THS4211DGN - 1GHz 970V/us Low-Distortion Op Amp | Texas Instruments
部品番号: THS4211DGN ✓ 生産中THS4211DGN 概要
A voltage-feedback operational amplifier is an analog integrated circuit that uses negative feedback to amplify a differential input while maintaining controlled gain and bandwidth. Within the broader hierarchy of a linear amplifier, a voltage-feedback amplifier, and an analog integrated circuit, this device supports signal chains that require accurate large-signal behavior rather than only low-frequency amplification. Its unity-gain stability also allows use as a general-purpose high-speed buffer.
The principal performance characteristics are a 1 GHz typical gain-bandwidth product, 970 V/µs typical slew rate, and a low-noise signal path optimized for low distortion. The device operates across a 5 V to 15 V total supply range, supports shutdown control, and has a typical quiescent current of 19 mA per channel. Maximum input offset voltage is listed as 12 mV at 25°C. These characteristics make it appropriate for wideband buffers, ADC-interface drivers, and instrumentation requiring fast settling.
The amplifier uses voltage-feedback topology rather than a decompensated architecture. According to the Texas Instruments datasheet, the combination of high slew rate, wide bandwidth, low distortion, and unity-gain stability provides higher dynamic range over a wider frequency band while avoiding the stability concerns associated with decompensated amplifiers. In practical signal chains, that combination allows the same device to handle both small-signal amplification and larger transient signals with controlled gain error.
Typical uses include high-speed ADC and DAC interface buffering, communications-channel amplification, test-and-measurement signal paths, video and imaging signal conditioning, and industrial control systems with rapid-changing sensor signals. The 970 V/µs slew rate allows the output to track fast input transitions without a separate external output-stage architecture, while the 1 GHz bandwidth provides useful bandwidth for wideband small-signal applications.
PCB design should prioritize short feedback paths, low parasitic capacitance, and a solid ground-plane connection. Place input, feedback, and decoupling components close to the device, and evaluate stability with the actual source and load impedances because high-speed feedback layouts can introduce ringing. The shutdown and supply connections should be driven cleanly to avoid unintended transitions during startup or mode changes.
This product page combines the manufacturer specifications with package guidance, application-oriented design notes, comparison parameters, and sourcing information. It helps engineers evaluate the THS4211DGN as a 1 GHz, 970 V/µs, unity-gain-stable amplifier and identify the design conditions that must be checked before placing it in a high-speed analog circuit.
ドロップイン代替品: THS4211DGN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: THS4211DGN (同一形状・フットプリント) — 相違点: Operating Temperature Range, Package, Slew Rate.
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストTHS4211DGN 最大定格&電気的特性
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 1 GHz typical |
| Slew Rate | 970 V/µs typical |
| Minimum Total Supply Voltage | 5 V |
| Maximum Total Supply Voltage | 15 V |
| 静止電流 | 19 mA per channel typical |
| Input Offset Voltage | 12 mV maximum at 25°C |
| Unity-Gain Stability | Yes |
| Shutdown Control | Yes |
| Rail-to-Rail Output | No |
| 動作温度範囲 | -40°C to +85°C |
| パッケージ | 8-pin HVSSOP (DGN) |
| 実装タイプ | Surface mount |
| ピン数 | 8 pins |
| 出力タイプ | Rail-to-rail output: No |
| Input Offset Voltage Temperature Condition | 25°C |
| Total Supply Voltage | 5 V to 15 V |
THS4211DGN 8-pin hvssop (dgn) ピン配置ガイド
THS4211DGN (8-pin hvssop (dgn) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: THS4211DGN.
詳細は データシート をご参照ください。
主な用途
THS4211DGN の用途: 6 件s: High-Speed ADC Input Buffer, Communications Signal Conditioning, Precision Instrumentation Signal Path, Industrial Sensor Interface, Video and Imaging Buffer, Test and Measurement Front End.
High-Speed ADC Input Buffer
The THS4211DGN fits between a rapidly changing analog source and a high-speed ADC because its 1 GHz typical gain-bandwidth product provides bandwidth for small-signal errors, while its 970 V/µs typical slew rate helps the output track larger transitions. The amplifier is unity-gain stable, allowing it to buffer without a decompensating gain stage when source and loading conditions support stable operation. Place the device close to the ADC input, keep the feedback loop compact, and account for ADC kickback capacitance. The non-rail-to-rail output requires separate verification that the input, output, and common-mode ranges remain valid across the full converter range.
おすすめ
Communications Signal Conditioning
The THS4211DGN is suitable for communications signal conditioning where a 1 GHz typical bandwidth and 970 V/µs typical slew rate are needed to preserve waveform shape. Its voltage-feedback architecture supports closed-loop gain control, and unity-gain stability provides flexibility for buffers as well as gain stages. For high-speed routing, use short traces, a continuous reference plane, and termination that matches the source impedance. The 12 mV maximum input offset voltage at 25°C must be evaluated against modulation and receiver accuracy requirements, while shutdown can be used during inactive intervals when the system power budget is constrained.
おすすめ
Precision Instrumentation Signal Path
The THS4211DGN can condition fast instrumentation signals where the 1 GHz gain-bandwidth product and low-distortion behavior are more valuable than the low bandwidth of a general-purpose precision amplifier. It can amplify or buffer sensor outputs, receiver front ends, and laboratory probe interfaces, provided the input common-mode range and output swing satisfy the selected supply arrangement. Because the maximum input offset voltage is 12 mV at 25°C, precision systems should include calibration or offset correction where required. High-gain operation should be checked for gain-bandwidth and stability margin, and the shutdown pin should remain controlled to avoid unexpected output movement during mode transitions.
おすすめ
Industrial Sensor Interface
The THS4211DGN is appropriate for industrial sensor interfaces that produce rapidly changing signals, including position, vibration, or process-control transducers. Its 1 GHz typical gain-bandwidth product supports wideband sensing, and the 970 V/µs typical slew rate helps minimize distortion during sharp sensor transitions. The -40°C to +85°C operating range covers many industrial environments, although enclosure temperature and power dissipation still require system-level analysis. Use a low-noise reference and ground layout, provide local supply bypassing, and keep feedback components away from switching nodes. Since the output is not rail-to-rail, verify headroom before selecting the supply configuration.
おすすめ
Video and Imaging Buffer
The THS4211DGN can serve as a high-speed buffer in video, imaging, and display signal paths where its 1 GHz typical bandwidth and 970 V/µs typical slew rate reduce timing and edge-rate distortion. Unity-gain stability supports direct buffering, and the compact 8-pin HVSSOP package can help minimize board area. Video designs must still account for DC gain accuracy, input offset, output swing, and capacitive loading. Place the amplifier close to the driven node, use a continuous ground plane, and avoid long parallel routes that increase coupling. The 5 V to 15 V supply range allows the device to fit several common analog rail arrangements without requiring a larger package.
おすすめ
Test and Measurement Front End
The THS4211DGN fits a high-speed test-and-measurement front end when the instrument must amplify small signals or buffer probes without the bandwidth limitations of a conventional precision op amp. Its 1 GHz typical gain-bandwidth product and 970 V/µs typical slew rate provide a combination of small-signal bandwidth and large-signal response. The device can operate as a unity-gain buffer or a closed-loop gain stage, subject to stability and source/load checks. For instrument-grade results, evaluate offset correction, noise, bias-current effects, and connector parasitics. Keep the input path short and controlled, and use shutdown only when the instrument can tolerate the associated settling and mode-transition behavior.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: THS4211DGN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-pin HVSSOP (DGN) |
| Brand | Texas Instruments |
| Amplifier Architecture | Voltage feedback |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 1 GHz typical |
| Slew Rate | 970 V/µs typical |
| Total Supply Voltage | 5 V to 15 V |
| Quiescent Current | 19 mA per channel typical |
| Input Offset Voltage | 12 mV maximum at 25°C |
| Unity-Gain Stability | Yes |
| Shutdown Control | Yes |
| Operating Temperature Range | -40°C to +85°C |
主な差別化要因
- High-speed closed-loop performance (vs General-purpose precision operational amplifiers)
- Unity-gain buffer capability (vs Decompensated high-speed amplifiers)
- Power management in intermittent systems (vs Amplifiers without a shutdown control)
設計ノート
Keep the op-amp feedback loop physically small and connect the feedback resistor directly between the output and inverting input. For a 1 GHz bandwidth device, long feedback traces add inductance and capacitance that can create ringing or instability. Use a continuous ground plane, avoid routing the input across split planes, and place the feedback network close to the amplifier. These layout practices are especially important because the part is unity-gain stable and may be used with minimal external compensation.
Place power-decoupling capacitors at the supply pins and connect the thermal or exposed-pad structure to the appropriate copper area using the manufacturer package guidance. High-frequency supply impedance can reduce the usable bandwidth and allow output distortion. Keep high-current return paths away from sensitive input and feedback nodes, and use short ground connections so switching currents do not share the same impedance as the signal reference.
Do not assume rail-to-rail operation: the THS4211DGN output is not rail-to-rail. Verify the input common-mode range, output swing, and supply configuration at every operating condition. Also avoid adding large capacitive loads directly to the output without stability testing. If the source impedance is high, its capacitance and noise can interact with high-speed feedback nodes and reduce phase margin.
The typical quiescent current is 19 mA per channel, before considering output-current and switching losses. Confirm that the supply regulator can support the amplifier's average and transient demand, especially when driving capacitive loads. The shutdown control can reduce consumption during inactive intervals, but its sequencing should be defined so the analog node does not float or produce an undesirable transient when the amplifier changes state.
コンプライアンス情報
Compliance attributes are not stated in the available manufacturer and distributor information. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with the manufacturer for the exact THS4211DGN order code.