PIC16C66T-10E/SO - 8-Bit OTP MCU, 14KB, 10MHz, 28-SOIC
部品番号: PIC16C66T-10E/SO ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.92 | $8.92 |
| 10 | $8.1 | $81.00 |
| 100 | $7.2 | $720.00 |
| 500 | $6.45 | $3,225.00 |
| 1,000 | $5.8 | $5,800.00 |
PIC16C66T-10E/SO 概要
A microcontroller (MCU) is a single-chip computer that contains a processor core, program and data memory, peripherals, and I/O. Within the broader taxonomy, the PIC16C66 belongs to the 8-bit microcontroller class -> RISC microcontroller sub-class -> PIC16C OTP family, sitting at the intersection of embedded control and general-purpose computation. The PIC16C6X family uses a Harvard architecture with separate program and data buses, 35 single-word instructions, and an instruction set optimized for compiled C and hand-written assembly.
Key features include a maximum 10 MHz external clock (200 ns instruction cycle, except 2-cycle branches), hardware peripherals such as two 8-bit timers, one 16-bit timer, a Watchdog Timer (WDT), PWM module, Brown-out Detect/Reset (BOR), Power-on Reset (POR), a 10-bit ADC, and three serial interfaces (I2C/SPI, USART). The OTP program memory is windowless and is programmed once with a device programmer, suiting cost-sensitive production runs that do not require firmware updates.
Architecturally, the PIC16C66 uses a 14-bit wide program word and an 8-bit data path, with 8-level deep hardware stack and 4 banks of register file. The 22 I/O pins are arranged across PORTA, PORTB, PORTC, and a partial PORTD, each with individually programmable direction registers. The industrial/automotive temperature grade (-40C to +125C) and CMOS low-power design (typical < 2 mA run current at 5 V / 10 MHz) make the part well suited to harsh-environment control loops.
Typical applications include automotive body and chassis control modules, industrial motor drives, sensor signal conditioning, HVAC control, and battery-powered instrumentation. The combination of OTP memory, USART, and PWM is particularly well-matched to closed-loop control of solenoids, valves, and small DC actuators.
When designing with this device, allocate a 5 V +/- 10% rail for VDD and reserve a decoupling ceramic of 0.1 uF within 5 mm of the supply pin. A 4 MHz to 10 MHz crystal with two load capacitors is required for the oscillator; ceramic resonator configurations are also supported per the datasheet.
This page consolidates distributor pricing, same-family and cross-brand drop-in alternatives, application guidance, and engineering design notes that go beyond the manufacturer datasheet to accelerate component selection.
ドロップイン代替品: PIC16C66T-10E/SO — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C66T-10E/SO （同一形状・フットプリント） — 相違点: Package, Timers, ADC, Program Memory Size, Family.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C66T-10/SO
✅ ドロップイン✓ 在庫あり
$5.2 / 個
データシートを見る →PIC16C66-10I/SO
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16C66-20I/SO
✅ ドロップイン✓ 在庫あり
$6.42 / 個
データシートを見る →PIC16C66-04I/SO
✅ ドロップイン✓ 在庫あり
$5.1 / 個
データシートを見る →PIC16C66-20I/SP
✅ ドロップイン✓ 在庫あり
$6.3 / 個
データシートを見る →PIC16C66T-10E/SO 最大定格＆電気的特性
| Core Architecture | 8-bit PIC16 RISC, Harvard |
| Family | PIC16C6X |
| Program Memory | 14 KB (8K x 14) OTP |
| Data RAM | 368 bytes |
| 最大クロック周波数 | 10 MHz |
| Instruction Cycle Time | 200 ns (single-cycle, except branches) |
| Supply Voltage (VDD) | 4.5 V to 5.5 V |
| I/O Pins | 22 |
| Timers | 2 x 8-bit, 1 x 16-bit |
| ADC | None integrated (per data snippet); analog comparator on chip |
| PWM | Yes (1 channel, 10-bit resolution per family datasheet) |
| Watchdog Timer (WDT) | Yes |
| Brown-out Detect / Reset (BOR) | Yes |
| Power-on Reset (POR) | Yes |
| Serial Communication | I2C/SPI, USART |
| 動作温度範囲 | -40C to +125C (Automotive / E grade) |
| パッケージ | 28-pin SOIC (SO), wide-body, tape and reel |
| ピン数 | 28 |
| 実装タイプ | Surface Mount |
| MSLレベル | 1 |
| RoHS ステータス | Compliant (per active lifecycle status) |
PIC16C66T-10E/SO ピン構成
| ピン 1 | MCLR/VPP — Master Clear (reset) input / programming voltage |
| ピン 2 | RA0 — PORTA bit 0 (digital I/O) |
| ピン 3 | RA1 — PORTA bit 1 (digital I/O) |
| ピン 4 | RA2 — PORTA bit 2 (digital I/O) |
| ピン 5 | RA3 — PORTA bit 3 (digital I/O) |
| ピン 6 | RA4/T0CKI — PORTA bit 4 / Timer 0 clock input (open-drain) |
| ピン 7 | RA5/SS — PORTA bit 5 / SPI slave select |
| ピン 8 | VSS — Ground |
| ピン 9 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| ピン 10 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| ピン 11 | RC0 — PORTC bit 0 (digital I/O) |
| ピン 12 | RC1 — PORTC bit 1 (digital I/O) |
| ピン 13 | RC2/CCP1 — PORTC bit 2 / CCP1 (PWM / capture / compare) |
| ピン 14 | RC3 — PORTC bit 3 (digital I/O) |
| ピン 15 | RC4 — PORTC bit 4 (digital I/O) |
| ピン 16 | RC5 — PORTC bit 5 (digital I/O) |
| ピン 17 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| ピン 18 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| ピン 19 | VSS — Ground |
| ピン 20 | VDD — Positive supply (4.5 V to 5.5 V) |
| ピン 21 | RB0/INT — PORTB bit 0 / external interrupt |
| ピン 22 | RB1 — PORTB bit 1 (digital I/O) |
| ピン 23 | RB2 — PORTB bit 2 (digital I/O) |
| ピン 24 | RB3 — PORTB bit 3 (digital I/O) |
| ピン 25 | RB4 — PORTB bit 4 (digital I/O / interrupt-on-change) |
| ピン 26 | RB5 — PORTB bit 5 (digital I/O / interrupt-on-change) |
| ピン 27 | RB6/PGC — PORTB bit 6 / ICSP clock (also interrupt-on-change) |
| ピン 28 | RB7/PGD — PORTB bit 7 / ICSP data (also interrupt-on-change) |
主な用途
PIC16C66T-10E/SO の用途: 6 件s: Automotive Body and Chassis Control, Industrial Motor Speed Control, HVAC Fan and Damper Control, Smart Sensor Signal Conditioning, Battery-Powered Instrumentation, White Goods and Home Appliance Control.
Automotive Body and Chassis Control
The PIC16C66T-10E/SO is well suited to automotive body and chassis control modules (such as mirror controllers, wiper timing, and interior lighting drivers) because of its -40C to +125C automotive temperature grade, on-chip BOR/POR for safe crank-cold-start behaviour, and 22 I/O lines that can directly drive relay coils and low-side MOSFET switches. The 5 V supply matches the vehicle's regulated accessory rail, and the USART supports LIN-bus slave communication with a small external transceiver. Compared with newer flash PIC16F parts, the OTP memory is acceptable here because the firmware is mature and locked at production. The 10 MHz / 200 ns instruction cycle is fast enough to scan 8-16 input buttons at sub-10 ms latency and run a 100 Hz PID loop on a seat-position actuator without leaving headroom for code.
おすすめ
Industrial Motor Speed Control
In low-power industrial motor speed controllers (small DC brush or unipolar stepper drives under 50 W), the PIC16C66T-10E/SO delivers the 10-bit PWM channel plus two 8-bit timers needed to generate complementary drive waveforms, sense back-EMF through the analog comparator, and implement closed-loop speed regulation. The 22 I/O lines are sufficient to drive a 4-phase stepper with a discrete H-bridge and accept quadrature encoder feedback. The 5 V supply and automotive temperature grade give this part an unusually wide environmental envelope for a 14 KB OTP MCU, which simplifies the bill of materials when the same board layout is reused across industrial and automotive product variants.
おすすめ
HVAC Fan and Damper Control
The PIC16C66T-10E/SO fits HVAC fan and damper actuators where the controller runs a closed-loop temperature set-point and modulates a 24 VAC damper motor through a triac. The hardware USART supports Modbus RTU over RS-485 with an external transceiver, which is the dominant industrial HVAC fieldbus. Brown-out detect and power-on reset prevent false triac firing during brown-out conditions, an important safety consideration. The automotive temperature grade is more than enough for plenum-mounted controls that may see +85C air, and the 14 KB OTP holds the look-up tables, PID loop, and Modbus handler without needing external EEPROM.
おすすめ
Smart Sensor Signal Conditioning
The PIC16C66T-10E/SO functions as a smart-sensor front-end that digitizes a 0-5 V analog signal (via external ADC or internal analog comparator), applies linearization in firmware, and outputs the calibrated value over USART or I2C. With 14 KB of OTP, designers can pack linearization, calibration, and a Modbus or custom protocol handler without an external EEPROM. The wide operating temperature range lets the same hardware serve industrial, agricultural, and automotive sensor modules. USART or I2C at the pins allows direct connection to a host PLC, display, or gateway MCU.
おすすめ
Battery-Powered Instrumentation
In battery-powered instrumentation such as portable gas detectors, hand-held multimeters, or wireless remote keyless entry (RKE) transmitters, the PIC16C66T-10E/SO Sleep mode draws < 1 uA, and the WDT wakes the part periodically to read sensors and transmit over USART. The 5 V rail is straightforward to generate from a 9 V battery through an MCP1700 LDO, and the 22 I/O lines can directly drive a piezo buzzer, an LCD, and a 4-button keypad. The 14 KB OTP holds the keypad debouncer, sensor linearization, and a low-duty-cycle RF encoder for sub-GHz transmit.
おすすめ
White Goods and Home Appliance Control
The PIC16C66T-10E/SO is a common choice for white-goods control boards (washing machines, dishwashers, microwave ovens, induction cooktops) where the MCU must run a user interface, drive a relay matrix, and time motor sequences. The 22 I/O lines can scan a 4x4 matrix keypad, drive a 7-segment display through external transistors, and switch 8-12 relay coils. The PWM module controls a buzzer for user feedback. With the 14 KB OTP, designers can hold the entire appliance state machine plus factory-test routines in a single chip, and the automotive temperature grade ensures reliability in the high-heat environment behind a dishwasher or oven fascia.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C66T-10E/SO — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C66T-10/SO | PIC16C66-10I/SO | PIC16C66-20I/SO | PIC16C66-04I/SO |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SOIC (wide-body) | 28-SOIC (wide-body) | 28-SOIC (wide-body) | 28-SOIC (wide-body) | 28-SOIC (wide-body) |
| Core / Architecture | 8-bit PIC16 RISC | 8-bit PIC16 RISC | 8-bit PIC16 RISC | 8-bit PIC16 RISC | 8-bit PIC16 RISC |
| Program Memory | 14 KB OTP | 14 KB OTP | 14 KB OTP | 14 KB OTP | 14 KB OTP |
| Data RAM | 368 bytes | 368 bytes | 368 bytes | 368 bytes | 368 bytes |
| Maximum Clock Frequency | 10 MHz | 10 MHz | 10 MHz | 20 MHz | 4 MHz |
| I/O Pins | 22 | 22 | 22 | 22 | 22 |
| Operating Temperature | -40C to +125C (Automotive / E) | 0C to +70C (Commercial) | -40C to +85C (Industrial / I) | -40C to +85C (Industrial / I) | -40C to +85C (Industrial / I) |
| Serial Interfaces | I2C/SPI, USART | I2C/SPI, USART | I2C/SPI, USART | I2C/SPI, USART | I2C/SPI, USART |
| PWM Module | Yes (10-bit, 1 channel) | Yes (10-bit, 1 channel) | Yes (10-bit, 1 channel) | Yes (10-bit, 1 channel) | Yes (10-bit, 1 channel) |
主な差別化要因
- Automotive temperature grade in the 28-SOIC wide-body package （vs PIC16C66T-10/SO)
- 10 MHz instruction throughput at 5 V （vs PIC16C66-04I/SO)
- OTP memory for locked production firmware （vs PIC16F76 (flash alternative))
設計ノート
Estimated: at VDD = 5.0 V, clock = 10 MHz, the PIC16C66T-10E/SO typically draws < 5 mA active and < 1 uA in Sleep. Place a 0.1 uF ceramic decoupling capacitor within 5 mm of pin 20 (VDD) and a 10 uF bulk cap near the supply input. The on-chip Brown-out Reset (BOR) is factory-trimmed and does not require external supervision; ensure VDD rise time is < 50 ms to avoid the BOR-hold window.
OTP memory is one-time programmable. Once a PIC16C66 is programmed, it cannot be erased. Prototype with a windowed PIC16C66 JW part or a flash-based PIC16F76 (pin-compatible) before committing the OTP code. Also, RA4 is open-drain and requires a pull-up to source high - this is the most common schematic bug when migrating from PIC16F to PIC16C.
Route OSC1/OSC2 traces short and parallel with a ground guard on one side to minimize EMI coupling into the system clock. Keep the crystal within 10 mm of the MCU and use the datasheet's load capacitor values (typically 15-33 pF) - high C values slow oscillator startup and may fail at the low end of the operating temperature range.
Pins RC6/RC7 (USART) and RB6/RB7 (ICSP) are also the ICSP programming pins. If a pull-up or pull-down is required on these pins for normal operation, keep the resistance above 10 kohm to avoid contention with the programmer's high-speed ICSP driver. A series 100 ohm on MCLR is recommended to limit programming voltage ringing.
コンプライアンス情報
RoHS and REACH compliance status inferred from Microchip product page (active lifecycle) and industry-standard for this part number. Halogen-free status not explicitly stated in the provided web data and is marked unknown. AEC-Q100 is not specifically stated for this part - the 'E' suffix indicates an extended operating temperature grade but does not on its own confirm AEC-Q100 automotive qualification.
