STM8L162M8T6 - 8-Bit Ultra-Low-Power MCU, 64KB Flash | STMicroelectronics
部品番号: STM8L162M8T6 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.32 | $4.32 |
| 10 | $3.89 | $38.90 |
| 100 | $3.46 | $346.00 |
| 500 | $3.11 | $1,555.00 |
| 1,000 | $2.77 | $2,770.00 |
STM8L162M8T6 概要
An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, executing instructions sequentially. It integrates a processor core, memory (Flash, RAM), and peripherals (timers, UART, SPI, I2C, ADC) on one IC. In the hierarchy of embedded systems, an MCU is a type of integrated circuit, specifically a microcontroller, which falls under the broader category of semiconductors. The STM8L EnergyLite series is optimized for ultra-low-power operation, making it a key component in battery-powered and energy-harvesting designs.
Key features include multiple low-power modes (Wait, Low-power Run, Low-power Wait, Active-halt, Halt) with current consumption as low as 0.3 µA in Halt mode, a 12-bit ADC, two comparators, a real-time clock (RTC), and a wide range of communication interfaces (USART, SPI, I2C). The device also includes an LCD driver (up to 8x40 segments), a 12-bit DAC, and a DMA controller, enhancing its versatility for sensor and display applications.
The STM8L162M8T6 is built on a low-leakage CMOS process, achieving industry-leading energy efficiency. Its architecture supports fast wake-up times (as low as 4 µs) and dynamic voltage scaling, allowing designers to balance performance and power consumption. The integrated bootloader and in-application programming (IAP) capabilities simplify firmware updates in the field.
Typical applications include portable medical devices (glucose meters, pulse oximeters), smart meters, wireless sensor nodes, and industrial process control. Its ultra-low-power modes and rich analog peripherals make it ideal for battery-powered systems where every microamp matters.
When designing with this MCU, pay attention to the power supply decoupling: place a 100 nF capacitor close to each VDD pin and a 1 µF capacitor at the main supply. Use the low-power modes strategically to extend battery life, and ensure the crystal oscillator layout is clean to maintain accurate timing.
ドロップイン代替品: STM8L162M8T6 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: STM8L162M8T6 （同一形状・フットプリント） — 相違点: LCD Driver, Number of I/O Pins, RAM Size.
クイック比較ツール — 並列比較する代替部品を選択:
STM8L162M8T7
✅ ドロップイン📋 参考代替品（カタログ未掲載）
STM8L151M8T6
✅ ドロップイン📋 参考代替品（カタログ未掲載）
STM8L152M8T6
✅ ドロップイン📋 参考代替品（カタログ未掲載）
STM8L162R8T6
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
STM8L151R8T6
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
STM8L152R8T6
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.1 / 個
データシートを見る →PIC18F67K40
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
LPC824
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
STM8L162M8T6 最大定格＆電気的特性
| Core | STM8 8-bit CISC |
| 最大クロック周波数 | 16 MHz |
| Program Memory Size | 64 KB (64K x 8) Flash |
| RAM Size | 4 KB (4K x 8) |
| Data EEPROM Size | 2 KB |
| Number of I/O Pins | 68 |
| パッケージ / ケース | 80-LQFP (14x14 mm) |
| Supply Voltage Range | 1.8 V to 3.6 V |
| 動作温度範囲 | -40°C to +85°C |
| ADC Resolution | 12-bit |
| Number of ADC Channels | 28 |
| DAC Resolution | 12-bit |
| Communication Interfaces | USART, SPI, I2C |
| LCD Driver | 8x40 segments |
| Low-Power Modes | Wait, Low-power Run, Low-power Wait, Active-halt, Halt |
| Halt Mode Current | 0.3 µA (typ) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
STM8L162M8T6 ピン構成
| ピン 1 | VDD — Digital power supply |
| ピン 2 | VSS — Digital ground |
| ピン 3 | PB0 — General purpose I/O |
| ピン 4 | PB1 — General purpose I/O |
| ピン 5 | PB2 — General purpose I/O |
| ピン 6 | PB3 — General purpose I/O |
| ピン 7 | PB4 — General purpose I/O |
| ピン 8 | PB5 — General purpose I/O |
| ピン 9 | PB6 — General purpose I/O |
| ピン 10 | PB7 — General purpose I/O |
| ピン 11 | PC0 — General purpose I/O |
| ピン 12 | PC1 — General purpose I/O |
| ピン 13 | PC2 — General purpose I/O |
| ピン 14 | PC3 — General purpose I/O |
| ピン 15 | PC4 — General purpose I/O |
| ピン 16 | PC5 — General purpose I/O |
| ピン 17 | PC6 — General purpose I/O |
| ピン 18 | PC7 — General purpose I/O |
| ピン 19 | PD0 — General purpose I/O |
| ピン 20 | PD1 — General purpose I/O |
| ピン 21 | PD2 — General purpose I/O |
| ピン 22 | PD3 — General purpose I/O |
| ピン 23 | PD4 — General purpose I/O |
| ピン 24 | PD5 — General purpose I/O |
| ピン 25 | PD6 — General purpose I/O |
| ピン 26 | PD7 — General purpose I/O |
| ピン 27 | PE0 — General purpose I/O |
| ピン 28 | PE1 — General purpose I/O |
| ピン 29 | PE2 — General purpose I/O |
| ピン 30 | PE3 — General purpose I/O |
| ピン 31 | PE4 — General purpose I/O |
| ピン 32 | PE5 — General purpose I/O |
| ピン 33 | PE6 — General purpose I/O |
| ピン 34 | PE7 — General purpose I/O |
| ピン 35 | PF0 — General purpose I/O |
| ピン 36 | PF1 — General purpose I/O |
| ピン 37 | PF2 — General purpose I/O |
| ピン 38 | PF3 — General purpose I/O |
| ピン 39 | PF4 — General purpose I/O |
| ピン 40 | PF5 — General purpose I/O |
| ピン 41 | PF6 — General purpose I/O |
| ピン 42 | PF7 — General purpose I/O |
| ピン 43 | PG0 — General purpose I/O |
| ピン 44 | PG1 — General purpose I/O |
| ピン 45 | PG2 — General purpose I/O |
| ピン 46 | PG3 — General purpose I/O |
| ピン 47 | PG4 — General purpose I/O |
| ピン 48 | PG5 — General purpose I/O |
| ピン 49 | PG6 — General purpose I/O |
| ピン 50 | PG7 — General purpose I/O |
| ピン 51 | PH0 — General purpose I/O |
| ピン 52 | PH1 — General purpose I/O |
| ピン 53 | PH2 — General purpose I/O |
| ピン 54 | PH3 — General purpose I/O |
| ピン 55 | PH4 — General purpose I/O |
| ピン 56 | PH5 — General purpose I/O |
| ピン 57 | PH6 — General purpose I/O |
| ピン 58 | PH7 — General purpose I/O |
| ピン 59 | VDD — Digital power supply |
| ピン 60 | VSS — Digital ground |
| ピン 61 | NRST — Reset (active low) |
| ピン 62 | OSC_IN — Crystal oscillator input |
| ピン 63 | OSC_OUT — Crystal oscillator output |
| ピン 64 | VDDA — Analog power supply |
| ピン 65 | VSSA — Analog ground |
| ピン 66 | VREF+ — ADC reference positive |
| ピン 67 | VREF- — ADC reference negative |
| ピン 68 | PA0 — General purpose I/O |
| ピン 69 | PA1 — General purpose I/O |
| ピン 70 | PA2 — General purpose I/O |
| ピン 71 | PA3 — General purpose I/O |
| ピン 72 | PA4 — General purpose I/O |
| ピン 73 | PA5 — General purpose I/O |
| ピン 74 | PA6 — General purpose I/O |
| ピン 75 | PA7 — General purpose I/O |
| ピン 76 | PA8 — General purpose I/O |
| ピン 77 | PA9 — General purpose I/O |
| ピン 78 | PA10 — General purpose I/O |
| ピン 79 | PA11 — General purpose I/O |
| ピン 80 | PA12 — General purpose I/O |
主な用途
STM8L162M8T6 の用途: 6 件s: Portable Medical Devices, Smart Meters, Wireless Sensor Nodes, Industrial Process Control, Consumer Electronics, Automotive Body Electronics.
Portable Medical Devices
The STM8L162M8T6 is ideal for portable medical devices like glucose meters and pulse oximeters due to its ultra-low-power modes (0.3 µA Halt) and 12-bit ADC for precise sensor readings. Its 1.8V minimum supply allows operation from a single Li-ion cell, and the integrated LCD driver can display results directly. The 16 MHz core provides enough processing power for real-time signal processing, while the low-power modes extend battery life between charges. Designers can use the RTC for time-stamping measurements and the USART for data logging to an external memory.
おすすめ
Smart Meters
In smart meters, the STM8L162M8T6 excels with its integrated LCD driver (8x40 segments) for displaying consumption data, and its 12-bit ADC for accurate current/voltage sensing. The ultra-low-power modes enable battery-backed operation for decades, while the USART supports communication with PLC or RF modules. The DMA controller offloads data transfer, reducing CPU load. The wide operating voltage (1.8V-3.6V) accommodates various power supply designs, and the robust STM8 core ensures reliable operation in harsh grid environments.
おすすめ
Wireless Sensor Nodes
The STM8L162M8T6 is perfect for wireless sensor nodes in IoT applications. Its 0.3 µA Halt mode and fast wake-up (4 µs) allow duty-cycled operation, maximizing battery life. The 12-bit ADC and comparators interface with various sensors, while the SPI/I2C/USART connect to wireless modules like LoRa or Zigbee. The 64KB Flash provides ample space for communication protocols and data buffering. The small 80-LQFP package fits compact node designs, and the wide voltage range supports energy harvesting sources.
おすすめ
Industrial Process Control
For industrial process control, the STM8L162M8T6 offers robust performance with its 16 MHz core and rich analog peripherals. The 12-bit ADC and DAC enable precise control loops, while the USART supports Modbus communication. The extended temperature range (-40°C to +85°C) ensures reliability in factory environments. The multiple timers and PWM outputs can drive actuators, and the low-power modes reduce energy consumption during idle periods. The 68 I/O pins provide ample connectivity for sensors, switches, and indicators.
おすすめ
Consumer Electronics
In consumer electronics like remote controls, wearables, and smart home devices, the STM8L162M8T6 provides a cost-effective, low-power solution. Its integrated LCD driver can display time or status, and the 12-bit ADC reads battery voltage or touch sensors. The ultra-low-power modes allow devices to run for years on a coin cell. The 16 MHz core handles user interface logic and communication protocols like IR or Bluetooth (via external module). The small package and wide voltage range simplify PCB design.
おすすめ
Automotive Body Electronics
The STM8L162M8T6 is suitable for automotive body electronics like window lifters, seat control, and lighting modules. Its wide operating voltage (1.8V-3.6V) and robust I/O handle automotive supply variations. The LIN interface (via USART) enables communication with the vehicle network. The 12-bit ADC monitors switch positions and sensor inputs, while the PWM outputs drive motors or LEDs. The extended temperature variant (STM8L162M8T7) is recommended for under-hood applications. The low-power modes reduce battery drain when the vehicle is off.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: STM8L162M8T6 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | STM8L162M8T7 | STM8L151M8T6 | STM8L152M8T6 | PIC18F67K40 |
|---|---|---|---|---|---|
| Package | 80-LQFP (14x14 mm) | 80-LQFP (14x14 mm) - same | 80-LQFP (14x14 mm) - same | 80-LQFP (14x14 mm) - same | 80-LQFP (14x14 mm) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Microchip Technology |
| Core Architecture | STM8 8-bit CISC | STM8 8-bit CISC | STM8 8-bit CISC | STM8 8-bit CISC | PIC 8-bit |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 64 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 128 KB |
| RAM Size | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 10-bit |
| DAC | Yes (12-bit) | Yes (12-bit) | No | No | No |
| LCD Driver | Yes (8x40) | Yes (8x40) | No | No | No |
| Halt Mode Current | 0.3 µA | 0.3 µA | 0.3 µA | 0.3 µA | 0.02 µA |
主な差別化要因
- Integrated LCD driver (8x40 segments) （vs STM8L151M8T6)
- 12-bit DAC and DMA controller （vs STM8L152M8T6)
- Ultra-low-power Halt mode (0.3 µA) （vs PIC18F67K40)
設計ノート
Decouple each VDD pin with a 100 nF ceramic capacitor placed as close as possible to the pin. Additionally, place a 1 µF capacitor at the main power input. For analog circuits, use a separate VDDA/VSSA supply with a ferrite bead and 10 µF capacitor to reduce noise. The wide operating voltage (1.8V-3.6V) allows direct battery connection, but ensure the supply is stable during peak current draws.
For the 80-pin LQFP package, use a 4-layer PCB with a solid ground plane. Route the crystal oscillator (OSC_IN/OSC_OUT) with short traces and a ground guard ring to minimize parasitic capacitance. Keep high-speed communication lines (SPI, I2C) away from the crystal and analog pins. Use via stitching around the ground pad to improve thermal performance.
Ensure the NRST pin is pulled high with a 10 kΩ resistor and a 100 nF capacitor to ground to prevent spurious resets. When using the ADC, set the sampling time appropriately for the source impedance. Do not leave unused I/O pins floating; configure them as outputs or enable internal pull-ups. For low-power operation, disable unused peripherals and use the Halt mode with wake-up sources like the RTC or external interrupts.
コンプライアンス情報
RoHS compliant per STMicroelectronics product page. Not AEC-Q100 qualified; use STM8L162M8T7 for automotive applications requiring extended temperature.
