PIC18F2480-E/SO - 8-bit MCU, 16KB Flash, ECAN, 28-SOIC | Microchip
部品番号: PIC18F2480-E/SO ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $15.25 | $15.25 |
| 10 | $13.78 | $137.80 |
| 100 | $12.21 | $1,221.00 |
| 500 | $10.85 | $5,425.00 |
| 1,000 | $9.42 | $9,420.00 |
PIC18F2480-E/SO 概要
An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, non-volatile program memory, RAM, and peripherals such as timers, communication interfaces, and analog-to-digital converters onto a single die. Within the broader taxonomy, 8-bit MCUs sit below 16-bit and 32-bit devices in computational throughput but above pure digital logic in integration density, making them the dominant choice for cost-sensitive embedded control. The PIC18 family specifically targets C-compilable, high-performance 8-bit designs with peripheral-rich silicon.
Key features include 16 KB self-programmable Flash (8K x 16 words), 768 bytes of RAM, 256 bytes of EEPROM, hardware ECAN 2.0B controller with acceptance filters, nanoWatt technology for ultra-low-power sleep modes (down to sub-microampere), and a 10-bit ADC with 8 input channels. The instruction set is highly orthogonal and C-friendly, and the device supports in-circuit serial programming (ICSP) plus in-circuit debug via ICD.
The PIC18F2480 architecture uses a 16-bit instruction word with an 8-bit data path, a hardware multiplier for 8x8 single-cycle operations, and four priority-level nested interrupts. It is built on a low-power CMOS process with brown-out reset, watchdog timer, and wide operating voltage (2.0V-5.5V for the F-version; the -E suffix denotes the extended -40C to +125C temperature range).
Typical applications include automotive ECAN nodes, industrial CAN-based sensor networks, building automation, HVAC controls, and CAN-to-UART bridges. The integrated ECAN peripheral eliminates the need for an external CAN controller, reducing BOM cost and PCB footprint in distributed control systems.
When designing with this part, place a 100 nF decoupling capacitor adjacent to each VDD/VSS pin pair and a 10 uF bulk capacitor near the regulator output. The ECAN bus requires a 120 ohm termination at each end of the bus and an isolated CAN transceiver such as the MCP2551 for proper differential signaling.
This page synthesizes distributor inventory, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, helping engineers evaluate the PIC18F2480-E/SO for new designs and legacy maintenance scenarios.
ドロップイン代替品: PIC18F2480-E/SO — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC18F2480-E/SO （同一形状・フットプリント） — 相違点: Package, Timers, Operating Temperature, ADC, Program Memory (Flash).
クイック比較ツール — 並列比較する代替部品を選択:
PIC18F2580-E/SO
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC18F248-I/SO
✅ ドロップイン✓ 在庫あり
$5.66 / 個
データシートを見る →PIC18F2480-I/SO
✅ ドロップイン✓ 在庫あり
$4.13 / 個
データシートを見る →PIC18F4480-I/SO
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC18F2455-I/SO
✅ ドロップイン✓ 在庫あり
$6.4 / 個
データシートを見る →PIC18F2431-I/SO
✅ ドロップイン✓ 在庫あり
$4.85 / 個
データシートを見る →PIC18F2480-E/SO 最大定格＆電気的特性
| Core Architecture | PIC18 (8-bit RISC) |
| Program Memory | 16 KB Flash (8K x 16) |
| Data SRAM | 768 bytes |
| Data EEPROM | 256 bytes |
| Maximum CPU Speed | 40 MHz (10 MIPS) |
| Supply Voltage (F-version) | 2.0 V to 5.5 V |
| Supply Voltage (Industrial) | 4.2 V to 5.5 V |
| I/O Pins | 25 |
| ADC | 10-bit, 8 channels |
| Timers | 4 (Timer0/1/2/3) |
| Communication | ECAN 2.0B, UART, SPI, I2C |
| パッケージ | 28-SOIC (SO, 300 mil) |
| 動作温度 | -40C to +125C (E suffix = extended) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Instruction Set | PIC18 16-bit instruction word, 8-bit data path |
| In-Circuit Programming | ICSP and ICD support |
PIC18F2480-E/SO ピン構成
| ピン 1 | MCLR/RE3 — Master Clear (reset) input / digital I/O RE3 |
| ピン 2 | RA0/AN0 — Digital I/O RA0 / analog input AN0 |
| ピン 3 | RA1/AN1 — Digital I/O RA1 / analog input AN1 |
| ピン 4 | RA2/AN2/VREF- — Digital I/O RA2 / analog AN2 / ADC VREF- |
| ピン 5 | RA3/AN3/VREF+ — Digital I/O RA3 / analog AN3 / ADC VREF+ |
| ピン 6 | RA4/T0CKI/C1OUT — Digital I/O RA4 / Timer0 clock / comparator output |
| ピン 7 | RA5/AN4/SS/C2OUT — Digital I/O RA5 / analog AN4 / SPI SS / comparator output |
| ピン 8 | VSS — Ground reference |
| ピン 9 | OSC1/CLKI/RA7 — Crystal oscillator input / external clock / digital I/O RA7 |
| ピン 10 | OSC2/CLKO/RA6 — Crystal oscillator output / clock out / digital I/O RA6 |
| ピン 11 | RC0/T1OSO/T1CKI — Digital I/O RC0 / Timer1 oscillator output / Timer1 clock |
| ピン 12 | RC1/T1OSI/CCP2 — Digital I/O RC1 / Timer1 oscillator input / CCP2 PWM |
| ピン 13 | RC2/CCP1 — Digital I/O RC2 / CCP1 PWM/capture/compare |
| ピン 14 | RC3/SCK/SCL — Digital I/O RC3 / SPI SCK / I2C SCL |
| ピン 15 | RC4/SDI/SDA — Digital I/O RC4 / SPI SDI / I2C SDA |
| ピン 16 | RC5/SDO — Digital I/O RC5 / SPI SDO |
| ピン 17 | RC6/TX/CK — Digital I/O RC6 / UART TX / clock |
| ピン 18 | RC7/RX/DT — Digital I/O RC7 / UART RX / data |
| ピン 19 | VSS — Ground reference |
| ピン 20 | VDD — Positive supply voltage |
| ピン 21 | RB0/INT0/AN10 — Digital I/O RB0 / external interrupt 0 / analog AN10 |
| ピン 22 | RB1/INT1/AN8 — Digital I/O RB1 / external interrupt 1 / analog AN8 |
| ピン 23 | RB2/INT2/AN9 — Digital I/O RB2 / external interrupt 2 / analog AN9 |
| ピン 24 | RB3/INT3/AN11/CCP2 — Digital I/O RB3 / external interrupt 3 / analog AN11 / CCP2 |
| ピン 25 | RB4/KBI0/AN12 — Digital I/O RB4 / keyboard interrupt / analog AN12 |
| ピン 26 | RB5/KBI1/AN13 — Digital I/O RB5 / keyboard interrupt / analog AN13 |
| ピン 27 | RB6/KBI2/PGC — Digital I/O RB6 / keyboard interrupt / ICSP clock |
| ピン 28 | RB7/KBI3/PGD — Digital I/O RB7 / keyboard interrupt / ICSP data |
主な用途
PIC18F2480-E/SO の用途: 6 件s: Automotive CAN Bus Nodes, Industrial Sensor Networks with CAN, Building Automation and HVAC Controls, CAN-to-UART Protocol Bridges, Portable Battery-Powered CAN Data Loggers, Educational Embedded Development Platforms.
Automotive CAN Bus Nodes
The PIC18F2480-E/SO's integrated ECAN 2.0B controller and 40 MHz operation make it a drop-in node controller for in-vehicle CAN networks running at 125 kbps-500 kbps. The 25 I/O pins handle digital sensors and actuators, while the 10-bit ADC reads analog signals such as thermistors and potentiometers. Pair the MCU with an MCP2551 CAN transceiver for proper bus-level signaling on OBD-II and CAN-High/Low twisted-pair buses.
おすすめ
Industrial Sensor Networks with CAN
For factory-floor sensor nodes communicating over CANopen or DeviceNet, the PIC18F2480-E/SO delivers deterministic real-time response with its 4 priority-level nested interrupts and 16 KB C-friendly Flash. The nanoWatt power-down modes drop standby current below 1 uA between bus events, extending battery life in wireless-CAN hybrid nodes. The wide -40C to +125C industrial temperature range supports outdoor cabinet deployment.
おすすめ
Building Automation and HVAC Controls
The PIC18F2480-E/SO's ECAN interface enables distributed HVAC damper and actuator control over a single bus, eliminating parallel point-to-point wiring. The 10-bit ADC reads thermistor temperature sensors and 0-10 V analog setpoints, while PWM outputs drive variable-speed fans and motorized valves. The 256-byte EEPROM stores non-volatile setpoints and runtime hours across power cycles.
おすすめ
CAN-to-UART Protocol Bridges
For gateway applications converting CAN frames to legacy RS-232/RS-485 serial streams, the PIC18F2480-E/SO's ECAN and UART peripherals operate independently via DMA-style firmware flow control. The 40 MHz CPU sustains 1 Mbps CAN throughput while buffering and re-encoding frames, making it ideal for retrofitting older serial-controlled equipment onto CAN networks without firmware rewrite.
おすすめ
Portable Battery-Powered CAN Data Loggers
Battery-powered automotive diagnostics and fleet telematics benefit from the PIC18F2480-E/SO's nanoWatt sleep modes that draw less than 1 uA when the CAN bus is idle. The 16 KB Flash buffers several hours of OBD-II PIDs in a circular log, while the 10-bit ADC monitors battery voltage for low-power alerts. The extended -40C to +125C temperature range survives under-dash automotive environments.
おすすめ
Educational Embedded Development Platforms
The PIC18F2480-E/SO is widely used in university and training curricula due to its 28-SOIC easy-solder footprint, MPLAB X IDE support, and rich PIC18 peripheral set. Students learn CAN networking, 10-bit ADC acquisition, PWM motor control, and ICSP debugging on a single 8-bit platform. The XC8 compiler free tier supports the full PIC18 instruction set, lowering course-material cost.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC18F2480-E/SO — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC18F2580-E/SO | PIC18F248-I/SO | PIC18F2480-I/SO | PIC18F4480-I/SO |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SOIC (300 mil) | 28-SOIC (300 mil) - same | 28-SOIC (300 mil) - same | 28-SOIC (300 mil) - same | 28-SOIC (300 mil) - same |
| Program Memory | 16 KB Flash | 32 KB Flash | 8 KB Flash | 16 KB Flash | 16 KB Flash |
| Data RAM | 768 bytes | 1536 bytes | 768 bytes | 768 bytes | 768 bytes |
| ECAN Controller | ECAN 2.0B | ECAN 2.0B | Legacy CAN | ECAN 2.0B | ECAN 2.0B |
| Maximum Frequency | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS |
| Temperature Range | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) |
| Supply Voltage | 2.0V to 5.5V (F-version 4.2V-5.5V industrial) | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 5 channels | 10-bit, 8 channels | 10-bit, 11 channels |
| I/O Pins | 25 | 25 | 22 | 25 | 36 |
主な差別化要因
- Integrated Enhanced CAN 2.0B controller eliminates external CAN IC （vs PIC18F2455-I/SO)
- Extended -40C to +125C operating temperature （vs PIC18F2480-I/SO)
- 16 KB Flash vs legacy 8 KB on PIC18F248 （vs PIC18F248-I/SO)
- 8-channel 10-bit ADC for sensor-dense designs （vs PIC18F248-I/SO)
設計ノート
Decouple VDD (pin 20) with a 100 nF ceramic capacitor placed within 5 mm of the pin, plus a 10 uF bulk tantalum or ceramic capacitor near the IC for transient load support. PIC18F2480 ECAN transmit bursts draw sharp current spikes; insufficient decoupling can corrupt CAN frame CRC. The -E (extended) parts need 4.2V minimum at full 40 MHz speed; at lower VDD the oscillator may stall.
Route the ECAN TX/RX traces to the MCP2551 transceiver as a short impedance-controlled differential pair (characteristic impedance ~60 ohm), keep them away from switching regulator nodes, and place the transceiver close to the bus connector. The 120 ohm termination resistor should sit at the bus ends, not at every node. Avoid running CAN traces parallel to noisy clock or PWM lines for more than 25 mm to prevent capacitive crosstalk.
Configuration bits must be set correctly before code execution: enable the ECAN module's high-performance I/O, disable the Low-Voltage Programming (LVP) pin if not needed, and configure the oscillator mode (HS for >4 MHz crystal). Failing to set CONFIG4H LVP bit correctly can lock the device after programming. Brown-out Reset (BOR) must be enabled to avoid flash corruption during power-down - disable only with deliberate design rationale.
The ECAN controller's CANTX and CANRX lines are 5V CMOS logic; if connecting to a 3.3V transceiver, use a level shifter such as MCP2551's VIO supply pin or a discrete FET divider. CAN bus common-mode voltage range is -2V to +7V per ISO 11898; verify your cable shield and chassis ground bond to avoid ground loops that exceed this range in electrically noisy environments.
Estimated: at 40 MHz, 5V supply, and 25 mA active current (typical per datasheet DS39637A), power dissipation is ~125 mW. The 28-SOIC thermal resistance theta_JA is approximately 80 C/W on a 4-layer PCB with 1 oz copper. Junction temperature rise above ambient is therefore ~10C - well within the 125C maximum for -E (extended) grade parts even at +85C ambient industrial environments.
コンプライアンス情報
RoHS compliant per Microchip product page. AEC-Q100 qualification status not stated in the verified web data; -E grade indicates extended temperature but is not equivalent to AEC-Q100 automotive qualification.
