TJA1055T/3/C - 125 kBd Fault-Tolerant CAN Transceiver | NXP
部品番号: TJA1055T/3/C ✗ 生産終了TJA1055T/3/C 概要
A CAN transceiver is the physical-layer interface between a digital protocol controller and a differential CAN bus. It converts controller logic levels into balanced bus signals and reconstructs a valid receive signal from the bus. Within the broader hierarchy, the TJA1055T/3/C is a CAN transceiver, a bus interface IC, an interface circuit, and a semiconductor. Its fault-tolerant design is intended to maintain communication when bus faults or unusual bus conditions occur, making it suitable for automotive body, comfort, and other low-speed distributed systems.
The principal documented characteristics include an enhanced fault-tolerant CAN architecture, differential transmission and reception, and operation to 125 kBd. The /3 ordering option is documented in the TJA1055 family as a version with a current source connected to ground for the RTH and RTL pins. Fault-tolerant operation also depends on correctly implementing the resistor network and recessive-state biasing around the transceiver.
NXP describes the TJA1055 family as an interface between the CAN protocol controller and physical bus wires in passenger cars. Its architecture supports low-speed CAN communication while adding fault-tolerance improvements relative to earlier transceivers. The /3 variant provides defined current-source behavior for the RTH and RTL pins, which is important when reproducing the reference termination and bias circuit on an existing PCB.
Typical uses include passenger-car body-control modules, door and window controllers, seat and climate-control electronics, lighting controllers, instrument-cluster peripherals, and other low-speed CAN nodes. Automotive qualification details, exact transceiver timing limits, and the full electrical limits must be checked against the complete NXP data sheet before a new production design is released.
Designers should preserve the established SO-14 footprint and pin assignments when qualifying this device. The termination-bias network, CANH and CANL routing, ground return, and protection components should follow the manufacturer application circuit. Because bus-node behavior depends on both the transceiver and external resistors, changing one network component without checking the complete termination scheme can alter dominant and recessive levels.
This product record combines the verified NXP family description, available ordering-code information, package identification, fault-tolerance characteristics, and practical replacement considerations. It also identifies where complete electrical, environmental, qualification, lifecycle, and pin-function details must be taken directly from the NXP documentation or confirmed with the manufacturer before production release.
ドロップイン代替品: TJA1055T/3/C — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TJA1055T/3/C (同一形状・フットプリント) — 相違点: Package, Primary Application.
TJA1055T/3/C,512
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TJA1055T/3/C,518
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TJA1055T/C,518
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TJA1055T/3/1J
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →TJA1055T/3/1
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →TJA1055T/3/C 仕様
| Product Type | Enhanced fault-tolerant CAN transceiver |
| Maximum Intended Data Rate | 125 kBd |
| Bus Interface | Differential CAN bus |
| CAN Protocol | Controller Area Network (CAN) |
| Transmit Function | Differential CAN transmit |
| Receive Function | Differential CAN receive |
| Primary Application | Low-speed passenger-car networks |
| Fault Tolerance | Enhanced fault-tolerant operation |
| RTH and RTL Biasing | Current source to GND for TJA1055T/3 |
| パッケージ | 14-pin SO (SOIC-14) |
| 実装タイプ | Surface mount |
| ピン数 | 14 pins |
| ESD Performance | Equal to or better than ±6 kV on CANH, CANL, RTH, and RTL under IEC-61000-4-2 test conditions |
| IEC-61000-4-2 Test Charge | 150 pF |
| IEC-61000-4-2 Test Resistance | 330 ohm |
| RoHS ステータス | unknown |
| REACH Status | unknown |
TJA1055T/3/C 14-pin so (soic-14) ピン配置ガイド
TJA1055T/3/C (14-pin so (soic-14) パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: TJA1055T/3/C.
詳細は データシート をご参照ください。
主な用途
TJA1055T/3/C の用途: 6 件s: Passenger-Car Body Control Module, Door and Window Control ECU, Automotive Lighting Controller, Seat and Climate-Control Module, Instrument-Cluster Peripheral, Legacy Vehicle Communication Retrofit.
Passenger-Car Body Control Module
The TJA1055T/3/C fits a low-speed passenger-car body-control module that communicates with door, lighting, or climate subsystems over CAN. Its documented 125 kBd maximum intended rate and enhanced fault-tolerant CAN interface suit body networks where wiring faults and node disconnection can occur. The IC handles differential transmission and reception between the controller and CANH/CANL conductors, reducing the number of external bus-driver circuits. Designers should preserve the /3 current-source arrangement around RTH and RTL, because substituting a version with pull-up bias can require different external resistor values.
おすすめ
Door and Window Control ECU
A door or window controller benefits from the TJA1055T/3/C when its distributed power and signal wiring creates a fault-tolerant low-speed CAN environment. The transceiver's differential bus interface supports communication at the documented 125 kBd ceiling, while the enhanced fault-tolerant family is intended for passenger-car networks. Use the device between the CAN controller and physical bus, and implement the RTH, RTL, CANH, CANL, and ground network exactly as shown in the NXP application circuit. Validate bus timing and fault behavior with the complete module, not only the transceiver test circuit.
おすすめ
Automotive Lighting Controller
The TJA1055T/3/C can serve as the CAN interface for an exterior or interior lighting controller in a passenger vehicle. Lighting modules often occupy distributed positions where harness damage, partial shorts, or unintended bus conditions are relevant concerns. The enhanced fault-tolerant TJA1055 architecture and differential CAN communication are intended to support these low-speed automotive networks up to 125 kBd. The circuit must preserve the manufacturer's termination-bias topology and provide suitable CAN-bus protection; the IC alone does not determine the completed harness's fault tolerance.
おすすめ
Seat and Climate-Control Module
Seat-position, HVAC, and climate electronics commonly exchange commands over a low-speed vehicle CAN network, making the TJA1055T/3/C suitable as the controller-to-bus interface. The 125 kBd rating matches the family's stated passenger-car operating focus, while differential reception improves signal integrity across an automotive harness. Keep the CAN bus traces short and controlled where practical, route the pair consistently, and maintain a low-impedance ground return. Confirm module sleep and wake behavior, bus fault responses, and the exact /3 termination network against the complete manufacturer documentation.
おすすめ
Instrument-Cluster Peripheral
A low-speed instrument-cluster peripheral can use the TJA1055T/3/C to connect a CAN controller to the vehicle's differential bus. The component provides the physical transmit and receive functions required by a CAN node, and its fault-tolerant family positioning is appropriate for passenger-car networks operating to 125 kBd. The external RTH and RTL network is essential to the intended operating behavior, especially for the /3 current-source version. Validate propagation delay, wake-up, and bus-off behavior as part of the complete cluster test, because system timing depends on the controller and network configuration.
おすすめ
Legacy Vehicle Communication Retrofit
The TJA1055T/3/C is relevant when repairing or extending an existing passenger-car CAN network that was designed around the TJA1055 /3 interface. Preserving the established SO-14 footprint and termination circuit reduces PCB modification, provided the source schematic confirms compatible electrical limits and device markings. For a safety-related retrofit, obtain manufacturer traceability and qualification evidence rather than relying only on visual marking comparison. The retrofit should also verify CAN bus speed, node termination, fault behavior, and electromagnetic compatibility under the vehicle's operating environment.
おすすめ
エンジニアリング参考データ: TJA1055T/3/C — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TJA1055T/3/C,512 | TJA1055T/3/C,518 | TJA1055T/C,518 | TJA1055T/3/1J | TJA1055T/3/1 |
|---|---|---|---|---|---|---|
| Package | 14-pin SO (SOIC-14) | 14-pin SO (SOIC-14) | 14-pin SO (SOIC-14) | 14-pin SO (SOIC-14) | 14-pin SO (SOIC-14) | 14-pin SO (SOIC-14) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | Enhanced fault-tolerant CAN transceiver | Enhanced fault-tolerant CAN transceiver | Enhanced fault-tolerant CAN transceiver | Enhanced fault-tolerant CAN transceiver | TJA1055 family CAN transceiver | TJA1055 family CAN transceiver |
| Maximum Intended Data Rate | 125 kBd | 125 kBd | 125 kBd | 125 kBd | 125 kBd | 125 kBd |
| Transmit and Receive Function | Differential CAN transmit and receive | Differential CAN transmit and receive | Differential CAN transmit and receive | Differential CAN transmit and receive | Differential CAN transmit and receive | Differential CAN transmit and receive |
| Primary Application | Low-speed passenger-car CAN networks | Low-speed passenger-car CAN networks | Low-speed passenger-car CAN networks | Low-speed passenger-car CAN networks | Low-speed passenger-car CAN networks | Low-speed passenger-car CAN networks |
| Fault-Tolerant Positioning | Enhanced fault-tolerant | Enhanced fault-tolerant | Enhanced fault-tolerant | Enhanced fault-tolerant | Enhanced fault-tolerant | Enhanced fault-tolerant |
主な差別化要因
- Defined current-source biasing for RTH and RTL (vs TJA1055T)
- Designed for enhanced fault-tolerant passenger-car CAN networks (vs TJA1055T/C,518)
- Legacy SO-14 footprint preservation (vs TJA1055T/3/C,512)
設計ノート
Do not interchange a TJA1055T/3 ordering option with a non-/3 variant without reviewing the termination network. The documented difference is that the /3 version uses a current source to ground for RTH and RTL, whereas TJA1055T uses a pull-up resistor to VCC. A change in this arrangement can require different external resistor values and may not preserve the intended fault behavior. Make the replacement decision from the original schematic and complete NXP datasheet rather than package marking alone.
Route CANH and CANL as a closely coupled differential pair and provide a continuous ground return to the transceiver. Keep the termination, RTH, RTL, protection, and transceiver connections consistent with the manufacturer application circuit. Avoid long unprotected stubs or routing the bus through areas with unrelated high-current switching paths. PCB-level geometry, connector return paths, and external protection components must be validated together because a compliant transceiver does not by itself guarantee reliable bus operation.
The manufacturer documents ESD testing on CANH, CANL, RTH, and RTL as equal to or better than ±6 kV under IEC-61000-4-2 conditions with C = 150 pF and R = 330 ohm. Treat that performance as one part of the EMC design rather than permission to omit external bus protection. Choose protection devices with suitable capacitance, clamping behavior, and speed, then verify that they do not degrade receiver thresholds, dominant levels, or fault-recovery behavior across the full vehicle harness and operating environment.
Confirm the complete supply and VIO voltage limits, decoupling requirements, and controller interface levels from the current NXP datasheet before reusing the device in a 3.3 V or 5 V logic system. Keep the regulator and decoupling path free of high-current noise sources where possible. Because this is a legacy interface IC, an unseen substitute can differ in startup, supply tolerance, and logic thresholds even when its package and nominal CAN function appear equivalent.
コンプライアンス情報
The manufacturer data sheet documents IEC-61000-4-2 ESD testing for CANH, CANL, RTH, and RTL. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not established by the available product records.