TLV2442ID - Dual Rail-to-Rail Output Op Amp | Texas Instruments
部品番号: TLV2442ID ✓ 生産中TLV2442ID 概要
An operational amplifier is a voltage-feedback amplifier used to amplify, buffer, filter, or compare small analog signals. The TLV2442 belongs to the CMOS operational-amplifier hierarchy within the broader amplifier IC and semiconductor categories. Unlike a rail-to-rail input device, the TLV2442 is specifically described by Texas Instruments as having a rail-to-rail output and wide-input-voltage range. This distinction matters when the output must approach the supply rails but the input does not need to cover both rails fully.
Key characteristics include two amplifier circuits in one package, a 2.7 V to 10 V supply range, 1.75 MHz bandwidth, and a 1.3 V/µs slew rate. The rail-to-rail output is particularly useful for driving downstream circuits that operate near a supply rail. Combining two amplifiers in one SOIC-8 package can also reduce board area and simplify dual-channel signal paths such as sensor conditioning, filtering, or differential analog front ends.
The Advanced LinCMOS implementation supports low-voltage operation while preserving useful dynamic performance for portable and embedded equipment. Bandwidth determines how quickly the closed-loop amplifier can process small-signal variations, while slew rate describes the maximum rate at which the output can change in a large-signal step. These characteristics make the TLV2442 appropriate for audio, instrumentation, communication, and control applications where the signal bandwidth remains below the amplifier’s 1.75 MHz capability.
Typical uses include low-frequency sensor amplification, active filtering, audio signal conditioning, general-purpose buffering, and dual-channel analog processing. Battery-operated products benefit from the 2.7 V minimum supply voltage because the amplifier can operate directly from a single 3.3 V rail. The same SOIC-8 package is convenient for prototypes and production assemblies requiring a conventional surface-mount footprint.
Designers should verify the input common-mode range, output swing, noise, offset, stability, and output-current capability against the manufacturer datasheet for the intended supply and load conditions. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be configured according to the recommended circuit practice. Proper grounding and short feedback paths are essential for predictable settling and reduced channel interaction.
This page combines the manufacturer’s device description with package, electrical, sourcing, replacement, and application guidance. It also identifies the limits of the available cross-reference information so that engineers can distinguish a verified drop-in option from variants that require a different footprint or a new design qualification.
ドロップイン代替品: TLV2442ID — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TLV2442ID (同一形状・フットプリント) — 相違点: Amplifier Type, Gain-Bandwidth Product, Output Swing, Package.
TLV2442AID
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2442ID 最大定格&電気的特性
| Amplifier Type | Operational Amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Technology | Advanced LinCMOS |
| Output Swing | Rail-to-rail output |
| Input Voltage Capability | Wide-input-voltage |
| Supply Voltage Range | 2.7 V to 10 V |
| Gain-Bandwidth Product | 1.75 MHz |
| Slew Rate | 1.3 V/µs |
| パッケージ | 8-pin SOIC |
| Package Pin Count | 8 pins |
| 実装タイプ | Surface mount |
| RoHS ステータス | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
TLV2442ID 8 pins ピン配置ガイド
TLV2442ID (8 pins パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TLV2442ID.
詳細は データシート をご参照ください。
主な用途
TLV2442ID の用途: 6 件s: Portable Sensor Signal Conditioning, Active Audio Filtering, Industrial Instrumentation Buffering, Communication Interface Conditioning, Battery-Powered Data Acquisition, Precision Control Signal Amplifier.
Portable Sensor Signal Conditioning
The TLV2442ID fits low-power sensor-conditioning paths because its 2.7 V to 10 V supply range permits operation from a 3.3 V system rail. Two amplifier circuits can process two related sensor channels in one 8-pin SOIC package. The 1.75 MHz gain-bandwidth product provides more closed-loop bandwidth than a basic micropower amplifier, while the 1.3 V/µs slew rate supports moderate-amplitude signal changes. The rail-to-rail output helps preserve signal swing near the positive or negative rail. Check the allowed input common-mode range, output loading, offset, and noise before selecting the gain, because those characteristics determine whether the sensor can operate across its full measurement span.
Active Audio Filtering
The TLV2442ID can implement active filters for audio and low-frequency communication signals when its 1.75 MHz gain-bandwidth product and 1.3 V/µs slew rate exceed the filter requirements. The dual configuration is useful for cascaded filter stages, balanced input conditioning, or two independent channels in a single 8-pin SOIC. Rail-to-rail output increases usable signal range in single-supply systems, while the 2.7 V minimum supply supports 3.3 V portable equipment. Set the closed-loop bandwidth from the actual noise gain rather than using the 1.75 MHz gain-bandwidth figure directly, and verify output swing into the next stage’s load.
Industrial Instrumentation Buffering
The TLV2442ID is applicable to instrumentation buffers that interface low-level analog signals to a following measurement or control stage. Its 1.75 MHz gain-bandwidth product and 1.3 V/µs slew rate provide useful response for many industrial control signals, while the dual package simplifies two-channel buffering. The 2.7 V to 10 V operating range supports both 3.3 V and 5 V industrial electronic systems. Engineers should verify input offset, bias current, noise, common-mode range, and capacitive-load stability for the sensing node. The rail-to-rail output simplifies downstream drive, but it does not make the input stage fully rail-to-rail.
Communication Interface Conditioning
The TLV2442ID can serve as a general-purpose gain and buffer stage in low-speed communication equipment. Its 1.75 MHz gain-bandwidth product is suitable for signals well below that frequency, and the 1.3 V/µs slew rate helps the output follow larger transitions. Two independent amplifiers in one 8-pin SOIC can condition transmit and receive channels or support differential buffering. A 3.3 V operating rail falls inside the stated 2.7 V to 10 V range. The designer should still account for input offset, noise, output swing, and stability when driving capacitive cable or ADC inputs, particularly if the signal has a high DC component.
Battery-Powered Data Acquisition
The TLV2442ID is a reasonable choice for low-voltage data-acquisition blocks that need two amplifiers without requiring a high-speed op amp. The 2.7 V minimum supply voltage supports 3.3 V battery-regulated systems, and the 1.75 MHz gain-bandwidth product is ample for many temperature, position, pressure, and slow analog sensor channels. Its rail-to-rail output helps retain signal range when the supply is limited. Because this is a general-purpose CMOS amplifier rather than a dedicated low-noise precision device, compare offset, drift, noise, and input bias current with the sensor error budget. Verify that each selected gain remains stable with the intended source and load impedances.
Precision Control Signal Amplifier
The TLV2442ID can amplify control and feedback signals in embedded systems where a 1.75 MHz bandwidth and 1.3 V/µs slew rate provide adequate response without a high-speed amplifier. The dual circuit arrangement allows one amplifier for error amplification and another for feedback or signal conditioning. Operating from a 3.3 V rail is possible because the specified range begins at 2.7 V, and rail-to-rail output improves drive toward the active device’s supply rail. Validate offset and drift against the control-loop accuracy requirement, then check common-mode range and output swing at the actual operating voltage. Feedback-component tolerances and board grounding also influence achievable loop gain and stability.
エンジニアリング参考データ: TLV2442ID — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV2442AID |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Amplifier Circuits | 2 circuits | 2 circuits |
| Input Capability | Wide-input-voltage | Extended common-mode input range |
主な差別化要因
- Two amplifier circuits in a compact 8-pin SOIC (vs TLV2442AID)
- Rail-to-rail output operation (vs TLV2442AID)
- Useful bandwidth and slew rate for low-voltage systems (vs TLV2442AID)
設計ノート
Route each SOIC power pin to a nearby low-impedance supply node and place the required bypass capacitors close to the device. Keep feedback resistors and compensation components adjacent to their corresponding amplifier pins to minimize parasitic capacitance and feedback-loop area. Because the TLV2442ID has two amplifier circuits in one package, treat the channels independently for layout and stability even though they share a package and supply pins.
Do not treat the rail-to-rail output specification as a guarantee that every input signal is accepted. The TLV2442ID has a wide-input-voltage input range, while its output can approach the supply rails. Before selecting the gain, verify that the input common-mode voltage remains inside the permitted range and that the output swing supports the load. This separation of input and output ranges is essential in single-supply sensor circuits whose signal can approach either rail.
The 1.75 MHz figure is a gain-bandwidth product, not a guaranteed closed-loop bandwidth at every gain setting. For a noninverting amplifier, bandwidth is approximately the gain-bandwidth product divided by noise gain; inverting configurations require the same noise-gain analysis. Also confirm that the 1.3 V/µs slew rate is adequate for the largest output step and signal frequency. Ignoring either limit can produce unexpected distortion or slow settling.
Use a supply within the specified 2.7 V to 10 V range and include local decoupling. A 3.3 V rail is a supported operating point, but output swing, input common-mode range, and output-current capability must be evaluated at 3.3 V rather than inferred from nominal supply voltage. For portable equipment, compare the complete analog-channel power budget and thermal environment against a micropower amplifier when the signal bandwidth is substantially lower than 1.75 MHz.
コンプライアンス情報
The available product information identifies the TLV2442 as an Advanced LinCMOS dual operational amplifier but does not provide specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statements.