SST-PFB3-PCI - Profibus DP PCI Interface Card | Molex Woodhead
部品番号: SST-PFB3-PCI ⚠ ラストタイムバイ| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1850 | $1,850.00 |
| 5 | $1780 | $8,900.00 |
| 10 | $1720 | $17,200.00 |
| 25 | $1650 | $41,250.00 |
| 50 | $1595 | $79,750.00 |
SST-PFB3-PCI 概要
A PROFIBUS interface card is a dedicated hardware adapter that lets a Windows or Linux industrial PC, PLC backplane, or SCADA server exchange real-time I/O data with field devices such as remote I/O blocks, variable-frequency drives, encoders, and valve manifolds over the PROFIBUS DP (Decentralized Periphery) fieldbus. PROFIBUS DP is an IEC 61158 / EN 50170 standard fieldbus widely deployed in factory automation, process control, and motion-control applications. Within an automation hierarchy, a PROFIBUS card sits between the controller layer (PLC/industrial PC) and the device/field layer, providing deterministic cyclic I/O and acyclic parameterization channels. The SST-PFB3-PCI acts as the controller-side endpoint for those networks.
Key features include support for PROFIBUS DP-V0, DP-V1, and FDL messaging, Master Class 1 and Class 2 capability, automatic 5 V / 3.3 V PCI signaling-level detection for universal motherboard compatibility, and downloadable application firmware modules that enable product-level behavior. An onboard processor manages the protocol stack, freeing the host CPU for application logic. The card is backward-compatible where possible with the legacy SST 5136-PFB-PCI, although it is not a drop-in replacement for that older board.
The SST-PFB3-PCI is most often deployed in industrial PCs that act as PROFIBUS masters communicating with distributed I/O such as Siemens ET200, ABB drives, or third-party valve terminals. It is used in SCADA and HMI hosts that need to poll remote I/O racks, in PLC programming stations that must download project data to PROFIBUS-coupled controllers, and in test rigs and laboratory automation racks that exchange deterministic I/O with PROFIBUS-coupled instrumentation. The onboard CPU offload makes it suitable where deterministic latency is required regardless of host load.
When integrating the SST-PFB3-PCI, verify that the host motherboard is fully PCI 2.2 (or later) compliant, because the optional 3.3 V supply in PCI 2.1 may not power the card on some legacy boards. Use a shielded PROFIBUS DP cable with a 9-pin D-sub connector, and terminate the segment with the standard PROFIBUS terminator at both ends. Configure the baud rate (9.6 kbps to 12 Mbps) to match the slowest device on the segment, and update the card firmware via the SST configuration tool before commissioning.
ドロップイン代替品: SST-PFB3-PCI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
SST-PB3-PCU
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SST-PB3-PCI-e
✅ ドロップイン📋 参考代替品（カタログ未掲載）
5136-PFB-ISA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
5136-PFB-PCI
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ProSoft PTQ-PDPMV1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SST-PFB3-PCI 仕様（メーカー公開）
| Product Type | PROFIBUS DP PCI Interface Card |
| Manufacturer | Molex Woodhead (formerly SST) |
| Host Bus | PCI 2.2 (universal, 5 V / 3.3 V signaling) |
| Supported Protocols | PROFIBUS DP-V0, DP-V1, FDL (Layer 2) |
| Operating Modes | DP Master Class 1, DP Master Class 2, DP Slave, FDL messaging |
| Baud Rate | 9.6 kbps to 12 Mbps (auto-detect) |
| Onboard CPU | Yes (offloads protocol stack from host CPU) |
| Downloadable Firmware | Supported (application firmware modules) |
| Form Factor | Half-height PCI card |
| Card Dimensions | 175 x 107 mm |
| Weight | 0.46 kg |
| Field Connector | PROFIBUS 9-pin D-sub |
| Origin | USA |
| Compliance / Standard | IEC 61158 / EN 50170 (PROFIBUS) |
| Backward Compatibility | Maintained with legacy SST 5136-PFB-PCI (where possible); not a drop-in replacement |
SST-PFB3-PCI インターフェースとコネクタ
SST-PFB3-PCI について、メーカーが公開しているインターフェース一覧はありません。コネクタとヘッダーの詳細については、メーカーのドキュメントを参照してください。
詳細は メーカー資料 をご参照ください（拡張ヘッダーのピン配置とコネクタのピン番号の詳細）。
主な用途
SST-PFB3-PCI の用途: 6 件s: Industrial PC PROFIBUS-DP Master, SCADA / HMI Host PROFIBUS Connectivity, PLC Programming and Commissioning Station, Process Control and DCS Test Rigs, Drive and Motion Control Integration, Legacy System Maintenance and Migration.
Industrial PC PROFIBUS-DP Master
The SST-PFB3-PCI lets a PCI-bus industrial PC act as a PROFIBUS-DP Master Class 1 or Class 2, polling remote I/O such as Siemens ET200, ABB ACS drives, and Festo valve manifolds. Its 12 Mbps auto-baud rate, DP-V0/V1/FDL support, and onboard protocol-stack CPU make it ideal where deterministic cyclic I/O is required regardless of host OS load. Engineers deploy it when SCADA or soft-PLC software (e.g. WinCC, iFIX, Codesys) must exchange real-time I/O with field devices that speak PROFIBUS DP.
おすすめ
SCADA / HMI Host PROFIBUS Connectivity
SCADA and HMI servers running on industrial PCs use the SST-PFB3-PCI to poll PROFIBUS-coupled remote I/O racks and instrumentation. The card's onboard CPU offload ensures that cyclic I/O remains jitter-free even when the host runs antivirus scans, database updates, or operator-screen refreshes. Typical deployments pair the SST-PFB3-PCI with Wonderware, iFIX, or Citect SCADA software, where deterministic PROFIBUS DP-V1 acyclic parameter reads are used for device diagnostics.
おすすめ
PLC Programming and Commissioning Station
Engineering workstations use the SST-PFB3-PCI to download project data to PROFIBUS-coupled PLCs and to upload diagnostic traces during commissioning. With DP-Master Class 2 support, the card can perform online program changes, online monitoring, and force-table operations on PROFIBUS-coupled controllers without disturbing production traffic. The downloadable firmware modules allow the same card to be repurposed across multiple PLC brands on a project.
おすすめ
Process Control and DCS Test Rigs
Distributed control system (DCS) test rigs and laboratory automation racks use the SST-PFB3-PCI as a deterministic PROFIBUS-DP endpoint that exchanges I/O with PROFIBUS-coupled transmitters, valve positioners, and analytical instruments. The card's FDL (Layer 2) messaging capability enables raw frame inspection for protocol conformance testing, while DP-V1 acyclic services support device-parameter downloads typical of process-control commissioning.
おすすめ
Drive and Motion Control Integration
PROFIBUS-DP is widely used to set parameters and stream control words to variable-frequency drives, servo amplifiers, and stepper drives. The SST-PFB3-PCI in a motion host PC can poll drive status, write speed setpoints, and synchronize multi-axis motion profiles over PROFIBUS DP-V1 acyclic channels. Its onboard CPU guarantees deterministic cyclic update of drive control words even when the host renders 3D motion-preview visualizations.
おすすめ
Legacy System Maintenance and Migration
Many factories still operate PCI-bus industrial PCs that drive long-life production lines, and the SST-PFB3-PCI is the supported PROFIBUS endpoint for these systems. When original equipment is obsolete, distributors such as Artisan Technology Group, DCS Module, and NewPLC supply post-EOL stock with warranty support, enabling maintenance teams to keep legacy lines running while planning longer-term migration to PCIe or Ethernet-based fieldbus architectures.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SST-PFB3-PCI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SST-PB3-PCU | SST-PB3-PCI-e | 5136-PFB-ISA | 5136-PFB-PCI | ProSoft PTQ-PDPMV1 |
|---|---|---|---|---|---|---|
| Brand | Molex (Woodhead / SST) | Molex (Woodhead / SST) | Molex (Woodhead / SST) | Molex (Woodhead / SST) | Molex (Woodhead / SST) | ProSoft Technology |
| Package | PCI card (175 x 107 mm) | PCI card (PCU variant) | PCIe card | ISA card | PCI card (legacy) | PCI / modular PROFIBUS master |
| PROFIBUS Protocols Supported | DP-V0, DP-V1, FDL | DP-V0, DP-V1, FDL | DP-V0, DP-V1, FDL | DP-V0, FDL | DP-V0, DP-V1, FDL | DP-V0, DP-V1 |
| Master Class Support | Class 1 + Class 2 | Class 1 + Class 2 | Class 1 + Class 2 | Class 1 + Class 2 | Class 1 + Class 2 | Class 1 + Class 2 |
| DP Slave Support | Yes | Yes | Yes | Yes | Yes | Yes |
| Max Baud Rate | 12 Mbps | 12 Mbps | 12 Mbps | 12 Mbps | 12 Mbps | 12 Mbps |
| Onboard Protocol CPU | Yes | Yes | Yes | Yes | Yes | Yes |
| PCI Signaling Level | 5 V / 3.3 V auto-detect (PCI 2.2) | 5 V / 3.3 V auto-detect (PCI) | PCIe (not PCI signaling) | ISA bus (not PCI signaling) | PCI 5 V (legacy) | PCI / modular |
主な差別化要因
- Third-generation PFB3 architecture with auto-detected 5 V / 3.3 V PCI signaling （vs SST-PB3-PCU)
- Downloadable application firmware modules for product-level behavior （vs ProSoft PTQ-PDPMV1)
- Backward compatibility where possible with legacy 5136-PFB-PCI and 5136-PFB-ISA （vs SST-PB3-PCI-e)
設計ノート
The SST-PFB3-PCI draws power from the PCI host bus (5 V and optionally 3.3 V). On PCI revision 2.1 motherboards where the 3.3 V rail is optional, the card may not enumerate or may behave unpredictably. Confirm full PCI 2.2 (or later) compliance of the host motherboard before deployment, or migrate to the SST-PB3-PCI-e PCIe variant on newer systems that no longer expose PCI slots.
Use shielded PROFIBUS DP cable with a 9-pin D-sub connector (DB9) terminated at both ends with the standard PROFIBUS terminator (390 ohm between data+ and 5 V, 220 ohm between data- and GND on each end). Maintain a minimum 1 m stub length to the nearest device, and route the PROFIBUS cable at least 20 cm away from VFD power cables to minimize EMI coupling.
The SST-PFB3-PCI is NOT a drop-in replacement for the legacy SST 5136-PFB-PCI - Molex explicitly states backward compatibility is maintained only where possible. When migrating from a 5136-PFB-PCI to a SST-PFB3-PCI, plan for firmware reflash, GSD-file updates, and configuration migration. Do not assume same-slot hot-swap compatibility; the firmware boot sequence differs.
Auto-detect baud rate from 9.6 kbps to 12 Mbps, but the actual segment baud rate is locked to the slowest device during configuration. For long cable runs near 12 Mbps, verify signal integrity with a PROFIBUS cable tester and use only IEC 61158 Type-A PROFIBUS cable (characteristic impedance 150 ohm). Degraded cables may pass at 1.5 Mbps but fail at 12 Mbps under EMC events.
コンプライアンス情報
Publicly available SST-PFB3-PCI datasheets and distributor listings do not explicitly state current RoHS / REACH / lead-free status. The card is industrial PROFIBUS equipment, not automotive-grade, so AEC-Q100 is not applicable. Confirm compliance with the chosen distributor at order time for new EU installations.
関連検索
関連部品&用語
おすすめを読み込み中...