SN74HCS541PWR - Octal Buffer Schmitt 3-State TSSOP-20 | TI
Артикул: SN74HCS541PWR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0.42 | $0,42 |
| 10 | $0.38 | $3,80 |
| 100 | $0.31 | $31,00 |
| 500 | $0.27 | $135,00 |
| 1.000 | $0.22 | $220,00 |
SN74HCS541PWR Обзор
What is an octal buffer/line driver? It is a digital logic IC providing eight independent buffer channels capable of driving bus lines or long PCB traces. The 3-state outputs allow each device to release the bus into a high-impedance state, enabling multi-device bus sharing, while Schmitt-trigger inputs add hysteresis that converts slow or noisy input edges into clean logic transitions. The SN74HCS541 belongs to the HCS (High-speed CMOS with Schmitt-trigger) logic family, combining CMOS low power with TTL-compatible drive.
Key features include the 2 V to 6 V operating range for 3.3 V and 5 V mixed-voltage systems, typical 0.4 V input hysteresis at 4.5 V for superior noise immunity, dual active-low output enables (OE1 and OE2, both must be low to activate outputs), and only 20 uA typical quiescent current at 6 V. Outputs sink or source up to 6 mA at 4.5 V, suitable for driving LEDs, relays, or additional logic inputs.
Fabricated in silicon-gate CMOS, the device balances switching speed with low power dissipation. The flow-through pinout places inputs on one side and outputs on the opposite side, simplifying PCB routing and reducing crosstalk in bus-oriented layouts.
Typical applications include microcontroller bus buffering, memory address/data line driving, sensor signal conditioning, and interfacing 3.3 V logic to 5 V domains in industrial automation and automotive-adjacent systems.
Design tip: control the OE pins carefully to avoid bus contention, place 0.1 uF decoupling capacitors close to VCC/GND, and keep input rise times below 500 ns at 2 V and 200 ns at 6 V for best performance.
Аналоги без доработки для SN74HCS541PWR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с SN74HCS541PWR (тот же форм-фактор и посадочное место) — отличается по Function, Output Enable, Output Type, Packaging.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
SN74HCS541QPWRQ1
✅ Прямая замена✓ В наличии
$0.3 / шт.
Открыть даташит →SN74HC541PWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
SN74HCS595PWR
⚡ Тот же корпус ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
74HC541PW,112
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
SN74HCS541PWR Максимальные параметры и электрические характеристики
| Функция | Octal buffer / line driver |
| Input Type | Schmitt-trigger |
| Logic Family | HCS (High-speed CMOS Schmitt) |
| Каналы | 8-bit per element, 1 element |
| Тип выхода | 3-state, non-inverting |
| Supply Voltage Range | 2 V to 6 V |
| Input Hysteresis | 0.4 V typical at 4.5 V |
| Output Drive Current | 6 mA at 4.5 V (sink and source) |
| Ток покоя | 20 uA typical at 6 V |
| Output Enable | OE1 and OE2, both active-low |
| Рабочая температура | -40C to +125C |
| Корпус | 20-TSSOP (PW) |
| Тип монтажа | Surface Mount |
| Pinout Style | Flow-through |
| Статус RoHS | Compliant |
| Packaging | Tape & Reel (PWR suffix) |
Конфигурация выводов SN74HCS541PWR
| Контакт 1 | OE1 — Output enable 1 (active low) |
| Контакт 2 | A1 — Data input 1 |
| Контакт 3 | A2 — Data input 2 |
| Контакт 4 | A3 — Data input 3 |
| Контакт 5 | A4 — Data input 4 |
| Контакт 6 | A5 — Data input 5 |
| Контакт 7 | A6 — Data input 6 |
| Контакт 8 | A7 — Data input 7 |
| Контакт 9 | A8 — Data input 8 |
| Контакт 10 | GND — Ground |
| Контакт 11 | Y1 — Buffered output 1 (3-state) |
| Контакт 12 | Y2 — Buffered output 2 (3-state) |
| Контакт 13 | Y3 — Buffered output 3 (3-state) |
| Контакт 14 | Y4 — Buffered output 4 (3-state) |
| Контакт 15 | Y5 — Buffered output 5 (3-state) |
| Контакт 16 | Y6 — Buffered output 6 (3-state) |
| Контакт 17 | Y7 — Buffered output 7 (3-state) |
| Контакт 18 | Y8 — Buffered output 8 (3-state) |
| Контакт 19 | OE2 — Output enable 2 (active low) |
| Контакт 20 | VCC — Supply voltage, 2 V to 6 V |
Типичное применение
SN74HCS541PWR подходит для 6 применениеs: Microcontroller Bus Buffering, Memory Address and Data Line Driving, Slow Signal Conditioning in Industrial Automation, 3.3 V to 5 V Logic Domain Interfacing, LED and Relay Drive Strobing, Automotive-Adjacent Control Systems.
Microcontroller Bus Buffering
The SN74HCS541PWR buffers eight address or data lines between an MCU and shared peripherals. Its 6 mA drive at 4.5 V strengthens weakened signals on long PCB traces, while the dual active-low enables let a second device share the same bus via high-impedance outputs. Schmitt-trigger inputs tolerate ringing on longer interconnects. Place 0.1 uF decoupling close to VCC and use the flow-through pinout to keep traces short and crosstalk low.
Рекомендуется
Memory Address and Data Line Driving
When interfacing parallel memories or external latches, the SN74HCS541PWR drives address lines from a controller with clean, fast edges. The 2 V to 6 V range supports both 3.3 V and 5 V memory systems. Outputs default to high-impedance when either OE pin is high, enabling power-up tri-state during MCU reset. Evaluate propagation delay budget at your operating voltage when adding buffers to address paths.
Рекомендуется
Slow Signal Conditioning in Industrial Automation
Industrial sensor outputs, RC timers, and optocoupler outputs often have rise times in the microseconds - too slow for standard CMOS inputs, which can oscillate in the threshold region. The SN74HCS541PWR's Schmitt-trigger inputs, with 0.4 V typical hysteresis at 4.5 V, snap these edges into clean logic levels while the 3-state outputs let one processor at a time read the conditioned lines. Keep rise times within the datasheet limits and decouple VCC locally.
Рекомендуется
3.3 V to 5 V Logic Domain Interfacing
Operating up to 6 V, the SN74HCS541PWR accepts 3.3 V logic levels from a low-voltage MCU and drives 5 V logic or loads. Its CMOS thresholds scale with VCC, and Schmitt hysteresis remains effective across the range. Typical use is translating control or data lines from a 3.3 V processor into 5 V industrial I/O or legacy TTL subsystems, using the 3-state outputs for bus sharing during handoff.
Рекомендуется
LED and Relay Drive Strobing
With 6 mA sink/source capability at 4.5 V per output, the SN74HCS541PWR directly drives LED indicators through resistors or small transistor drivers for relays. The eight independent channels with a common enable pair allow banked strobing: both OE pins low to enable the group, high to blank all outputs simultaneously. Schmitt inputs ensure clean strobe edges from noisy controller lines.
Рекомендуется
Automotive-Adjacent Control Systems
For non-safety automotive-adjacent equipment such as test fixtures and factory controllers in vehicle plants, the standard SN74HCS541PWR works to -40C to +125C. When AEC-Q100 qualification is required, the SN74HCS541QPWRQ1 drops into the same footprint with identical function. The wide 2 V to 6 V range tolerates regulated 5 V rails with headroom for transient sag, and the 20 uA quiescent current suits low-power standby nodes.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для SN74HCS541PWR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SN74HCS541QPWRQ1 | SN74HC541PWR | 74HC541PW,112 | MC74HC541ADWG |
|---|---|---|---|---|---|
| Package | 20-TSSOP (PW) | 20-TSSOP (PW) - same | 20-TSSOP (PW) - same | 20-TSSOP (PW) - same | SOIC-20 wide - different |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | Microchip Technology |
| Schmitt-Trigger Inputs | Yes (0.4 V typ hysteresis at 4.5 V) | Yes | No | No | No |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
| Output Drive | 6 mA at 4.5 V | 6 mA at 4.5 V | 6 mA at 4.5 V | 6 mA at 4.5 V | 6 mA at 4.5 V |
| Automotive Grade | No | Yes (AEC-Q100) | No | No | No |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +85C |
Ключевые отличия
- Schmitt-trigger inputs for noisy/slow signals (против SN74HC541PWR)
- Automotive drop-in variant available (против SN74HCS541QPWRQ1)
- Cross-brand equivalents lack hysteresis (против 74HC541PW,112)
Заметки по проектированию
Never enable outputs while another bus driver is active - bus contention can exceed the absolute maximum output current. Sequence OE1/OE2 so a new driver enables only after the previous driver has tri-stated. During MCU reset, hold both OE pins high (pull-ups recommended) so outputs remain high-impedance until the controller is ready.
Place a 0.1 uF ceramic decoupling capacitor within 3 mm of the VCC (pin 20) and GND (pin 10) pins, with an additional bulk 1 uF to 10 uF per board region. The flow-through pinout lets inputs and outputs route on opposite board sides - keep input and output traces separated to reduce crosstalk on parallel bus lines.
Respect the maximum recommended input transition (rise/fall) times - roughly 500 ns at 2 V and 200 ns at 6 V per the HCS family datasheet - unless using the Schmitt-trigger inputs of this HCS version. Unused inputs must not float: tie them to VCC or GND to avoid increased quiescent current and oscillation.
Информация о соответствии
RoHS compliant per TI product page. Use SN74HCS541QPWRQ1 for AEC-Q100 qualified automotive designs.
