced or maintained without powering down the complete platform.
The 196-BGA package provides a high pin count for power, ground, high-speed transmit and receive paths, configuration interfaces, reference clocks, and control signals. Such a package also places substantial emphasis on compact board area. Achieving correct Gen 2 operation therefore requires careful PCB layer planning, controlled impedance routing, uninterrupted reference planes, and power-delivery design that meets the device's low- and high-speed requirements.
Typical uses include embedded computing platforms, consumer appliances, PCI Express endpoint aggregation, expansion systems, and high-availability equipment with hot-pluggable modules. In these systems, the switch expands one host-facing PCIe connection into multiple downstream links while allowing port-level routing and monitoring functions according to the device configuration.
A primary design consideration is signal integrity. The 5.0 GT/s interface requires short, impedance-controlled routes, solid reference planes, suitable via transitions, and connector or package escape geometry designed for low loss. Power sequencing, clock distribution, reset behavior, and the firmware-supported link configuration must also be validated together; satisfying individual data-sheet limits in isolation does not guarantee stable operation across every board stack-up and temperature condition.
This product overview synthesizes the manufacturer capabilities, package information, cross-reference findings, and practical implementation considerations into an engineering-focused guide. It also distinguishes documented characteristics from parameters that still require confirmation from the full technical documentation before a new board design is released.
ドロップイン代替品: PEX8604-BA50BI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
PEX8604-BA50BI G
✅ ドロップイン📋 参考代替品(カタログ未掲載)
PEX8604-BA50BC
✅ ドロップイン価格はお問い合わせください
データシートを見る →PEX8604-BA50BI 最大定格&電気的特性
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| PCI Express Lane Count | 4 lanes |
| Maximum Port Count | 4 ports |
| Per-Lane Data Rate | 5.0 GT/s |
| PCI Express Base Specification | Revision 2.0 |
| パッケージ | 196-BGA (15 mm x 15 mm) |
| Ball Count | 196 balls |
| Core Operating Voltage | 0.95 V to 1.05 V |
| Hot-Plug Support | Supported for applicable downstream-port configurations |
| Device Classification | Analog Switches - Special Purpose / PCI Interface IC |
| Signal Standard | PCI Express |
| Interface Direction | Host-facing to multiple downstream endpoint ports |
| 実装タイプ | Surface mount |
PEX8604-BA50BI 196-bga (15 mm x 15 mm) ピン配置ガイド
PEX8604-BA50BI (196-bga (15 mm x 15 mm) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: PEX8604-BA50BI.
詳細は データシート をご参照ください。
主な用途
PEX8604-BA50BI の用途: 6 件s: Embedded PCIe Endpoint Aggregation, Consumer Multi-Device Expansion, High-Availability PCIe Expansion, PCIe Storage Controller Hub, PCIe Network Interface Aggregation, PCIe Test and Measurement Platform.
Embedded PCIe Endpoint Aggregation
The Broadcom PEX8604-BA50BI fits embedded platforms that need several PCIe devices behind one host-facing interface. Four Gen 2 lanes at 5.0 GT/s provide up to four downstream paths for compatible endpoint controllers, allowing storage, networking, or acceleration functions to share a compact platform architecture. The 196-BGA package measures 15 mm by 15 mm, but the design must reserve escape routing, reference planes, clock distribution, and power connections around all 196 balls. Firmware must configure the intended port relationships and validate enumeration, reset behavior, and endpoint capabilities before production deployment.
おすすめ
Consumer Multi-Device Expansion
The PEX8604-BA50BI is appropriate for consumer equipment that needs to expose multiple PCI Express functions without implementing a larger or more complex switch. Broadcom identifies consumer applications as a target for the device, and its four-lane Gen 2 architecture can support several compatible endpoints through up to four downstream ports. System partitioning, device assignment, and power states must be handled by the platform firmware. For compact products, the 15 mm by 15 mm BGA saves board area relative to larger switch packages, although careful escape routing and assembly control remain necessary.
おすすめ
High-Availability PCIe Expansion
The Broadcom PEX8604-BA50BI supports hot-plug capability in applicable configurations where downstream ports connect to PCI Express slots, making it useful in high-availability systems that support field replacement of modules. The four downstream ports and 5.0 GT/s Gen 2 signaling can organize multiple serviceable PCIe functions behind a common host connection. Deployment requires deliberate implementation of connector power management, reset behavior, software presence detection, and fault isolation. Hot-plug support should be validated for the selected board and enclosure because the physical connection alone does not establish complete operational readiness.
おすすめ
PCIe Storage Controller Hub
A PEX8604-based design can connect multiple compatible PCIe storage controllers through the PEX8604-BA50BI's four-lane Gen 2 fabric. The switch presents one host-facing connection while providing up to four downstream endpoint paths, simplifying topology management in compact servers and edge appliances. Performance depends on correct lane allocation, buffer behavior, and device support for the switch's operating modes, so storage devices should be tested with the intended firmware image. PCB implementation must preserve the required return path and power-delivery performance through each high-speed lane.
おすすめ
PCIe Network Interface Aggregation
The PEX8604-BA50BI can fan multiple PCIe-based network interfaces into a single system architecture for edge servers, industrial controllers, and communication appliances. Four Gen 2 lanes at 5.0 GT/s support concurrent endpoint traffic when the switch configuration and attached devices allow it. Thermal and firmware planning should account for the activity of several network controllers sharing the chassis. Signal-integrity validation must cover connector escapes, layer transitions, reference-plane continuity, and clock jitter at every downstream port rather than relying only on schematic connectivity.
おすすめ
PCIe Test and Measurement Platform
The Broadcom PEX8604-BA50BI can support test and measurement systems requiring several compatible PCIe instruments, acquisition engines, or programmable controllers behind one host interface. Its four downstream ports offer a compact way to organize multiple PCIe functions while limiting the physical size of the switching component. For instrumentation, deterministic enumeration, stable reference-clock behavior, and controlled reset sequencing are as important as raw lane bandwidth. The platform should be tested across expected temperature, power, and loading conditions to confirm that each connected endpoint remains stable through the selected link configuration.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PEX8604-BA50BI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PEX8604-BA50BI G | PEX8604-BA50BC |
|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom |
| Package | 196-BGA (15 mm x 15 mm) | 196-BGA (15 mm x 15 mm) | 196-BGA (15 mm x 15 mm) |
| PCI Express Generation | Gen 2 | Gen 2 | Gen 2 |
| Lane Count | 4 lanes | 4 lanes | 4 lanes |
| Maximum Port Count | 4 ports | 4 ports | 4 ports |
| Per-Lane Data Rate | 5.0 GT/s | 5.0 GT/s | 5.0 GT/s |
| Ordering Designation | PEX8604-BA50BI | PEX8604-BA50BI G | PEX8604-BA50BC |
主な差別化要因
- Compact four-lane fan-out in a 196-BGA package (vs PEX8606-BA50BI-G)
- Direct space-separated ordering designation (vs PEX8604-BA50BC)
- Broad application support within the Gen 2 PCIe portfolio (vs PEX8606-BA50BI-G)
設計ノート
Treat the four Gen 2 lanes as 5.0 GT/s differential channels and validate the complete board stack-up rather than only the device footprint. Preserve continuous reference planes beneath each high-speed route, minimize layer transitions, control impedance according to the Broadcom design guide, and verify connector or package escapes with the intended board material. After layout, run signal-integrity simulation and hardware eye measurements across voltage and temperature corners.
Decouple each supply rail at the device with the capacitance and placement required by the manufacturer guidance, and provide low-impedance planes for the 196-BGA power and ground balls. Validate startup sequencing, steady-state droop, and current transients caused by PCIe link activity. Do not infer permissible rail combinations or capacitor values from the 0.95 V to 1.05 V operating range; obtain the complete power architecture from the technical documentation.
Reserve the complete 196-ball escape area before committing the PCB outline. Check component clearance around the BGA, select an assembly process compatible with its pitch and ball layout, and provide inspection access if the package has hidden or closely spaced balls. Keep clock distribution and reset routing isolated from noisy switching nodes, and avoid routing unrelated high-speed signals through the PCIe lane escape region.
Do not substitute a switch solely because its BGA outline appears similar. Confirm the complete ball map, supply rails, reference-clock requirements, configuration interface, reset polarity, lane assignments, firmware support, and ordering code. This is especially important for PEX8604 ordering variants and for the PEX8606 comparison candidate, because functional PCIe compatibility does not automatically establish pin-to-pin drop-in compatibility.
コンプライアンス情報
The accessible product summaries do not explicitly state the target device's RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a PCI Express interface switch rather than an automotive-qualified device.