STM32F103T6U6 - 72MHz Cortex-M3 32KB MCU | STMicroelectronics
部品番号: STM32F103T6U6 ✓ 生産中STM32F103T6U6 概要
A microcontroller, or MCU, integrates a processor core, program memory, volatile data memory, and peripherals such as timers, serial interfaces, analog converters, and GPIO into one package. Within the semiconductor hierarchy, the STM32F103T6U6 is an embedded microcontroller, a Cortex-M processor-based system-on-chip, and a member of the broader power management and industrial-control component category. Its integrated design reduces external component count while providing deterministic control for motor, communications, and instrumentation applications.
The verified device data identifies an ARM Cortex-M3 core with a maximum operating frequency of 72 MHz, 32 KB of Flash, 10 KB of SRAM, and six timers. Two 12-bit ADCs are included for analog measurement, while USB and CAN interfaces support direct connectivity and industrial network communication. The listed 2 V to 3.6 V supply range supports conventional embedded systems operating from regulated 2.5 V or 3.3 V rails.
The STM32F103T6U6 is positioned as a low-density performance-line MCU rather than a high-pin-count Cortex-M4 device. This makes it appropriate for designs that need more control capability than a basic 8-bit or low-performance 32-bit MCU without paying for the memory and peripheral resources of a larger controller. Its six timers can support timing, PWM, input capture, encoder, and motor-control functions, while the communication interfaces reduce the need for separate protocol devices.
Typical uses include USB-connected data acquisition, CAN-connected industrial controllers, compact motor-control boards, and low-cost embedded instruments. For CAN equipment, the controller is placed on the same board as a CAN transceiver; for USB equipment, it connects to a USB transceiver through the MCU’s internal USB controller. The ADC channels can monitor sensors, potentiometers, or analog process inputs where 12-bit resolution and conversion throughput are sufficient.
PCB design should preserve clean supply distribution, ground continuity, analog-input routing, and exposed-pad or thermal-pad handling appropriate to the exact LQFP-48 land pattern. Firmware should also account for the difference between a 72 MHz maximum clock and lower operating frequencies during initialization, power management, and peripheral timing. This page consolidates verified source data, substitution limits, and engineering guidance rather than presenting unverified substitute parts as unconditional drop-ins.
ドロップイン代替品: STM32F103T6U6 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: STM32F103T6U6 （同一形状・フットプリント） — 相違点: Flash Memory, Package, Product Type.
GD32F103T6U6
✅ ドロップイン📋 参考代替品（カタログ未掲載）
STM32F103T6U6 最大定格＆電気的特性
| Product Type | Low-density performance-line 32-bit microcontroller |
| CPU Core | ARM Cortex-M3 32-bit RISC core |
| Maximum CPU Frequency | 72 MHz |
| Flash Memory | 32 KB |
| SRAM | 10 KB |
| Supply Voltage Range | 2 V to 3.6 V |
| Number of ADCs | 2 |
| Number of Timers | 6 |
| Number of Communication Interfaces | 6 |
| I/O Ports | 37 |
| USB Interface | Yes |
| CAN Interface | Yes |
| パッケージ | LQFP-48, 7 x 7 mm |
| 実装タイプ | Surface Mount |
| RoHS ステータス | RoHS compliant |
| Lifecycle Stage | Active |
STM32F103T6U6 lqfp-48, 7 x 7 mm ピン配置ガイド
STM32F103T6U6 (lqfp-48, 7 x 7 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: STM32F103T6U6.
詳細は データシート をご参照ください。
主な用途
STM32F103T6U6 の用途: 6 件s: USB Data-Acquisition Controller, CAN-Connected Industrial Controller, Compact Motor-Control System, Industrial Sensor Hub, Communication Gateway, Low-Cost Embedded Instrument.
USB Data-Acquisition Controller
The STM32F103T6U6 fits USB-connected acquisition equipment because its Cortex-M3 core runs up to 72 MHz and its verified feature set includes USB, two ADCs, six timers, 32 KB Flash, and 10 KB SRAM. The MCU can sample analog inputs, format results, and transfer data through the USB controller while an external transceiver handles the physical USB connection. The two ADCs are valuable for sensor, potentiometer, and process-input conditioning, while timers can establish deterministic sampling and communication timing. Because the USB controller is embedded, software must handle enumeration and endpoint behavior without relying on a separate protocol microcontroller. A practical design should include controlled USB routing, solid ground return, local 3.3 V decoupling, and analog input filtering. The GD32F103T6U6 is a documented second source, but its 108 MHz maximum clock and different Flash timing and ADC behavior require regression testing before substitution.
おすすめ
CAN-Connected Industrial Controller
The STM32F103T6U6 is appropriate for a compact CAN-connected industrial controller because the verified specifications identify CAN support, six timers, six communication interfaces, 37 I/O ports, and a 72 MHz Cortex-M3 core. It can execute control logic, handle CAN frames, operate timers, and supervise digital I/O in a single component. A separate CAN transceiver is still required to convert the MCU’s digital controller signals to the physical bus, and the board must account for bus protection, termination, isolation requirements, and common-mode noise. The six timers allow periodic tasks and communication timing to remain deterministic, while the 2 V to 3.6 V operating range supports regulated embedded rails. The GD32F103T6U6 offers a pin-compatible sourcing option, but engineers should validate interrupt behavior, peripheral differences, Flash wait states, and ADC performance on production hardware.
おすすめ
Compact Motor-Control System
The STM32F103T6U6 supports compact motor-control systems through its 72 MHz ARM Cortex-M3 core, six timers, two ADCs, 37 I/O ports, and 10 KB SRAM. Timer channels can generate PWM and capture timing signals, while the ADC channels can monitor current, position, or analog feedback. The device consolidates these functions into an LQFP-48 package, reducing the need for separate timing and analog-conversion components. For motor drives, the MCU is normally used with external power-stage transistors, gate drivers, current sensing, and protection circuitry; it does not directly drive a motor. Firmware should include controlled startup, fault handling, and appropriate dead-time behavior. The GD32F103T6U6 may preserve the board outline, but its 108 MHz clock ceiling and reported ADC differences require timing and current-measurement validation.
おすすめ
Industrial Sensor Hub
The STM32F103T6U6 is well matched to an industrial sensor hub that must combine analog measurement, digital input monitoring, and network communication. Its two ADCs support multiple analog channels, 37 I/O ports provide sensor and alarm inputs, and the six timers can handle periodic sampling, timeout management, and output updates. At 72 MHz, the Cortex-M3 core provides deterministic execution for sensor filtering, calibration, threshold logic, and communication tasks without requiring a separate processor. A robust implementation should electrically isolate long field wiring, condition sensor inputs, use regulated 3.3 V power, and keep analog routing away from switching nodes. Firmware must also provide watchdog recovery and safe-state outputs. The GD32F103T6U6 can serve as a pin-compatible sourcing candidate, but production adoption should follow ADC, Flash-timing, and peripheral regression tests.
おすすめ
Communication Gateway
The STM32F103T6U6 can serve as the control processor in a communication gateway because it combines USB, CAN, six communication interfaces, six timers, 32 KB Flash, and 10 KB SRAM in one device. This permits protocol handling, local configuration, status reporting, and data buffering on a common controller rather than requiring several devices for basic gateway functions. The design still needs appropriate transceivers and protection for each physical interface, along with controlled clocking and robust firmware update mechanisms for deployed equipment. The 2 V to 3.6 V operating range supports conventional embedded rails, while 37 I/O ports can support status indicators, configuration switches, and supervisory signals. For a second source, GD32F103T6U6 preserves the pin arrangement but requires library, timing, ADC, and peripheral regression testing before production release.
おすすめ
Low-Cost Embedded Instrument
The STM32F103T6U6 is suitable for a low-cost embedded instrument that combines measurement, display control, communications, and user input. Its 72 MHz Cortex-M3 core can run sampling and signal-processing routines, while two ADCs handle analog inputs and six timers provide precise interval generation. The 37 I/O ports can support display strobes, buttons, indicators, and digital sensors, and the integrated USB capability enables PC connectivity when paired with a transceiver. Because only 32 KB of Flash and 10 KB of SRAM are available, firmware designers should avoid unnecessary libraries, graphics assets, and large diagnostic buffers. Decoupling, analog grounding, and careful allocation of USB and display return currents are essential. GD32F103T6U6 is a documented pin-compatible alternative, but its different Flash and ADC characteristics require instrument-calibration and timing verification.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: STM32F103T6U6 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | GD32F103T6U6 |
|---|---|---|
| Manufacturer | STMicroelectronics | GigaDevice |
| Package | LQFP-48 | LQFP-48 |
| CPU Core | ARM Cortex-M3 32-bit RISC | ARM Cortex-M3 |
| Maximum Clock Frequency | 72 MHz | 108 MHz |
| Flash Memory | 32 KB | 32 KB |
| SRAM | 10 KB | 10 KB |
| USB Interface | Yes | Yes |
| CAN Interface | Yes | Yes |
| ADC Configuration | 2 ADCs; STMicroelectronics peripheral behavior | 2 ADCs; analog behavior differs and requires validation |
| Internal Core-Voltage Arrangement | STM32F103x6 implementation | 1.2 V core using an internal LDO |
主な差別化要因
- Documented 72 MHz operating ceiling （vs GD32F103T6U6)
- Established STMicroelectronics peripheral and firmware environment （vs GD32F103T6U6)
- Integrated connectivity with compact memory footprint （vs GD32F103T6U6)
設計ノート
Design the STM32F103T6U6 from its verified 2 V to 3.6 V operating range and use a regulated 2.5 V or 3.3 V rail in designs where the downstream circuitry supports it. Place the manufacturer-required input, output, and decoupling capacitors directly beside their associated pins, and provide a low-impedance ground return from the MCU and its analog references. USB, CAN, and motor-control interfaces should not share narrow supply paths with ADC-sensitive circuitry. Since the supplied data does not include detailed ESR, voltage-drop, or startup-current curves, use the STMicroelectronics datasheet and capacitor recommendations rather than estimating those values.
Use the exact STM32F103T6U6 LQFP-48 land pattern and verify all 48 pin assignments against the manufacturer package drawing before releasing the PCB. Keep analog inputs away from USB, CAN, switching-power, and motor-drive return currents, and provide a quiet ground region for ADC references. Route high-current and transient paths directly to power-entry and ground-return structures rather than through the MCU area. The verified search excerpts do not include a complete pin table, so the package library entry should not be treated as permission to infer missing power, ground, or exposed-pad connections.
Do not treat a pin-compatible footprint as proof of drop-in firmware equivalence when substituting GD32F103T6U6. The documented alternative operates up to 108 MHz rather than 72 MHz, uses zero-wait SRAM-buffered Flash, reports different ADC behavior, and employs a 1.2 V internal-LDO core arrangement. Before substitution, rebuild the project with the alternate SDK, review clock initialization and Flash wait states, compare ADC calibration and results, exercise USB, CAN, timers, and GPIO, and perform production-temperature testing. Preserve the original STM32F103T6U6 for designs requiring an unqualified ST-only supply chain.
Keep USB and CAN signal routing short, controlled, and continuous over a stable reference plane. USB requires careful impedance and routing control at the host or device interface, while CAN requires a defined network topology, termination only at intended endpoints, suitable transceiver protection, and compliance with the applicable bus specifications. Avoid routing these interfaces beneath switching nodes or across split ground planes. The MCU integrates protocol controllers rather than complete physical interfaces, so external transceivers, protection components, and passive networks remain essential to a reliable implementation.
コンプライアンス情報
The verified digchips specification identifies the device as RoHS compliant. The supplied data does not establish REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.
