SN74LS641N - 8-Bit Open-Collector Bus Transceiver | TI
部品番号: SN74LS641N ✓ 生産中SN74LS641N 概要
A bus transceiver is a bidirectional digital interface that allows two logic buses to exchange data while controlling the direction of transmission. The SN74LS641N belongs to the broader logic IC and bus-interface hierarchy, combining eight parallel data channels, direction control, and open-collector output behavior in one integrated circuit. Open-collector outputs can support wired bus arrangements when the system includes suitable pull-up components and circuit protection.
The principal features of the SN74LS641N are its eight parallel channels, non-inverting data transfer, open-collector outputs, and separate direction control. The device transfers data from the A bus to the B bus or from the B bus to the A bus according to the DIR input state. Its 20-pin PDIP package is intended for conventional through-hole PCB assembly rather than surface-mount production.
The SN74LS641N belongs to the SN74LS family of Low-Power Schottky TTL-compatible logic devices. Open-collector output stages are the defining architectural feature, while the direction-control inputs determine which side of the transceiver drives the bus. Because the outputs are open collector, external pull-up resistors are normally required for high-level output states. Exact propagation-delay, output-voltage, input-current, and power-consumption limits should be confirmed in the manufacturer datasheet before release to production.
Typical uses include bidirectional parallel-bus interfaces, embedded data acquisition, peripheral isolation, legacy computer buses, and industrial control modules where two logic domains must exchange eight data lines. The device is especially relevant to designs that require controllable bus direction and wired-AND behavior. It can also support bus turnaround in systems where a bus driver changes between source and sink operating modes.
PCB design should provide a solid ground plane, minimize loop lengths around direction and enable controls, and place pull-up resistors close to the open-collector bus pins. The 4.75 V to 5.25 V supply range requires a stable 5 V rail. Designers should also account for the additional current drawn by pull-up resistors and verify that every connected bus node can tolerate the resulting pull-up current.
This product record combines device classification, source links, drop-in replacement analysis, package considerations, and practical interface guidance. The comparison and application sections clarify where the SN74LS641N fits within octal bus-transceiver designs and which technical details must be checked against the manufacturer datasheet.
ドロップイン代替品: SN74LS641N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
SN74ALS641A-1NSR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
SN74LS641N 最大定格&電気的特性
| Product Type | Octal bus transceiver |
| Logic Family | 74LS |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Data Direction | Bidirectional |
| Logic Polarity | Non-inverting |
| 出力タイプ | Open collector |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Output Current | 12 mA |
| パッケージ | 20-pin PDIP |
| 実装タイプ | Through-hole |
| Direction Control | DIR input |
| Output Enable | OE input |
SN74LS641N 20-pin pdip ピン配置ガイド
SN74LS641N (20-pin pdip パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: SN74LS641N.
詳細は データシート をご参照ください。
主な用途
SN74LS641N の用途: 6 件s: Bidirectional Parallel-Bus Interface, Industrial Data-Acquisition Backplane, Legacy Peripheral Data Port, Peripheral Bus Isolation and Level Translation, Printer and Instrumentation Bus, Computer and Control-System Bus Turnaround.
Bidirectional Parallel-Bus Interface
The SN74LS641N fits legacy parallel-bus links that require eight data lines to operate in either direction. Its DIR input selects A-to-B or B-to-A transfer, while the open-collector outputs support a wired-bus arrangement when external pull-up resistors are installed. The 4.75 V to 5.25 V supply range suits established 5 V equipment. Designers should allow bus turnaround time for the direction-control input and confirm that the receive and drive states cannot overlap at a given node.
おすすめ
Industrial Data-Acquisition Backplane
The SN74LS641N can connect a controller and an acquisition module over an eight-bit 5 V backplane. Bidirectional DIR control allows the controller and peripheral to exchange commands and measurements without separate bus-driver ICs, while open-collector outputs permit the bus to be pulled high through suitable resistors. The design must budget pull-up current, account for leakage from connected nodes, and verify that the backplane topology does not expose the device to excessive contention.
おすすめ
Legacy Peripheral Data Port
The SN74LS641N is appropriate for connecting a 5 V processor or controller to a legacy peripheral port containing eight bidirectional data conductors. DIR provides a simple way to reverse the bus when command and response phases alternate. Open-collector outputs can simplify shared-node signaling with suitable pull-up components, but the external network must remain within the device's voltage and current limits. Firmware should include turnaround delays appropriate to the selected bus timing.
おすすめ
Peripheral Bus Isolation and Level Translation
The SN74LS641N can isolate two 5 V logic domains through separate A-side and B-side bus connections. Direction control keeps each interface inactive during transitions, while the open-collector output architecture supports pull-up-based level adaptation when both sides use compatible logic thresholds. Isolation is functional rather than galvanic, so hazardous or high-energy nodes require separate isolation devices. Pull-up values should be derived from the target high level, total leakage, load current, and required rise time.
おすすめ
Printer and Instrumentation Bus
The SN74LS641N is useful in legacy printers, bench instruments, and other 5 V equipment that uses an eight-wire bidirectional data port. One DIR state can carry information from the host to the peripheral, and the opposite state can return status or measurements. Open-collector outputs can accommodate the bus capacitance and fault-tolerant signaling of established equipment when correctly pulled up. Integration testing should include startup contention, cable-length effects, and the peripheral's response during direction reversal.
おすすめ
Computer and Control-System Bus Turnaround
The SN74LS641N supports bidirectional bus turnaround in legacy computer and industrial-control systems by assigning the direction with DIR and disabling outputs through OE during transition intervals. The non-inverting eight-channel organization preserves data polarity and reduces external logic. Its 20-pin PDIP package supports repair and through-hole industrial boards, although the wiring must provide pull-ups and appropriate bus termination. Validate turnaround timing with the slowest connected node and the timing limits in manufacturer datasheet SN74LS641.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN74LS641N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SN74ALS641A-1NSR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 20-pin PDIP | 20-pin PDIP |
| Device Type | Octal bus transceiver | Octal bus transceiver |
| Logic Family | 74LS | ALS |
| Number of Bits | 8 bits | 8 bits |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Output Type | Open collector | Open collector |
| Data Direction | Bidirectional | Bidirectional |
主な差別化要因
- Direct bidirectional bus control (vs SN74LS244N)
- Open-collector wired-bus architecture (vs SN74LS541N)
- Pin-compatible advanced-family upgrade path (vs SN74ALS641A-1NSR)
設計ノート
The SN74LS641N requires a 4.75 V to 5.25 V supply. Because the outputs are open collector, pull-up resistors can contribute more system current than the IC itself. Estimated: if four of eight outputs are high simultaneously with a 1 kΩ pull-up to 5 V, each high output contributes approximately 5 mA, or 20 mA total, before adding device and other-load current. Confirm aggregate supply and pull-up limits in the manufacturer datasheet.
Place pull-up resistors close to the open-collector pins they serve so that transient current returns through a short loop. Keep the 20-pin PDIP footprint, supply decoupling, and ground return compatible with the original through-hole design. Provide a low-impedance ground plane and decouple the 5 V rail near the device. If the bus leaves the board, consider separate current-limiting or surge-protection components and maintain their placement close to the connector.
Do not change DIR while two connected nodes are actively driving the same bus. Use OE to disable outputs during turnaround and allow the required settling interval before changing direction. Open-collector stages do not actively source a high level, so omitting pull-up resistors or selecting values that are too high can produce slow rising edges and unreliable communication. Verify polarity, DIR truth table, and bus timing against manufacturer datasheet SN74LS641.
Open-collector rise time is governed by the pull-up resistance and total bus capacitance, not only by the transceiver. Estimated: with a 1 kΩ pull-up and 100 pF of total bus capacitance, the RC time constant is approximately 100 ns. Use this relationship as an initial assessment and compare the resulting edge rate with the receiving system's setup and hold requirements. Reduce pull-up resistance only after checking output-current, voltage-drop, and power limits.
コンプライアンス情報
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer and distributor product information used for this record.