PIC18F4458-I/P - 8-bit 48MHz USB MCU 24KB Flash | Microchip
部品番号: PIC18F4458-I/P ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $7.87 | $7.87 |
| 10 | $7.09 | $70.90 |
| 100 | $5.94 | $594.00 |
| 500 | $5.21 | $2,605.00 |
| 1,000 | $4.62 | $4,620.00 |
PIC18F4458-I/P 概要
Background: An 8-bit microcontroller (MCU) is a single-chip computer optimized for byte-oriented control tasks in embedded systems. Within the MCU taxonomy, PIC18F devices sit above base-line PIC16 parts, providing enhanced 16-bit wide instruction paths, hardware multiplier, C-friendly architecture, and richer peripherals while retaining the classic PIC RISC design. The PIC18F4458 belongs to the PIC18F4550 family of Full-Speed USB microcontrollers, distinguished from PIC18F-K-series parts by its USB SIE and nanoWatt features aimed at connected, battery-aware products.
Key differentiating features include a USB 2.0 Full-Speed (12 Mbit/s) Serial Interface Engine, three independent serial ports (USB, I2C, SPI up to 10 Mbit/s), an EUSART for asynchronous/synchronous RS-232/RS-485 communications, a 10-channel 12-bit ADC, two analog comparators, and a hardware master/slave PSP. The device supports operating voltages of 2.0V to 5.5V and provides self-programmability for bootloader firmware updates.
The architecture combines a Harvard RISC core with a 16-bit instruction word and 8-bit data path, an 8 x 8 hardware multiplier for math acceleration, and a 31-level hardware stack that supports high-level language compilers (MPLAB C18). nanoWatt features include multiple idle/sleep modes, ultra-low-power wake-up on change, and a real-time clock with dedicated low-power oscillator.
Typical applications include Full-Speed USB peripherals (HID, CDC, vendor-class), industrial sensor hubs, low-power data loggers, and embedded control nodes requiring USB connectivity. Design considerations include provision for a 20 MHz external crystal when USB accuracy is required, decoupling on AVDD/VUSB rails, and MCLR pull-up for reliable reset behavior.
ドロップイン代替品: PIC18F4458-I/P — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC18F4458-I/P （同一形状・フットプリント） — 相違点: Package, Timers, Core, Operating Temperature, Serial Interfaces.
クイック比較ツール — 並列比較する代替部品を選択:
PIC18F4550-I/P
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC18F4455-I/PT
✅ ドロップイン✓ 在庫あり
$4.85 / 個
データシートを見る →PIC18F4450-I/P
✅ ドロップイン✓ 在庫あり
$6.05 / 個
データシートを見る →PIC18F4420-I/P
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC18F4320-I/P
✅ ドロップイン✓ 在庫あり
$4.05 / 個
データシートを見る →PIC18F4458-I/P 最大定格＆電気的特性
| Core | PIC18F 8-bit Harvard RISC |
| Instruction Set Width | 16-bit |
| Data Path | 8-bit |
| Max CPU Frequency | 48 MHz |
| Program Memory (Flash) | 24 KB (12K x 16 words) |
| SRAM | 2 KB |
| EEPROM | 256 bytes |
| I/O Pins | 34 (40-pin PDIP) |
| Operating Voltage Range | 2.0 V to 5.5 V |
| ADC | 10-channel, 12-bit |
| USB | USB 2.0 Full-Speed (12 Mbit/s) SIE |
| Serial Interfaces | USB, EUSART, I2C, SPI (up to 10 Mbit/s) |
| Comparators | 2 analog comparators |
| Timers | 1 x 8-bit, 3 x 16-bit |
| パッケージ | 40-pin PDIP (0.600", 15.24 mm) |
| 実装タイプ | Through-Hole |
| 動作温度 | -40C to +85C (Industrial, -I suffix) |
| Programming | ICSP via PGC/PGD, self-programmable |
| RoHS ステータス | Compliant |
PIC18F4458-I/P ピン構成
| ピン 1 | RB0/INT0/FLT0/AN12 — PORTB bit 0, external interrupt 0, ECCP fault input, analog input 12 |
| ピン 2 | RB1/INT1/AN10 — PORTB bit 1, external interrupt 1, analog input 10 |
| ピン 3 | RB2/INT2/AN8 — PORTB bit 2, external interrupt 2, analog input 8 |
| ピン 4 | RB3/AN9/CCP2 — PORTB bit 3, analog input 9, ECCP2 capture/compare/PWM |
| ピン 5 | RB4/AN11/KBI0 — PORTB bit 4, analog input 11, interrupt-on-change |
| ピン 6 | RB5/KBI1/PGM — PORTB bit 5, interrupt-on-change, low-voltage ICSP |
| ピン 7 | RB6/KBI2/PGC — PORTB bit 6, interrupt-on-change, ICSP clock |
| ピン 8 | RB7/KBI3/PGD — PORTB bit 7, interrupt-on-change, ICSP data |
| ピン 9 | VSS — Logic ground |
| ピン 10 | VDD — Logic power supply (2.0V to 5.5V) |
| ピン 11 | VSS — Logic ground (return pair for VDD) |
| ピン 12 | RA0/AN0 — PORTA bit 0, analog input 0 |
| ピン 13 | RA1/AN1 — PORTA bit 1, analog input 1 |
| ピン 14 | RA2/AN2/VREF- — PORTA bit 2, analog input 2, ADC VREF- |
| ピン 15 | RA3/AN3/VREF+ — PORTA bit 3, analog input 3, ADC VREF+ |
| ピン 16 | RA4/T0CKI/C1OUT — PORTA bit 4, Timer0 clock input, comparator 1 output |
| ピン 17 | RA5/AN4/SS1/HLVDIN/C2OUT — PORTA bit 5, analog input 4, SPI1 slave select, HLVD input, comparator 2 output |
| ピン 18 | RC0/T1OSO/T1CKI — PORTC bit 0, Timer1 oscillator output, Timer1 clock input |
| ピン 19 | RC1/T1OSI/CCP2/UOE — PORTC bit 1, Timer1 oscillator input, ECCP2, USB OE |
| ピン 20 | RC2/CCP1/P1A — PORTC bit 2, ECCP1, PWM output A |
| ピン 21 | RC4/D-/VM — PORTC bit 4, USB D-, USB VM monitor |
| ピン 22 | RC5/D+/VP — PORTC bit 5, USB D+, USB VP monitor |
| ピン 23 | RC6/TX1/CK1 — PORTC bit 6, EUSART1 TX, EUSART1 clock |
| ピン 24 | RC7/RX1/DT1 — PORTC bit 7, EUSART1 RX, EUSART1 data |
| ピン 25 | RD0/SPP0 — PORTD bit 0, Streaming Parallel Port data 0 |
| ピン 26 | RD1/SPP1 — PORTD bit 1, Streaming Parallel Port data 1 |
| ピン 27 | RD2/SPP2 — PORTD bit 2, Streaming Parallel Port data 2 |
| ピン 28 | RD3/SPP3 — PORTD bit 3, Streaming Parallel Port data 3 |
| ピン 29 | RD4/SPP4 — PORTD bit 4, Streaming Parallel Port data 4 |
| ピン 30 | RD5/SPP5/P1B — PORTD bit 5, Streaming Parallel Port data 5, PWM output B |
| ピン 31 | RD6/SPP6/P1C — PORTD bit 6, Streaming Parallel Port data 6, PWM output C |
| ピン 32 | RD7/SPP7/P1D — PORTD bit 7, Streaming Parallel Port data 7, PWM output D |
| ピン 33 | VUSB — USB internal 3.3V regulator output (bypass cap required) |
| ピン 34 | AVDD — Analog power supply |
| ピン 35 | AVSS — Analog ground |
| ピン 36 | RE0/RD/AN5 — PORTE bit 0, Parallel Slave Port read, analog input 5 |
| ピン 37 | RE1/WR/AN6 — PORTE bit 1, Parallel Slave Port write, analog input 6 |
| ピン 38 | RE2/CS/AN7 — PORTE bit 2, Parallel Slave Port chip select, analog input 7 |
| ピン 39 | OSC1/CLKI/RA7 — External crystal input, external clock input, PORTA bit 7 |
| ピン 40 | OSC2/CLKO/RA6 — External crystal output, clock output, PORTA bit 6 |
主な用途
PIC18F4458-I/P の用途: 6 件s: Full-Speed USB HID Peripherals, USB CDC Virtual COM Port Bridge, Industrial Sensor Hub with USB Logging, Embedded Bootloader / Field-Upgradable Appliance, Low-Power Data Logger with USB Dump, USB Educational Development Board.
Full-Speed USB HID Peripherals
The PIC18F4458-I/P is ideal for Full-Speed USB HID peripherals such as keyboards, mice, game controllers, and custom input devices because its integrated USB 2.0 SIE handles 12 Mbit/s framing without an external PHY. With 24 KB Flash and 2 KB SRAM, the device comfortably fits the HID bootloader, HID descriptor table, and a small matrix-scan or vendor report handler. Its 48 MHz core provides the throughput to maintain 1000 Hz polling while servicing ADC and GPIO scan in parallel.
おすすめ
USB CDC Virtual COM Port Bridge
The PIC18F4458-I/P excels in USB CDC virtual COM port bridges used to replace legacy RS-232 ports on embedded systems, because the integrated USB SIE and EUSART can run concurrently. Its 48 MHz core and 2 KB SRAM sustain full-duplex USB-to-UART throughput without dropped bytes, while the 12-bit ADC enables the bridge to also report supply voltage or temperature over the same CDC interface. Engineers can re-use the same firmware skeleton for both USB and serial-only products, simply commenting out the USB stack for the latter.
おすすめ
Industrial Sensor Hub with USB Logging
For industrial sensor hubs that stream ADC readings to a host PC, the PIC18F4458-I/P combines a 10-channel 12-bit ADC with USB CDC for plug-and-play data logging. Its 48 MHz core runs background averaging while the USB endpoint delivers 1 kHz report streams, and its nanoWatt sleep modes drop the quiescent current below 1 uA when the host is offline. The 40-pin PDIP package simplifies through-hole assembly in ruggedized industrial enclosures and provides ample I/O for I2C, SPI, and analog sensor multiplexing.
おすすめ
Embedded Bootloader / Field-Upgradable Appliance
The PIC18F4458-I/P supports bootloader-based field upgrades via ICSP and self-programmable Flash, allowing products to receive firmware updates over USB from a host PC without opening the enclosure. Its 24 KB Flash reserves 8 KB for the bootloader while leaving 16 KB for application code, and the 2 KB SRAM supports modular firmware loading. The 40-pin PDIP package is convenient for both prototype development with through-hole headers and small-batch production.
おすすめ
Low-Power Data Logger with USB Dump
The PIC18F4458-I/P suits battery-powered data loggers that wake periodically, sample sensors, store to EEPROM, and dump logs to a USB host on demand. Its nanoWatt sleep modes cut quiescent current to under 1 uA, the 256-byte EEPROM holds configuration and calibration, and the USB SIE enables instant log retrieval without removing the SD card. Engineers can extend the design with an external I2C FRAM for high-density logging while the PIC handles USB and timing.
おすすめ
USB Educational Development Board
The PIC18F4458-I/P is a strong choice for USB-focused educational development boards because the 40-pin PDIP form factor fits standard solderless breadboards and through-hole perfboard, removing the need for soldering reflow equipment. Its full USB stack plus 12-bit ADC and three serial ports give students a complete peripheral set to learn embedded protocols. Microchip's MPLAB X IDE and XC8 compiler are free, lowering the educational adoption cost.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC18F4458-I/P — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC18F4550-I/P | PIC18F4455-I/P | PIC18F4450-I/P | PIC18F4420-I/P | PIC18F4320-I/P |
|---|---|---|---|---|---|---|
| Package | 40-pin PDIP | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Flash | 24 KB | 32 KB | 24 KB | 16 KB | 16 KB | 8 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 1.5 KB | 768 B | 512 B |
| USB SIE | USB 2.0 Full-Speed (12 Mbit/s) | USB 2.0 Full-Speed (12 Mbit/s) | USB 2.0 Full-Speed (12 Mbit/s) device-only | USB 2.0 Full-Speed (12 Mbit/s) | No USB | No USB |
| ADC Resolution | 12-bit, 10-channel | 12-bit, 13-channel | 12-bit, 10-channel | 10-bit, 8-channel | 10-bit, 8-channel | 10-bit, 8-channel |
| Operating Voltage | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V |
主な差別化要因
- Integrated USB 2.0 Full-Speed SIE without external PHY （vs PIC18F4320-I/P)
- Higher-resolution 12-bit ADC vs 10-bit siblings （vs PIC18F4450-I/P)
- 24 KB Flash balances bootloader and application code （vs PIC18F4550-I/P)
設計ノート
USB signaling on PIC18F4458 requires a 48 MHz clock with sufficient accuracy; using the internal HF-INTOSC with the active clock tuning against the USB SOF packets is acceptable but a 20 MHz external crystal with HSPLL is recommended for jitter-sensitive hosts. Decoupling the VUSB pin with a 220 nF capacitor and placing VUSB near a regulated 5V source is mandatory - omitting it causes USB enumeration failures.
For USB operation the part requires VDD >= 4.0V (per USB 2.0 spec); at lower voltages USB must be disabled in firmware. For non-USB applications the part operates from 2.0V to 5.5V. nanoWatt sleep currents drop below 1 uA when the system clock is gated and peripherals disabled, but peripherals connected to I/O pins must be tri-stated to prevent leakage through protection diodes.
Place a 100 nF decoupling capacitor on each VDD/AVDD pair within 3 mm of the pins, and add a bulk 10 uF tantalum or ceramic near the IC. The 40-pin PDIP package has long leads that introduce inductive loops at high current transients; star-ground VSS, AVSS, and USB ground returns to a single point. MCLR should pull up through a 10 kohm resistor to VDD for reliable reset unless programming through ICSP is the primary mode.
コンプライアンス情報
RoHS and lead-free compliant per Microchip product page; not AEC-Q100 qualified (consumer/industrial grade).
