PIC18LF442-I/P - 8-Bit 40MHz 16KB Flash MCU 40-PDIP | Microchip
部品番号: PIC18LF442-I/P ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.18 | $9.18 |
| 10 | $8.26 | $82.60 |
| 100 | $7.1 | $710.00 |
| 500 | $6.32 | $3,160.00 |
| 1,000 | $5.55 | $5,550.00 |
PIC18LF442-I/P 概要
A PIC18 microcontroller is part of Microchip's enhanced 8-bit MCU family that uses a modified Harvard architecture with separate program and data buses plus a 16-bit instruction word. PIC18 microcontrollers are positioned in Microchip's portfolio between the legacy PIC16 baseline family and the PIC24/dsPIC 16-bit families, and are widely adopted in motor control, sensing, low-power IoT edge nodes, and human-machine interface applications due to their deterministic interrupt latency, mature MPLAB XC8 toolchain support, and broad ecosystem of libraries.
Key features of the PIC18LF442-I/P include 40 MHz maximum clock speed (10 MIPS), 16 KB on-chip Flash program memory, 768 bytes SRAM, 256 bytes EEPROM, 34 I/O pins, three 16-bit timers, a 10-bit multi-channel ADC, USART, MSSP (SPI/I2C), and a 4x PLL. The 'LF' designator denotes the wide-voltage (2.0V-5.5V) variant suited to battery-powered systems; the 'I/P' suffix specifies the industrial temperature range (-40C to +85C) and PDIP-40 package. Internal RC oscillator, brown-out reset, and low-voltage detect simplify BOM cost.
The device uses a RISC instruction set with 77 single-word instructions, a hardware multiplier, and a 16-bit wide instruction bus for fast execution. Its 8-bit data path and accumulator-based register model support direct C compilation via MPLAB XC8 while preserving PIC legacy assembly code portability. The integrated 10-bit ADC delivers up to 8 channels, supporting up to ~20 kSPS for sensor signal acquisition in industrial control loops.
Typical applications include industrial automation controllers, HVAC sensor interface boards, low-cost consumer appliances, motor driver peripherals (small BLDC/PMSM), automotive body electronics (non-safety), and educational development boards. Designers choose this MCU when they need 8-bit simplicity, mature tooling, and a wide operating voltage range.
When designing with the PIC18LF442-I/P, ensure the configured clock source (HS, XT, internal RC) matches Fosc vs. VDD per the datasheet electrical specifications. Always enable the watchdog timer for industrial deployments, and reserve at least one timer for FreeRTOS/PIC18 SysTick-equivalent scheduling if real-time control is required.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not consolidated in the manufacturer datasheet alone, helping engineers shorten PIC18 BOM selection and qualification time.
ドロップイン代替品: PIC18LF442-I/P — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC18LF442-I/P （同一形状・フットプリント） — 相違点: ADC, Core Architecture, Package, Operating Temperature, Capture/Compare/PWM.
クイック比較ツール — 並列比較する代替部品を選択:
PIC18F442-I/P
✅ ドロップイン✓ 在庫あり
$5.4 / 個
データシートを見る →PIC18LF442-I/P 最大定格＆電気的特性
| Core Architecture | PIC18 (8-bit, modified Harvard) |
| Program Memory (Flash) | 16 KB (8K x 16) |
| RAM | 768 bytes |
| EEPROM | 256 bytes |
| Maximum CPU Speed | 40 MHz (10 MIPS) |
| Supply Voltage Range | 4.2 V to 5.5 V (PIC18LF variant, wide-Vdd) |
| I/O Pins | 34 |
| ADC | 10-bit, multi-channel (8 channels typical) |
| Timers | 3 x 16-bit Timer/Counter modules |
| Capture/Compare/PWM | Yes (CCP module) |
| Serial Peripherals | 1x USART (SCI), 1x MSSP (SPI/I2C) |
| パッケージ | 40-pin PDIP (DIP-40, plastic through-hole) |
| 動作温度 | -40 C to +85 C (Industrial) |
| 実装タイプ | Through-Hole (DIP) |
| Instruction Set | 77 single-word instructions |
| Oscillator Options | HS, XT, LP, RC, INTIO with PLL (x4) |
PIC18LF442-I/P 40-pin pdip (dip-40, plastic through-hole) ピン配置ガイド
PIC18LF442-I/P (40-pin pdip (dip-40, plastic through-hole) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: PIC18LF442-I/P.
詳細は データシート をご参照ください。
主な用途
PIC18LF442-I/P の用途: 6 件s: Industrial Sensor Interface Board, Small Motor Control / PWM Driver, HVAC Climate Control Board, Low-Cost Consumer Appliance Controller, Automotive Body Electronics (Non-Safety), Educational / Hobbyist Development Board.
Industrial Sensor Interface Board
The PIC18LF442-I/P is well-suited to industrial sensor interface boards thanks to its 34 digital I/O lines, 10-bit multi-channel ADC (8 channels), and 768 bytes of RAM for averaging or FIR filtering. The wide-voltage LF designator allows operation directly from a 24V->5V sensor rail without a secondary LDO. Engineers typically use the MSSP port in I2C mode to connect to external ADCs or temperature sensors, while the USART connects to an RS-485 transceiver for industrial fieldbus. The industrial -40C to +85C temperature range ensures operation in factory floor enclosures. The 256-byte EEPROM provides persistent storage for calibration coefficients. Power consumption at 4 MHz INTIO is below 2 mA active, allowing battery-backed sensor operation. The 16 KB Flash is adequate for a state-machine scheduler plus driver code.
おすすめ
Small Motor Control / PWM Driver
The PIC18LF442-I/P supports small motor control via its built-in CCP module (Capture/Compare/PWM), 34 I/O for H-bridge gate enable signals, and 16-bit timer for high-resolution PWM. The PIC18 core executes 10 MIPS at 40 MHz, which is sufficient for closed-loop PID running at 5-10 kHz control rate. The 10-bit ADC samples back-EMF or shunt current for torque and speed estimation. The 16 KB Flash accommodates a small RTOS plus field-oriented control (FOC) for sensorless BLDC, or simpler V/Hz control for AC induction motors. Industrial temperature grade supports motor cabinet deployment. Designers should reserve one 16-bit timer for PWM, one for ADC trigger, and one for FreeRTOS tick if used. The PDIP-40 package simplifies through-hole prototyping.
おすすめ
HVAC Climate Control Board
HVAC climate control boards use the PIC18LF442-I/P to read NTC thermistors, setpoint dials, and drive TRIAC-controlled fans, blowers, and valve actuators. The 10-bit ADC acquires up to 8 sensor channels, while the CCP PWM module controls TRIAC firing angles through optoisolators. The 256-byte EEPROM stores user preferences and learned PID gains across power cycles. USART or MSSP can drive an external LCD character display module via SPI for user interface. Industrial temperature range ensures operation near furnaces and refrigerant lines. The LF wide-voltage supply allows 5V operation from a 24VAC transformer + rectifier. Wide firmware headroom in 16 KB supports adaptive control algorithms. Low-power sleep modes below 1uA extend battery-backed thermostat life.
おすすめ
Low-Cost Consumer Appliance Controller
Consumer appliances (rice cookers, washing machines, coffee makers, microwave keypads) use the PIC18LF442-I/P for its low BOM cost, integrated 10-bit ADC for temperature/level sensing, and 16 KB Flash for user-interface firmware. The CCP/PWM controls element relays via TRIACs or zero-cross SSRs. The USART drives LED or 7-segment displays for user feedback. EEPROM stores cooking profiles and user presets. The PDIP-40 package simplifies hand-soldered prototypes and low-volume SKUs. The LF wide-voltage variant supports direct 3.3V or 5V operation. The PIC18 architecture and MPLAB XC8 toolchain offer fast time-to-market with extensive app-note libraries. Industrial -40C to +85C rating handles kitchen and laundry environments with thermal stress.
おすすめ
Automotive Body Electronics (Non-Safety)
The PIC18LF442-I/P suits non-safety automotive body electronics such as interior lighting controllers, mirror adjusters, seat-position memory modules, and accessory timers. The PIC18LF442 industrial temperature grade handles the -40C to +85C cabin environment. The 34 I/O drives multiplexed LED arrays and reads Hall sensors and switches via the 10-bit ADC. CAN is not integrated, so designers add an external MCP2515/MCP2551 CAN module for body bus networking. The 16 KB Flash handles state-machine seat memory logic. EEPROM stores user presets reliably. Note: for safety-critical automotive, choose AEC-Q100 qualified parts like PIC18F46K22-I/PT instead.
おすすめ
Educational / Hobbyist Development Board
Educational and hobbyist development boards use the PIC18LF442-I/P for its DIP-40 through-hole package, which fits standard 0.1 inch pitch breadboards and IC sockets for hand-soldering. The 16 KB Flash, 768-byte RAM, and 34 I/O support fundamental learning projects: LED blinking, ADC sensor reading, UART-to-PC terminal, PWM motor speed control, and I2C peripheral interfacing. The MPLAB X IDE + PICkit 3/4 + XC8 compiler free download lowers the entry cost. The 77-instruction RISC architecture is simple enough for assembly learning while C compilation is supported. The LF wide-voltage variant is forgiving of weak USB-to-serial power supplies in student kits. Many open-source references and app-notes exist for PIC18F442, easing the student's learning curve.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC18LF442-I/P — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC18F442-I/P |
|---|---|---|
| Package | 40-pin PDIP (DIP-40) | 40-pin PDIP - same |
| Brand | Microchip Technology | Microchip Technology |
| Core | PIC18 8-bit (10 MIPS) | PIC18 8-bit (10 MIPS) - same |
| Program Flash | 16 KB | 16 KB - same |
| RAM | 768 bytes | 768 bytes - same |
| EEPROM | 256 bytes | 256 bytes - same |
| Maximum Frequency | 40 MHz (10 MIPS) | 40 MHz - same |
| Operating Voltage | 2.0 V to 5.5 V (LF wide-Vdd) | 4.2 V to 5.5 V only |
| I/O Pins | 34 | 34 - same |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels - same |
主な差別化要因
- Wide-voltage LF variant supports 2.0V-5.5V operation （vs PIC18F442-I/P)
- Through-hole PDIP-40 simplifies prototyping and low-volume production （vs PIC18LF4423-I/PT)
- Mature PIC18 ecosystem with extensive app-notes and library support （vs PIC18F45K22-I/P)
設計ノート
Estimated: at 40 MHz Fosc and 5V Vdd, PIC18LF442-I/P active current is approximately 14 mA per Microchip datasheet DC characteristics. For battery-backed designs, enable Sleep mode (typical < 1 uA) and use INTIO at 4 MHz or 1 MHz to scale active current to 1-4 mA. Brown-Out Reset (BOR) must be enabled via CONFIG registers for industrial deployments to prevent code-execution corruption during brown-out events below 4.0 V.
Place decoupling capacitors (100 nF ceramic + 10 uF tantalum/electrolytic) within 5 mm of VDD pins 11 and 32. Connect VSS pins 12 and 31 to a ground plane using multiple vias for low-impedance return. Place the crystal (if used) within 10 mm of OSC1/OSC2 pins 13-14 with short traces and a guard ring tied to ground to minimize EMI and stray capacitance.
Do not skip the MCLR pull-up resistor on pin 1: a floating MCLR can cause spurious resets in noisy industrial environments. Use a 10 kohm pull-up to VDD with a 100 nF decoupling cap to VSS for hardware noise immunity. Always program the CONFIG bits for the WDT (Watchdog Timer) and BOR (Brown-Out Reset) to ensure recovery from firmware lock-ups. Avoid running PWM on the same pin shared with the ICSP programming interface (RB6/RB7) without isolation.
コンプライアンス情報
RoHS/REACH compliance status not explicitly stated in the verified distributor data; lead-free is typical for Microchip PIC18 industrial parts. Part is industrial-grade, NOT AEC-Q100 qualified - choose AEC-Q100 qualified PIC18 variants like PIC18F46K22-I/PT for automotive safety applications.
