SN74HCS541PWR - Octal Buffer Schmitt 3-State TSSOP-20 | TI
部品番号: SN74HCS541PWR ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0.42 | $0.42 |
| 10 | $0.38 | $3.80 |
| 100 | $0.31 | $31.00 |
| 500 | $0.27 | $135.00 |
| 1,000 | $0.22 | $220.00 |
SN74HCS541PWR 概要
What is an octal buffer/line driver? It is a digital logic IC providing eight independent buffer channels capable of driving bus lines or long PCB traces. The 3-state outputs allow each device to release the bus into a high-impedance state, enabling multi-device bus sharing, while Schmitt-trigger inputs add hysteresis that converts slow or noisy input edges into clean logic transitions. The SN74HCS541 belongs to the HCS (High-speed CMOS with Schmitt-trigger) logic family, combining CMOS low power with TTL-compatible drive.
Key features include the 2 V to 6 V operating range for 3.3 V and 5 V mixed-voltage systems, typical 0.4 V input hysteresis at 4.5 V for superior noise immunity, dual active-low output enables (OE1 and OE2, both must be low to activate outputs), and only 20 uA typical quiescent current at 6 V. Outputs sink or source up to 6 mA at 4.5 V, suitable for driving LEDs, relays, or additional logic inputs.
Fabricated in silicon-gate CMOS, the device balances switching speed with low power dissipation. The flow-through pinout places inputs on one side and outputs on the opposite side, simplifying PCB routing and reducing crosstalk in bus-oriented layouts.
Typical applications include microcontroller bus buffering, memory address/data line driving, sensor signal conditioning, and interfacing 3.3 V logic to 5 V domains in industrial automation and automotive-adjacent systems.
Design tip: control the OE pins carefully to avoid bus contention, place 0.1 uF decoupling capacitors close to VCC/GND, and keep input rise times below 500 ns at 2 V and 200 ns at 6 V for best performance.
ドロップイン代替品: SN74HCS541PWR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: SN74HCS541PWR （同一形状・フットプリント） — 相違点: Function, Output Enable, Output Type, Packaging.
クイック比較ツール — 並列比較する代替部品を選択:
SN74HCS541QPWRQ1
✅ ドロップイン✓ 在庫あり
$0.3 / 個
データシートを見る →SN74HC541PWR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SN74HCS595PWR
⚡ 同一パッケージ ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
74HC541PW,112
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
SN74HCS541PWR 最大定格＆電気的特性
| 機能 | Octal buffer / line driver |
| Input Type | Schmitt-trigger |
| Logic Family | HCS (High-speed CMOS Schmitt) |
| チャネル数 | 8-bit per element, 1 element |
| 出力タイプ | 3-state, non-inverting |
| Supply Voltage Range | 2 V to 6 V |
| Input Hysteresis | 0.4 V typical at 4.5 V |
| Output Drive Current | 6 mA at 4.5 V (sink and source) |
| 静止電流 | 20 uA typical at 6 V |
| Output Enable | OE1 and OE2, both active-low |
| 動作温度 | -40C to +125C |
| パッケージ | 20-TSSOP (PW) |
| 実装タイプ | Surface Mount |
| Pinout Style | Flow-through |
| RoHS ステータス | Compliant |
| Packaging | Tape & Reel (PWR suffix) |
SN74HCS541PWR ピン構成
| ピン 1 | OE1 — Output enable 1 (active low) |
| ピン 2 | A1 — Data input 1 |
| ピン 3 | A2 — Data input 2 |
| ピン 4 | A3 — Data input 3 |
| ピン 5 | A4 — Data input 4 |
| ピン 6 | A5 — Data input 5 |
| ピン 7 | A6 — Data input 6 |
| ピン 8 | A7 — Data input 7 |
| ピン 9 | A8 — Data input 8 |
| ピン 10 | GND — Ground |
| ピン 11 | Y1 — Buffered output 1 (3-state) |
| ピン 12 | Y2 — Buffered output 2 (3-state) |
| ピン 13 | Y3 — Buffered output 3 (3-state) |
| ピン 14 | Y4 — Buffered output 4 (3-state) |
| ピン 15 | Y5 — Buffered output 5 (3-state) |
| ピン 16 | Y6 — Buffered output 6 (3-state) |
| ピン 17 | Y7 — Buffered output 7 (3-state) |
| ピン 18 | Y8 — Buffered output 8 (3-state) |
| ピン 19 | OE2 — Output enable 2 (active low) |
| ピン 20 | VCC — Supply voltage, 2 V to 6 V |
主な用途
SN74HCS541PWR の用途: 6 件s: Microcontroller Bus Buffering, Memory Address and Data Line Driving, Slow Signal Conditioning in Industrial Automation, 3.3 V to 5 V Logic Domain Interfacing, LED and Relay Drive Strobing, Automotive-Adjacent Control Systems.
Microcontroller Bus Buffering
The SN74HCS541PWR buffers eight address or data lines between an MCU and shared peripherals. Its 6 mA drive at 4.5 V strengthens weakened signals on long PCB traces, while the dual active-low enables let a second device share the same bus via high-impedance outputs. Schmitt-trigger inputs tolerate ringing on longer interconnects. Place 0.1 uF decoupling close to VCC and use the flow-through pinout to keep traces short and crosstalk low.
おすすめ
Memory Address and Data Line Driving
When interfacing parallel memories or external latches, the SN74HCS541PWR drives address lines from a controller with clean, fast edges. The 2 V to 6 V range supports both 3.3 V and 5 V memory systems. Outputs default to high-impedance when either OE pin is high, enabling power-up tri-state during MCU reset. Evaluate propagation delay budget at your operating voltage when adding buffers to address paths.
おすすめ
Slow Signal Conditioning in Industrial Automation
Industrial sensor outputs, RC timers, and optocoupler outputs often have rise times in the microseconds - too slow for standard CMOS inputs, which can oscillate in the threshold region. The SN74HCS541PWR's Schmitt-trigger inputs, with 0.4 V typical hysteresis at 4.5 V, snap these edges into clean logic levels while the 3-state outputs let one processor at a time read the conditioned lines. Keep rise times within the datasheet limits and decouple VCC locally.
おすすめ
3.3 V to 5 V Logic Domain Interfacing
Operating up to 6 V, the SN74HCS541PWR accepts 3.3 V logic levels from a low-voltage MCU and drives 5 V logic or loads. Its CMOS thresholds scale with VCC, and Schmitt hysteresis remains effective across the range. Typical use is translating control or data lines from a 3.3 V processor into 5 V industrial I/O or legacy TTL subsystems, using the 3-state outputs for bus sharing during handoff.
おすすめ
LED and Relay Drive Strobing
With 6 mA sink/source capability at 4.5 V per output, the SN74HCS541PWR directly drives LED indicators through resistors or small transistor drivers for relays. The eight independent channels with a common enable pair allow banked strobing: both OE pins low to enable the group, high to blank all outputs simultaneously. Schmitt inputs ensure clean strobe edges from noisy controller lines.
おすすめ
Automotive-Adjacent Control Systems
For non-safety automotive-adjacent equipment such as test fixtures and factory controllers in vehicle plants, the standard SN74HCS541PWR works to -40C to +125C. When AEC-Q100 qualification is required, the SN74HCS541QPWRQ1 drops into the same footprint with identical function. The wide 2 V to 6 V range tolerates regulated 5 V rails with headroom for transient sag, and the 20 uA quiescent current suits low-power standby nodes.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN74HCS541PWR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SN74HCS541QPWRQ1 | SN74HC541PWR | 74HC541PW,112 | MC74HC541ADWG |
|---|---|---|---|---|---|
| Package | 20-TSSOP (PW) | 20-TSSOP (PW) - same | 20-TSSOP (PW) - same | 20-TSSOP (PW) - same | SOIC-20 wide - different |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | Microchip Technology |
| Schmitt-Trigger Inputs | Yes (0.4 V typ hysteresis at 4.5 V) | Yes | No | No | No |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
| Output Drive | 6 mA at 4.5 V | 6 mA at 4.5 V | 6 mA at 4.5 V | 6 mA at 4.5 V | 6 mA at 4.5 V |
| Automotive Grade | No | Yes (AEC-Q100) | No | No | No |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +85C |
主な差別化要因
- Schmitt-trigger inputs for noisy/slow signals （vs SN74HC541PWR)
- Automotive drop-in variant available （vs SN74HCS541QPWRQ1)
- Cross-brand equivalents lack hysteresis （vs 74HC541PW,112)
設計ノート
Never enable outputs while another bus driver is active - bus contention can exceed the absolute maximum output current. Sequence OE1/OE2 so a new driver enables only after the previous driver has tri-stated. During MCU reset, hold both OE pins high (pull-ups recommended) so outputs remain high-impedance until the controller is ready.
Place a 0.1 uF ceramic decoupling capacitor within 3 mm of the VCC (pin 20) and GND (pin 10) pins, with an additional bulk 1 uF to 10 uF per board region. The flow-through pinout lets inputs and outputs route on opposite board sides - keep input and output traces separated to reduce crosstalk on parallel bus lines.
Respect the maximum recommended input transition (rise/fall) times - roughly 500 ns at 2 V and 200 ns at 6 V per the HCS family datasheet - unless using the Schmitt-trigger inputs of this HCS version. Unused inputs must not float: tie them to VCC or GND to avoid increased quiescent current and oscillation.
コンプライアンス情報
RoHS compliant per TI product page. Use SN74HCS541QPWRQ1 for AEC-Q100 qualified automotive designs.
