Texas Instruments

THS6184PWP - Dual-Port Low-Power xDSL Line Driver | TI

部品番号: THS6184PWP ✓ 生産中
4 V to 32 V Vdss 4.2 mA per port Id 20-pin HTSSOP (PWP) Package
MOQ: 1 |

THS6184PWP 概要

The Texas Instruments THS6184PWP is a dual-port, low-power differential xDSL line-driver amplifier system with four current-feedback amplifiers, a 4 V to 32 V supply range, and a 20-pin exposed-pad HTSSOP package. Its low-bias mode consumes 4.2 mA per port while maintaining -83 dBc total harmonic distortion at 1 MHz.

An xDSL line-driver amplifier is the output stage used to drive copper telephone lines with large signal amplitudes, controlled differential voltage, and low distortion. The THS6184 combines two independent differential driver ports in one package, allowing one IC to implement four amplifiers. This integration reduces board area in ADSL, ADSL2, ADSL2+, and ADSL2++ line-card equipment while supporting the low power consumption required by high-density central-office installations.

The THS6184 architecture provides trimmed, selectable bias modes for different line lengths and operating conditions. These operating modes let a designer trade power consumption against drive performance instead of applying one fixed bias level to every subscriber line. Low-bias operation is particularly useful where shorter lines, lower signal amplitudes, or system power limits make maximum drive unnecessary. The device also supports both fixed and variable multiple-bias configurations for flexible line-card design.

Signal-chain performance is centered on current-feedback amplification and the device's low-power operating architecture. According to the Texas Instruments THS6184 datasheet, low-bias mode delivers -83 dBc THD at 1 MHz with 4.2 mA per port. This combination indicates that the driver can preserve waveform linearity while controlling dissipation. The exposed thermal pad beneath the HTSSOP package provides a direct heat-spreading path to the PCB, which is important when several driver ports operate continuously in a dense line card.

Typical deployments include ADSL and ADSL2+ subscriber-line-access equipment, central-office line cards, voice-over-DSL access nodes, and other high-density copper-access systems. Two ports per package support compact designs with four differential amplifier channels, while the low-power architecture addresses the thermal and system-level energy constraints of telecom central offices. Care must be taken to terminate unused channels and configure bias, supply decoupling, and exposed-pad grounding according to the manufacturer layout guidance.

PCB design should provide a continuous ground plane and adequate copper area beneath the exposed pad. Input and output return paths should be short and appropriately terminated to minimize parasitic feedback and preserve differential signal integrity. The power supply must remain within the 4 V to 32 V operating range, and thermal performance should be checked at the highest expected line amplitude, bias mode, ambient temperature, and port-loading condition. This page combines device functionality, operating-mode guidance, package details, and practical design considerations for engineers evaluating the THS6184PWP for xDSL line-card designs.

ドロップイン代替品: THS6184PWP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

THS6184PWPR

✅ ドロップイン
📦 HTSSOP-20 (PWP)
Tape-and-reel ordering option; electrical ratings and 20-pin footprint are otherwise equivalent, with 0 V or no measurable key-parameter change

📋 参考代替品(カタログ未掲載)

THS6184PWPG4

✅ ドロップイン
📦 HTSSOP-20 (PWP)
G4 ordering designation for the same THS6184 family; key electrical ratings remain equivalent with 0 V or no measurable key-parameter change

📋 参考代替品(カタログ未掲載)

THS6184PWP 最大定格&電気的特性

Product Type Dual-port differential xDSL line-driver amplifier system
Number of Driver Ports 2 ports
Number of Amplifiers 4 amplifiers
Supply Voltage Range 4 V to 32 V
Low-Bias Quiescent Current 4.2 mA per port
THD in Low-Bias Mode -83 dBc at 1 MHz
Amplifier Architecture Current feedback
Bias Configuration Fixed and variable multiple-bias modes
Supported Applications ADSL, ADSL2, ADSL2+, and ADSL2++ xDSL systems
パッケージ 20-pin HTSSOP (PWP)
Package Width 0.173 in (4.40 mm)
Exposed Thermal Pad Present
実装タイプ Surface mount
Temperature Grade Industrial
Total Number of Terminals 20 terminals

THS6184PWP 0.173 in (4.40 mm) ピン配置ガイド

THS6184PWP (0.173 in (4.40 mm) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

THS6184PWP の 0.173 in (4.40 mm) パッケージピン配置図

詳細なピン配置データはありません: THS6184PWP.

詳細は データシート をご参照ください。

主な用途

THS6184PWP の用途: 6 件s: ADSL Central-Office Line Cards, ADSL2+ Subscriber Access Equipment, ADSL2++ High-Density Line Cards, Voice-over-DSL Access Nodes, Copper Access Concentrator Equipment, Telecommunications Line-Card Test Equipment.

🌐

ADSL Central-Office Line Cards

The THS6184PWP is suitable for ADSL line cards because it combines two differential ports and four current-feedback amplifiers in one 20-pin HTSSOP package. Low-bias operation limits quiescent current to 4.2 mA per port while retaining -83 dBc THD at 1 MHz, helping a central office control heat and power as channel density increases. Two ports per package also reduce component count compared with separate single-channel solutions. The exposed pad should be tied to the PCB ground plane with adequate copper area, and bias should be selected for the expected line length, signal amplitude, and distortion target.

📡

ADSL2+ Subscriber Access Equipment

The THS6184PWP can drive subscriber copper lines in ADSL2+ access equipment because its four-amplifier architecture supports two differential ports within one package. Its 4 V to 32 V supply range permits use across different line-card supply architectures, while selectable bias modes allow power to be reduced where line attenuation or signal requirements permit. For a compact access node, this integration can reduce board area and assembly effort without introducing switching-converter noise into the sensitive line path. Thermal verification should include the maximum expected port activity and the thermal contribution of the exposed package pad.

🏢

ADSL2++ High-Density Line Cards

The THS6184PWP is well matched to ADSL2++ equipment where two ports and four amplifiers are packaged together for high-density line-card layouts. Its trimmed current-feedback architecture is designed to provide low distortion at low operating power, with low-bias mode specified at 4.2 mA per port and -83 dBc THD at 1 MHz. The low-power characteristic is valuable in central offices where many channels operate continuously. Designers should keep high-current output loops compact, provide low-impedance supply bypassing, and use the exposed-pad copper area as an integral part of the thermal solution.

☎️

Voice-over-DSL Access Nodes

The THS6184PWP fits Voice-over-DSL access nodes that combine high-quality copper-line drive with constrained power and board-space budgets. Four current-feedback amplifier channels are integrated as two differential ports, allowing one package to serve multiple subscriber lines. Selectable fixed and variable bias settings let the equipment optimize each line for length and required signal level rather than operating every port at maximum power. The device’s low-bias specification of 4.2 mA per port supports efficient line-card operation, while -83 dBc THD at 1 MHz provides a defined linearity benchmark for waveform-quality assessment.

🔧

Copper Access Concentrator Equipment

The THS6184PWP can serve as the line-drive element in copper access concentrators requiring several differential channels in a limited chassis area. Its dual-port organization provides four amplifiers per package, reducing the number of line-driver footprints and helping simplify routing on a dense PCB. The 4 V to 32 V operating range and selectable bias modes provide flexibility across telecom supply environments. Layout should preserve short differential traces, isolate sensitive input paths from output return currents, and connect the exposed pad to a continuous ground plane to improve both heat spreading and return-path integrity.

🖥️

Telecommunications Line-Card Test Equipment

The THS6184PWP is applicable to line-card test and simulation equipment that must reproduce differential copper-line drive levels. Its four-amplifier package can create multiple test channels, while selectable bias modes allow the drive current to be adjusted for different line lengths and test conditions. The specified -83 dBc THD at 1 MHz in low-bias mode provides a useful reference when evaluating signal-chain distortion. In instrumentation-style layouts, isolate the line driver from sensitive measurement circuits, maintain short supply and ground paths, and include thermal analysis for the maximum number of simultaneously active ports.

What is the Texas Instruments THS6184PWP?
The THS6184PWP is a dual-port, low-power differential xDSL line-driver amplifier system containing four current-feedback amplifiers. According to the Texas Instruments THS6184 datasheet, it operates from 4 V to 32 V and is packaged in a 20-pin exposed-pad HTSSOP. The device targets ADSL, ADSL2, ADSL2+, ADSL2++, and related copper-access line-card systems.
What are the key specifications of THS6184PWP that engineers should know?
The THS6184PWP combines two differential driver ports, four current-feedback amplifiers, and selectable bias modes in a 20-pin HTSSOP package. Its principal electrical specifications are a 4 V to 32 V supply range, 4.2 mA per port in low-bias mode, and -83 dBc THD at 1 MHz. The exposed pad supports heat dissipation from the package into the PCB.
What is the supply voltage range of THS6184PWP?
The THS6184PWP operates from 4 V to 32 V. According to the Texas Instruments THS6184 product documentation, this range supports line-card and telecom equipment operating from low-voltage rails through higher central-office supply buses. The design must remain within these limits while accounting for line-driver output stages and supply-decoupling tolerances.
How much current does THS6184PWP consume in low-bias mode?
The THS6184PWP consumes 4.2 mA per port in low-bias mode. The Texas Instruments THS6184 datasheet identifies this as its low-power operating condition, where it still achieves -83 dBc THD at 1 MHz. Selectable fixed and variable bias modes allow the system designer to balance line drive, distortion, and power consumption.
What does the THS6184PWP package include?
The THS6184PWP is packaged in a 20-terminal HTSSOP with an exposed pad and a body width of 0.173 in, or 4.40 mm. The exposed pad provides a thermal and electrical path to the PCB. Texas Instruments specifies a gull-wing surface-mount package, so the footprint requires 0.5 mm pitch layout and careful exposed-pad soldering.
Where can I download the THS6184PWP datasheet PDF?
The official THS6184PWP datasheet PDF is available through the Texas Instruments product-information link at https://www.ti.com/lit/gpn/ths6184. The manufacturer’s THS6184 product page also links to ordering, application, and technical information. Use the pin-description table, electrical-characteristics tables, and application circuit in that documentation when finalizing the PCB and bias configuration.
Where can I find the THS6184PWP pinout?
The authoritative THS6184PWP pin assignment is in the Texas Instruments THS6184 datasheet under the pin-configuration and pin-description sections. The device uses a 20-pin HTSSOP footprint with an exposed thermal pad. Assign all signal and power pins from the manufacturer table rather than inferring connections from similarly packaged amplifiers, because the exposed pad also has a defined electrical role.
Is THS6184PWP suitable for an ADSL2+ central-office line card?
Yes, the THS6184PWP is specifically suited to ADSL2+ and ADSL2++ systems requiring dense, low-power copper-line drive. Its two-port, four-amplifier configuration integrates four channels into one 20-pin HTSSOP package. The manufacturer identifies selectable low-bias operation as useful for reducing power in high-density central-office applications.
THS6184PWP vs THS6184PWPR - which part should I select?
Both MPNs identify the THS6184 in the 20-pin HTSSOP package, but THS6184PWPR is identified as the tape-and-reel ordering option while THS6184PWP is the base ordering designation. For PCB compatibility, confirm the manufacturer pinout and exposed-pad layout before substitution. Mechanical fit does not replace checking the orderable part details, reel orientation, and production requirements.
When should I choose THS6184PWP instead of THS6184PWPR?
Choose THS6184PWP when its manufacturer ordering configuration matches the required assembly and delivery format. THS6184PWPR is presented as the tape-and-reel version of the same THS6184 family device. The electrical architecture and 20-pin HTSSOP footprint remain the focus of comparison, while assembly packaging should be selected from the manufacturer’s current orderable-parts information.
What can replace THS6184PWP without redesigning the PCB?
A direct PCB replacement should use the same THS6184 device and 20-pin HTSSOP footprint while matching the required bias mode, electrical rating, and ordering configuration. No independently verified cross-manufacturer, pin-to-pin-compatible replacement was identified for the THS6184PWP. Treat functionally similar line drivers as new-design candidates unless their complete pinout and electrical characteristics have been formally confirmed.
Can THS6184PWPR replace THS6184PWP?
THS6184PWPR can serve as a packaging-format alternative when its orderable configuration matches the assembly process and the manufacturer confirms identical electrical specifications. Both names refer to the 20-pin HTSSOP THS6184 device, so the footprint appears compatible. Confirm the complete pin list, exposed-pad connection, reel orientation, and current orderable-parts status before approving the substitution.
Where can I buy THS6184PWP online?
Use the Request a Quote form on this page to request THS6184PWP availability, lead time, and a quotation for the required quantity. The form is the appropriate purchasing path because stock and commercial terms can change quickly. No static unit price should be used for planning without a current quote tied to the requested quantity and delivery location.
What is the price of THS6184PWP?
The current commercial price for THS6184PWP must be obtained through the Request a Quote form on this page. A quantity-specific quotation reflects the required quantity, delivery schedule, and market conditions at the time of order. Submit the exact MPN THS6184PWP with your target quantity so the supplier can confirm the correct 20-pin HTSSOP configuration.
What is the lead time and stock status for THS6184PWP?
Request current stock, minimum order quantity, and lead time through the Request a Quote form on this page. The Texas Instruments THS6184PWP product page identifies the device as an orderable family member, but individual inventory and delivery dates can vary by quantity and region. A written quotation provides the most reliable commitment for production scheduling.

エンジニアリング参考データ: THS6184PWP — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose THS6184PWP for ADSL, ADSL2, ADSL2+, ADSL2++, and copper-access line-card designs needing two differential xDSL driver ports, four current-feedback amplifiers, and selectable low-power bias modes in one package. Its 4 V to 32 V supply range and 4.2 mA-per-port low-bias specification make it appropriate for high-density telecom equipment where channel count, distortion, and power must be balanced. THS6184PWPR is the tape-and-reel ordering option and THS6184PWPG4 is the G4 ordering designation; use them when their manufacturer orderable-parts details match the assembly and procurement requirements. Neither alternative changes the functional architecture or key electrical ratings. No independently verified cross-manufacturer drop-in replacement was identified, so engineers should not substitute a generic differential amplifier without a complete pinout and electrical review.

代替品との比較

パラメータ この製品 THS6184PWPR THS6184PWPG4
Package HTSSOP-20 (PWP), exposed pad HTSSOP-20 (PWP), exposed pad HTSSOP-20 (PWP), exposed pad
Brand Texas Instruments Texas Instruments Texas Instruments
Product Type Dual-port differential xDSL line-driver amplifier system Dual-port differential xDSL line-driver amplifier system Dual-port differential xDSL line-driver amplifier system
Supply Voltage Range 4 V to 32 V 4 V to 32 V 4 V to 32 V
Driver Ports 2 ports 2 ports 2 ports
Number of Amplifiers 4 amplifiers 4 amplifiers 4 amplifiers
Low-Bias Quiescent Current 4.2 mA per port 4.2 mA per port 4.2 mA per port
THD in Low-Bias Mode -83 dBc at 1 MHz -83 dBc at 1 MHz -83 dBc at 1 MHz
Amplifier Architecture Current feedback Current feedback Current feedback
Bias Modes Fixed and variable multiple-bias settings Fixed and variable multiple-bias settings Fixed and variable multiple-bias settings

主な差別化要因

  • Four line-driver amplifiers integrated into two ports (vs THS6184PWPR)
  • Low-power operation retains specified 1 MHz linearity (vs THS6184PWPG4)
  • Wide telecom-oriented supply range (vs THS6184PWPR)
  • Compact exposed-pad thermal implementation (vs THS6184PWPG4)

設計ノート

Use the exposed pad as part of the thermal design rather than treating it as an optional copper feature. Provide a continuous ground plane beneath the HTSSOP and connect the pad to that plane with multiple low-impedance vias according to the manufacturer footprint. The pad is the principal heat-spreading path, so adequate copper area and controlled assembly solder volume are important when operating multiple ports at maximum bias.

Place supply bypass capacitors close to the device power pins and keep the high-current return path short and wide. Route differential outputs as tightly coupled pairs and keep output return currents from sharing paths with sensitive amplifier inputs. Because the HTSSOP has 0.5 mm pitch, inspect the PCB land pattern and stencil apertures carefully to avoid solder bridges between adjacent pins.

Confirm the selected bias mode against line length, output amplitude, and distortion requirements before production. Low-bias mode is specified at 4.2 mA per port with -83 dBc THD at 1 MHz, which can reduce power when maximum drive is unnecessary. Use the manufacturer’s reference termination and bias network values to preserve expected current-feedback behavior and control parasitic feedback around the high-gain output stage.

Do not assume that a similarly packaged operational amplifier is a direct replacement. The THS6184PWP is a four-amplifier dual-port line-driver system with dedicated bias-control functions, so signal pins, supply rails, thermal-pad connections, and operating modes must be checked against the manufacturer pin table. Also verify reel orientation and the exact ordering suffix when using THS6184PWPR in production.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The THS6184 is an industrial-temperature-grade telecom line-driver device. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations should be confirmed for the selected orderable suffix through the manufacturer product page.

データ検証日: 2026-11-20 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

THS6184PWP datasheet THS6184PWP datasheet pdf THS6184PWP pinout THS6184PWP equivalent THS6184PWP replacement THS6184PWP vs THS6184PWPR THS6184PWP footprint THS6184PWP price THS6184PWP stock Texas Instruments THS6184PWP THS6184PWP xDSL application circuit THS6184 4 V to 32 V line driver

関連部品&用語

Texas Instruments THS6184PWP THS6184PWPR THS6184PWPG4 xDSL ADSL ADSL2 ADSL2+ ADSL2++ differential line driver current-feedback amplifier operational amplifier line-card equipment central office low-bias mode quiescent current total harmonic distortion HTSSOP-20 PWP package exposed pad surface-mount package semiconductor telecommunications RoHS REACH
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示