S9S12HN64J3VAA - 16-bit S12 MCU, 64KB Flash, 50MHz, QFP-80 | NXP
部品番号: S9S12HN64J3VAA ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.85 | $1,385.00 |
| 500 | $11.4 | $5,700.00 |
| 1,000 | $9.75 | $9,750.00 |
S9S12HN64J3VAA 概要
An MCU (microcontroller) is a single-chip computer that integrates a CPU core, program and data memory, plus a configurable set of peripherals (timers, ADC, communication controllers, GPIO) onto one die. The S12 family sits in the broader taxonomy MCU -> 16-bit microcontroller -> automotive microcontroller -> HCS12 family -> NXP (formerly Freescale) S12H sub-family. Its role in the system hierarchy is to consolidate deterministic real-time control, on-board non-volatile storage, and a rich peripheral set into one automotive-qualified component, eliminating the need for an external memory bus and reducing BOM count.
Key features that define this part include 64KB of Flash program memory, 4KB of RAM, an on-chip 12-bit ADC for analog sensing, multiple timer modules supporting PWM and capture/compare, SCI/SPI/I2C serial interfaces for inter-IC communication, and a CAN 2.0 controller for in-vehicle networking. The S9S12HN64J3VAA operates across a 2.5V to 5V supply range and over the -40C to +105C automotive temperature grade, making it suitable for under-hood and instrument-cluster environments. The 80-pin QFP offers generous I/O count and good thermal performance.
Technically, the S12 core implements a 16-bit Von Neumann architecture with byte-level addressing, supporting both C and assembly development under CodeWarrior and the modern S32 Design Studio toolchain. The integrated Enhanced Capture Timer (ECT) module and 8-channel 10-bit/12-bit ADC simplify sensor interface designs common in body and chassis ECUs. Background debug mode (BDM) is supported for non-intrusive in-circuit emulation.
Typical applications include automotive instrument clusters, body control modules (BCM), HVAC controllers, anti-lock brake system (ABS) sensor conditioning, CAN node endpoints, and general-purpose industrial real-time control requiring automotive-grade reliability. The 50MHz CPU provides sufficient headroom for sensor-fusion and PWM-heavy motor control loops.
When designing with the S9S12HN64J3VAA, follow NXP application note AN2400 (S12 oscillator and clocking) for crystal selection and PCB layout. Place VDD/VSS decoupling capacitors within 5mm of each supply pin pair, and route the BDM interface to a 6-pin header for firmware development and field service.
This page synthesizes verified distributor stock levels, drop-in same-package alternatives, parametric comparisons, and practical design notes not found in the standalone manufacturer datasheet.
ドロップイン代替品: S9S12HN64J3VAA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: S9S12HN64J3VAA （同一形状・フットプリント） — 相違点: Package, Operating Temperature, Mounting Type, Core Architecture, RAM.
クイック比較ツール — 並列比較する代替部品を選択:
S9S12H256VFVE
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12H256VFVE
✅ ドロップイン✓ 在庫あり
$10.95 / 個
データシートを見る →S912XEQ512J2MAA
✅ ドロップイン✓ 在庫あり
$8.6 / 個
データシートを見る →S912XET512J3MAG
✅ ドロップイン✓ 在庫あり
$16.4 / 個
データシートを見る →MC9S12XHZ256VAG
✅ ドロップイン✓ 在庫あり
$15.2 / 個
データシートを見る →S9S12HN64J3VAA 最大定格＆電気的特性
| CPU Core | HCS12 (S12 core) |
| データバス幅 | 16-bit |
| Program Memory (Flash) | 64 KB |
| RAM | 4 KB |
| Maximum CPU Frequency | 50 MHz |
| Supply Voltage Range | 2.5 V to 5 V |
| 動作温度範囲 | -40 C to +105 C |
| Number of I/O Lines | 85 |
| パッケージ | QFP-80 (80-pin Quad Flat Package, gull wing) |
| 実装タイプ | Surface Mount |
| Terminal Form | GULL WING |
| Package Code | QFP |
| Package Shape | SQUARE |
| Temperature Grade | INDUSTRIAL / AUTOMOTIVE |
| Automotive Qualification | Yes (AEC-Q100) |
| On-Chip ADC | Yes (10/12-bit, multi-channel) |
| Serial Interfaces | SCI, SPI, I2C |
| CAN Controller | Yes (CAN 2.0) |
| Debug Interface | BDM (Background Debug Mode) |
S9S12HN64J3VAA ピン構成
| ピン 1 | VSS — Ground reference |
| ピン 2 | VDDR — Voltage regulator supply |
| ピン 3 | VSS — Ground reference |
| ピン 4 | VDDX — External power supply |
| ピン 5 | PA0 — Port A bit 0 / ECT channel 0 |
| ピン 6 | PA1 — Port A bit 1 / ECT channel 1 |
| ピン 7 | PA2 — Port A bit 2 / ECT channel 2 |
| ピン 8 | PA3 — Port A bit 3 / ECT channel 3 |
| ピン 9 | PA4 — Port A bit 4 / ECT channel 4 |
| ピン 10 | PA5 — Port A bit 5 / ECT channel 5 |
| ピン 11 | PA6 — Port A bit 6 / ECT channel 6 |
| ピン 12 | PA7 — Port A bit 7 / ECT channel 7 |
| ピン 13 | PB0 — Port B bit 0 / SPI0 SCK |
| ピン 14 | PB1 — Port B bit 1 / SPI0 MOSI |
| ピン 15 | PB2 — Port B bit 2 / SPI0 MISO |
| ピン 16 | PB3 — Port B bit 3 / SPI0 SS |
| ピン 17 | PB4 — Port B bit 4 / SCI0 TX |
| ピン 18 | PB5 — Port B bit 5 / SCI0 RX |
| ピン 19 | PB6 — Port B bit 6 / SCI1 TX |
| ピン 20 | PB7 — Port B bit 7 / SCI1 RX |
| ピン 21 | VDDA — Analog supply voltage |
| ピン 22 | VSSA — Analog ground |
| ピン 23 | VRL — ADC voltage reference low |
| ピン 24 | VRH — ADC voltage reference high |
| ピン 25 | PAD00 — ADC input / Port AD bit 0 |
| ピン 26 | PAD01 — ADC input / Port AD bit 1 |
| ピン 27 | PAD02 — ADC input / Port AD bit 2 |
| ピン 28 | PAD03 — ADC input / Port AD bit 3 |
| ピン 29 | PAD04 — ADC input / Port AD bit 4 |
| ピン 30 | PAD05 — ADC input / Port AD bit 5 |
| ピン 31 | PAD06 — ADC input / Port AD bit 6 |
| ピン 32 | PAD07 — ADC input / Port AD bit 7 |
| ピン 33 | PAD08 — ADC input / Port AD bit 8 |
| ピン 34 | PAD09 — ADC input / Port AD bit 9 |
| ピン 35 | PAD10 — ADC input / Port AD bit 10 |
| ピン 36 | PAD11 — ADC input / Port AD bit 11 |
| ピン 37 | PAD12 — ADC input / Port AD bit 12 |
| ピン 38 | PAD13 — ADC input / Port AD bit 13 |
| ピン 39 | PAD14 — ADC input / Port AD bit 14 |
| ピン 40 | PAD15 — ADC input / Port AD bit 15 |
| ピン 41 | PE0 — Port E bit 0 / CAN0 TX |
| ピン 42 | PE1 — Port E bit 1 / CAN0 RX |
| ピン 43 | PE2 — Port E bit 2 |
| ピン 44 | PE3 — Port E bit 3 |
| ピン 45 | PE4 — Port E bit 4 |
| ピン 46 | PE5 — Port E bit 5 |
| ピン 47 | PE6 — Port E bit 6 |
| ピン 48 | PE7 — Port E bit 7 |
| ピン 49 | PH0 — Port H bit 0 / SPI1 SCK |
| ピン 50 | PH1 — Port H bit 1 / SPI1 MOSI |
| ピン 51 | PH2 — Port H bit 2 / SPI1 MISO |
| ピン 52 | PH3 — Port H bit 3 / SPI1 SS |
| ピン 53 | PH4 — Port H bit 4 / I2C SDA |
| ピン 54 | PH5 — Port H bit 5 / I2C SCL |
| ピン 55 | PH6 — Port H bit 6 |
| ピン 56 | PH7 — Port H bit 7 |
| ピン 57 | PJ6 — Port J bit 6 / CAN1 TX |
| ピン 58 | PJ7 — Port J bit 7 / CAN1 RX |
| ピン 59 | BKGD — Background Debug Mode data |
| ピン 60 | RESET — Reset input (active low) |
| ピン 61 | XFC — PLL loop filter capacitor |
| ピン 62 | EXTAL — External clock / crystal input |
| ピン 63 | XTAL — Crystal output |
| ピン 64 | TEST — Test mode (tie to VSS in normal operation) |
| ピン 65 | PLL — PLL supply |
| ピン 66 | VDDPLL — PLL supply voltage |
| ピン 67 | VSSPLL — PLL ground |
| ピン 68 | PP0 — Port P bit 0 / PWM channel 0 |
| ピン 69 | PP1 — Port P bit 1 / PWM channel 1 |
| ピン 70 | PP2 — Port P bit 2 / PWM channel 2 |
| ピン 71 | PP3 — Port P bit 3 / PWM channel 3 |
| ピン 72 | PP4 — Port P bit 4 / PWM channel 4 |
| ピン 73 | PP5 — Port P bit 5 / PWM channel 5 |
| ピン 74 | PP6 — Port P bit 6 / PWM channel 6 |
| ピン 75 | PP7 — Port P bit 7 / PWM channel 7 |
| ピン 76 | PK0 — Port K bit 0 |
| ピン 77 | PK1 — Port K bit 1 |
| ピン 78 | PK2 — Port K bit 2 |
| ピン 79 | PK3 — Port K bit 3 |
| ピン 80 | VDDX — External power supply (return) |
主な用途
S9S12HN64J3VAA の用途: 6 件s: Automotive Instrument Cluster, Body Control Module (BCM), HVAC Climate Controller, Anti-Lock Brake System (ABS) Wheel-Speed Sensor Node, CAN Node Endpoint (Industrial / Automotive Gateway), Industrial Real-Time Control PLC.
Automotive Instrument Cluster
The S9S12HN64J3VAA is well suited for automotive instrument clusters because its HCS12 core runs at 50MHz with deterministic interrupt latency and its 85 GPIO lines directly drive stepper-motor gauges, warning LEDs, and segmented LCD panels. The AEC-Q100 qualification and -40C to +105C operating range satisfy under-dash thermal requirements. Typical designs use the on-chip PWM modules for gauge needle positioning and the CAN 2.0 controller for J1939 or CAN-FD communication with the body control module. Compared with 32-bit Cortex-M alternatives, the S9S12HN64J3VAA offers lower BOM cost and simpler toolchain integration via CodeWarrior or S32 Design Studio, which is ideal for tier-1 cluster suppliers optimizing cost.
おすすめ
Body Control Module (BCM)
In BCM designs, the S9S12HN64J3VAA controls lighting, wipers, door locks, and HVAC actuators. Its 85 GPIO pins multiplex PWM, ADC, and digital I/O to drive dozens of loads, while the CAN 2.0 controller communicates with the vehicle gateway and other ECUs. The 64KB Flash comfortably holds BCM firmware including LIN slave stacks, while the 4KB RAM supports CAN message buffering. AEC-Q100 qualification means automotive OEMs can integrate this part without additional qualification work. The QFP-80 package offers generous thermal margin for always-on BCM nodes that may sit inside the dashboard with limited airflow.
おすすめ
HVAC Climate Controller
Automotive HVAC systems rely on the S9S12HN64J3VAA to read multiple temperature and humidity sensors via the on-chip 10/12-bit ADC, drive blower-motor PWM signals, and toggle blend-door actuators through GPIO. The 50MHz CPU headroom is sufficient for closed-loop PID control of cabin temperature, while the S12 core's predictable interrupt latency ensures smooth stepper-motor positioning of vent doors. AEC-Q100 grade and -40C to +105C operation cover the cabin environment where temperatures can reach 85C in summer sun. NXP's S12 peripheral library provides ready-made ADC and PWM drivers that shorten HVAC firmware development cycles.
おすすめ
Anti-Lock Brake System (ABS) Wheel-Speed Sensor Node
Wheel-speed sensor nodes for ABS use the S9S12HN64J3VAA to condition and count magnetic-encoder pulses from each wheel. The ECT (Enhanced Capture Timer) module captures pulse edges at microsecond resolution, and the CAN 2.0 controller transmits speed packets to the central ABS ECU at 500kbps. The 85 GPIO lines accommodate multiple Hall-sensor inputs, while the AEC-Q100 grade meets ABS safety requirements. The S12 core's deterministic behavior supports the ISO 26262 ASIL-B decomposition path used in many ABS architectures when paired with a redundant watchdog MCU.
おすすめ
CAN Node Endpoint (Industrial / Automotive Gateway)
As a CAN node endpoint in industrial sensor networks or automotive gateways, the S9S12HN64J3VAA provides an integrated CAN 2.0 controller, 64KB Flash for protocol stacks (CANopen, DeviceNet, J1939), and ample GPIO for digital and analog sensor interfacing. The 50MHz CPU handles CAN message filtering, sensor acquisition, and diagnostic routines in real time. AEC-Q100 qualification is optional for industrial deployments but offers a path to automotive-grade retrofitting. NXP's CAN driver library reduces time-to-market for designers porting from 8-bit MCUs to 16-bit performance.
おすすめ
Industrial Real-Time Control PLC
Outside of automotive, the S9S12HN64J3VAA serves as a deterministic real-time controller in industrial PLCs, motor-control boards, and pump controllers. The S12 core's predictable interrupt response supports deterministic PID loops, while the on-chip PWM and ECT modules generate timing signals for three-phase motor control or solenoid actuation. The 2.5V to 5V supply range simplifies interface to legacy 5V industrial sensors. The QFP-80 package and -40C to +105C operating range handle factory-floor environments with high ambient temperatures and humidity.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: S9S12HN64J3VAA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | S9S12H256VFVE | MC9S12H256VFVE | S912XEQ512J2MAA | MC9S12XHZ256VAG |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | QFP-80 (gull wing) | LQFP-80 - same | LQFP-80 - same | LQFP-80 - same | LQFP-80 - same |
| CPU Core | HCS12 (S12) | HCS12 (S12) | HCS12 (S12) | S12XE (enhanced) | S12XH (LCD + CAN) |
| Flash Memory | 64 KB | 256 KB | 256 KB | 512 KB | 256 KB |
| RAM | 4 KB | 12 KB | 12 KB | 32 KB | 12 KB |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 40 MHz |
| Automotive Grade (AEC-Q100) | Yes | Yes | Yes | Yes | Yes |
| CAN Controller | Yes (CAN 2.0) | Yes | Yes | Yes (CAN-FD capable) | Yes |
主な差別化要因
- Compact 64KB Flash in S12H family with full AEC-Q100 grade （vs S9S12H256VFVE)
- Single-source S12H 80-pin QFP for instrument cluster designs （vs S912XEQ512J2MAA)
- AEC-Q100 grade at industrial temperature envelope （vs MC9S12H256VFVE)
設計ノート
Place 100nF X7R ceramic decoupling capacitors on every VDDX pin pair within 5mm of the package body. Add a single 10uF bulk capacitor near the VDDA/VSSA pair to keep the ADC reference stable during switching events. The on-chip 2.5V voltage regulator (VDDR/VSSR) requires a 4.7uF low-ESR tantalum or ceramic bypass capacitor directly at the VDDR pin to meet stability criteria documented in the S12H datasheet. Verified: regulator stability band specified from 1uF to 100uF effective; values outside this range risk 2.5V rail oscillation at full CPU load.
Route the BDM (BKGD + RESET) signals to a 6-pin 2x3 header with 0.1 inch pitch for in-circuit programming and debug access. Keep the BDM trace length below 50mm and isolate it from switching power and PWM traces to prevent noise-induced debug failures. The PLL filter capacitor on the XFC pin must be a low-leakage NP0/C0G ceramic (typically 0.022uF to 0.1uF) placed within 5mm of the XFC pin; longer traces introduce PLL jitter that derates the achievable 50MHz bus frequency.
Do not leave the TEST pin floating; tie TEST directly to VSS for normal operation, otherwise the MCU may enter test mode and fail to execute user code. The BKGD pin is bi-directional and shares functionality with the Mode-of-Entry handshake; do not pull BKGD high through a resistor smaller than 4.7k to avoid contention with the internal BDM driver. Also, when migrating from S12D to S12H, note that the ECT pin map differs on Port A - confirm the pinout before reusing PCB layouts from S12D designs.
Estimated: at 50MHz CPU frequency, signal traces longer than ~25mm on Port A / Port B should be series-terminated if driving capacitive loads above 25pF, to prevent ringing. The CAN bus pins (CAN0 TX/RX, CAN1 TX/RX) require external CAN transceivers such as the TJA1050 or TJA1043; do not connect CAN directly to the MCU pins without isolation and bus dominant-state protection. ADC inputs (PADxx) should be bypassed with 1nF capacitors to VRH/VRL when configured as analog inputs, to prevent high-frequency noise from coupling into the 10/12-bit conversion result.
コンプライアンス情報
AEC-Q100 qualified per NXP S12H family datasheet. Lead-free finish (Pb-free) confirmed by ordering suffix. RoHS and REACH compliance status not explicitly stated in Verified Web Data - set to 'unknown'. Conflict-minerals compliance assumed from NXP standard corporate policy.
