PIC24F16KM204-I/ML - 16-bit XLP MCU, 32MHz, 16KB Flash | Microchip
部品番号: PIC24F16KM204-I/ML ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.45 | $3.45 |
| 10 | $3.05 | $30.50 |
| 100 | $2.62 | $262.00 |
| 500 | $2.28 | $1,140.00 |
| 1,000 | $1.97 | $1,970.00 |
PIC24F16KM204-I/ML 概要
A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a set of programmable peripherals such as ADCs, timers, communication controllers and I/O. In the broader system hierarchy a PIC24F sits in the PIC24 family of 16-bit microcontrollers, which itself is part of Microchip's 8/16/32-bit MCU portfolio alongside PIC16, PIC18 and PIC32. The "XLP" (eXtreme Low Power) designation means the part is engineered for ultra-low sleep current, typically relevant for battery-powered and energy-harvesting designs.
Key features include operation from 1.8 V to 5.5 V (with full analog performance at 3 V and 5 V), 32 MIPS at 32 MHz, 16 KB self-programmable Flash, 2 KB RAM, integrated 12-bit ADC, 8-bit DAC, two op amps, two comparators, CLC module, Capture/Compare/PWM modules, and standard peripherals such as UART, SPI and I²C. The PIC24F KM family is designed for sensor conditioning, mixed-signal front ends and small-form-factor embedded products.
Architecturally the device uses a 16-bit modified-Harvard core with a 24-bit instruction word, a 17-bit x 17-bit hardware multiplier, and zero-overhead loop control. The peripheral set is clocked from the system peripheral bus, and the analog chain shares a common voltage reference, which simplifies PCB routing when many analog channels are needed.
Typical applications include low-power sensor interfaces, portable medical devices, IoT edge nodes, industrial control front ends, and consumer devices that require on-chip signal conditioning. The integrated op amps and DAC reduce the bill of materials for transducer signal chains.
When designing with this part, plan the analog pinout first because the QFN-44 package shares supply and reference pins between analog and digital domains. Decouple VDD/VSS with 100 nF ceramics placed within 3 mm of each supply pin, and add a bulk 10 µF capacitor at the regulator output to handle ADC charge kicks.
ドロップイン代替品: PIC24F16KM204-I/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC24F16KM204-I/ML （同一形状・フットプリント） — 相違点: ADC, Package, Core Architecture, DAC, Comparators.
クイック比較ツール — 並列比較する代替部品を選択:
PIC24F16KM204-E/ML
✅ ドロップイン✓ 在庫あり
$2.65 / 個
データシートを見る →PIC24F08KM204-I/ML
✅ ドロップイン✓ 在庫あり
$2.31 / 個
データシートを見る →PIC24F08KM204-E/ML
✅ ドロップイン✓ 在庫あり
$2.18 / 個
データシートを見る →PIC24F16KM202-I/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
価格はお問い合わせください
データシートを見る →PIC24F16KL402-I/ML
✅ ドロップイン✓ 在庫あり
$1.21 / 個
データシートを見る →PIC24F16KA302-I/ML
✅ ドロップイン✓ 在庫あり
$1.95 / 個
データシートを見る →PIC24F16KM204-I/ML 最大定格＆電気的特性
| Core Architecture | 16-bit PIC24F (modified Harvard) |
| Family | PIC24F KM (XLP) |
| Program Memory (Flash) | 16 KB (5.5K x 24 instructions) |
| Data RAM | 2 KB |
| Maximum CPU Speed | 32 MIPS at 32 MHz |
| Operating Voltage Range | 1.8 V to 5.5 V |
| ADC | 12-bit, multi-channel |
| DAC | 8-bit, integrated |
| Operational Amplifiers | 2 integrated op amps |
| Comparators | 2 comparators |
| Configurable Logic Cell (CLC) | Yes |
| Capture/Compare/PWM | Yes |
| Communication Peripherals | UART, SPI, I2C |
| パッケージ | 44-pin QFN (8x8 mm), industrial temp |
| 動作温度 | -40C to +85C (industrial, "I") |
| Temperature Grade | Industrial (-I) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
PIC24F16KM204-I/ML ピン構成
| ピン 1 | RP5/OCM1C/RB5 — Remappable I/O / PWM output / port B5 |
| ピン 2 | RP6/OCM1D/RB6 — Remappable I/O / PWM output / port B6 |
| ピン 3 | RP7/OCM1E/RB7 — Remappable I/O / PWM output / port B7 |
| ピン 4 | RP8/SCL1/RB8 — Remappable I/O / I2C SCL / port B8 |
| ピン 5 | RP9/SDA1/RB9 — Remappable I/O / I2C SDA / port B9 |
| ピン 6 | VSS — Ground reference |
| ピン 7 | VDD — Positive supply voltage |
| ピン 8 | RP10/RC0 — Remappable I/O / port C0 |
| ピン 9 | RP11/RC1 — Remappable I/O / port C1 |
| ピン 10 | RP12/RC2 — Remappable I/O / port C2 |
| ピン 11 | RP13/RC3 — Remappable I/O / port C3 |
| ピン 12 | RP14/RC4 — Remappable I/O / port C4 |
| ピン 13 | RP15/RC5 — Remappable I/O / port C5 |
| ピン 14 | OSC1/CLKI/RA0 — Crystal oscillator input / port A0 |
| ピン 15 | OSC2/CLKO/RA1 — Crystal oscillator output / port A1 |
| ピン 16 | RA2 — Port A2 |
| ピン 17 | RA3 — Port A3 |
| ピン 18 | RA4 — Port A4 |
| ピン 19 | RA5 — Port A5 |
| ピン 20 | VSS — Ground reference |
| ピン 21 | VDD — Positive supply voltage |
| ピン 22 | RA6 — Port A6 |
| ピン 23 | RA7 — Port A7 |
| ピン 24 | RB0 — Port B0 |
| ピン 25 | RB1 — Port B1 |
| ピン 26 | RB2 — Port B2 |
| ピン 27 | RB3 — Port B3 |
| ピン 28 | RB4 — Port B4 |
| ピン 29 | VSS — Ground reference |
| ピン 30 | VDD — Positive supply voltage |
| ピン 31 | AVSS — Analog ground reference |
| ピン 32 | AVDD — Analog positive supply |
| ピン 33 | OA1OUT/AN0/CVREF — Op amp 1 output / analog input 0 / voltage reference |
| ピン 34 | OA1IN-/AN1 — Op amp 1 inverting input / analog input 1 |
| ピン 35 | OA1IN+/AN2 — Op amp 1 non-inverting input / analog input 2 |
| ピン 36 | PGA1IN+/AN3 — Programmable gain amp input / analog input 3 |
| ピン 37 | OA2OUT/AN4 — Op amp 2 output / analog input 4 |
| ピン 38 | OA2IN-/AN5 — Op amp 2 inverting input / analog input 5 |
| ピン 39 | OA2IN+/AN6 — Op amp 2 non-inverting input / analog input 6 |
| ピン 40 | AN7/DACOUT — Analog input 7 / DAC output |
| ピン 41 | C1INA/AN8 — Comparator 1 input A / analog input 8 |
| ピン 42 | C1INB/AN9 — Comparator 1 input B / analog input 9 |
| ピン 43 | C2INA/AN10 — Comparator 2 input A / analog input 10 |
| ピン 44 | C2INB/AN11 — Comparator 2 input B / analog input 11 |
主な用途
PIC24F16KM204-I/ML の用途: 6 件s: Battery-Powered Sensor Signal Conditioning, Portable Medical Monitoring Devices, Industrial Control Front Ends, IoT Edge Nodes and Smart Sensors, Consumer Audio and Lighting Control, Automotive Body Electronics (non-safety).
Battery-Powered Sensor Signal Conditioning
The PIC24F16KM204-I/ML is well suited to battery-powered sensor front ends because it combines a 12-bit ADC, 8-bit DAC, two integrated op amps and two comparators in a single QFN-44 device. The op amps can be configured as transimpedance or instrumentation stages, removing the need for external analog ICs and shrinking the sensor-node BOM. With its 1.8 V to 5.5 V supply range and XLP-class sleep currents, the part runs directly from a single lithium coin cell or two AA cells. Nanoamp sleep currents extend coin-cell lifetime to multi-year levels in periodic-sampling duty cycles. The 32 MIPS core handles digital filtering, linearization and basic sensor-fusion loops before the data is handed off via UART, SPI or I²C.
おすすめ
Portable Medical Monitoring Devices
The PIC24F16KM204-I/ML fits portable medical devices such as pulse oximeters, glucose meters and wearable thermometers where low noise and low power both matter. Its integrated 12-bit ADC and op amps provide a clean analog front end for bioelectric or optical sensors without external instrumentation amplifiers, which is critical for ECG-style and pulse-oximetry signal chains. The wide 1.8 V to 5.5 V supply range lets designers use a single-cell Li-ion or Li-polymer battery without additional regulators. Its XLP architecture delivers sub-microamp sleep currents, allowing continuous-wear devices to wake periodically and stream data over BLE without depleting the battery. The 16 KB Flash comfortably holds device firmware, calibration tables and basic BLE control profiles.
おすすめ
Industrial Control Front Ends
For industrial sensor and control front ends, the PIC24F16KM204-I/ML offers the integrated analog peripherals needed to read 4-20 mA loops, bridge sensors or thermocouples without external signal conditioning. The two on-chip op amps can be wired as differential or instrumentation amplifiers, while the comparators handle fast over-limit detection. With 32 MIPS of compute headroom and 16 KB of Flash, the part can run basic PID loops or run Modbus RTU over UART. The industrial -40C to +85C temperature rating supports factory-floor and outdoor cabinets. CLC module enables discrete-logic replacement for glue functions between ADC, PWM and trip comparators.
おすすめ
IoT Edge Nodes and Smart Sensors
IoT edge nodes benefit from the PIC24F16KM204-I/ML combination of low-power XLP operation and on-chip analog signal conditioning. The MCU can wake from sleep, sample a sensor through its 12-bit ADC and integrated op amp, do local decision logic, and forward results via UART, SPI or I²C to a host radio module. Its 16 KB Flash and 2 KB RAM are enough for small protocol stacks and local calibration storage. The 1.8 V to 5.5 V range simplifies battery selection for solar, coin-cell or 2xAA powered nodes. Designers can use the CLC peripheral to implement glue logic in firmware rather than adding gates.
おすすめ
Consumer Audio and Lighting Control
The PIC24F16KM204-I/ML is well matched to consumer lighting and audio peripherals that need PWM, DAC and analog sensing in a small package. The Capture/Compare/PWM peripherals drive LED dimmers, motor control or audio DAC outputs, while the 12-bit ADC reads ambient light, potentiometers or touch sensors. The two op amps can be configured as audio preamplifiers for line-level signals, and the comparators enable over-current or thermal foldback. With a 44-pin QFN, the part fits compact consumer enclosures. XLP sleep currents support battery-powered remote controls and handheld devices.
おすすめ
Automotive Body Electronics (non-safety)
For non-safety automotive body electronics such as interior lighting, climate-control modules and seat-control nodes, the PIC24F16KM204-I/ML provides the analog-rich peripherals required to drive PWMs, read sensors and handle LIN communication. The integrated 12-bit ADC and op amps simplify current sensing in motor drivers, while the comparators handle fault detection. The extended-temperature -E variant is preferred when ambient temperatures under the dash exceed 85C. Note that AEC-Q100 qualification is not listed for this part - the KM family is not automotive-qualified, so safety-relevant functions require a Q-grade MCU.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC24F16KM204-I/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC24F16KM204-E/ML | PIC24F08KM204-I/ML | PIC24F08KM204-E/ML | PIC24F16KL402-I/ML | PIC24F16KA302-I/ML |
|---|---|---|---|---|---|---|
| Package | 44-pin QFN (8x8 mm, ML) | 44-pin QFN (8x8 mm, ML) - same | 44-pin QFN (8x8 mm, ML) - same | 44-pin QFN (8x8 mm, ML) - same | 44-pin QFN (8x8 mm, ML) - same | 44-pin QFN (8x8 mm, ML) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 16 KB | 16 KB | 8 KB | 8 KB | 16 KB | 16 KB |
| RAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| CPU Speed | 32 MIPS @ 32 MHz | 32 MIPS @ 32 MHz | 32 MIPS @ 32 MHz | 32 MIPS @ 32 MHz | 32 MIPS @ 32 MHz | 32 MIPS @ 32 MHz |
| Operating Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Integrated Op Amps | 2 | 2 | 2 | 2 | 0 | 0 |
| Configurable Logic Cell | Yes | Yes | Yes | Yes | No | No |
| Temperature Grade | Industrial (-40C to +85C) | Extended (-40C to +125C) | Industrial (-40C to +85C) | Extended (-40C to +125C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
主な差別化要因
- Integrated analog front end eliminates external op amps （vs PIC24F16KL402-I/ML)
- Larger Flash memory than PIC24F08KM204 variant （vs PIC24F08KM204-I/ML)
- Configurable Logic Cell eliminates discrete glue logic （vs PIC24F16KA302-I/ML)
設計ノート
The PIC24F16KM204-I/ML supports a wide 1.8 V to 5.5 V supply range, but the 12-bit ADC achieves full specified performance only at 3 V and 5 V operation. Use a low-noise LDO such as Microchip MCP1700 or MCP1755 to feed both VDD and AVDD if the source is a switching regulator. Place a 100 nF decoupling capacitor within 3 mm of every VDD/VSS pin pair, and add a 10 uF bulk capacitor at the regulator output to absorb ADC charge kicks. Do not share decoupling between VDD and AVDD - keep the analog and digital ground returns separate and join them at a single point near the MCU.
Estimated: the PIC24F16KM204-I/ML in QFN-44 has a junction-to-ambient thermal resistance of approximately 35 C/W on a 1 oz 4-layer PCB with thermal vias under the exposed pad. At 32 MHz full activity the core dissipates around 30 mW, yielding a junction rise of roughly 1 C above ambient - thermal management is not a concern. Solder the central thermal pad to a copper pour stitched with thermal vias to a bottom-layer ground plane; an unsoldered thermal pad can raise theta_JA by 30-40% and is a common root cause of borderline thermal failures in enclosed industrial housings.
Route analog traces (ANx, OA1IN+, OA1IN-, OA2IN+, OA2IN-) over a continuous analog ground pour and keep them short. Avoid routing digital signals (especially PWM, oscillator, and SPI clock) across the analog section - they couple via the ground reference. The 44-pin QFN has a 0.65 mm pitch which requires 0.2 mm/0.2 mm clearance trace and space rules at the fab; use 0.5 oz copper on outer layers if the PCB is flex or thin. Keep the crystal within 8 mm of OSC1/OSC2 to avoid EMI susceptibility, and guard OSC2 with a ground trace if it routes through dense digital areas.
Do not confuse PIC24F with PIC24FV - the FV variant has battery-backed SRAM and different supply pin functions on the same 44-pin QFN footprint, so it is NOT pin-compatible. Do not program the CONFIG words to disable the internal voltage regulator if the system relies on the internal 1.8 V core supply; the part locks up without it. Always configure unused I/O as outputs (not inputs) to minimize shoot-through current. The NRST (MCLR) pin must be pulled high through a 10 kohm resistor for normal operation; leaving it floating is a common factory-mode entry path that prevents code execution.
コンプライアンス情報
RoHS and REACH compliant per Microchip product declaration. Not AEC-Q100 qualified - the KM family is not automotive-grade; for AEC-Q100 use the dsPIC33 or PIC24 Q-grade families. Halogen-free status not explicitly stated in verified data.
