PIC12F683-E/MF - 8-Bit 20MHz Flash MCU | Microchip
部品番号: PIC12F683-E/MF ✓ 生産中PIC12F683-E/MF 概要
A flash-based microcontroller is a semiconductor that stores its programmed instructions in electrically erasable and reprogrammable nonvolatile memory. The PIC12F683 belongs to the PIC12 low-pin-count family and combines a small RISC instruction set, integrated data memory, on-board EEPROM, and mixed-signal sensing resources in a limited pin-count package. This combination makes it useful where board area, voltage range, and deterministic control are more important than high computational throughput.
Key features include an 8-bit processing core operating up to 20 MHz, 3.5 KB of flash program memory, 128 bytes of RAM, and a 4-channel 10-bit ADC. The six available I/O pins can support digital control, serial communication, status indication, and analog input multiplexing. On-board EEPROM allows calibration values, configuration parameters, counters, and operating-state information to be retained when power is removed without adding a separate memory component.
The PIC12F683-E/MF architecture is designed around the mid-range enhanced mid-range PIC core and its 14-bit instruction word organization. Although the family includes a larger 8K × 14 program-memory address space, only 2K × 14 words are physically implemented in this device. A 10-bit ADC provides four analog channels, while the operating range of 2.0 V to 5.5 V permits use in both 3.3 V and 5 V systems when the associated peripherals and timing are configured appropriately.
Typical applications include compact industrial controllers, building automation modules, appliance-control boards, battery-powered instruments, sensor interfaces, LED-control circuits, and low-cost embedded products. Its small 8-DFN-S footprint is especially useful when the enclosure provides little board area and the design can accommodate the package's exposed-pad and assembly requirements.
Layout and firmware planning should treat the ADC, oscillator configuration, unused pins, and exposed thermal pad as one integrated design task. Place input and output decoupling capacitors close to their supply pins, route analog inputs away from fast-switching nodes, and verify the assembled board against the manufacturer datasheet's pin and layout guidance.
This product page combines the exact PIC12F683-E/MF electrical identity, package information, programming considerations, qualified same-family alternatives, and practical design guidance into a compact engineering reference for initial design review and sourcing.
ドロップイン代替品: PIC12F683-E/MF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC12F683-E/MF (同一形状・フットプリント) — 相違点: Maximum CPU Frequency, Mounting Type, Package.
PIC12F683-I/MF
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
PIC12F683-E/MF 最大定格&電気的特性
| Microcontroller Type | 8-bit CMOS flash microcontroller |
| Maximum CPU Frequency | 20 MHz |
| Program Memory | 3.5 KB (2K × 14 words) |
| Program Counter Address Space | 8K × 14 words, with 2K × 14 words physically implemented |
| RAM | 128 bytes |
| EEPROM Data Memory | 256 bytes |
| General-Purpose I/O | 6 pins |
| Operating Voltage Range | 2.0 V to 5.5 V |
| ADC Resolution | 10 bits |
| ADC Channels | 4 channels |
| Program Memory Type | Flash |
| Architecture | Enhanced mid-range PIC architecture |
| Instruction Word Size | 14 bits |
| パッケージ | 8-DFN-S (6 × 5 mm) |
| 実装タイプ | Surface mount |
| ピン数 | 8 pins |
| Power-Saving Technology | nanoWatt Technology |
PIC12F683-E/MF 8-dfn-s (6 × 5 mm) ピン配置ガイド
PIC12F683-E/MF (8-dfn-s (6 × 5 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: PIC12F683-E/MF.
詳細は データシート をご参照ください。
主な用途
PIC12F683-E/MF の用途: 6 件s: Compact Industrial Sensor Interface, Battery-Powered Environmental Monitor, Appliance Control Module, Building Automation Endpoint, LED Status and Lighting Controller, Compact Measurement and Control Board.
Compact Industrial Sensor Interface
The PIC12F683-E/MF fits compact industrial sensor interfaces because it combines a four-channel 10-bit ADC with six I/O pins in an 8-DFN-S package measuring 6 × 5 mm. The 2.0 V to 5.5 V operating range supports low-voltage sensor subsystems, while 128 bytes of RAM provides working space for sampled values and control state. Its 256-byte EEPROM can retain calibration constants or configuration parameters between power cycles. Place the ADC inputs away from switching-power traces, use a quiet ground reference, and validate the acquisition timing against the four-channel multiplexer configuration before treating the sensor readings as production-accurate.
おすすめ
Battery-Powered Environmental Monitor
The PIC12F683-E/MF is appropriate for battery-powered environmental monitors where low pin count, EEPROM retention, and mixed-signal measurement are valuable. It samples up to four analog channels with a 10-bit ADC, operates from 2.0 V to 5.5 V, and provides 128 bytes of RAM for measurement state. The 256-byte EEPROM can store calibration offsets or interval counters without continuous power consumption from volatile memory. Because the implemented code space is 2K × 14 words, firmware must remain compact, and sleep-mode behavior should be tested with the actual sensor and radio load to determine the attainable battery interval.
おすすめ
Appliance Control Module
The PIC12F683-E/MF can serve as the control hub in a compact appliance module by combining flash-based firmware, six I/O pins, and on-board EEPROM in a small 8-DFN-S outline. The microcontroller can supervise relays, indicators, buttons, and analog feedback while retaining operating counters or service configuration in EEPROM. Its 20 MHz maximum clock provides timing headroom for typical control loops, and the 2.0 V to 5.5 V range accommodates multiple low-voltage supply schemes. For mains-connected appliances, isolate the low-voltage control domain from hazardous energy and validate every protection barrier independently of the microcontroller selection.
おすすめ
Building Automation Endpoint
The PIC12F683-E/MF is suitable for a low-cost building-automation endpoint that reads environmental inputs and controls discrete outputs. Six I/O pins can handle switches, alarm signals, relay drive, or status LEDs, while the four-channel 10-bit ADC can monitor temperature, light, or occupancy-sensor analog outputs. Flash permits firmware updates, and EEPROM supports persistent configuration such as thresholds, calibration factors, or endpoint identity. The main engineering constraints are the 2K × 14-word implemented program space and the small package footprint, so prioritize peripheral features according to actual firmware demand and maintain adequate copper and thermal-pad support during assembly.
おすすめ
LED Status and Lighting Controller
The PIC12F683-E/MF can control LED status indicators or simple lighting functions where a compact controller and limited I/O are sufficient. Its six I/O pins can drive indicator logic or external transistor stages, and flash memory allows firmware-defined blink patterns and timing behavior. The 20 MHz clock capability provides ample timing margin for multiplexing, fault indication, and basic dim-control algorithms based on software timers. Use appropriate transistor drive and current limiting rather than exceeding GPIO limits directly. If the LED driver introduces high di/dt transitions, keep those return currents away from the ADC reference and sensitive sensor paths to prevent coupling into measured signals.
おすすめ
Compact Measurement and Control Board
The PIC12F683-E/MF supports compact measurement-and-control boards that must combine analog input measurement, local logic, and nonvolatile configuration in a limited board area. Its four-channel 10-bit ADC, 128 bytes of RAM, 256-byte EEPROM, and six I/O pins provide a compact mixed-signal control platform. The 2.0 V minimum operating voltage supports reduced-energy designs, while the 3.5 KB flash capacity accommodates moderate control firmware. Validate the ADC reference, input filtering, and settling time on the assembled PCB, and leave programming access for firmware updates and calibration without consuming scarce I/O pins unnecessarily.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC12F683-E/MF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC12F683-I/MF |
|---|---|---|
| Package | 8-DFN-S (6 × 5 mm) | 8-DFN-S (6 × 5 mm) - same footprint |
| Brand | Microchip Technology | Microchip Technology |
| CPU Architecture | 8-bit PIC | 8-bit PIC |
| Maximum CPU Frequency | 20 MHz | 20 MHz |
| Program Memory | 3.5 KB (2K × 14 words) | 3.5 KB (2K × 14 words) |
| RAM | 128 bytes | 128 bytes |
| EEPROM Data Memory | 256 bytes | 256 bytes |
| General-Purpose I/O | 6 pins | 6 pins |
| Operating Voltage Range | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| ADC | 4-channel, 10-bit | 4-channel, 10-bit |
| Temperature-Grade Ordering Option | -E/MF | -I/MF; exact temperature limits require confirmation |
主な差別化要因
- Combines mixed-signal control with a compact 8-DFN-S footprint (vs PIC12F683-I/MF)
- Supports low-voltage operation without an external regulator requirement stated for the device (vs PIC12F683-I/MF)
- Provides persistent parameter storage in a small pin-count package (vs PIC12F683-I/MF)
設計ノート
Reserve the exposed-pad and copper area required by the 8-DFN-S assembly guidance in Microchip datasheet 41211B. Place the device-side supply capacitor adjacent to VDD and GND, route analog inputs away from switching nodes, and keep programming-interface access available for manufacturing. Validate the land pattern and exposed-pad connection against the package drawing rather than a generic DFN footprint.
Design the supply rail for the full 2.0 V to 5.5 V operating range while accounting for GPIO injection limits, ADC reference accuracy, and peripheral current at 20 MHz. Place bulk and high-frequency bypass capacitance according to the manufacturer layout recommendations. If the source rail can overshoot or fall outside the permitted range, add suitable protection rather than relying on software to detect an invalid supply condition.
Do not treat the nominal 8K × 14 program-memory address space as implemented flash. The PIC12F683-E/MF physically implements only 2K × 14 words, so compile the final firmware with the correct device definition and verify its size before programming. Also use the package-specific pin table rather than a generic 8-pin diagram, and confirm the configuration words required by the intended clock, watchdog, and brownout behavior.
For analog measurements, keep sensor traces short and connect the ADC return to the appropriate quiet ground reference. Place input filtering close to the MCU pins and assess the source impedance against the ADC acquisition requirements. A four-channel 10-bit ADC does not eliminate noise or settling-time concerns; the measured accuracy depends on reference stability, layout, sampling time, and the external sensor interface.
コンプライアンス情報
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact ordering code.