TLV2784ID - 3.6V 8MHz Quad RRIO Op Amp | Texas Instruments
部品番号: TLV2784ID ✗ 生産終了TLV2784ID 概要
An operational amplifier is a voltage-controlled differential amplifier whose gain, filtering, buffering, and level-shifting behavior support the analog signal chain between sensors, converters, and digital processors. The TLV2784 belongs to the hierarchy of operational amplifier, rail-to-rail input/output amplifier, analog amplifier IC, and power-management-sensitive signal-conditioning component. Its low-voltage operation is useful for battery-powered, portable, industrial, and embedded systems where analog circuitry must operate efficiently from compact supply rails.
Key features include four amplifier channels, an 8 MHz gain-bandwidth product, 1.8 V minimum family operation, rail-to-rail inputs and outputs, and a 3.6 V nominal supply characterized by the manufacturer. The rail-to-rail input stage accepts signals spanning the supply range, while the rail-to-rail output stage improves dynamic range in low-voltage systems. The -40°C to 125°C temperature rating supports industrial environments where a commercial-temperature amplifier could limit operating margins.
The TLV2784ID combines four high-speed amplifiers with a compact 14-pin SOIC footprint. Its 8 MHz bandwidth is appropriate for general-purpose signal amplification, active filtering, buffer stages, and low-to-moderate-frequency closed-loop applications. Four channels in one package can also simplify board partitioning when several sensors or analog nodes require consistent amplification. Designers should still verify output-current demand, capacitive-load stability, noise, slew rate, and loop gain against the manufacturer datasheet before finalizing a high-gain or large-capacitance design.
Typical applications include industrial sensor interfaces, portable measurement systems, audio and communication signal conditioning, low-voltage data acquisition, and instrumentation control loops. In a four-channel sensor board, each amplifier can condition a separate input while the 14-pin package reduces routing complexity. For battery-operated equipment, the 1.8 V-capable architecture permits analog processing from a low rail, although total supply current and output drive must be checked for the intended load.
A key design consideration is that rail-to-rail operation changes with input and output common-mode conditions. Place bypass capacitors close to the supply pins, keep feedback loops compact, and avoid excessive capacitive loading directly on the output. Review the pin-description table in the manufacturer datasheet when assigning PCB tracks. Because TLV2784ID is no longer in production, engineers should also validate lifecycle risk, traceability, and any replacement against the original design requirements.
This page combines lifecycle information, pin-level implementation guidance, same-footprint replacement options, and engineering-oriented application analysis for engineers evaluating the TLV2784ID quad operational amplifier.
ドロップイン代替品: TLV2784ID — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
TLV2784AIDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2784CDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV274IDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV272CDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2784ID 最大定格&電気的特性
| Amplifier Count | 4 channels |
| Nominal Supply Voltage | 3.6 V |
| Minimum Family Operating Supply | 1.8 V |
| Gain-Bandwidth Product | 8 MHz |
| Input Type | Rail-to-rail |
| 出力タイプ | Rail-to-rail |
| 動作温度範囲 | -40°C to 125°C |
| パッケージ | SOIC-14 (D) |
| ピン数 | 14 pins |
| 実装タイプ | Surface mount |
TLV2784ID ピン構成
| ピン 1 | OUTA — Channel A output |
| ピン 2 | INA- — Channel A inverting input |
| ピン 3 | INA+ — Channel A noninverting input |
| ピン 4 | V+ — Positive supply connection |
| ピン 5 | INB+ — Channel B noninverting input |
| ピン 6 | INB- — Channel B inverting input |
| ピン 7 | OUTB — Channel B output |
| ピン 8 | OUTC — Channel C output |
| ピン 9 | INC- — Channel C inverting input |
| ピン 10 | INC+ — Channel C noninverting input |
| ピン 11 | V- — Negative supply connection |
| ピン 12 | IND+ — Channel D noninverting input |
| ピン 13 | IND- — Channel D inverting input |
| ピン 14 | OUTD — Channel D output |
主な用途
TLV2784ID の用途: 6 件s: Industrial Sensor Signal Conditioning, Portable Measurement Systems, Low-Voltage Data Acquisition, Audio and Communication Buffering, Active Filtering and Control Loops, Legacy Equipment Repair.
Industrial Sensor Signal Conditioning
The TLV2784ID fits four-channel industrial sensor conditioning because it combines four rail-to-rail input/output amplifiers with an 8 MHz gain-bandwidth product in one 14-pin SOIC package. Each channel can amplify a sensor signal, buffer an ADC input, or provide active filtering when the required closed-loop bandwidth remains within the amplifier's capabilities. The -40°C to 125°C temperature rating supports demanding industrial environments, while operation from a 1.8 V family supply enables low-voltage acquisition circuits. Designers should confirm input offset, bias current, noise, output drive, and capacitive-load stability in the family datasheet before fixing the gain and filtering values.
おすすめ
Portable Measurement Systems
The TLV2784ID is useful in portable measurement equipment that needs several buffered analog channels without adding four separate packages. Its 1.8 V family capability allows operation from compact supply rails, while the rail-to-rail input and output stages provide signal range close to the supply limits. The four channels can serve sensor amplifiers, filter stages, and output drivers within the same board. Battery-operated designs must account for total quiescent current and load demand, and designers should verify noise and offset performance against the required measurement resolution before selecting resistor and capacitor values.
おすすめ
Low-Voltage Data Acquisition
The TLV2784ID can condition multiple inputs in a low-voltage data-acquisition system because it provides four rail-to-rail amplifiers, an 8 MHz bandwidth rating, and operation in the TLV2784 family down to 1.8 V. A typical arrangement places one amplifier in front of each converter channel for gain, level shifting, or active filtering. The wide common-mode capability can simplify sensing around mid-supply signals, but actual input range, output swing, and stability depend on the chosen gain and load. Review the electrical characteristics and stability plots in the manufacturer datasheet before operating the amplifier near its supply rails.
おすすめ
Audio and Communication Buffering
The TLV2784ID can buffer or amplify low-level signals in communication and audio-control paths where 3.6 V operation and rail-to-rail I/O are useful. Its 8 MHz gain-bandwidth product supports general-purpose amplification and moderate-bandwidth filtering, while the 14-pin quad package consolidates four channels into one component. This can be advantageous when several buffers share the same supply and require comparable bandwidth. The design must preserve signal headroom, prevent overload near the output limits, and maintain adequate loop stability with the chosen feedback network and load capacitance.
おすすめ
Active Filtering and Control Loops
The TLV2784ID can implement active filters and general-purpose control loops when the required signal bandwidth is compatible with its 8 MHz gain-bandwidth product. Four channels allow independent filter sections or coordinated control and monitoring functions within a single 14-pin SOIC outline. Component tolerances, op-amp gain behavior, and the selected noise gain determine the resulting filter response. Confirm the loop gain, phase margin, output-current capability, and capacitive-load limits against the manufacturer stability guidance before increasing Q or driving long external cables.
おすすめ
Legacy Equipment Repair
The TLV2784ID is relevant to repair and modernization work involving boards built with the original Texas Instruments TLV2784 quad amplifier. Its 14-pin SOIC package and four-amplifier arrangement make it possible to reproduce the original circuit topology without changing the footprint. Because the ordering option is no longer in production, procurement should emphasize lot traceability, visual inspection, and functional testing rather than availability alone. Before substituting another family member, engineers must compare pin functions, supply limits, common-mode behavior, stability, and electrical performance with the original circuit requirements.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TLV2784ID — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV2784AIDR | TLV2784CDR | TLV274IDR | TLV272CDR |
|---|---|---|---|---|---|
| Package | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
主な差別化要因
- Four channels in one 14-pin SOIC package (vs TLV274IDR)
- Direct same-family replacement path (vs TLV2784AIDR)
- Extended industrial temperature specification (vs TLV2784CDR)
設計ノート
Place the positive and negative supply bypass capacitors close to the corresponding power pins and ground reference. Keep amplifier feedback resistors and compensation capacitors near the associated pins to minimize parasitic inductance and capacitance. For a multi-channel design, route each channel to reduce shared-impedance coupling, because input and output currents returning through imperfect ground paths can degrade the benefit expected from the quad package.
Treat rail-to-rail input and output operation as a design range rather than a guarantee of unlimited bandwidth. At common-mode levels near either supply rail, the transition region and distortion performance can differ from the nominal operating region. Use the manufacturer input common-mode and output swing characteristics, and verify the selected gain, signal amplitude, and load with an oscilloscope before releasing a precision or high-speed design.
Do not assume that every 14-pin SOIC quad amplifier is electrically interchangeable with the TLV2784ID. Check shutdown behavior, supply range, input bias current, offset voltage, noise, slew rate, output-current capability, and capacitive-load stability. For replacement of the discontinued TLV2784ID, preserve the original footprint, verify every connected function, and perform temperature-range testing on the assembled board.
コンプライアンス情報
The manufacturer product and ordering pages identify the TLV2784ID and its operating characteristics, but the documented data does not establish the requested compliance values.