Texas Instruments

SN74LS641N - 8-Bit Open-Collector Bus Transceiver | TI

MPN: SN74LS641N ✓ פעיל
4.75 V to 5.25 V Vdss 12 mA Id 20-pin PDIP Package
כמות הזמנה מינימלית: 1 |

SN74LS641N סקירה

The Texas Instruments SN74LS641N is an 8-bit octal bus transceiver with open-collector outputs, supplied in a 20-pin PDIP package. It is designed for 5 V systems and supports bidirectional transfer between A and B data buses through direction-control and output-enable inputs. The operating voltage shown for this device is 4.75 V to 5.25 V, with an output-current capability listed as 12 mA.

A bus transceiver is a bidirectional digital interface that allows two logic buses to exchange data while controlling the direction of transmission. The SN74LS641N belongs to the broader logic IC and bus-interface hierarchy, combining eight parallel data channels, direction control, and open-collector output behavior in one integrated circuit. Open-collector outputs can support wired bus arrangements when the system includes suitable pull-up components and circuit protection.

The principal features of the SN74LS641N are its eight parallel channels, non-inverting data transfer, open-collector outputs, and separate direction control. The device transfers data from the A bus to the B bus or from the B bus to the A bus according to the DIR input state. Its 20-pin PDIP package is intended for conventional through-hole PCB assembly rather than surface-mount production.

The SN74LS641N belongs to the SN74LS family of Low-Power Schottky TTL-compatible logic devices. Open-collector output stages are the defining architectural feature, while the direction-control inputs determine which side of the transceiver drives the bus. Because the outputs are open collector, external pull-up resistors are normally required for high-level output states. Exact propagation-delay, output-voltage, input-current, and power-consumption limits should be confirmed in the manufacturer datasheet before release to production.

Typical uses include bidirectional parallel-bus interfaces, embedded data acquisition, peripheral isolation, legacy computer buses, and industrial control modules where two logic domains must exchange eight data lines. The device is especially relevant to designs that require controllable bus direction and wired-AND behavior. It can also support bus turnaround in systems where a bus driver changes between source and sink operating modes.

PCB design should provide a solid ground plane, minimize loop lengths around direction and enable controls, and place pull-up resistors close to the open-collector bus pins. The 4.75 V to 5.25 V supply range requires a stable 5 V rail. Designers should also account for the additional current drawn by pull-up resistors and verify that every connected bus node can tolerate the resulting pull-up current.

This product record combines device classification, source links, drop-in replacement analysis, package considerations, and practical interface guidance. The comparison and application sections clarify where the SN74LS641N fits within octal bus-transceiver designs and which technical details must be checked against the manufacturer datasheet.

חלופות תחליף ישיר עבור SN74LS641N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

SN74ALS641A-1NSR

✅ Drop-In
📦 20-pin PDIP
Advanced LS-family timing replaces the original 74LS timing while retaining the 20-pin PDIP footprint, 4.75 V to 5.25 V supply range, and 8-bit open-collector transceiver function; exact propagation-delay difference is

📋 חלופה להתייחסות (לא בקטלוג)

SN74LS641N דירוגים מרביים ומאפיינים חשמליים

Product Type Octal bus transceiver
Logic Family 74LS
Number of Elements 1 element
Bits per Element 8 bits
Data Direction Bidirectional
Logic Polarity Non-inverting
סוג פלט Open collector
Supply Voltage Range 4.75 V to 5.25 V
Output Current 12 mA
מארז 20-pin PDIP
סוג הרכבה Through-hole
Direction Control DIR input
Output Enable OE input

מדריך תצורת פינים של SN74LS641N 20-pin pdip

תצורת פינים עבור SN74LS641N (מארזת 20-pin pdip). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.

תרשים פינים של מארזת 20-pin pdip עבור SN74LS641N

אין נתוני פריסת פינים מפורטים עבור SN74LS641N.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

SN74LS641N מתאים עבור 6 יישוםs: Bidirectional Parallel-Bus Interface, Industrial Data-Acquisition Backplane, Legacy Peripheral Data Port, Peripheral Bus Isolation and Level Translation, Printer and Instrumentation Bus, Computer and Control-System Bus Turnaround.

🖥️

Bidirectional Parallel-Bus Interface

The SN74LS641N fits legacy parallel-bus links that require eight data lines to operate in either direction. Its DIR input selects A-to-B or B-to-A transfer, while the open-collector outputs support a wired-bus arrangement when external pull-up resistors are installed. The 4.75 V to 5.25 V supply range suits established 5 V equipment. Designers should allow bus turnaround time for the direction-control input and confirm that the receive and drive states cannot overlap at a given node.

🏭

Industrial Data-Acquisition Backplane

The SN74LS641N can connect a controller and an acquisition module over an eight-bit 5 V backplane. Bidirectional DIR control allows the controller and peripheral to exchange commands and measurements without separate bus-driver ICs, while open-collector outputs permit the bus to be pulled high through suitable resistors. The design must budget pull-up current, account for leakage from connected nodes, and verify that the backplane topology does not expose the device to excessive contention.

🔧

Legacy Peripheral Data Port

The SN74LS641N is appropriate for connecting a 5 V processor or controller to a legacy peripheral port containing eight bidirectional data conductors. DIR provides a simple way to reverse the bus when command and response phases alternate. Open-collector outputs can simplify shared-node signaling with suitable pull-up components, but the external network must remain within the device's voltage and current limits. Firmware should include turnaround delays appropriate to the selected bus timing.

🔧

Peripheral Bus Isolation and Level Translation

The SN74LS641N can isolate two 5 V logic domains through separate A-side and B-side bus connections. Direction control keeps each interface inactive during transitions, while the open-collector output architecture supports pull-up-based level adaptation when both sides use compatible logic thresholds. Isolation is functional rather than galvanic, so hazardous or high-energy nodes require separate isolation devices. Pull-up values should be derived from the target high level, total leakage, load current, and required rise time.

🖥️

Printer and Instrumentation Bus

The SN74LS641N is useful in legacy printers, bench instruments, and other 5 V equipment that uses an eight-wire bidirectional data port. One DIR state can carry information from the host to the peripheral, and the opposite state can return status or measurements. Open-collector outputs can accommodate the bus capacitance and fault-tolerant signaling of established equipment when correctly pulled up. Integration testing should include startup contention, cable-length effects, and the peripheral's response during direction reversal.

💻

Computer and Control-System Bus Turnaround

The SN74LS641N supports bidirectional bus turnaround in legacy computer and industrial-control systems by assigning the direction with DIR and disabling outputs through OE during transition intervals. The non-inverting eight-channel organization preserves data polarity and reduces external logic. Its 20-pin PDIP package supports repair and through-hole industrial boards, although the wiring must provide pull-ups and appropriate bus termination. Validate turnaround timing with the slowest connected node and the timing limits in manufacturer datasheet SN74LS641.

What is the SN74LS641N?
The SN74LS641N is an 8-bit octal bidirectional bus transceiver with open-collector outputs from Texas Instruments. It is packaged in a 20-pin PDIP and operates from 4.75 V to 5.25 V. According to the manufacturer datasheet SN74LS641, data transfers from the A bus to the B bus or from B to A depending on the DIR control input, making the device suitable for controlled two-way parallel-bus communication.
Where can I download the SN74LS641N datasheet PDF?
The official SN74LS641 datasheet is available through the Texas Instruments product page at https://www.ti.com/lit/gpn/SN74LS641. The document is identified as SDLS189 and covers the SN54LS640 through SN74LS642, SN74LS644, and SN74LS645 octal bus-transceiver family. Use the manufacturer copy for final pin assignments, timing limits, electrical characteristics, and recommended operating conditions.
What is the SN74LS641N pinout?
The SN74LS641N uses a 20-pin PDIP configuration with separate data, direction-control, and output-enable functions. Exact numbering for the A-side, B-side, DIR, OE, VCC, and GND connections should be taken directly from the pin-description table in the manufacturer datasheet SN74LS641. Use that table when assigning PCB nets, especially when preserving an existing through-hole bus-interface footprint.
What voltage does the SN74LS641N operate at?
The SN74LS641N operates from 4.75 V to 5.25 V. This range is stated in the product listing and corresponds to a nominal 5 V Low-Power Schottky TTL logic supply. According to the manufacturer datasheet SN74LS641, the design belongs to the SN74LS octal bus-transceiver family. The system should maintain the supply within the specified limits across temperature and load conditions.
How does the DIR input on the SN74LS641N work?
The DIR input selects the direction in which the SN74LS641N transfers data between its A and B buses. The device can transmit from A to B or from B to A while its open-collector output stages remain under logic control. According to the manufacturer datasheet SN74LS641, DIR works with the output-enable function to prevent unwanted bus contention during direction changes.
Does the SN74LS641N need pull-up resistors?
Yes, open-collector outputs normally require external pull-up resistors to establish a high output level. The resistor value must be selected from the bus voltage, the number of simultaneously high outputs, total leakage current, and the required rise time. According to the manufacturer datasheet SN74LS641, the open-collector architecture supports wired bus operation when the system supplies suitable pull-up and fault-protection components.
What is the best drop-in replacement for the SN74LS641N?
SN74ALS641A-1NSR is the most directly supported drop-in candidate because it is described as having consistent terminals, package, and principal performance characteristics. It uses a 20-pin PDIP and retains the octal open-collector transceiver function, so it can replace the SN74LS641N without PCB changes. The advanced LS-family timing and electrical limits should still be reviewed against the original system requirements.
Can SN74ALS641A-1NSR replace SN74LS641N?
SN74ALS641A-1NSR can serve as a pin-compatible replacement for the SN74LS641N in an unmodified 20-pin PDIP design. The replacement comparison identifies matching terminals, package, and functional characteristics. It is an advanced Low-Power Schottky variant, so engineers should verify propagation delay, supply voltage, output-current, and open-collector behavior against the original design before production release.
SN74LS641N vs SN74LS642N: which transceiver should be selected?
Choose the SN74LS641N when non-inverting bidirectional data transfer is required, and evaluate SN74LS642N when the bus interface needs inverting transfer behavior. Both devices are listed in the manufacturer family documentation as octal open-collector bus transceivers, but their data polarity differs. Confirm the complete pin and logic-function tables in manufacturer datasheet SN74LS641 before treating either part as a substitute.
SN74LS641N vs SN74LS244N: which is the better fit?
Choose the SN74LS641N for bidirectional bus communication controlled by DIR, and choose the SN74LS244N for a non-directional octal buffer arrangement. The SN74LS641N has open-collector outputs and two bidirectional bus sides, while the SN74LS244N belongs to a different buffer/drive function. The distinction determines whether the design requires explicit direction control or only fixed data flow.
When should I choose the SN74LS641N instead of a modern logic transceiver?
Choose the SN74LS641N when maintaining a legacy 5 V bus interface is more important than adopting newer low-power or higher-speed logic. Its 4.75 V to 5.25 V operating range, 8-bit bidirectional channels, direction control, and open-collector outputs support established wired-bus designs. Select a modern transceiver when lower supply voltage, faster edge rates, shorter propagation delay, or a smaller surface-mount package is required.
Is the SN74LS641N suitable for industrial control and data acquisition?
The SN74LS641N is suitable for legacy industrial-control and data-acquisition interfaces that use a 5 V parallel bus and need controlled bidirectional transfer. Its 8-bit channel count and DIR control support peripheral bus turnaround, while open-collector outputs can accommodate wired-bus signaling with pull-up resistors. Industrial qualification, temperature range, isolation, and transient protection must be checked separately for the deployed environment.
What is the lead time for SN74LS641N?
The current lead time for SN74LS641N should be requested through the Request a Quote form on this page. Stock and manufacturing schedule can change, so engineers should confirm the quantity, date code, package, and delivery requirements with the supplier before committing a production schedule. The device is offered in a 20-pin PDIP package, and lead time should be confirmed for that exact ordering configuration.
Is SN74LS641N in stock?
Current SN74LS641N inventory should be checked through the Request a Quote form on this page. The part is a 20-pin PDIP octal bus transceiver with open-collector outputs, and the required quantity and package designation should be stated in the request. Avoid treating distributor search listings as a guaranteed stock commitment without receiving a confirmed quote and allocation.
Where should I buy SN74LS641N online?
Use the Request a Quote form on this page to request SN74LS641N availability, commercial terms, and delivery information. The form is the appropriate route for checking the exact 20-pin PDIP configuration and current production allocation. For engineering validation, obtain the official manufacturer datasheet and confirm the device, pinout, supply range, and open-collector requirements before placing an order.

נתוני עזר הנדסיים עבור SN74LS641N — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the SN74LS641N for a legacy 5 V system that needs an eight-bit bidirectional parallel bus with DIR-controlled direction and open-collector outputs. It is particularly appropriate when the existing PCB uses a 20-pin PDIP footprint and the bus architecture benefits from external pull-up resistors or wired-bus behavior. Choose SN74ALS641A-1NSR when the same package and function are required but newer ALS-family timing is desirable; verify timing and electrical limits before substitution. Consider SN74LS642N only when inverting data polarity is desired, and use SN74LS244N for fixed-direction buffering rather than two-way bus control. For new compact or low-power systems, modern surface-mount transceivers may offer better size, speed, and supply-voltage flexibility, but they are not assumed to be drop-in replacements.

השוואה עם חלופות

פרמטר מוצר זה SN74ALS641A-1NSR
Brand Texas Instruments Texas Instruments
Package 20-pin PDIP 20-pin PDIP
Device Type Octal bus transceiver Octal bus transceiver
Logic Family 74LS ALS
Number of Bits 8 bits 8 bits
Supply Voltage Range 4.75 V to 5.25 V 4.75 V to 5.25 V
Output Type Open collector Open collector
Data Direction Bidirectional Bidirectional

מבדילים עיקריים

  • Direct bidirectional bus control (לעומתSN74LS244N)
  • Open-collector wired-bus architecture (לעומתSN74LS541N)
  • Pin-compatible advanced-family upgrade path (לעומתSN74ALS641A-1NSR)

הערות תכנון

The SN74LS641N requires a 4.75 V to 5.25 V supply. Because the outputs are open collector, pull-up resistors can contribute more system current than the IC itself. Estimated: if four of eight outputs are high simultaneously with a 1 kΩ pull-up to 5 V, each high output contributes approximately 5 mA, or 20 mA total, before adding device and other-load current. Confirm aggregate supply and pull-up limits in the manufacturer datasheet.

Place pull-up resistors close to the open-collector pins they serve so that transient current returns through a short loop. Keep the 20-pin PDIP footprint, supply decoupling, and ground return compatible with the original through-hole design. Provide a low-impedance ground plane and decouple the 5 V rail near the device. If the bus leaves the board, consider separate current-limiting or surge-protection components and maintain their placement close to the connector.

Do not change DIR while two connected nodes are actively driving the same bus. Use OE to disable outputs during turnaround and allow the required settling interval before changing direction. Open-collector stages do not actively source a high level, so omitting pull-up resistors or selecting values that are too high can produce slow rising edges and unreliable communication. Verify polarity, DIR truth table, and bus timing against manufacturer datasheet SN74LS641.

Open-collector rise time is governed by the pull-up resistance and total bus capacitance, not only by the transceiver. Estimated: with a 1 kΩ pull-up and 100 pF of total bus capacitance, the RC time constant is approximately 100 ns. Use this relationship as an initial assessment and compare the resulting edge rate with the receiving system's setup and hold requirements. Reduce pull-up resistance only after checking output-current, voltage-drop, and power limits.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer and distributor product information used for this record.

חיפושים קשורים

SN74LS641N datasheet SN74LS641N pinout SN74LS641N datasheet pdf Texas Instruments SN74LS641N SN74LS641N equivalent SN74LS641N replacement SN74LS641N cross reference SN74LS641N price SN74LS641N stock SN74LS641N vs SN74LS642N SN74LS641N vs SN74LS244N SN74LS641N 20-pin PDIP SN74LS641N open collector output SN74LS641N bidirectional bus

רכיבים ומונחים קשורים

Texas Instruments SN74LS641N SN74LS641 SN74ALS641A-1NSR SN74LS642N SN74LS244N SN74LS541N Octal bus transceiver Logic IC Bidirectional transceiver Open-collector output 74LS logic family ALS logic family DIR control input Output enable Parallel bus Wired bus Pull-up resistor 20-pin PDIP Through-hole package 4.75 V minimum supply 5.25 V maximum supply 12 mA output current Non-inverting logic
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר