PIC16C54C-20I/SS - 8-bit 20MHz OTP MCU, 12 I/O, SSOP-20
部品番号: PIC16C54C-20I/SS ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $2.6319 | $2.63 |
| 10 | $2.45 | $24.50 |
| 100 | $2.18 | $218.00 |
| 500 | $1.95 | $975.00 |
| 1,000 | $1.74 | $1,740.00 |
PIC16C54C-20I/SS 概要
What is a PIC16C5x microcontroller? An 8-bit microcontroller is a small computer-on-a-chip integrating a CPU, RAM, program memory, and peripherals on a single die. The PIC16C5x family uses a Harvard RISC architecture with separate program and data buses, a 12-bit wide instruction word, and a small fixed instruction set of 33 single-word, single-cycle instructions, enabling deterministic execution and very low power consumption. This hierarchy places the PIC16C54C in the broader taxonomy of microcontroller -> embedded controller -> semiconductor, and the 'C' OTP variant is the most modern, lowest-cost member of the original PIC16C5x line.
Key features include a two-level deep hardware call stack, direct/indirect/relative addressing modes, an 8-bit real-time clock/counter (TMR0) with an 8-bit programmable prescaler, power-on reset (POR), a Watchdog Timer (WDT) with its own on-chip RC oscillator, and an internal/external oscillator option. The device operates from 4.5V to 5.5V and supports both internal RC and external crystal/RC oscillator configurations, with selectable oscillator types.
Architecturally, the PIC16C54C uses a fully static CMOS design and the PIC mid-range core (12-bit instructions, 8-bit data path). Seven or eight special-function hardware registers control I/O and core operation. Because of its small footprint, low pin count, and deterministic core, it excels in cost-sensitive 8-bit embedded applications that do not need interrupts or a deep stack.
Typical applications include simple appliance controls, battery chargers, LED lighting controllers, sensor signal conditioning, automotive body electronics, and low-cost consumer devices. The SSOP-20 package (0.209 inch / 5.30 mm body width) supports compact PCB designs. Note that the PIC16C54C does not feature interrupts, so polling-based firmware is required.
Design consideration: this part is OTP (One-Time Programmable), so code must be fully verified before committing - there is no in-circuit reprogramming. For prototyping or field-upgradable designs, consider the PIC16F54 Flash-based equivalent in the same SSOP-20 footprint.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a bare manufacturer product page.
ドロップイン代替品: PIC16C54C-20I/SS — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C54C-20I/SS （同一形状・フットプリント） — 相違点: Package, Program Memory Size, Timers, Program Memory Type, Operating Temperature.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16F54-I/SS
✅ ドロップイン✓ 在庫あり
$0.68 / 個
データシートを見る →PIC16C54A-20I/SS
✅ ドロップイン✓ 在庫あり
$2.51 / 個
データシートを見る →PIC16C54C-04I/SS
✅ ドロップイン✓ 在庫あり
$1.34 / 個
データシートを見る →PIC16C54C-20I/SS 最大定格＆電気的特性
| Core Architecture | 8-bit PIC RISC |
| Core Size | 8-bit data path, 12-bit instructions |
| 最大クロック周波数 | 20 MHz |
| Program Memory Size | 768 B (512 x 12) OTP |
| RAM Size | 25 B |
| Number of I/O Pins | 12 |
| 電源電圧 | 4.5 V to 5.5 V |
| 動作温度 | -40 C to +85 C (Industrial) |
| パッケージ | 20-SSOP (0.209 inch, 5.30 mm body width) |
| 実装タイプ | Surface Mount |
| Oscillator Type | External or Internal RC |
| Timers | 1 x 8-bit (TMR0) with 8-bit prescaler |
| Peripherals | POR, WDT |
| Connectivity | None (standalone) |
| Data Converters | None |
| Program Memory Type | OTP EPROM |
| MSLレベル | 1 (unlimited) |
| Lead-Free / RoHS | Compliant per Microchip product page |
PIC16C54C-20I/SS ピン構成
| ピン 1 | RA2 — Bidirectional I/O port A bit 2 |
| ピン 2 | RA3 — Bidirectional I/O port A bit 3 |
| ピン 3 | RTCC — Real-time clock/counter TMR0 input (also RA0) |
| ピン 4 | MCLR — Master clear reset (active low) |
| ピン 5 | VSS — Ground reference |
| ピン 6 | RB0 — Bidirectional I/O port B bit 0 |
| ピン 7 | RB1 — Bidirectional I/O port B bit 1 |
| ピン 8 | RB2 — Bidirectional I/O port B bit 2 |
| ピン 9 | RB3 — Bidirectional I/O port B bit 3 |
| ピン 10 | RB4 — Bidirectional I/O port B bit 4 |
| ピン 11 | RB5 — Bidirectional I/O port B bit 5 |
| ピン 12 | RB6 — Bidirectional I/O port B bit 6 |
| ピン 13 | RB7 — Bidirectional I/O port B bit 7 |
| ピン 14 | VSS — Ground reference (secondary) |
| ピン 15 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| ピン 16 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| ピン 17 | RA0 — Bidirectional I/O port A bit 0 |
| ピン 18 | RA1 — Bidirectional I/O port A bit 1 |
| ピン 19 | VDD — Positive supply voltage (4.5V to 5.5V) |
| ピン 20 | VDD — Positive supply voltage (4.5V to 5.5V, secondary) |
主な用途
PIC16C54C-20I/SS の用途: 6 件s: Appliance Control Boards, LED Lighting Controllers, Battery Chargers, Sensor Signal Conditioning, Automotive Body Electronics, Consumer Electronics Toys.
Appliance Control Boards
The PIC16C54C-20I/SS suits low-cost appliance control (washing machines, microwave user interfaces, fans) where deterministic polled firmware, 12 digital I/O, and OTP cost optimization matter more than interrupts. At 20 MHz, the core executes one instruction per cycle, comfortably timing relay de-bounce, button scanning, and 7-segment multiplexing without DMA. The SSOP-20 footprint (5.30 mm body) supports tight main-control PCB layouts. Compared with PIC16F877A, the C54C drops ADC/EUSART but cuts unit cost ~30% for I/O-bound applications.
おすすめ
LED Lighting Controllers
LED driver and dimmer controllers benefit from the PIC16C54C-20I/SS's 12 I/O, hardware WDT, and industrial -40C to +85C temperature grade. The 20 MHz core generates accurate PWM via firmware toggles for triac-dimmable mains LED lamps. OTP memory locks the dimming curve, preventing field tampering and reverse engineering - a regulatory plus for safety-critical SSL products. SSOP-20 keeps the BOM compact inside lamp bases. Pair with a TRIAC driver and zero-cross detector for phase-angle dimming.
おすすめ
Battery Chargers
Simple lead-acid or NiMH chargers use the PIC16C54C-20I/SS for voltage/current loop control via the 8-bit TMR0 and firmware ADC by sigma-delta on a digital I/O pin. The 4.5V to 5.5V supply matches USB or wall-adapter rails, and the WDT guards against firmware lockup. OTP ensures the charge algorithm cannot be corrupted by voltage transients on the DC bus. Polled execution suffices because the charge cycle is intentionally slow (hours), so no interrupts are needed.
おすすめ
Sensor Signal Conditioning
Cost-sensitive sensor front-ends (thermistor bridges, simple PIR motion detectors, reed-switch debouncers) use the PIC16C54C-20I/SS as a low-cost digital filter. Polled firmware implements moving-average filtering of a comparator-based sigma-delta ADC on one I/O pin. The 20 MHz clock handles ~5 MIPS, enough for 10 Hz update rates on 4-8 sensors. Industrial temperature grade suits outdoor and HVAC installations, while OTP locks calibration coefficients.
おすすめ
Automotive Body Electronics
Inside-cabin automotive accessories (window timers, mirror controllers, simple alarm indicators) historically used the PIC16C54C-20I/SS because the -40C to +85C industrial grade survives the cabin environment and OTP locks the BOM. 12 I/O drive LEDs, relays, and switches directly. Note: for under-hood AEC-Q100 applications, upgrade to the PIC16F54-I/SS or PIC16F18313-I/SN (AEC-Q100 qualified) - the C54C lacks automotive qualification by design.
おすすめ
Consumer Electronics Toys
Mass-market toys, novelty items, and educational kits use the PIC16C54C-20I/SS because OTP delivers the lowest possible unit cost (<USD 1.75 at qty 1000) while the 20 MHz core animates LEDs, drives buzzers, and sequences servo motors. 25 B RAM accommodates small lookup tables for sound effects; 768 B OTP holds simple state-machine firmware. SSOP-20 supports tiny PCBs inside handheld enclosures. Polled firmware is acceptable because toy loops are inherently short.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C54C-20I/SS — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16F54-I/SS | PIC16C54A-20I/SS | PIC16C54C-04I/SS | PIC16C54C-20I/P | PIC16C54C-20I/SO |
|---|---|---|---|---|---|---|
| Package | 20-SSOP (0.209 inch / 5.30 mm) | 20-SSOP - same | 20-SSOP - same | 20-SSOP - same | 20-PDIP - different footprint | 20-SOIC - different footprint |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Max Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 4 MHz | 20 MHz | 20 MHz |
| Program Memory | 768 B OTP | 768 B Flash | 768 B OTP | 768 B OTP | 768 B OTP | 768 B OTP |
| RAM Size | 25 B | 25 B | 25 B | 25 B | 25 B | 25 B |
| I/O Pins | 12 | 12 | 12 | 12 | 12 | 12 |
| Supply Voltage | 4.5 V to 5.5 V | 2.0 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Memory Type | OTP EPROM (one-time programmable) | Flash (reprogrammable) | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM |
| Interrupts | None (polled only) | None (polled only) | None (polled only) | None (polled only) | None (polled only) | None (polled only) |
主な差別化要因
- OTP EPROM allows code-locked mass production at lowest unit cost （vs PIC16F54-I/SS)
- Industrial temperature grade for harsh environments （vs PIC16C54C-20/P (commercial grade, 0C to +70C))
- True drop-in upgrade to Flash memory via PIC16F54-I/SS （vs PIC16F54-I/SS)
設計ノート
Estimated: SSOP-20 thermal pad is the VSS pin (pin 5/14) - tie both VSS pins to a contiguous ground pour. Route MCLR (pin 4) with a 10 kohm pull-up to VDD and a 100 nF cap to VSS for noise-free reset. Place a 100 nF decoupling cap within 5 mm of VDD pins 19/20 and a 10 uF bulk cap on the same supply node. SSOP-20 land pattern requires 0.65 mm pitch traces.
Estimated: OTP memory can be programmed only once - the programmer (e.g., MPLAB PICkit 3/4) verifies each word after writing. Any verification failure means the silicon is dead. Always pre-test firmware on a PIC16F54-I/SS (Flash drop-in) and only commit to OTP for the production run. Also note the PIC16C5x core has NO hardware interrupts - a missed event in polled firmware becomes a permanent bug if not handled by the WDT reset path.
The PIC16C54C-20I/SS supports LP, XT, HS, and RC oscillator modes selected by configuration bits. For 20 MHz operation, HS mode with a 20 MHz crystal and two 15-33 pF load capacitors is mandatory - XT mode is limited to 4 MHz. For cost-sensitive designs below 4 MHz, the internal 4 MHz RC oscillator (configurable) eliminates the crystal entirely. Always include a 1 Mohm resistor across OSC1/OSC2 if using a low-drive crystal to prevent overdrive.
コンプライアンス情報
RoHS and lead-free per Microchip product page. The PIC16C54C family is NOT AEC-Q100 qualified; for automotive cabin/body electronics that need formal qualification, use PIC16F54-I/SS or a PIC16F1xx AEC-Q100 part instead.
