Texas Instruments

THS4211DGN - 1GHz 970V/us Low-Distortion Op Amp | Texas Instruments

料号: THS4211DGN ✓ 量产中
5 V Vdss 19 mA per channel typical Id 8-pin HVSSOP (DGN) Package
最小起订量: 1 |

THS4211DGN 概述

The Texas Instruments THS4211DGN is a single-channel, unity-gain-stable voltage-feedback operational amplifier featuring 1 GHz gain-bandwidth product, 970 V/µs slew rate, and operation from 5 V to 15 V in an 8-pin HVSSOP (DGN) package. The amplifier combines broad bandwidth and fast edge response with low distortion, making it suitable for high-speed analog signal conditioning.

A voltage-feedback operational amplifier is an analog integrated circuit that uses negative feedback to amplify a differential input while maintaining controlled gain and bandwidth. Within the broader hierarchy of a linear amplifier, a voltage-feedback amplifier, and an analog integrated circuit, this device supports signal chains that require accurate large-signal behavior rather than only low-frequency amplification. Its unity-gain stability also allows use as a general-purpose high-speed buffer.

The principal performance characteristics are a 1 GHz typical gain-bandwidth product, 970 V/µs typical slew rate, and a low-noise signal path optimized for low distortion. The device operates across a 5 V to 15 V total supply range, supports shutdown control, and has a typical quiescent current of 19 mA per channel. Maximum input offset voltage is listed as 12 mV at 25°C. These characteristics make it appropriate for wideband buffers, ADC-interface drivers, and instrumentation requiring fast settling.

The amplifier uses voltage-feedback topology rather than a decompensated architecture. According to the Texas Instruments datasheet, the combination of high slew rate, wide bandwidth, low distortion, and unity-gain stability provides higher dynamic range over a wider frequency band while avoiding the stability concerns associated with decompensated amplifiers. In practical signal chains, that combination allows the same device to handle both small-signal amplification and larger transient signals with controlled gain error.

Typical uses include high-speed ADC and DAC interface buffering, communications-channel amplification, test-and-measurement signal paths, video and imaging signal conditioning, and industrial control systems with rapid-changing sensor signals. The 970 V/µs slew rate allows the output to track fast input transitions without a separate external output-stage architecture, while the 1 GHz bandwidth provides useful bandwidth for wideband small-signal applications.

PCB design should prioritize short feedback paths, low parasitic capacitance, and a solid ground-plane connection. Place input, feedback, and decoupling components close to the device, and evaluate stability with the actual source and load impedances because high-speed feedback layouts can introduce ringing. The shutdown and supply connections should be driven cleanly to avoid unintended transitions during startup or mode changes.

This product page combines the manufacturer specifications with package guidance, application-oriented design notes, comparison parameters, and sourcing information. It helps engineers evaluate the THS4211DGN as a 1 GHz, 970 V/µs, unity-gain-stable amplifier and identify the design conditions that must be checked before placing it in a high-speed analog circuit.

直接替换替代料: THS4211DGN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: THS4211DGN (相同外形与封装尺寸) ——差异在于 Operating Temperature Range, Package, Slew Rate.

Texas Instruments
Operating Temperature Range: -40 C to 85 C
Package: 8-SOIC
Slew Rate: 970 V/us
对比 THS4211DGN →
Texas Instruments
Operating Temperature Range: -40 C to 85 C
Package: 8-SOIC
Slew Rate: 970 V/us
对比 THS4211DGN →

该产品暂无直接替换替代料。

请求替代料

THS4211DGN 最大额定值与电气特性

Amplifier Type Voltage-feedback operational amplifier
Number of Channels 1 channel
Gain-Bandwidth Product 1 GHz typical
Slew Rate 970 V/µs typical
Minimum Total Supply Voltage 5 V
Maximum Total Supply Voltage 15 V
静态电流 19 mA per channel typical
Input Offset Voltage 12 mV maximum at 25°C
Unity-Gain Stability Yes
Shutdown Control Yes
Rail-to-Rail Output No
工作温度范围 -40°C to +85°C
封装 8-pin HVSSOP (DGN)
安装类型 Surface mount
引脚数 8 pins
输出类型 Rail-to-rail output: No
Input Offset Voltage Temperature Condition 25°C
Total Supply Voltage 5 V to 15 V

THS4211DGN 8-pin hvssop (dgn) 引脚配置指南

THS4211DGN(8-pin hvssop (dgn) 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

THS4211DGN 的 8-pin hvssop (dgn) 封装引脚图

暂无详细引脚数据: THS4211DGN.

请参阅 数据手册 以查看完整引脚配置。

典型应用

THS4211DGN 适用于 6 应用s: High-Speed ADC Input Buffer, Communications Signal Conditioning, Precision Instrumentation Signal Path, Industrial Sensor Interface, Video and Imaging Buffer, Test and Measurement Front End.

📊

High-Speed ADC Input Buffer

The THS4211DGN fits between a rapidly changing analog source and a high-speed ADC because its 1 GHz typical gain-bandwidth product provides bandwidth for small-signal errors, while its 970 V/µs typical slew rate helps the output track larger transitions. The amplifier is unity-gain stable, allowing it to buffer without a decompensating gain stage when source and loading conditions support stable operation. Place the device close to the ADC input, keep the feedback loop compact, and account for ADC kickback capacitance. The non-rail-to-rail output requires separate verification that the input, output, and common-mode ranges remain valid across the full converter range.

🌐

Communications Signal Conditioning

The THS4211DGN is suitable for communications signal conditioning where a 1 GHz typical bandwidth and 970 V/µs typical slew rate are needed to preserve waveform shape. Its voltage-feedback architecture supports closed-loop gain control, and unity-gain stability provides flexibility for buffers as well as gain stages. For high-speed routing, use short traces, a continuous reference plane, and termination that matches the source impedance. The 12 mV maximum input offset voltage at 25°C must be evaluated against modulation and receiver accuracy requirements, while shutdown can be used during inactive intervals when the system power budget is constrained.

🧰

Precision Instrumentation Signal Path

The THS4211DGN can condition fast instrumentation signals where the 1 GHz gain-bandwidth product and low-distortion behavior are more valuable than the low bandwidth of a general-purpose precision amplifier. It can amplify or buffer sensor outputs, receiver front ends, and laboratory probe interfaces, provided the input common-mode range and output swing satisfy the selected supply arrangement. Because the maximum input offset voltage is 12 mV at 25°C, precision systems should include calibration or offset correction where required. High-gain operation should be checked for gain-bandwidth and stability margin, and the shutdown pin should remain controlled to avoid unexpected output movement during mode transitions.

🏭

Industrial Sensor Interface

The THS4211DGN is appropriate for industrial sensor interfaces that produce rapidly changing signals, including position, vibration, or process-control transducers. Its 1 GHz typical gain-bandwidth product supports wideband sensing, and the 970 V/µs typical slew rate helps minimize distortion during sharp sensor transitions. The -40°C to +85°C operating range covers many industrial environments, although enclosure temperature and power dissipation still require system-level analysis. Use a low-noise reference and ground layout, provide local supply bypassing, and keep feedback components away from switching nodes. Since the output is not rail-to-rail, verify headroom before selecting the supply configuration.

📺

Video and Imaging Buffer

The THS4211DGN can serve as a high-speed buffer in video, imaging, and display signal paths where its 1 GHz typical bandwidth and 970 V/µs typical slew rate reduce timing and edge-rate distortion. Unity-gain stability supports direct buffering, and the compact 8-pin HVSSOP package can help minimize board area. Video designs must still account for DC gain accuracy, input offset, output swing, and capacitive loading. Place the amplifier close to the driven node, use a continuous ground plane, and avoid long parallel routes that increase coupling. The 5 V to 15 V supply range allows the device to fit several common analog rail arrangements without requiring a larger package.

🔧

Test and Measurement Front End

The THS4211DGN fits a high-speed test-and-measurement front end when the instrument must amplify small signals or buffer probes without the bandwidth limitations of a conventional precision op amp. Its 1 GHz typical gain-bandwidth product and 970 V/µs typical slew rate provide a combination of small-signal bandwidth and large-signal response. The device can operate as a unity-gain buffer or a closed-loop gain stage, subject to stability and source/load checks. For instrument-grade results, evaluate offset correction, noise, bias-current effects, and connector parasitics. Keep the input path short and controlled, and use shutdown only when the instrument can tolerate the associated settling and mode-transition behavior.

推荐产品汇总

THS4211DGN Texas Instruments 用于: High-Speed ADC Input Buffer, Communications Signal Conditioning, Precision Instrumentation Signal Path, Industrial Sensor Interface, Video and Imaging Buffer, Test and Measurement Front End THS4215 related low-distortion high-speed amplifier family member 用于: High-Speed ADC Input Buffer, Communications Signal Conditioning, Precision Instrumentation Signal Path, Industrial Sensor Interface, Video and Imaging Buffer, Test and Measurement Front End
What are the key specifications of THS4211DGN that engineers should know?
The THS4211DGN is a single-channel voltage-feedback operational amplifier with a 1 GHz typical gain-bandwidth product, 970 V/µs typical slew rate, and 5 V to 15 V supply range. It is unity-gain stable, includes shutdown control, has a typical quiescent current of 19 mA per channel, and is packaged in an 8-pin HVSSOP. According to the Texas Instruments datasheet, its combination of bandwidth, slew rate, and low distortion supports high-speed amplifier applications without requiring a decompensated amplifier configuration.
Where can I download the THS4211DGN datasheet PDF?
The official THS4211DGN datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ths4211.pdf. The manufacturer product page at https://www.ti.com/product/THS4211 also links to technical documentation, ordering information, package details, and quality information. Use the manufacturer PDF for the authoritative pin description, recommended operating conditions, electrical characteristics, typical performance curves, and application guidance.
What is the bandwidth and slew rate of THS4211DGN?
The THS4211DGN provides a 1 GHz typical gain-bandwidth product and a 970 V/µs typical slew rate. According to the Texas Instruments datasheet, the wide bandwidth supports high-frequency small-signal amplification, while the high slew rate improves tracking of large or rapidly changing signals. The device is also unity-gain stable, permitting direct use as a high-speed buffer when the load and feedback network are appropriate.
What supply voltage range does THS4211DGN operate from?
The THS4211DGN operates from a minimum total supply voltage of 5 V to a maximum total supply voltage of 15 V. According to the Texas Instruments datasheet, this range supports single-supply and split-supply arrangements when the common-mode and output-swing requirements of the selected configuration are satisfied. The device is not rail-to-rail output, so input and output headroom must be checked against the actual signal level.
Is THS4211DGN suitable for ADC signal conditioning?
Yes, the THS4211DGN is suitable for ADC signal conditioning because it combines a 1 GHz typical gain-bandwidth product with unity-gain stability and a 970 V/µs typical slew rate. It can buffer or amplify a fast sensor signal close to an ADC input, although source impedance, settling time, ADC sampling architecture, and required full-scale range must be evaluated. The manufacturer datasheet identifies high-bandwidth, low-distortion signal conditioning as a core use case.
Can THS4211DGN be used as a unity-gain buffer?
Yes, the THS4211DGN is explicitly described as unity-gain stable. According to the Texas Instruments datasheet, stability at unity gain makes it suitable for buffering high-speed signals without the stability concerns of a decompensated amplifier. The output must still be evaluated against the load capacitance and frequency because a stable voltage-feedback amplifier can require external isolation or compensation when driving unusually capacitive loads.
What is the difference between THS4211DGN and THS4211D?
The available ordering comparison identifies THS4211DGN as the 8-pin HVSSOP DGN version, while THS4211D represents a different orderable package form. Both belong to the THS4211 family and are described as high-slew-rate, unity-gain-stable voltage-feedback amplifiers for 5 V to 15 V operation. A board-level substitution should not be assumed unless the package dimensions, exposed-pad arrangement, pin mapping, thermal behavior, and orderable suffix are confirmed as identical.
When should I choose THS4211DGN over a lower-speed amplifier?
Choose the THS4211DGN when the signal path requires substantially more bandwidth or edge-rate capability than a conventional precision amplifier provides. Its 1 GHz typical gain-bandwidth product and 970 V/µs typical slew rate are valuable for fast ADC interfaces, communications paths, and instrumentation. A lower-speed amplifier may be preferable when the signal bandwidth is modest and lower power, lower noise, lower offset, or lower cost dominates the design.
What is the best drop-in replacement for THS4211DGN?
No independently verified cross-manufacturer drop-in replacement for the THS4211DGN is established by the available ordering data. A valid replacement must preserve the 8-pin HVSSOP footprint, pin mapping, exposed-pad implementation, 5 V to 15 V supply capability, shutdown behavior, and approximately 1 GHz bandwidth and 970 V/µs slew-rate performance. Use the Request a Quote form on this page to discuss an exact replacement request rather than treating a similar amplifier as a drop-in substitute.
What is the best equivalent for THS4211DGN?
The closest verified equivalent is another exact THS4211 orderable configuration, provided its mechanical package and pinout match the PCB. The cross-reference data names THS4211D, THS4211DR, THS4211DGK, and THS4211DGKR, but these are package order codes rather than independently validated cross-brand substitutes. Confirm the land pattern, thermal pad, pin names, and shutdown behavior before treating any variant as an equivalent.
What can replace THS4211DGN?
A replacement for the THS4211DGN should match its 8-pin HVSSOP pinout and provide at least comparable 1 GHz bandwidth, 970 V/µs slew rate, low distortion, and shutdown operation. The available cross-reference results do not confirm a qualified cross-brand, pin-compatible replacement, so a substitute should not be selected by amplifier category alone. Request an exact-match sourcing review through the Request a Quote form on this page.
Is THS4211DGN the same as THS4211DR?
No, THS4211DGN and THS4211DR are not automatically the same for PCB replacement because their order codes identify different package options. Both are members of the THS4211 family and share the basic voltage-feedback amplifier architecture, but package dimensions, pin mapping, and thermal-pad details must match before interchangeability can be claimed. Verify the manufacturer pinout and land pattern for the exact suffix being considered.
How much current does THS4211DGN consume?
The THS4211DGN has a typical quiescent current of 19 mA per channel. According to the Texas Instruments datasheet, this is the supply current consumed under the specified quiescent conditions rather than a guaranteed maximum across every supply voltage, temperature, and shutdown state. Actual operating current also depends on the supply voltage, output current, load, and the state of the shutdown control.
Where can I buy THS4211DGN online?
Use the Request a Quote form on this page to request THS4211DGN availability, current lead time, minimum order quantity, and commercial terms. The product is identified as an 8-pin HVSSOP Texas Instruments operational amplifier, but inventory and commercial conditions can change. The form lets the request remain tied to the exact THS4211DGN order code instead of an electrically similar amplifier.
What is the price and lead time for THS4211DGN?
Current commercial terms for the exact THS4211DGN should be requested through the Request a Quote form on this page. The form can provide the applicable unit pricing, quantity breaks, stock position, and lead-time information at the time of the request. Availability should be checked for the DGN suffix because package-specific order codes may have different inventory from other THS4211 configurations.
Does THS4211DGN support shutdown operation?
Yes, the THS4211DGN includes shutdown control, as stated in the Texas Instruments product description and family datasheet. Shutdown can reduce power consumption when the amplifier is not needed, which is useful in intermittent acquisition and communication systems. The control thresholds, timing, and permitted state transitions should be taken from the manufacturer's electrical-characteristics and pin-description tables.
What is the input offset voltage of THS4211DGN?
The maximum input offset voltage for the THS4211DGN is 12 mV at 25°C. According to the Texas Instruments datasheet, this value should be considered alongside the required system accuracy and any calibration strategy. For precision measurement chains, input bias current, input common-mode range, noise, drift, and resistor matching may be equally important and should be reviewed for the complete operating condition.

工程参考数据: THS4211DGN ——对比、设计指导和合规信息。

选型指南

Choose the THS4211DGN when a signal path needs the combination of a 1 GHz typical gain-bandwidth product, 970 V/µs typical slew rate, unity-gain stability, and shutdown control in an 8-pin HVSSOP. It is especially appropriate for ADC interfaces, high-speed instrumentation, communications conditioning, and industrial sensor paths where conventional precision amplifiers are too slow. Consider a lower-speed amplifier when the operating bandwidth is modest and lower offset, noise, power, or cost is more important. Do not substitute a similar high-speed amplifier solely by bandwidth or slew rate: confirm the DGN footprint, exposed-pad construction, pin mapping, supply limits, shutdown logic, common-mode range, output swing, and load stability. For exact sourcing of the validated package and order code, use the Request a Quote form on this page.

与替代料对比

参数 本产品
Package 8-pin HVSSOP (DGN)
Brand Texas Instruments
Amplifier Architecture Voltage feedback
Number of Channels 1 channel
Gain-Bandwidth Product 1 GHz typical
Slew Rate 970 V/µs typical
Total Supply Voltage 5 V to 15 V
Quiescent Current 19 mA per channel typical
Input Offset Voltage 12 mV maximum at 25°C
Unity-Gain Stability Yes
Shutdown Control Yes
Operating Temperature Range -40°C to +85°C

关键差异点

  • High-speed closed-loop performance (对比 General-purpose precision operational amplifiers)
  • Unity-gain buffer capability (对比 Decompensated high-speed amplifiers)
  • Power management in intermittent systems (对比 Amplifiers without a shutdown control)

设计说明

Keep the op-amp feedback loop physically small and connect the feedback resistor directly between the output and inverting input. For a 1 GHz bandwidth device, long feedback traces add inductance and capacitance that can create ringing or instability. Use a continuous ground plane, avoid routing the input across split planes, and place the feedback network close to the amplifier. These layout practices are especially important because the part is unity-gain stable and may be used with minimal external compensation.

Place power-decoupling capacitors at the supply pins and connect the thermal or exposed-pad structure to the appropriate copper area using the manufacturer package guidance. High-frequency supply impedance can reduce the usable bandwidth and allow output distortion. Keep high-current return paths away from sensitive input and feedback nodes, and use short ground connections so switching currents do not share the same impedance as the signal reference.

Do not assume rail-to-rail operation: the THS4211DGN output is not rail-to-rail. Verify the input common-mode range, output swing, and supply configuration at every operating condition. Also avoid adding large capacitive loads directly to the output without stability testing. If the source impedance is high, its capacitance and noise can interact with high-speed feedback nodes and reduce phase margin.

The typical quiescent current is 19 mA per channel, before considering output-current and switching losses. Confirm that the supply regulator can support the amplifier's average and transient demand, especially when driving capacitive loads. The shutdown control can reduce consumption during inactive intervals, but its sequencing should be defined so the analog node does not float or produce an undesirable transient when the amplifier changes state.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance attributes are not stated in the available manufacturer and distributor information. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with the manufacturer for the exact THS4211DGN order code.

数据核验日期: 2026-11-20 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

THS4211DGN datasheet THS4211DGN pinout THS4211DGN datasheet pdf THS4211DGN 1GHz amplifier THS4211DGN 970V/us THS4211DGN HVSSOP THS4211DGN ADC buffer THS4211DGN equivalent THS4211DGN replacement THS4211DGN vs THS4215 Texas Instruments THS4211DGN THS4211DGN price THS4211DGN stock THS4211DGN application circuit THS4211DGN footprint

相关元器件 & 术语

Texas Instruments THS4211DGN THS4211 THS4215 voltage-feedback operational amplifier operational amplifier linear amplifier analog integrated circuit semiconductor unity-gain stable gain-bandwidth product slew rate input offset voltage quiescent current shutdown control low distortion high-speed signal conditioning ADC interface HVSSOP DGN package surface mount SMD industrial instrumentation communications equipment
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情