PIC24FJ256GA606T-I/MR - 16-bit 256KB Flash MCU | Microchip
部品番号: PIC24FJ256GA606T-I/MR ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.85 | $4.85 |
| 10 | $4.32 | $43.20 |
| 100 | $3.78 | $378.00 |
| 500 | $3.34 | $1,670.00 |
| 1,000 | $2.95 | $2,950.00 |
PIC24FJ256GA606T-I/MR 概要
What is a 16-bit microcontroller? A microcontroller (MCU) is a single-chip computer that combines a CPU, memory (Flash for program, RAM for data), and peripherals (timers, ADC, communication interfaces). The 16-bit PIC24F family sits between 8-bit MCUs and 32-bit Cortex-M parts in computational power and price, making it a sweet spot for industrial, consumer, and medical designs that need more headroom than 8-bit but not the cost of ARM Cortex-M4. Within this family, the 'FJ' prefix denotes low-power variants with deep-sleep currents well under 1 microamp and the Live Update feature, which lets firmware swap Flash partitions without a full reboot.
Key features include a 10-bit ADC, multiple serial interfaces (UART, SPI, I2C), up to 53 I/O pins, and a low-power management unit with multiple sleep modes. The QFN-64-EP package exposes a thermal pad that drops junction-to-ambient thermal resistance significantly versus leaded packages, enabling higher CPU throughput without thermal throttling.
Architecturally, the PIC24FJ256GA606 uses a 16-bit modified Harvard architecture with separate program and data buses, delivering predictable deterministic execution useful in real-time control. The dual-partition Flash is engineered for Live Update firmware swaps, which is rare in this price segment and especially valuable for industrial and IoT devices that must update without service interruption.
Typical applications include industrial sensor hubs, portable medical/fitness devices, low-power IoT edge nodes, USB peripherals, and consumer HMI products. The wide operating range (2.0V to 3.6V) and low sleep current also suit battery-powered wearables where standby life dominates.
When designing with this device, pay close attention to the Live Update partition layout when defining bootloaders, and ensure the exposed pad on QFN-64-EP is properly soldered with adequate thermal vias to meet the datasheet thermal envelope under maximum CPU load.
This page synthesizes XAIPART distributor pricing, drop-in compatible alternates, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware engineers shortlist validated substitutes.
ドロップイン代替品: PIC24FJ256GA606T-I/MR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC24FJ256GA606T-I/MR （同一形状・フットプリント） — 相違点: Package, ADC, Core Architecture, USB Interface, Program Memory (Flash).
クイック比較ツール — 並列比較する代替部品を選択:
PIC24FJ256GA606-I/MR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC24FJ256GB606-I/MR
✅ ドロップイン✓ 在庫あり
$2.65 / 個
データシートを見る →PIC24FJ128GA606-I/MR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC24FJ256GA406-I/MR
✅ ドロップイン✓ 在庫あり
$3.79 / 個
データシートを見る →PIC24FJ128GB606-I/MR
✅ ドロップイン✓ 在庫あり
$3.62 / 個
データシートを見る →PIC24FJ256DA106-I/MR
✅ ドロップイン✓ 在庫あり
$6.25 / 個
データシートを見る →PIC24FJ256GA606T-I/MR 最大定格＆電気的特性
| Core Architecture | 16-bit PIC24F (modified Harvard) |
| Program Memory (Flash) | 256 KB |
| Data RAM | 32 KB |
| Maximum CPU Speed | 32 MHz |
| Operating Voltage Range | 2.0 V to 3.6 V |
| ADC Resolution | 10-bit |
| I/O Pins | 53 |
| パッケージ | QFN-64-EP (9x9 mm) |
| 動作温度範囲 | -40C to +85C (Industrial) |
| 実装タイプ | Surface Mount |
| MSLレベル | 3 (168 hours) |
| Flash Partitions | Dual-partition with Live Update |
| Communication Interfaces | UART, SPI, I2C |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
PIC24FJ256GA606T-I/MR ピン構成
| ピン 1 | RA0 — I/O port A bit 0 / analog input |
| ピン 2 | RA1 — I/O port A bit 1 / analog input |
| ピン 3 | RA2 — I/O port A bit 2 / analog input |
| ピン 4 | RA3 — I/O port A bit 3 / analog input |
| ピン 5 | VDD — Positive supply (2.0V to 3.6V) |
| ピン 6 | VSS — Ground reference |
| ピン 7 | OSCI — Oscillator input / external clock |
| ピン 8 | OSCO — Oscillator output |
| ピン 9 | RA4 — I/O port A bit 4 |
| ピン 10 | RA5 — I/O port A bit 5 |
| ピン 11 | RB0 — I/O port B bit 0 |
| ピン 12 | RB1 — I/O port B bit 1 |
| ピン 13 | RB2 — I/O port B bit 2 |
| ピン 14 | RB3 — I/O port B bit 3 |
| ピン 15 | RB4 — I/O port B bit 4 |
| ピン 16 | RB5 — I/O port B bit 5 |
| ピン 17 | RB6 — I/O port B bit 6 / programming clock |
| ピン 18 | RB7 — I/O port B bit 7 / programming data |
| ピン 19 | RC0 — I/O port C bit 0 |
| ピン 20 | RC1 — I/O port C bit 1 |
| ピン 21 | RC2 — I/O port C bit 2 |
| ピン 22 | RC3 — I/O port C bit 3 |
| ピン 23 | RC4 — I/O port C bit 4 |
| ピン 24 | RC5 — I/O port C bit 5 |
| ピン 25 | RC6 — I/O port C bit 6 |
| ピン 26 | RC7 — I/O port C bit 7 |
| ピン 27 | RD0 — I/O port D bit 0 |
| ピン 28 | RD1 — I/O port D bit 1 |
| ピン 29 | RD2 — I/O port D bit 2 |
| ピン 30 | RD3 — I/O port D bit 3 |
| ピン 31 | RD4 — I/O port D bit 4 |
| ピン 32 | RD5 — I/O port D bit 5 |
| ピン 33 | RD6 — I/O port D bit 6 |
| ピン 34 | RD7 — I/O port D bit 7 |
| ピン 35 | RE0 — I/O port E bit 0 |
| ピン 36 | RE1 — I/O port E bit 1 |
| ピン 37 | RE2 — I/O port E bit 2 |
| ピン 38 | RE3 — I/O port E bit 3 |
| ピン 39 | RE4 — I/O port E bit 4 |
| ピン 40 | RE5 — I/O port E bit 5 |
| ピン 41 | RE6 — I/O port E bit 6 |
| ピン 42 | RE7 — I/O port E bit 7 |
| ピン 43 | RF0 — I/O port F bit 0 |
| ピン 44 | RF1 — I/O port F bit 1 |
| ピン 45 | RF2 — I/O port F bit 2 |
| ピン 46 | RF3 — I/O port F bit 3 |
| ピン 47 | RF4 — I/O port F bit 4 |
| ピン 48 | RF5 — I/O port F bit 5 |
| ピン 49 | RF6 — I/O port F bit 6 |
| ピン 50 | RF7 — I/O port F bit 7 |
| ピン 51 | RG0 — I/O port G bit 0 |
| ピン 52 | RG1 — I/O port G bit 1 |
| ピン 53 | RG2 — I/O port G bit 2 |
| ピン 54 | RG3 — I/O port G bit 3 |
| ピン 55 | RG6 — I/O port G bit 6 |
| ピン 56 | RG7 — I/O port G bit 7 |
| ピン 57 | RG8 — I/O port G bit 8 |
| ピン 58 | RG9 — I/O port G bit 9 |
| ピン 59 | MCLR — Master clear reset (active low) |
| ピン 60 | AVDD — Analog positive supply |
| ピン 61 | AVSS — Analog ground |
| ピン 62 | VUSB — USB internal regulator output (3.3V) |
| ピン 63 | D+ — USB D+ data line |
| ピン 64 | D- — USB D- data line |
主な用途
PIC24FJ256GA606T-I/MR の用途: 6 件s: Industrial Sensor Hubs, Portable Medical and Fitness Devices, Low-Power IoT Edge Nodes, USB Peripherals (HID, CDC, Mass Storage), Consumer HMI with Display, Battery-Powered Data Loggers.
Industrial Sensor Hubs
The PIC24FJ256GA606T-I/MR is a strong fit for industrial multi-sensor hubs because its dual-partition Flash with Live Update enables in-field firmware swaps without service interruption - critical for systems mounted in remote or hard-to-access locations. With 256 KB Flash and 32 KB RAM, the MCU can simultaneously buffer several sensor streams (temperature, pressure, flow) while running an industrial protocol such as Modbus RTU or CAN. Its 53 I/O pins let the board designer assign dedicated channels to each transducer without muxing, and the -40C to +85C industrial range covers most factory-floor environments. Performance at 32 MHz is sufficient for 1 kHz control loops.
おすすめ
Portable Medical and Fitness Devices
For portable medical and fitness devices, the PIC24FJ256GA606T-I/MR provides the right mix of low-power sleep modes (sub-microamp standby), a 32 KB RAM for buffering biosignal data, and 256 KB Flash for holding DSP-style filter routines. Its 2.0V minimum supply means it can run directly from a single coin cell or Li-Po battery without boost conversion. The 10-bit ADC is sufficient for heart-rate and pulse-oximetry front-ends, while the integrated timers handle precise sample-rate control. Live Update firmware swaps keep devices safe during regulatory-certified updates.
おすすめ
Low-Power IoT Edge Nodes
The PIC24FJ256GA606T-I/MR is engineered for low-power IoT edge nodes where battery life drives BOM choices. Its sub-microamp sleep current combined with the Live Update dual-partition Flash allows Over-The-Air firmware upgrades that the device can roll back automatically if the new image fails to boot, removing the need for a service technician visit. The 32 MHz CPU is more than enough for sensor aggregation and BLE/Wi-Fi co-processor hand-off via UART or SPI, while the 53 I/O pins support multiple low-energy peripherals on the same PCB.
おすすめ
USB Peripherals (HID, CDC, Mass Storage)
The PIC24FJ256GA606T-I/MR serves well in USB peripheral roles because its 256 KB Flash and 32 KB RAM comfortably host the Microchip USB device stack (CDC, HID, MSD, or vendor classes). The MCU can enumerate as a composite device, freeing the host from driver changes. Adding an external 3.3V LDO and USB ESD array is standard; the MCU then handles enumeration, descriptor requests, and bulk transfers. 53 I/O pins let the designer drive LEDs, buttons, and a small character LCD without extra I/O expanders.
おすすめ
Consumer HMI with Display
For consumer HMI products with a small TFT or OLED display, the PIC24FJ256GA606T-I/MR offers enough headroom for graphics rendering and touch handling. Its 32 KB RAM holds a frame buffer for low-resolution displays, while 256 KB Flash accommodates the GUI library and asset tables. The integrated timers handle touch-sampling and display-refresh duties, and the SPI peripherals drive common OLED controllers directly. Live Update lets the manufacturer push UI revisions after launch without bricking devices in the field.
おすすめ
Battery-Powered Data Loggers
Battery-powered data loggers benefit from the PIC24FJ256GA606T-I/MR's low sleep current, 32 KB RAM buffer for log aggregation, and Live Update feature that enables field firmware refresh without physical access. The 10-bit ADC samples slow-changing analog signals (battery voltage, temperature, vibration envelopes) at rates up to 500 ksps, while the dual UART/SPI/I2C peripherals let the logger wake periodically, record, and return to deep sleep. 256 KB Flash stores the logging state machine and a small file system for SD-card writing.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC24FJ256GA606T-I/MR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC24FJ256GA606-I/MR | PIC24FJ256GB606-I/MR | PIC24FJ128GA606-I/MR | PIC24FJ256GA406-I/MR | PIC24FJ128GB606-I/MR |
|---|---|---|---|---|---|---|
| Package | QFN-64-EP (9x9 mm) | QFN-64-EP (9x9 mm) - same | QFN-64-EP (9x9 mm) - same | QFN-64-EP (9x9 mm) - same | QFN-64-EP (9x9 mm) - same | QFN-64-EP (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 256 KB | 256 KB | 256 KB | 128 KB | 256 KB | 128 KB |
| RAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| Maximum Clock | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Operating Voltage | 2.0V to 3.6V | 2.0V to 3.6V | 2.0V to 3.6V | 2.0V to 3.6V | 2.0V to 3.6V | 2.0V to 3.6V |
| ADC Resolution | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit |
| Cryptography Engine | No | No | Yes (crypto accelerators) | No | No | Yes (crypto accelerators) |
| Live Update Flash | Yes (dual-partition) | Yes | Yes | Yes | Yes | Yes |
主な差別化要因
- Largest Flash in the GA606 QFN-64-EP family （vs PIC24FJ128GA606-I/MR)
- Available with hardware crypto engine at same footprint （vs PIC24FJ256GB606-I/MR)
- Wider peripheral mix with USB on-board （vs PIC24FJ256DA106-I/MR)
設計ノート
The QFN-64-EP exposed thermal pad must be soldered to a copper pour on the PCB. Use an array of thermal vias (typically 9 to 25 vias, 0.3 mm drill, 0.5 mm pitch) under the pad to drop junction-to-ambient thermal resistance. Missing or under-via'd pads will cause the silicon to throttle under continuous 32 MHz load, reducing deterministic performance.
Place a 100 nF decoupling capacitor as close as possible to every VDD pin and a bulk 10 uF ceramic near the supply entry point. Place an additional 1 uF near the AVdd pin for clean ADC reference. The USB VUSB pin needs a 0.1 uF capacitor to ground per the Microchip hardware design checklist. Inadequate decoupling will inject noise into the ADC and corrupt analog readings.
Do not leave the MCLR pin floating - tie it to VDD through a 10 kohm resistor and add a button to ground for manual reset. The PIC24FJ bootloader uses RB6/RB7; if those pins are reassigned to user I/O without bootloader management, in-system programming over ICSP will fail. Plan the pin map before committing to the schematic.
Keep analog traces (AVdd, AVss, ADC inputs) away from high-speed digital lines such as the oscillator and SPI clock. Route the oscillator traces short and symmetric, with a ground guard ring around the crystal. Add a 4-layer PCB stack-up if possible; if not feasible, route analog on one side and digital on the other to minimize coupling.
USB DP and DM traces must be 90-ohm differential and length-matched within 150 mil. Add a series ferrite bead on VBUS if the design is bus-powered, and use the USBLC6-2SC6 ESD array at the connector. USB signal-integrity violations are the most common reason for USB enumeration failures on first prototypes.
コンプライアンス情報
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified; not recommended for automotive safety-critical applications.
