PIC16C63AT-04I/SS - 8-bit MCU, 7KB OTP, 4MHz, 28-SSOP | Microchip
部品番号: PIC16C63AT-04I/SS ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $7.92 | $7.92 |
| 10 | $7.13 | $71.30 |
| 100 | $6.34 | $634.00 |
| 500 | $5.71 | $2,855.00 |
| 1,000 | $5.08 | $5,080.00 |
PIC16C63AT-04I/SS 概要
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces onto one silicon die. The PIC16CXX mid-range family is built on a fully-static CMOS architecture and belongs to the broader 8-bit microcontroller category, which sits within embedded computing, microcontrollers, and finally integrated circuits. These devices are engineered for deterministic real-time control where predictable instruction timing, low cost, and ease of development outweigh raw computational throughput.
Key features of the PIC16C63AT-04I/SS include its 4MHz maximum clock, 192 x 8 bytes of data RAM, 22 digital I/O pins, and integrated peripherals such as a USART for serial communication, a Capture/Compare/PWM module, an 8-bit timer/counter, and a watchdog timer for reliable operation in noise-prone industrial environments. The OTP program memory allows one-time field programming, making the device well-suited for mature production designs where firmware is finalized.
Technically, the PIC16C63A employs a RISC-style Harvard architecture with separate program and data buses, providing predictable instruction execution in a single instruction cycle (four clock periods). This makes interrupt response and timing calculations straightforward for embedded developers writing in assembly or C. The 4MHz clock yields a 1-microsecond instruction cycle, sufficient for many sensing, motor, and human-machine-interface tasks.
Typical applications include industrial control subsystems, appliance control boards, sensor signal conditioners, simple sensor hubs, and embedded user-interface modules where cost-sensitive, deterministic 8-bit control is required. The 28-SSOP footprint also makes it attractive for space-constrained PCB designs.
When designing with this device, ensure the 5V supply is well-decoupled with a 100nF ceramic capacitor close to VDD, and configure the MCLR pin with the recommended 10kohm pull-up for clean device reset behavior.
This page synthesizes current distributor inventory, parametric drop-in alternatives, and engineering design notes not found in the standalone manufacturer datasheet.
ドロップイン代替品: PIC16C63AT-04I/SS — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C63AT-04I/SS （同一形状・フットプリント） — 相違点: Package, Instruction Set, Operating Temperature, Core Architecture, Timers.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C63A-04I/SS
✅ ドロップイン✓ 在庫あり
$5.55 / 個
データシートを見る →PIC16C63A-20I/SS
✅ ドロップイン✓ 在庫あり
$4.4 / 個
データシートを見る →PIC16C62B-04I/SS
✅ ドロップイン✓ 在庫あり
$5.4 / 個
データシートを見る →PIC16C63AT-04I/SS 最大定格＆電気的特性
| Manufacturer | Microchip Technology |
| Series | PIC 16C |
| Core Processor | PIC |
| Core Size | 8-bit |
| Program Memory Size | 7 KB (4K x 14) OTP |
| RAM Size | 192 x 8 bytes |
| Number of I/O | 22 |
| 最大クロック周波数 | 4 MHz |
| Instruction Cycle | 1 us (4 clock periods) |
| 動作温度 | -40C to +85C (Industrial) |
| パッケージ | 28-SSOP (0.209", 5.30mm Width) |
| 実装タイプ | Surface Mount |
| Peripherals | USART, CCP, Timer, WDT, POR |
| Program Memory Type | OTP (One-Time Programmable) |
PIC16C63AT-04I/SS ピン構成
| ピン 1 | MCLR — Master Clear (reset) input; tie to VDD via 10kohm pull-up |
| ピン 2 | RA0 — PORTA digital I/O bit 0 |
| ピン 3 | RA1 — PORTA digital I/O bit 1 |
| ピン 4 | RA2 — PORTA digital I/O bit 2 |
| ピン 5 | RA3 — PORTA digital I/O bit 3 |
| ピン 6 | RA4 — PORTA digital I/O bit 4 (open-drain option) |
| ピン 7 | RA5 — PORTA digital I/O bit 5 |
| ピン 8 | VSS — Ground reference |
| ピン 9 | OSC1 — Crystal/oscillator input |
| ピン 10 | OSC2 — Crystal/oscillator output |
| ピン 11 | RC0 — PORTC digital I/O bit 0 / T1OSO |
| ピン 12 | RC1 — PORTC digital I/O bit 1 / T1OSI |
| ピン 13 | RC2 — PORTC digital I/O bit 2 / CCP1 |
| ピン 14 | RC3 — PORTC digital I/O bit 3 / SCL |
| ピン 15 | RC4 — PORTC digital I/O bit 4 / SDA |
| ピン 16 | RC5 — PORTC digital I/O bit 5 / SDO |
| ピン 17 | RC6 — PORTC digital I/O bit 6 / TX |
| ピン 18 | RC7 — PORTC digital I/O bit 7 / RX |
| ピン 19 | VSS — Ground reference |
| ピン 20 | VDD — Positive supply voltage |
| ピン 21 | RB0 — PORTB digital I/O bit 0 / INT |
| ピン 22 | RB1 — PORTB digital I/O bit 1 |
| ピン 23 | RB2 — PORTB digital I/O bit 2 |
| ピン 24 | RB3 — PORTB digital I/O bit 3 |
| ピン 25 | RB4 — PORTB digital I/O bit 4 |
| ピン 26 | RB5 — PORTB digital I/O bit 5 |
| ピン 27 | RB6 — PORTB digital I/O bit 6 / PGC |
| ピン 28 | RB7 — PORTB digital I/O bit 7 / PGD |
主な用途
PIC16C63AT-04I/SS の用途: 6 件s: Industrial Sensor Hub, Appliance Control Board, HMI Keypad and Display Module, Automotive Interior Accessory Controller, Smart Sensor Node with UART Bridge, Legacy Industrial Module Replacement.
Industrial Sensor Hub
The PIC16C63AT-04I/SS fits industrial sensor hub designs because its 22 I/O pins can interface multiple analog and digital sensors, while the integrated USART enables reliable RS-232 or RS-485 backhaul. Its 4MHz clock and 1us instruction cycle are fast enough for periodic scanning of temperature, pressure, and flow sensors at sub-100ms intervals. The industrial -40C to +85C range ensures operation in factory cabinets. Place a 100nF ceramic decoupling capacitor close to VDD to keep the analog references stable when switching loads.
おすすめ
Appliance Control Board
For appliance controllers (washing machines, dishwashers, microwave ovens), the PIC16C63AT-04I/SS provides the deterministic control loop timing required for motor PWM and user-interface scanning. The CCP module generates PWM for motor or heater control, while the watchdog timer recovers from power-line transients common in household mains environments. The 28-SSOP footprint allows compact board designs beneath control panels. Use the MCLR pull-up recommended in the Microchip datasheet to ensure clean brown-out recovery.
おすすめ
HMI Keypad and Display Module
The PIC16C63AT-04I/SS can drive character LCDs and matrix keypads in cost-sensitive human-machine-interface modules. Its 22 I/O pins easily accommodate a 4x4 keypad plus LCD data bus, while the 192-byte RAM supports button debouncing and menu state machines. The OTP memory is appropriate because UI firmware is typically frozen before production. Use the CCP module to generate a software-driven contrast PWM for the LCD.
おすすめ
Automotive Interior Accessory Controller
In non-safety automotive interior accessories (ambient lighting, seat controllers, mirror adjusters), the PIC16C63AT-04I/SS offers sufficient I/O count and timing resolution for PWM dimming and switch debouncing. Designers should note that AEC-Q100 qualification is NOT documented for this part; for safety-critical or AEC-Q100-mandated systems, choose a PIC16F equivalent qualified to automotive standards. The industrial -40C to +85C range covers most cabin environments.
おすすめ
Smart Sensor Node with UART Bridge
For remote sensor nodes bridged to a host controller via UART, the PIC16C63AT-04I/SS performs local sampling and pre-processing before forwarding formatted packets. Its hardware USART simplifies command/response protocol implementation, while the 7KB OTP is ample for typical sensor-fusion code. The 4MHz clock keeps power consumption low for battery or line-powered nodes; the 28-SSOP package enables compact board placement near the sensor head.
おすすめ
Legacy Industrial Module Replacement
The PIC16C63AT-04I/SS is well-suited to sustaining production of legacy industrial modules that already have a validated firmware base. Its pin-compatible PIC16C63A-04I/SS and -20I/SS siblings provide drop-in alternatives when original parts are out of stock. The OTP memory is acceptable when firmware revisions are infrequent and traceability is maintained. Designers should plan a migration path to flash-based PIC16F parts for long-term product lifecycle support.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C63AT-04I/SS — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C63A-04I/SS | PIC16C63A-20I/SS | PIC16C62B-04I/SS |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Core | 8-bit PIC mid-range | 8-bit PIC mid-range | 8-bit PIC mid-range | 8-bit PIC mid-range |
| Program Memory | 7 KB OTP | 7 KB OTP | 7 KB OTP | 3.5 KB OTP |
| RAM | 192 bytes | 192 bytes | 192 bytes | 128 bytes |
| Max Clock Frequency | 4 MHz | 4 MHz | 20 MHz | 4 MHz |
| Number of I/O | 22 | 22 | 22 | 22 |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete |
主な差別化要因
- Higher clock frequency option in identical package （vs PIC16C63A-04I/SS)
- Larger RAM and program memory vs smaller PIC16C62B （vs PIC16C62B-04I/SS)
- Tape-and-reel packaging for high-volume SMT assembly （vs PIC16C63A-04I/SS (tube))
設計ノート
Decouple VDD with a 100nF ceramic capacitor placed within 5mm of the VDD pin (pin 20), and place a bulk capacitor of at least 10uF near the supply entry point. The PIC16C63A family is sensitive to VDD ripple during oscillator start-up; insufficient decoupling can cause intermittent POR events and corrupted EEPROM/OTP write cycles. Estimated: at 4MHz and 5V supply with all I/O toggling at 50% duty, the device draws approximately 5-10 mA active current.
Route the oscillator traces (OSC1 pin 9, OSC2 pin 10) short and direct, with a ground guard ring if possible. Keep high-speed switching traces (CCP PWM outputs, USART lines) away from the crystal traces to prevent injection of noise that can shift the clock frequency or cause spurious resets. The 28-SSOP package has a center thermal pad on some variants; refer to the datasheet to confirm whether thermal pad soldering is required for your specific pinout revision.
Do not assume the PIC16C63A pinout is interchangeable with the PIC16F648A or PIC16F73 families despite identical 28-SSOP package; the I/O mapping and peripheral assignments differ in several positions. Always cross-reference the MCLR pin location and ensure a 10kohm pull-up to VDD is present. Estimated: omitting the MCLR pull-up causes intermittent reset behavior in electrically noisy industrial environments such as motor-drive cabinets.
コンプライアンス情報
RoHS and lead-free status not explicitly documented in the Verified Web Data; the original PIC16C63A family predates widespread RoHS adoption but Microchip transitioned legacy OTP parts where possible. AEC-Q100 automotive qualification is NOT documented for this part. Conflict-minerals compliance assumed compliant per Microchip corporate policy but specific declaration not in provided data.
