TLV2761ID - 500kHz RRIO Micro-Power Op Amp | Texas Instruments
部品番号: TLV2761ID ✓ 生産中TLV2761ID 概要
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs while using feedback to set the closed-loop gain. The TLV2761 belongs to the rail-to-rail-input/output, or RRIO, family of voltage-feedback amplifiers. Rail-to-rail input operation improves dynamic range in low-voltage systems because the input common-mode range can extend toward both supply rails, while rail-to-rail output operation provides useful output swing near the available supply limits.
The TLV2761ID combines 500 kHz bandwidth with approximately 20 µA operating current, making it suitable for portable and low-energy systems where converter size, signal bandwidth, and current consumption are all important. Its single-supply architecture supports operation from 1.8 V, a useful voltage range for coin cells, two alkaline cells, and low-voltage sensor systems. The single amplifier configuration also avoids unnecessary circuit area when only one gain stage is required.
The TLV2761 family provides rail-to-rail input and output capability in a compact low-power implementation. Its 500 kHz bandwidth is sufficient for low- and moderate-frequency precision signal paths, including sensor interfaces, current measurements, and buffered analog signals. The 20 µA operating current supports energy-efficient acquisition systems, although a design requiring high closed-loop gain must confirm that the resulting settling behavior and noise meet its bandwidth requirements.
Because the maximum recommended supply voltage is 3.6 V, the TLV2761ID should not be treated as a conventional 5 V or higher-voltage amplifier. Designators commonly use single, positive supply operation for battery-powered instrumentation. The device is available in an 8-pin SOIC package, simplifying assembly on both prototype boards and production PCBs using standard surface-mount processes.
When connecting external circuitry, keep feedback resistors close to the amplifier pins and route input and output traces away from switching nodes and high-current paths. Decoupling capacitors should connect to a low-impedance ground plane with short traces. Because RRIO amplifiers can operate close to their supply rails, input and output signals must remain within the device's absolute maximum and operating limits, including during power-up and shutdown transitions.
This page combines the Texas Instruments product specifications with practical selection, replacement, layout, and sourcing guidance. It also identifies the distinction between electrically similar TLV2761 ordering codes and explains why package, temperature grade, and shutdown capability must be checked before treating any replacement as a true drop-in choice.
ドロップイン代替品: TLV2761ID — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TLV2761ID (同一形状・フットプリント) — 相違点: Amplifier Type, Package, Operating Temperature Range, Input Common-Mode Range, Supply Voltage Range.
TLV2761CD
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2761CDG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2761ID 最大定格&電気的特性
| Amplifier Type | Single voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 1.8 V to 3.6 V recommended maximum |
| Maximum Recommended Supply Voltage | 3.6 V |
| Minimum Operating Supply Voltage | 1.8 V |
| Gain-Bandwidth Product | 500 kHz |
| Operating Current | 20 µA |
| Input Type | Rail-to-rail input |
| 出力タイプ | Rail-to-rail output |
| Supply Type | Single supply |
| 動作温度範囲 | -40°C to +85°C |
| パッケージ | 8-pin SOIC (D) |
| 実装タイプ | Surface mount |
| Product Classification | Standard general-purpose amplifier |
| Battery Compatibility | Operation from 1.8 V, suitable for two AA or AAA cells |
| Input Overvoltage Operation | Operation from ±1.8 V supplies down to ±0.9 V |
| Family Description | 1.8 V micropower rail-to-rail input/output operational amplifier |
| RoHS ステータス | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
TLV2761ID 8-pin soic (d) ピン配置ガイド
TLV2761ID (8-pin soic (d) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TLV2761ID.
詳細は データシート をご参照ください。
主な用途
TLV2761ID の用途: 6 件s: Battery-Powered Sensor Signal Conditioning, Portable Instrument Front Panel, Low-Voltage Current Sensing, Portable Medical Sensor Interface, Industrial Data Acquisition, Battery Charging and Power Monitoring.
Battery-Powered Sensor Signal Conditioning
The TLV2761ID fits low-energy sensor front ends that operate from 1.8 V and require amplification close to the sensing element. Its approximately 20 µA operating current limits the burden on the power source, while rail-to-rail input operation improves usable common-mode range in compact single-supply systems. The 500 kHz gain-bandwidth product is appropriate for many temperature, pressure, and resistive sensors that do not require megahertz bandwidth. Place the amplifier close to the sensor and its feedback network to minimize susceptible trace length. The primary trade-off is that higher closed-loop noise gain reduces actual bandwidth, so the sensor's signal bandwidth and required settling time should be checked together.
おすすめ
Portable Instrument Front Panel
The TLV2761ID can condition low-level analog inputs in handheld meters and compact measurement instruments powered from a low-voltage battery. Operation down to 1.8 V permits a compact power architecture, and the 20 µA operating current helps preserve operating time between battery replacements. Rail-to-rail output swing increases the usable measurement span when the ADC operates from the same supply. Its nominal 500 kHz bandwidth supports sensor and control paths below the amplifier's unity-gain limit, although the selected resistor values determine the actual closed-loop response. Stable references and precision resistors remain important because low-power supply and amplifier characteristics influence the complete measurement chain.
おすすめ
Low-Voltage Current Sensing
The TLV2761ID is suitable for amplifying the voltage generated by a small shunt resistor in a low-voltage current-measurement circuit. Its rail-to-rail input operation permits a wider input range near the supply rails, while approximately 20 µA operating current minimizes the amplifier's contribution to total system consumption. The 500 kHz gain-bandwidth product supports many moderate-bandwidth sensing paths, but the effective response depends on the selected shunt, closed-loop gain, and noise gain. Designers should check common-mode limits, input offset behavior, and shunt-induced heating under the maximum load. Keeping the Kelvin connection to the shunt short and symmetric improves measurement accuracy.
おすすめ
Portable Medical Sensor Interface
The TLV2761ID can serve as a low-power gain stage in a portable medical sensor interface when its operating limits match the required signal chain. A 1.8 V minimum supply and approximately 20 µA current are useful for battery-operated monitoring equipment, while rail-to-rail input and output behavior supports compact analog integration. The amplifier's 500 kHz gain-bandwidth product handles many low-bandwidth physiological and biochemical sensor signals. Medical-system designers must independently validate noise, accuracy, isolation, and regulatory requirements rather than inferring them from the amplifier specification. The amplifier should be paired with a low-noise reference, suitable input filtering, and a high-resolution ADC, with protection designed for the specific sensor connection.
おすすめ
Industrial Data Acquisition
The TLV2761ID can amplify low-level inputs in a compact industrial data-acquisition module when the module uses a low-voltage sensor bus. Its single amplifier and 8-pin SOIC package minimize board area, while 500 kHz bandwidth accommodates many process-control and monitoring signals. The approximately 20 µA operating current is valuable when several channels share a constrained power budget. Rail-to-rail inputs help when the transducer operates near the lower supply rail, but the complete input range must remain within the amplifier's operating limits. For factory equipment, include protection against transients and verify that the selected temperature grade and system isolation requirements are satisfied. Analog grounding and digital return currents should be separated to avoid injecting noise into the measurement amplifier.
おすすめ
Battery Charging and Power Monitoring
The TLV2761ID can monitor a battery-derived voltage or amplify a current-sense signal in a compact power-management subsystem. Its ability to operate from 1.8 V aligns with common battery platforms, and approximately 20 µA operating current limits continual overhead. Rail-to-rail output capability improves signal utilization when the downstream ADC shares the same restricted supply. The 500 kHz gain-bandwidth product is more than adequate for many monitoring loops, but the loop must be checked for settling at the selected closed-loop gain. Because a power rail may contain abrupt transients, use suitable filtering and protection rather than relying on the amplifier's rail-to-rail behavior for overvoltage tolerance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TLV2761ID — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV2761CD | TLV2761CDG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V |
| Maximum Recommended Supply Voltage | 3.6 V | 3.6 V | 3.6 V |
| Gain-Bandwidth Product | 500 kHz | 500 kHz | 500 kHz |
| Operating Current | 20 µA | 20 µA | 20 µA |
| Operating Temperature Range | -40°C to +85°C | 0°C to +70°C | 0°C to +70°C |
| Shutdown Function | No | Yes | Yes |
| Input and Output Type | Rail-to-rail input/output | Rail-to-rail input/output | Rail-to-rail input/output |
主な差別化要因
- Industrial-temperature operation without a shutdown feature (vs TLV2761CD)
- Same low-power core in the same SOIC footprint (vs TLV2761CDG4)
- Designed for the broadest industrial temperature range in the documented comparison (vs TLV2761CDG4)
設計ノート
Place the supply-decoupling capacitor directly between the TLV2761ID supply and ground pins, with the ground connection made through the shortest possible path. Keep the two feedback resistors near the amplifier rather than at the source or load. Sensitive input traces should be separated from switching-node traces, and the complete analog signal path should reference a continuous ground plane to reduce parasitic pickup and common-mode conversion.
Design the supply rail for no more than the 3.6 V maximum recommended operating voltage. If the source is a battery or low-voltage regulator, include margin for charging voltage, transient overshoot, and component tolerance. The approximately 20 µA amplifier current is favorable for portable systems, but total supply demand also includes the output-load current and external bias paths, which must be checked separately.
Account for the closed-loop bandwidth rather than assuming the full 500 kHz gain-bandwidth product is available at every gain setting. High-gain configurations use more noise gain and therefore settle more slowly. For a sampled measurement system, verify the required acquisition time and include anti-alias filtering. Rail-to-rail operation does not remove the need to keep input and output voltages inside the specified common-mode and output-swing ranges.
Do not substitute TLV2761CD for TLV2761ID solely because both use an 8-pin SOIC footprint. The CD ordering code adds shutdown and uses a narrower commercial temperature range, so it can change board behavior and fail an industrial temperature requirement. Conversely, a design requiring shutdown cannot use TLV2761ID unchanged. Verify the exact pin connection, shutdown state, and temperature grade against the Texas Instruments family datasheet before approving a replacement.
コンプライアンス情報
The TLV2761ID is an industrial-temperature general-purpose amplifier. Compliance declarations should be confirmed using the current manufacturer product page and applicable material declarations.