PIC16LF18325-I/ST - 8-bit 32MHz XLP MCU 14KB Flash | Microchip
部品番号: PIC16LF18325-I/ST ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.55 | $1.55 |
| 10 | $1.4 | $14.00 |
| 100 | $1.18 | $118.00 |
| 500 | $0.98 | $490.00 |
| 1,000 | $0.82 | $820.00 |
| 3,000 | $0.72 | $2,160.00 |
PIC16LF18325-I/ST 概要
An 8-bit PIC microcontroller (MCU) is a Harvard-architecture CMOS processor that integrates Flash program memory, SRAM, EEPROM, digital timers, and analog peripherals onto a single die. PIC microcontrollers sit in the broader hierarchy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor IC. The PIC16F1xxx family uses the enhanced mid-range core that adds a wider instruction set (49 instructions), a 16-level hardware stack, and CIP blocks versus the legacy baseline and mid-range cores, while remaining code-compatible with traditional PIC16 code, easing migration from PIC16F182x and PIC16F1847 designs.
Key features of the PIC16LF18325 include eXtreme Low Power (XLP) technology with sub-microampere sleep currents (typical 60 nA in sleep with RTC), four 16-bit timers, two each of I2C, SPI, and UART peripherals, a 10-bit ADC with computation, a 5-bit DAC, and four Configurable Logic Cells. The 32MHz internal oscillator eliminates an external crystal in many designs. PPS allows software remapping of digital peripheral functions to most I/O pins, easing PCB layout in tight designs and allowing the same firmware to support multiple board revisions.
This PIC16LF18325-I/ST variant uses 14-pin TSSOP (ST) packaging (industrial -40C to +85C). Other ordering codes in the family cover PDIP-14, SOIC-14 (SL), and 16-pin UQFN and VQFN. The LF prefix denotes the low-voltage, low-power process technology optimized for battery-powered designs. The PIC16F18325 (F) variant uses a wider 2.3V-5.5V supply range and is otherwise electrically equivalent for code development.
Typical applications include IoT sensor nodes, battery-powered remotes, low-power wearables, home automation endpoints, small consumer appliances, and sensor hub modules. The integrated CIPs (CLC, CWG, NCO) allow replacing external logic gates, comparators, and oscillator ICs with on-chip hardware, reducing BOM and PCB area, while XLP sleep currents below 1 uA extend coin-cell battery life to years.
When designing with this device, allocate a 0.1 uF X7R 10V decoupling capacitor within a few millimeters of the VDD pin, route ICSP signals (ICSPCLK/ICSPDAT) to a dedicated 5-pin programming header, and verify the MCLR line has a 10 kohm pull-up to VDD; if unused, MCLR must be tied high (cannot be left floating) for normal operation. Brown-out Reset (BOR) and the Windowed Watchdog Timer (WWDT) should both be enabled in configuration words for safety-critical firmware.
This page synthesizes distributor pricing, same-family TSSOP drop-in alternatives, and practical design notes not aggregated in any single vendor datasheet or distributor listing.
ドロップイン代替品: PIC16LF18325-I/ST — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16LF18325-I/ST （同一形状・フットプリント） — 相違点: ADC, DAC, Operating Temperature, Communication, Core Architecture.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16F18325-I/ST
✅ ドロップイン✓ 在庫あり
$1.16 / 個
データシートを見る →PIC16LF18326-I/ST
✅ ドロップイン✓ 在庫あり
$1.18 / 個
データシートを見る →PIC16LF18324-I/ST
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16LF18325-I/ST 最大定格＆電気的特性
| Core Architecture | Enhanced Mid-Range 8-bit PIC (Harvard) |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data SRAM | 1 KB |
| Data EEPROM | 256 B |
| Maximum CPU Speed | 32 MHz (8 MIPS) |
| Supply Voltage (VDD) | 1.8 V to 3.6 V |
| 動作温度 | -40 C to +85 C (Industrial) |
| I/O Pins | 12 (on 14-pin TSSOP) |
| ADC | 10-bit, up to 11 channels, with computation |
| DAC | 5-bit, 1 channel |
| Timers | 4 x 16-bit Timer, 1 x 8-bit Timer |
| Communication | 2 x I2C, 2 x SPI, 2 x UART |
| Core Independent Peripherals (CIPs) | CLC, CWG, NCO, DSM, PWM, HCC |
| Peripheral Pin Select (PPS) | Yes (digital peripheral remapping) |
| XLP Sleep Current | Typical 60 nA (sleep with WDT/RTC) |
| Windowed Watchdog Timer (WWDT) | Yes |
| パッケージ | 14-pin TSSOP (ST) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
PIC16LF18325-I/ST ピン構成
| ピン 1 | VDD — Positive supply voltage (1.8V to 3.6V) |
| ピン 2 | RA5 — Digital I/O / analog input / ICSPDAT |
| ピン 3 | RA4 — Digital I/O / analog input / ICSPCLK |
| ピン 4 | RA3/MCLR — Master Clear reset (active-low) or digital I/O; tie to VDD via 10k if unused |
| ピン 5 | RC5 — Digital I/O / CCP1 / PWM output |
| ピン 6 | RC4 — Digital I/O / I2C SCL / SPI SS |
| ピン 7 | RC3 — Digital I/O / I2C SDA / SPI SDO |
| ピン 8 | RC2 — Digital I/O / analog input AN6 |
| ピン 9 | RC1 — Digital I/O / analog input AN5 / DAC output |
| ピン 10 | RC0 — Digital I/O / analog input AN4 |
| ピン 11 | RA2 — Digital I/O / analog input AN2 / DAC reference |
| ピン 12 | RA1 — Digital I/O / analog input AN1 / DAC output |
| ピン 13 | RA0 — Digital I/O / analog input AN0 |
| ピン 14 | VSS — Ground reference |
主な用途
PIC16LF18325-I/ST の用途: 6 件s: Battery-Powered IoT Sensor Node, Home Automation Endpoints, Wearable Health / Fitness Devices, Low-Power Wireless Remote Controls, Small Consumer Appliance Controllers, Industrial Sensor Hubs and Modbus Nodes.
Battery-Powered IoT Sensor Node
The PIC16LF18325-I/ST is purpose-built for battery-powered IoT sensor nodes where 1.8V-3.6V operation and sub-microampere sleep currents extend battery life to years. The XLP technology delivers 60 nA typical sleep current with WDT, while the integrated 10-bit ADC with computation can wake the CPU only when a meaningful sensor delta occurs, eliminating continuous polling. The 32 MHz enhanced mid-range core gives 8 MIPS for local edge processing of temperature, humidity, or motion data, while the 14 KB Flash holds application code, calibration tables, and a small LoRa or Sub-GHz protocol stack. The CLC and NCO Core Independent Peripherals can run in sleep mode to generate wake-up pulses, count events, or modulate IR signals without the CPU, dramatically lowering average power compared to software loops on legacy PIC16 mid-range parts.
おすすめ
Home Automation Endpoints
The PIC16LF18325-I/ST is well-suited for home automation endpoints such as battery-powered wireless switches, occupancy sensors, motorized blinds, and door/window contacts. Its 12 GPIO pins (in TSSOP-14) plus PPS (Peripheral Pin Select) let one firmware image support multiple board revisions without ICSP changes, and the same MCU can act as UART bridge, I2C sensor aggregator, or PWM LED controller by remapping peripherals at runtime. The two UART, two I2C, and two SPI interfaces support concurrent communication with a Sub-GHz radio, an environmental sensor, and an external EEPROM for log storage. The 32 MHz CPU plus 1 KB SRAM comfortably drives BLE / Zigbee / LoRa protocol stacks sized for endpoint nodes. Brown-out Reset and Windowed Watchdog Timer are essential safety features for always-on mains-powered gateway peripherals.
おすすめ
Wearable Health / Fitness Devices
The PIC16LF18325-I/ST targets wearable health and fitness devices such as heart-rate straps, smart watches, and continuous glucose monitor pendants. The LF process supports 1.8V operation directly from a single Li-ion cell with no boost converter, while XLP sleep currents below 1 uA preserve battery during standby days. The 32 MHz core can run on-demand DSP routines for heart-rate variability (HRV) analysis or pedometer algorithms in <10 ms, then return to sleep, keeping average current low. The 10-bit ADC with computation handles bioimpedance and optical PPG (photoplethysmogram) front-end sampling at low duty cycle. PPS allows swapping UART to SPI to free pins for a low-power display driver or haptic feedback motor, while the 1 KB SRAM holds a 1-second circular buffer of 100 Hz sensor data without external memory.
おすすめ
Low-Power Wireless Remote Controls
The PIC16LF18325-I/ST is ideal for low-power wireless remote controls, IR/RF transmitters, BLE beacons, and key fobs. Its 1.8-3.6V VDD range runs directly from 2xAA alkaline or a CR2032 coin cell, while CWG (Complementary Waveform Generator) and NCO (Numerically Controlled Oscillator) Core Independent Peripherals generate precise IR carrier frequencies (38 kHz, 40 kHz, 56 kHz) and Sub-GHz modulation without CPU intervention. The PPS module remaps UART or SPI to any GPIO, allowing a single PCB layout to support 433 MHz, 868 MHz, 915 MHz, and 2.4 GHz radio modules. The 4 KB of unused Flash space stores multiple button-mapping profiles, and EEPROM retains pairing codes through battery replacement. With 60 nA sleep, a CR2032 coin cell lasts 5+ years in a typical TV/BLE remote control duty cycle.
おすすめ
Small Consumer Appliance Controllers
The PIC16LF18325-I/ST is well-matched to small consumer appliance controllers, including electric toothbrushes, coffee machines, garment steamers, and personal care devices. Its 12 GPIO and 4 16-bit timers drive motor control (DC brushed, BLDC sensorless) and triac-fired heater loads, while the 10-bit ADC reads temperature from NTC thermistors or PTC heaters with hardware computation (averaging, oversampling). CLC cells implement custom logic glue, replacing discrete 74HC gates for safety interlocks - if temperature exceeds threshold, CLC directly disables PWM output. The 14 KB Flash holds USB HID, capacitive touch, and BLE firmware, and PPS reuses the same MCU across multiple SKUs by remapping button pins at runtime. Industrial -40C to +85C rating supports garage and outdoor appliance environments.
おすすめ
Industrial Sensor Hubs and Modbus Nodes
The PIC16LF18325-I/ST serves as a compact industrial sensor hub or Modbus RTU node in factory automation, building automation, and HVAC control panels. Its two UART ports enable simultaneous RS-485 Modbus master and a debug console, while the two I2C buses connect multiple temperature, pressure, and humidity sensors. The 10-bit ADC with computation handles 4-20 mA loop current sensing and 0-10V analog input scaling, and the 5-bit DAC generates reference voltages for bridge excitation. PPS allows routing UART, SPI, or PWM to alternate pins, simplifying the same PCB to support different connector pinouts. The industrial -40C to +85C temperature rating is qualified for factory floor and outdoor cabinet environments, and the 32 MHz core processes Modbus RTU packets with sub-millisecond latency at 115,200 baud.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16LF18325-I/ST — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16F18325-I/ST | PIC16LF18326-I/ST | PIC16LF18324-I/ST | PIC16LF18325-I/SL |
|---|---|---|---|---|---|
| Package | 14-pin TSSOP (ST) | 14-pin TSSOP (ST) - same | 14-pin TSSOP (ST) - same | 14-pin TSSOP (ST) - same | 14-pin SOIC (SL) - different |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 14 KB | 14 KB | 28 KB | 7 KB | 14 KB |
| Data SRAM | 1 KB | 1 KB | 2 KB | 512 B | 1 KB |
| Supply Voltage (VDD) | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Maximum CPU Speed | 32 MHz (8 MIPS) | 32 MHz (8 MIPS) | 32 MHz (8 MIPS) | 32 MHz (8 MIPS) | 32 MHz (8 MIPS) |
| XLP Sleep Current | 60 nA typical | 60 nA typical | 60 nA typical | 60 nA typical | 60 nA typical |
| Pin Count | 14 | 14 | 14 | 14 | 14 |
| 10-bit ADC Channels | 11 channels | 11 channels | 11 channels | 11 channels | 11 channels |
主な差別化要因
- Lowest-voltage operation in the PIC16F1xxx family （vs PIC16F18325-I/ST)
- 2x larger Flash for protocol stacks （vs PIC16LF18324-I/ST)
- Industry-standard 14-pin TSSOP footprint （vs PIC16LF18325-I/P (PDIP-14))
設計ノート
Estimated: at VDD=3.3V and active CPU at 32 MHz, the PIC16LF18325-I/ST typically draws 2-3 mA. In sleep mode with WDT enabled the XLP current drops to 60 nA typical, supporting multi-year battery life on a CR2032 coin cell. Use the IDLE mode (CPU off, peripherals running) to achieve ~1 mA when only ADC + CLC are active. Disable unused peripherals via PMDx registers to minimize active current.
Place a 0.1 uF X7R 10V decoupling capacitor within 5 mm of the VDD pin (pin 1) and a 10 uF bulk capacitor on the same VDD net for switching loads. Keep ICSPCLK/ICSPDAT (RA4/RA5) traces short and route them to a 5-pin ICSP header with no series resistors. If the design uses PPS, reserve the ICSP pins to avoid contention during in-circuit programming. Ground the thermal pad (if used in the UQFN variant); the TSSOP-14 has no exposed pad.
The MCLR pin (RA3/MCLR) MUST be tied to VDD through a 10 kohm pull-up resistor in normal operation; leaving it floating prevents the device from starting up reliably. Enable Brown-out Reset (BOR) in configuration words with a threshold appropriate for your supply (e.g., BORV = 1 for 2.5V minimum). If using the Windowed Watchdog Timer, configure the window carefully to avoid spurious resets during long interrupt service routines.
Route the external crystal traces (if used instead of the internal HFINTOSC) symmetrically and within 5 mm of the OSC1/OSC2 pins, with a ground guard ring. For ADC accuracy, separate the analog AVdd/AVss pins (in larger packages) and add a ferrite bead between digital and analog VDD. Keep PWM outputs (CWG) and high-speed switching signals away from analog input traces to minimize coupling. Use a star ground topology with a single-point connection between digital and analog ground planes.
コンプライアンス情報
RoHS compliant per Microchip product page. Industrial -40C to +85C temperature grade (I suffix). The E (extended -40C to +125C) variant is not available for this part number; for automotive AEC-Q100 grade consider PIC16F18325-E/ST or similar.
