STM8L162M8T6 - 8-Bit Ultra-Low-Power MCU, 64KB Flash | STMicroelectronics
Артикул: STM8L162M8T6 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.32 | $4,32 |
| 10 | $3.89 | $38,90 |
| 100 | $3.46 | $346,00 |
| 500 | $3.11 | $1.555,00 |
| 1.000 | $2.77 | $2.770,00 |
STM8L162M8T6 Обзор
An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, executing instructions sequentially. It integrates a processor core, memory (Flash, RAM), and peripherals (timers, UART, SPI, I2C, ADC) on one IC. In the hierarchy of embedded systems, an MCU is a type of integrated circuit, specifically a microcontroller, which falls under the broader category of semiconductors. The STM8L EnergyLite series is optimized for ultra-low-power operation, making it a key component in battery-powered and energy-harvesting designs.
Key features include multiple low-power modes (Wait, Low-power Run, Low-power Wait, Active-halt, Halt) with current consumption as low as 0.3 µA in Halt mode, a 12-bit ADC, two comparators, a real-time clock (RTC), and a wide range of communication interfaces (USART, SPI, I2C). The device also includes an LCD driver (up to 8x40 segments), a 12-bit DAC, and a DMA controller, enhancing its versatility for sensor and display applications.
The STM8L162M8T6 is built on a low-leakage CMOS process, achieving industry-leading energy efficiency. Its architecture supports fast wake-up times (as low as 4 µs) and dynamic voltage scaling, allowing designers to balance performance and power consumption. The integrated bootloader and in-application programming (IAP) capabilities simplify firmware updates in the field.
Typical applications include portable medical devices (glucose meters, pulse oximeters), smart meters, wireless sensor nodes, and industrial process control. Its ultra-low-power modes and rich analog peripherals make it ideal for battery-powered systems where every microamp matters.
When designing with this MCU, pay attention to the power supply decoupling: place a 100 nF capacitor close to each VDD pin and a 1 µF capacitor at the main supply. Use the low-power modes strategically to extend battery life, and ensure the crystal oscillator layout is clean to maintain accurate timing.
Аналоги без доработки для STM8L162M8T6 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с STM8L162M8T6 (тот же форм-фактор и посадочное место) — отличается по LCD Driver, Number of I/O Pins, RAM Size.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
STM8L162M8T7
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM8L151M8T6
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM8L152M8T6
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM8L162R8T6
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
STM8L151R8T6
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
STM8L152R8T6
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.1 / шт.
Открыть даташит →PIC18F67K40
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LPC824
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
STM8L162M8T6 Максимальные параметры и электрические характеристики
| Core | STM8 8-bit CISC |
| Максимальная тактовая частота | 16 MHz |
| Program Memory Size | 64 KB (64K x 8) Flash |
| RAM Size | 4 KB (4K x 8) |
| Data EEPROM Size | 2 KB |
| Number of I/O Pins | 68 |
| Корпус / Типоразмер | 80-LQFP (14x14 mm) |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Диапазон рабочих температур | -40°C to +85°C |
| ADC Resolution | 12-bit |
| Number of ADC Channels | 28 |
| DAC Resolution | 12-bit |
| Communication Interfaces | USART, SPI, I2C |
| LCD Driver | 8x40 segments |
| Low-Power Modes | Wait, Low-power Run, Low-power Wait, Active-halt, Halt |
| Halt Mode Current | 0.3 µA (typ) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов STM8L162M8T6
| Контакт 1 | VDD — Digital power supply |
| Контакт 2 | VSS — Digital ground |
| Контакт 3 | PB0 — General purpose I/O |
| Контакт 4 | PB1 — General purpose I/O |
| Контакт 5 | PB2 — General purpose I/O |
| Контакт 6 | PB3 — General purpose I/O |
| Контакт 7 | PB4 — General purpose I/O |
| Контакт 8 | PB5 — General purpose I/O |
| Контакт 9 | PB6 — General purpose I/O |
| Контакт 10 | PB7 — General purpose I/O |
| Контакт 11 | PC0 — General purpose I/O |
| Контакт 12 | PC1 — General purpose I/O |
| Контакт 13 | PC2 — General purpose I/O |
| Контакт 14 | PC3 — General purpose I/O |
| Контакт 15 | PC4 — General purpose I/O |
| Контакт 16 | PC5 — General purpose I/O |
| Контакт 17 | PC6 — General purpose I/O |
| Контакт 18 | PC7 — General purpose I/O |
| Контакт 19 | PD0 — General purpose I/O |
| Контакт 20 | PD1 — General purpose I/O |
| Контакт 21 | PD2 — General purpose I/O |
| Контакт 22 | PD3 — General purpose I/O |
| Контакт 23 | PD4 — General purpose I/O |
| Контакт 24 | PD5 — General purpose I/O |
| Контакт 25 | PD6 — General purpose I/O |
| Контакт 26 | PD7 — General purpose I/O |
| Контакт 27 | PE0 — General purpose I/O |
| Контакт 28 | PE1 — General purpose I/O |
| Контакт 29 | PE2 — General purpose I/O |
| Контакт 30 | PE3 — General purpose I/O |
| Контакт 31 | PE4 — General purpose I/O |
| Контакт 32 | PE5 — General purpose I/O |
| Контакт 33 | PE6 — General purpose I/O |
| Контакт 34 | PE7 — General purpose I/O |
| Контакт 35 | PF0 — General purpose I/O |
| Контакт 36 | PF1 — General purpose I/O |
| Контакт 37 | PF2 — General purpose I/O |
| Контакт 38 | PF3 — General purpose I/O |
| Контакт 39 | PF4 — General purpose I/O |
| Контакт 40 | PF5 — General purpose I/O |
| Контакт 41 | PF6 — General purpose I/O |
| Контакт 42 | PF7 — General purpose I/O |
| Контакт 43 | PG0 — General purpose I/O |
| Контакт 44 | PG1 — General purpose I/O |
| Контакт 45 | PG2 — General purpose I/O |
| Контакт 46 | PG3 — General purpose I/O |
| Контакт 47 | PG4 — General purpose I/O |
| Контакт 48 | PG5 — General purpose I/O |
| Контакт 49 | PG6 — General purpose I/O |
| Контакт 50 | PG7 — General purpose I/O |
| Контакт 51 | PH0 — General purpose I/O |
| Контакт 52 | PH1 — General purpose I/O |
| Контакт 53 | PH2 — General purpose I/O |
| Контакт 54 | PH3 — General purpose I/O |
| Контакт 55 | PH4 — General purpose I/O |
| Контакт 56 | PH5 — General purpose I/O |
| Контакт 57 | PH6 — General purpose I/O |
| Контакт 58 | PH7 — General purpose I/O |
| Контакт 59 | VDD — Digital power supply |
| Контакт 60 | VSS — Digital ground |
| Контакт 61 | NRST — Reset (active low) |
| Контакт 62 | OSC_IN — Crystal oscillator input |
| Контакт 63 | OSC_OUT — Crystal oscillator output |
| Контакт 64 | VDDA — Analog power supply |
| Контакт 65 | VSSA — Analog ground |
| Контакт 66 | VREF+ — ADC reference positive |
| Контакт 67 | VREF- — ADC reference negative |
| Контакт 68 | PA0 — General purpose I/O |
| Контакт 69 | PA1 — General purpose I/O |
| Контакт 70 | PA2 — General purpose I/O |
| Контакт 71 | PA3 — General purpose I/O |
| Контакт 72 | PA4 — General purpose I/O |
| Контакт 73 | PA5 — General purpose I/O |
| Контакт 74 | PA6 — General purpose I/O |
| Контакт 75 | PA7 — General purpose I/O |
| Контакт 76 | PA8 — General purpose I/O |
| Контакт 77 | PA9 — General purpose I/O |
| Контакт 78 | PA10 — General purpose I/O |
| Контакт 79 | PA11 — General purpose I/O |
| Контакт 80 | PA12 — General purpose I/O |
Типичное применение
STM8L162M8T6 подходит для 6 применениеs: Portable Medical Devices, Smart Meters, Wireless Sensor Nodes, Industrial Process Control, Consumer Electronics, Automotive Body Electronics.
Portable Medical Devices
The STM8L162M8T6 is ideal for portable medical devices like glucose meters and pulse oximeters due to its ultra-low-power modes (0.3 µA Halt) and 12-bit ADC for precise sensor readings. Its 1.8V minimum supply allows operation from a single Li-ion cell, and the integrated LCD driver can display results directly. The 16 MHz core provides enough processing power for real-time signal processing, while the low-power modes extend battery life between charges. Designers can use the RTC for time-stamping measurements and the USART for data logging to an external memory.
Рекомендуется
Smart Meters
In smart meters, the STM8L162M8T6 excels with its integrated LCD driver (8x40 segments) for displaying consumption data, and its 12-bit ADC for accurate current/voltage sensing. The ultra-low-power modes enable battery-backed operation for decades, while the USART supports communication with PLC or RF modules. The DMA controller offloads data transfer, reducing CPU load. The wide operating voltage (1.8V-3.6V) accommodates various power supply designs, and the robust STM8 core ensures reliable operation in harsh grid environments.
Рекомендуется
Wireless Sensor Nodes
The STM8L162M8T6 is perfect for wireless sensor nodes in IoT applications. Its 0.3 µA Halt mode and fast wake-up (4 µs) allow duty-cycled operation, maximizing battery life. The 12-bit ADC and comparators interface with various sensors, while the SPI/I2C/USART connect to wireless modules like LoRa or Zigbee. The 64KB Flash provides ample space for communication protocols and data buffering. The small 80-LQFP package fits compact node designs, and the wide voltage range supports energy harvesting sources.
Рекомендуется
Industrial Process Control
For industrial process control, the STM8L162M8T6 offers robust performance with its 16 MHz core and rich analog peripherals. The 12-bit ADC and DAC enable precise control loops, while the USART supports Modbus communication. The extended temperature range (-40°C to +85°C) ensures reliability in factory environments. The multiple timers and PWM outputs can drive actuators, and the low-power modes reduce energy consumption during idle periods. The 68 I/O pins provide ample connectivity for sensors, switches, and indicators.
Рекомендуется
Consumer Electronics
In consumer electronics like remote controls, wearables, and smart home devices, the STM8L162M8T6 provides a cost-effective, low-power solution. Its integrated LCD driver can display time or status, and the 12-bit ADC reads battery voltage or touch sensors. The ultra-low-power modes allow devices to run for years on a coin cell. The 16 MHz core handles user interface logic and communication protocols like IR or Bluetooth (via external module). The small package and wide voltage range simplify PCB design.
Рекомендуется
Automotive Body Electronics
The STM8L162M8T6 is suitable for automotive body electronics like window lifters, seat control, and lighting modules. Its wide operating voltage (1.8V-3.6V) and robust I/O handle automotive supply variations. The LIN interface (via USART) enables communication with the vehicle network. The 12-bit ADC monitors switch positions and sensor inputs, while the PWM outputs drive motors or LEDs. The extended temperature variant (STM8L162M8T7) is recommended for under-hood applications. The low-power modes reduce battery drain when the vehicle is off.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для STM8L162M8T6 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | STM8L162M8T7 | STM8L151M8T6 | STM8L152M8T6 | PIC18F67K40 |
|---|---|---|---|---|---|
| Package | 80-LQFP (14x14 mm) | 80-LQFP (14x14 mm) - same | 80-LQFP (14x14 mm) - same | 80-LQFP (14x14 mm) - same | 80-LQFP (14x14 mm) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Microchip Technology |
| Core Architecture | STM8 8-bit CISC | STM8 8-bit CISC | STM8 8-bit CISC | STM8 8-bit CISC | PIC 8-bit |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 64 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 128 KB |
| RAM Size | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 10-bit |
| DAC | Yes (12-bit) | Yes (12-bit) | No | No | No |
| LCD Driver | Yes (8x40) | Yes (8x40) | No | No | No |
| Halt Mode Current | 0.3 µA | 0.3 µA | 0.3 µA | 0.3 µA | 0.02 µA |
Ключевые отличия
- Integrated LCD driver (8x40 segments) (против STM8L151M8T6)
- 12-bit DAC and DMA controller (против STM8L152M8T6)
- Ultra-low-power Halt mode (0.3 µA) (против PIC18F67K40)
Заметки по проектированию
Decouple each VDD pin with a 100 nF ceramic capacitor placed as close as possible to the pin. Additionally, place a 1 µF capacitor at the main power input. For analog circuits, use a separate VDDA/VSSA supply with a ferrite bead and 10 µF capacitor to reduce noise. The wide operating voltage (1.8V-3.6V) allows direct battery connection, but ensure the supply is stable during peak current draws.
For the 80-pin LQFP package, use a 4-layer PCB with a solid ground plane. Route the crystal oscillator (OSC_IN/OSC_OUT) with short traces and a ground guard ring to minimize parasitic capacitance. Keep high-speed communication lines (SPI, I2C) away from the crystal and analog pins. Use via stitching around the ground pad to improve thermal performance.
Ensure the NRST pin is pulled high with a 10 kΩ resistor and a 100 nF capacitor to ground to prevent spurious resets. When using the ADC, set the sampling time appropriately for the source impedance. Do not leave unused I/O pins floating; configure them as outputs or enable internal pull-ups. For low-power operation, disable unused peripherals and use the Halt mode with wake-up sources like the RTC or external interrupts.
Информация о соответствии
RoHS compliant per STMicroelectronics product page. Not AEC-Q100 qualified; use STM8L162M8T7 for automotive applications requiring extended temperature.
