TLV2451CD - 6V, 220kHz, 23uA RRIO Op Amp | Texas Instruments
部品番号: TLV2451CD ✓ 生産中TLV2451CD 概要
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between signals applied to its inverting and non-inverting inputs. A rail-to-rail input stage accepts input voltages extending toward the positive and negative supply rails, while a rail-to-rail output stage can produce output voltages close to those rails. Within the broader semiconductor hierarchy, the TLV2451CD belongs to the amplifier IC family and the operational-amplifier subcategory, providing analog signal conditioning ahead of measurement, control, or data-conversion stages.
The principal operating characteristics are a 6 V maximum supply, 220 kHz gain-bandwidth product, and 23 uA quiescent current. Rail-to-rail input and output capability provides useful signal-range flexibility in low-voltage circuits. These features make the device appropriate for battery-powered sensor nodes, industrial measurement interfaces, and low-voltage control systems. Its 220 kHz bandwidth supports general-purpose amplification rather than demanding high-speed video or precision signal-chain applications.
The TLV2451 is part of a broader low-power operational-amplifier family, and the TLV2451CD configuration provides one amplifier per 8-pin SOIC package. Compared with a higher-bandwidth amplifier, the TLV2451CD emphasizes lower power consumption while retaining enough bandwidth for many slow analog signals. Compared with a conventional non-rail-to-rail amplifier, its input and output stages offer greater usable range on low-voltage supplies. Designers should still verify gain stability, capacitive loading, output swing, and noise requirements for the intended feedback network and signal source.
Typical uses include bridge or thermistor sensor conditioning, current-loop signal processing, low-voltage data-acquisition front ends, portable measurement instruments, and embedded control systems powered from small batteries or low-current rails. In a sensor interface, the amplifier can convert small differential signals into a voltage suitable for an ADC or controller input. In a portable instrument, the 23 uA quiescent current helps limit continuous power demand when the signal bandwidth remains below the device's 220 kHz capability.
A practical design consideration is to check the feedback network against the required closed-loop gain and signal bandwidth, and to place the device close to its decoupling and feedback components. The power-supply pins must be bypassed as directed by the manufacturer datasheet, and input common-mode and output swing limits must be checked at the actual supply voltage and load. These checks are especially important when signals approach either supply rail.
This product page combines the manufacturer device description, exact-MPN distributor references, package information, drop-in alternatives, application guidance, and design checks to support faster engineering evaluation. It also distinguishes documented TLV2451CD characteristics from parameters that require confirmation against the current manufacturer datasheet before production release.
ドロップイン代替品: TLV2451CD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
TLV2451IDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2451AIDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2451CD 最大定格&電気的特性
| Amplifier Type | Single operational amplifier |
| 電源電圧 | 6 V maximum |
| Gain-Bandwidth Product | 220 kHz |
| 静止電流 | 23 uA per channel |
| Input Rail-to-Rail | Yes |
| Output Rail-to-Rail | Yes |
| Number of Circuits | 1 circuit |
| パッケージ | 8-pin SOIC |
| 実装タイプ | Surface mount |
| Amplifier Class | Standard general-purpose amplifier |
TLV2451CD 8-pin soic ピン配置ガイド
TLV2451CD (8-pin soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TLV2451CD.
詳細は データシート をご参照ください。
主な用途
TLV2451CD の用途: 6 件s: Battery-Powered Sensor Conditioning, Portable Instrumentation Signal Chain, Industrial Current-Sense Amplification, Low-Voltage Data-Acquisition Front End, Low-Voltage Control and Monitoring, Precision Low-Frequency Amplification.
Battery-Powered Sensor Conditioning
The TLV2451CD fits low-power sensor front ends that operate from a limited supply and produce signals near either rail. Its 23 uA quiescent current minimizes amplifier contribution to continuous battery drain, while the rail-to-rail input stage expands the usable range for sensors operating close to the supply limits. The 220 kHz gain-bandwidth product is suitable for temperature, pressure, and resistive sensor signals that change slowly. Use the amplifier with a noise gain compatible with its stability characteristics, and verify actual input bias current, offset, output swing, and sensor-source impedance before deployment.
おすすめ
Portable Instrumentation Signal Chain
The TLV2451CD is suitable for portable meters and low-current measurement instruments requiring analog amplification without a high-power amplifier. Its 23 uA quiescent current helps preserve operating time when the instrument remains on continuously, and the single-amplifier 8-pin SOIC package simplifies board partitioning. The 220 kHz gain-bandwidth product supports general-purpose measurements rather than high-frequency waveform analysis. For bridge, current-loop, or sensor-amplifier stages, select the feedback network so closed-loop noise gain remains compatible with the intended compensation and check common-mode range at the lowest supply voltage.
おすすめ
Industrial Current-Sense Amplification
The TLV2451CD can amplify a low-level current-sense voltage when the required signal bandwidth remains below its 220 kHz gain-bandwidth capability. Rail-to-rail input and output stages support operation from compact low-voltage supplies used in industrial control boards. The 23 uA quiescent current is useful in space-constrained systems where every milliamp of auxiliary load matters. Designers should calculate shunt dissipation, check input offset and bias-current effects, and ensure the amplifier remains in its linear operating region across the measured current range and common-mode excursions.
おすすめ
Low-Voltage Data-Acquisition Front End
The TLV2451CD is appropriate for conditioning slower sensor channels before an ADC in a compact data-acquisition system. Its 220 kHz gain-bandwidth product provides ample bandwidth for many low-rate measurements, and the single-8-pin-SOIC implementation leaves board area for the converter and signal routing. The low 23 uA quiescent current benefits multi-channel systems where amplifier leakage and auxiliary power affect thermal design. Confirm the ADC input range, required gain, settling behavior, and antialiasing requirements; use the manufacturer datasheet to evaluate noise, offset, and settling characteristics.
おすすめ
Low-Voltage Control and Monitoring
The TLV2451CD can buffer control signals or amplify feedback voltages in embedded systems powered from a low-current rail. Rail-to-rail input and output behavior helps retain usable signal range when the control voltage occupies much of the supply span, while 23 uA quiescent current limits the amplifier's continuous overhead. The 220 kHz bandwidth accommodates many slow control loops and monitoring thresholds. Validate stability with the actual source and load impedances, verify output-current capability, and include appropriate protection if external wiring can introduce transients beyond the device's absolute maximum conditions.
おすすめ
Precision Low-Frequency Amplification
The TLV2451CD is suitable for low-frequency precision-oriented stages when the required gain and settling performance remain within the device's 220 kHz gain-bandwidth capability. Rail-to-rail input and output stages improve flexibility on low-voltage supplies, and the single-amplifier SOIC package provides a straightforward PCB implementation. Precision applications still require review of input offset voltage, input bias current, voltage noise, current noise, and drift using the manufacturer datasheet. Resistor choice and PCB leakage can matter more than the nominal gain accuracy in high-impedance measurement circuits.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TLV2451CD — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV2451IDR | TLV2451AIDR |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier |
| Maximum Supply Voltage | 6 V | 6 V | 6 V |
| Gain-Bandwidth Product | 220 kHz | 220 kHz | 220 kHz |
| Quiescent Current | 23 uA per channel | 23 uA per channel | 23 uA per channel |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Swing | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
主な差別化要因
- Low quiescent current with moderate bandwidth (vs TLV2451IDR)
- Single-amplifier 8-pin SOIC implementation (vs TLV2451AIDR)
- Rail-to-rail signal range for low-voltage designs (vs TLV2451IDR)
設計ノート
Use the 23 uA per-channel quiescent current as the amplifier's baseline supply demand, but calculate the complete channel budget with load current, output state, and nearby circuitry. Place the bypass capacitor directly beside the supply pins and keep the return path short. Because rail-to-rail stages can draw additional current as the output approaches a rail, include worst-case output-current conditions in the supply-sizing calculation rather than relying only on the quiescent figure.
Select the feedback resistors and capacitor so the required signal gain is supported by the 220 kHz gain-bandwidth product without creating an unstable noise gain. Check the source impedance, sensor capacitance, PCB leakage, and feedback-node capacitance before finalizing high-impedance designs. For acquisition channels, confirm settling requirements with the actual gain, sampling interval, and external capacitance rather than relying on gain-bandwidth product alone.
Keep the amplifier, decoupling capacitor, feedback loop, and sensitive input nodes close together to minimize parasitic pickup and feedback-loop area. Route input signals away from supply and switching-node traces, and use a continuous ground reference beneath the signal path where practical. Verify the pin assignment against the pin-configuration drawing in the manufacturer datasheet before layout release, particularly for shutdown and supply connections.
Do not assume rail-to-rail input and output means the amplifier can accept every voltage at or beyond its supply rails. Check absolute maximum ratings, common-mode range, output swing, and output current under the worst load. Likewise, do not substitute a family member solely because it uses an 8-pin SOIC package; confirm the suffix-specific temperature grade, electrical limits, shutdown function, and qualification requirements.
コンプライアンス情報
Compliance attributes were not stated in the manufacturer or distributor excerpts and must be confirmed from the current manufacturer product documentation.