PEX8605-AB50NI - 4-Lane PCIe Gen 2 Switch | Broadcom
部品番号: PEX8605-AB50NI ✓ 生産中PEX8605-AB50NI 概要
A PCI Express switch is a semiconductor device that expands one PCIe interface into multiple downstream links while managing packet traffic between a host or upstream endpoint and connected peripherals. The PEX8605-AB50NI uses a non-blocking internal switch architecture, supports packet cut-through, and provides full line-rate operation on its ports in supported configurations.
The switch supports PCIe Gen 2 operation with four lanes and four ports. In an x1-to-x1 configuration, the manufacturer documentation identifies a maximum latency of 250 ns. Packet cut-through reduces the time packets remain in the switch, while the non-blocking architecture allows multiple ports to operate concurrently. These characteristics make the device useful for systems needing additional PCIe endpoints without changing the host-side system architecture.
The PEX8605-AB50NI is suitable for embedded computing, industrial controllers, test equipment, storage systems, communications equipment, and consumer appliances requiring multiple PCIe connections. Its 10 x 10 mm aQFN package supports compact board layouts, but high-speed PCIe routing requires careful controlled-impedance layout, solid reference planes, and close decoupling.
The primary design consideration is signal integrity. PCIe differential pairs should be routed as controlled-impedance transmission lines with minimal stubs and discontinuities, while power and ground distribution should provide low-impedance return paths. The 136-aQFN package also requires careful thermal and assembly planning because its fine-pitch lead arrangement complicates rework and demands a suitable land pattern.
This product page combines the manufacturer architecture information with distributor listings and practical integration guidance. It distinguishes verified capabilities from parameters that require confirmation from the complete Broadcom datasheet, helping engineers evaluate the PEX8605-AB50NI for a new embedded or industrial platform.
ドロップイン代替品: PEX8605-AB50NI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストPEX8605-AB50NI 最大定格&電気的特性
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2.0 |
| Lane Count | 4 lanes |
| Port Count | 4 ports |
| パッケージ | 136-aQFN (10 x 10 mm) |
| Internal Architecture | Non-blocking |
| Packet Handling | Packet cut-through |
| Maximum Latency | 250 ns in x1-to-x1 configuration |
| Throughput Behavior | Full line rate on all ports |
| Application Segment | Consumer and embedded applications |
| 実装タイプ | Surface mount |
| ピン数 | 136 pins |
PEX8605-AB50NI 136-aqfn (10 x 10 mm) ピン配置ガイド
PEX8605-AB50NI (136-aqfn (10 x 10 mm) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: PEX8605-AB50NI.
詳細は データシート をご参照ください。
主な用途
PEX8605-AB50NI の用途: 6 件s: Embedded PCIe Expansion, Industrial Control Systems, Test and Measurement Equipment, Network and Communications Equipment, Data Acquisition Systems, Consumer and Embedded Products.
Embedded PCIe Expansion
The PEX8605-AB50NI fits embedded platforms that need to expand a single host-side PCIe connection into multiple downstream links. Its four-lane, four-port Gen 2 architecture gives a system designer room to attach compatible PCIe endpoints while retaining a non-blocking internal switch design. The packet cut-through path and 250 ns maximum latency in an x1-to-x1 configuration are useful for latency-sensitive embedded control, monitoring, or data-acquisition equipment. The 136-aQFN 10 x 10 mm package also helps limit board area compared with larger switch options. Design the host and endpoint links around the manufacturer-supported lane configurations, and validate return paths, reference planes, and power sequencing with PCIe signal-integrity analysis.
おすすめ
Industrial Control Systems
Industrial controllers can use the PEX8605-AB50NI to connect multiple PCIe endpoints to a host processor without requiring a dedicated switch for every peripheral. The four available lanes and four ports support compact endpoint aggregation in machine-control, test, and communication equipment, subject to the endpoint link-width requirements. Full line-rate operation on the supported ports helps preserve throughput when traffic is distributed across independent links. For factory equipment, pay particular attention to thermal cycling, grounding, chassis coupling, and long cable or adapter paths. The PCIe links should remain on controlled-impedance PCB routing, and any external connector or cable transition should be validated separately so it does not consume the system’s PCIe signal-integrity margin.
おすすめ
Test and Measurement Equipment
The PEX8605-AB50NI is useful in test and measurement chassis that need several PCIe endpoints behind one host connection. Possible endpoints include acquisition modules, communication controllers, storage adapters, and programmable logic devices, provided their lane widths and supported topology remain compatible with the switch. The non-blocking architecture supports concurrent port operation, while the four-port configuration simplifies physical partitioning of test resources. Engineers should budget routing space for the 136-aQFN fanout and maintain uninterrupted reference planes beneath every differential pair. Power sequencing must prevent endpoint initialization before the switch and host rails are stable. Where modules connect through backplanes or cables, include channel-loss and connector-budget analysis rather than relying on the board-level PCIe routing alone.
おすすめ
Network and Communications Equipment
Communications equipment can employ the PEX8605-AB50NI to provide dedicated PCIe connectivity for network controllers, security processors, and protocol accelerators. The four lanes and four ports allow designers to avoid sharing one endpoint link across unrelated peripherals and can improve traffic separation at the board level. The switch’s full-line-rate architecture preserves link throughput when the endpoints are active concurrently, and the 10 x 10 mm aQFN package supports dense line cards. The design must still treat PCIe as a high-speed differential interface: use the manufacturer reference topology, avoid stubs, preserve impedance, and provide locally effective decoupling. Confirm the required PCIe base specification, reference-clock architecture, reset behavior, and thermal requirements for the final communications platform.
おすすめ
Data Acquisition Systems
Data-acquisition equipment benefits from the PEX8605-AB50NI when several high-throughput peripherals, such as digitizers, FPGA-based processing cards, or storage targets, require PCIe connectivity. The four-lane Gen 2 switch can consolidate endpoint access behind a host while maintaining non-blocking operation and full line rate across supported ports. This architecture can simplify cable management compared with allocating separate root ports to every instrument. For precision measurements, isolate switching and power-conversion regions from sensitive analog circuitry, use short return paths, and avoid splitting ground or reference planes beneath PCIe pairs. Confirm endpoint lane width and the supported PEX8605 configuration in the manufacturer documentation, then validate the complete path with PCIe compliance and system-level integrity testing.
おすすめ
Consumer and Embedded Products
The PEX8605-AB50NI is explicitly positioned for compact consumer and embedded systems that require additional PCIe connectivity. It can provide a practical path to add storage, networking, acceleration, or display-related PCIe endpoints while preserving a single upstream host interface. Its packet cut-through feature supports low forwarding delay, and the 250 ns x1-to-x1 maximum latency is relevant for interactive embedded workloads. The 10 x 10 mm 136-aQFN package supports dense layouts, although assembly capability and exposed-pad soldering must be considered in the manufacturing plan. Keep high-speed routing away from switching regulators and antenna regions, preserve solid reference planes, and validate the final product under temperature, power, and EMC conditions because enclosure and connector transitions can materially change system-level performance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PEX8605-AB50NI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2.0 |
| Lane Count | 4 lanes |
| Port Count | 4 ports |
| Package | 136-aQFN (10 x 10 mm) |
| Brand | Broadcom |
| Internal Architecture | Non-blocking |
| Maximum Latency | 250 ns in x1-to-x1 configuration |
| Packet Handling | Packet cut-through |
| Throughput Behavior | Full line rate on all ports |
主な差別化要因
- Four-lane, four-port PCIe Gen 2 integration in a compact package (vs No verified drop-in alternative)
- Low-latency packet forwarding (vs No verified drop-in alternative)
- Concurrent full-line-rate port operation (vs No verified drop-in alternative)
設計ノート
Treat every PCIe link as a controlled-impedance differential transmission line. Route the PEX8605-AB50NI differential pairs over a continuous reference plane, keep pair geometry matched, minimize vias and stubs, and avoid plane splits beneath the links. Validate the 136-aQFN escape routing and any connector or cable transition with PCIe channel analysis.
Follow the manufacturer’s power-plane, decoupling, and sequencing recommendations for the switch and connected PCIe endpoints. Place local high-frequency decoupling close to the relevant package pins, provide a low-impedance return path, and avoid powering endpoint devices before the switch and host rails are stable. Confirm voltage tolerances and sequencing requirements from the complete manufacturer datasheet.
The 136-aQFN package has fine-pitch contacts that require the manufacturer land pattern, mask and paste recommendations, and adequate thermal-via design around the exposed pad. Review PCB assembly capability for this package before committing to a design. Keep high-speed differential routes away from switching-regulator loops and provide clean partitioning between PCIe, power, and sensitive external interfaces.
Do not treat a switch with the same port count as a drop-in replacement without verifying the complete pinout, reference clocks, power rails, PCIe generation, lane routing, reset inputs, firmware, and exposed-pad connection. The verified cross-reference information identifies no separately validated drop-in substitute for the PEX8605-AB50NI. A PCB redesign is required for any differently packaged or materially different switch.
コンプライアンス情報
No explicit compliance declarations are identified in the manufacturer architecture page or distributor snippets. The device is an industrial and embedded PCIe switch rather than an automotive-qualified AEC-Q100 product.