STMicroelectronics

TS3702IN - Micropower Dual Comparator | STMicroelectronics

部品番号: TS3702IN ✓ 生産中
16 V Vdss 9 µA per comparator Id PDIP-8, 8-pin through-hole Package
MOQ: 1 |

TS3702IN 概要

STMicroelectronics TS3702IN is a micropower dual CMOS voltage comparator with 9 µA typical supply current per comparator, 1.5 µs maximum response time, and 6.5 mV maximum input offset voltage in an 8-pin PDIP package. Its two independent comparator channels use push-pull CMOS outputs, eliminating the external pull-up resistor normally required by open-collector comparators.

A voltage comparator is an analog mixed-signal component that compares two input voltages and produces a logic-level output indicating which input is higher. The TS3702IN belongs to the comparator hierarchy within integrated circuits and analog signal-conditioning ICs. Its micropower operating current makes it suitable for battery-powered equipment where continuous supply consumption must remain low, while its dual-channel configuration provides two comparison functions in one package.

The principal features are low power consumption, CMOS-compatible push-pull outputs, low input offset voltage, and a response time suitable for general-purpose signal detection. According to the STMicroelectronics TS3702 product page, the TS3702 consumes 9 µA typical per comparator, approximately twenty times less than a bipolar LM393. The 16 V maximum supply rating provides headroom for conventional 5 V and low-voltage industrial systems, while the 600 pA input bias current limits disturbance of high-impedance sensing nodes.

Internally, the device combines CMOS input stages with two independent comparator channels. The push-pull output architecture actively drives both logic states, making the outputs suitable for direct connection to compatible CMOS inputs. This differs from open-collector comparators, which require an external pull-up resistor and can present slower rising edges when additional capacitance must be charged. Board designers should still check the output timing and load limits in the manufacturer datasheet when driving unusually long traces or high-capacitance nodes.

Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, window comparators, and simple control loops. A second application is industrial sensing where low 9 µA typical current per comparator helps limit standby consumption. The TS3702IN can also supervise a divided supply rail by comparing its scaled voltage against a reference derived from another node.

The principal design consideration is logic compatibility. Push-pull outputs must not be tied together or connected to a pull-up resistor in the manner used with open-collector outputs. Input common-mode range, output voltage levels, and propagation-delay limits must be checked against the actual supply voltage and connected logic family before finalizing the circuit.

This product page combines the manufacturer specifications with package, sourcing, and replacement guidance for engineers evaluating the TS3702IN. It also identifies drop-in alternatives that retain the same 8-pin through-hole footprint, helping PCB designers compare functionality without introducing an unintended package migration.

ドロップイン代替品: TS3702IN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: TS3702IN (同一形状・フットプリント) — 相違点: Comparator Type, Output Type, Package.

STMicroelectronics
Comparator Type: General-purpose voltage comparator
Output Type: CMOS push-pull
Package: 8-pin DIP
比較対象 TS3702IN →

TS3702CN

✅ ドロップイン
STMicroelectronics
📦 PDIP-8
General-purpose voltage comparator · 2 channels · 9 µA typical · 6.5 mV maximum · 1.5 µs maximum · CMOS push-pull · CMOS · ±1.35 V to ±8 V

価格はお問い合わせください

データシートを見る →

TLC3702CP

✅ ドロップイン
📦 PDIP-8
Cross-brand micropower dual push-pull comparator; exact output timing and input-offset differences are not quantified in the available comparison data

📋 参考代替品(カタログ未掲載)

TLC3702IP

✅ ドロップイン
📦 PDIP-8
Cross-brand industrial-temperature micropower dual push-pull comparator; exact response-time and offset-voltage differences are not quantified in the available comparison data

📋 参考代替品(カタログ未掲載)

TS3702IN 最大定格&電気的特性

Comparator Type Dual general-purpose voltage comparator
Number of Channels 2 channels
Maximum Supply Voltage 16 V
Typical Supply Current 9 µA per comparator
Input Offset Voltage 6.5 mV maximum
Response Time 1.5 µs maximum
Input Bias Current 600 pA maximum
出力タイプ Push-pull CMOS
Logic Technology CMOS
Independent Comparators 2 independent channels
パッケージ PDIP-8, 8-pin through-hole
実装タイプ Through-hole
Input Pin Count 5 inputs, including 2 ground pins

TS3702IN pdip-8, 8-pin through-hole ピン配置ガイド

TS3702IN (pdip-8, 8-pin through-hole パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

TS3702IN の pdip-8, 8-pin through-hole パッケージピン配置図

詳細なピン配置データはありません: TS3702IN.

詳細は データシート をご参照ください。

主な用途

TS3702IN の用途: 6 件s: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Supply Overvoltage Monitoring, Window Comparator, Portable Medical Sensor Interface, Smart Home and IoT Limit Detection.

⚡

Battery-Powered Threshold Detection

The TS3702IN is well matched to battery-powered threshold detection because each comparator consumes 9 µA typical while providing a 1.5 µs maximum response time. Place one channel across a divided sensor or supply signal and the other across the corresponding threshold to create an alert or control output. The 600 pA maximum input bias current minimizes disturbance of high-impedance dividers, while push-pull outputs drive compatible CMOS logic without a pull-up resistor. Check the common-mode input range at the minimum battery voltage before finalizing the thresholds.

🏭

Industrial Sensor Signal Conditioning

The TS3702IN can condition weak or offset industrial sensor signals with its dual independent comparator channels and 600 pA maximum input bias current. One channel can compare the sensor output with an adjustable threshold, while the other can monitor an alarm or fault condition. The 6.5 mV maximum offset specification helps define the comparison uncertainty around a small signal, and the 1.5 µs maximum response time supports prompt logic decisions. The push-pull output simplifies interfacing with compatible control logic, although the input common-mode range must cover the sensor’s operating voltage.

🔋

Supply Overvoltage Monitoring

Use the TS3702IN as a low-power supply supervisor when a monitored rail must be compared with a scaled reference. Two independent channels permit separate overvoltage and undervoltage decisions, creating a window-comparator function without two separate ICs. The 16 V maximum supply rating provides useful headroom around conventional low-voltage rails, and the 9 µA typical consumption per comparator limits continuous monitoring overhead. Divider resistance must balance reference accuracy against leakage, while the comparator input common-mode range and output levels must be checked at startup and fault conditions.

📊

Window Comparator

The two independent TS3702IN channels can form a window comparator in which one output indicates an above-limit condition and the other indicates a below-limit condition. This arrangement is useful for battery packs, signal ranges, and adjustable set points that must remain between two boundaries. With a 1.5 µs maximum response time and 6.5 mV maximum input offset voltage, the device can provide fast general-purpose threshold decisions. Logic combining should account for output polarity, and both channels must remain inside their valid input common-mode range during every monitored transition.

💊

Portable Medical Sensor Interface

The TS3702IN can support threshold decisions around portable medical-sensor signals where continuous comparator current must remain low. Its 9 µA typical consumption per channel and 600 pA maximum input bias current help preserve weak sensor signals and reduce energy use. The dual arrangement can monitor a physiological signal boundary or compare a sensor-derived value with a reference level. For medical equipment, the complete signal chain must satisfy the applicable system quality and safety requirements; use the manufacturer datasheet to verify electrical limits and qualify the finished design independently of the comparator.

🧩

Smart Home and IoT Limit Detection

The TS3702IN fits IoT and smart-home modules that need continuous limit detection without the higher standby current of a bipolar comparator. One channel can identify a sensor threshold crossing, while the other can supervise a divided local supply. The push-pull outputs can connect directly to compatible CMOS logic, avoiding the external pull-up resistor required by open-collector implementations. The 600 pA maximum input bias current is advantageous for high-impedance sensing networks, but divider leakage, the supported input voltage range, and the module’s sleep strategy should be evaluated together for long battery life.

おすすめ製品の概要

TS3702CN STMicroelectronics 使用用途: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Supply Overvoltage Monitoring, Window Comparator, Portable Medical Sensor Interface, Smart Home and IoT Limit Detection TLC3702CP Micropower dual push-pull comparator candidate 使用用途: Battery-Powered Threshold Detection, Supply Overvoltage Monitoring, Portable Medical Sensor Interface TLC3702IP Cross-brand micropower comparator candidate 使用用途: Industrial Sensor Signal Conditioning, Window Comparator, Smart Home and IoT Limit Detection
What is the TS3702IN and what are its main specifications?
The TS3702IN is a micropower dual CMOS voltage comparator with 9 µA typical supply current per comparator, 6.5 mV maximum input offset voltage, and 1.5 µs maximum response time. According to the STMicroelectronics TS3702 product page and manufacturer datasheet, it is packaged as an 8-pin PDIP device and uses push-pull CMOS outputs. The two channels operate independently, allowing threshold detection, window comparison, or two separate signal-monitoring functions in one package.
How much current does the TS3702IN consume?
The TS3702IN consumes 9 µA typical per comparator, according to the STMicroelectronics TS3702 product page. That means a dual device has a typical total supply current of approximately 18 µA when both channels are operating, subject to the exact test conditions in the manufacturer datasheet. The manufacturer describes this consumption as approximately twenty times lower than a bipolar LM393 comparator, making the device useful for low-power sensing and battery-operated equipment.
Where can I download the TS3702IN datasheet PDF?
The official TS3702IN datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/ts3702.pdf. The document is titled “Micropower dual CMOS voltage comparators” and applies to the TS3702 family, including the TS3702IN PDIP ordering configuration. Use the manufacturer document for the authoritative pin description, electrical limits, timing characteristics, common-mode limits, and application guidance rather than relying on a distributor summary.
Where can I find the TS3702IN pinout and package information?
The TS3702IN uses an 8-pin PDIP package, and its functional pin assignments are shown in the pin configuration section of the STMicroelectronics TS3702 datasheet. The package contains two comparator channels, five input-related pins because the two channels share ground, and one push-pull output per channel. Use the datasheet pin-description table when assigning PCB tracks, especially to verify the common ground arrangement and the input associated with each output.
What is the response time of the TS3702IN comparator?
The TS3702IN has a 1.5 µs maximum response time, according to the manufacturer datasheet and the component specifications published for TS3702IN. This timing makes the dual comparator suitable for general-purpose threshold detection rather than only static slow-level comparison. The response-time limit should be checked against the applied overdrive and supply conditions specified by STMicroelectronics, particularly in designs where propagation delay directly affects a control decision.
Does the TS3702IN use push-pull or open-collector outputs?
The TS3702IN uses push-pull CMOS outputs. According to the STMicroelectronics manufacturer datasheet, the active output stage eliminates the external pull-up resistor normally associated with open-collector comparators. This can simplify interfacing to compatible CMOS logic and avoid a resistor-dependent rising edge. Because each output actively sources and sinks current, outputs from different channels must not be wired together, and external pull-up resistors should not be added unless required by a specific interface requirement.
TS3702IN vs TS3702CN: which dual comparator should I choose?
The TS3702IN and TS3702CN are closely related 8-pin dual micropower CMOS comparators, but temperature-grade details must be confirmed from the ordering table before substitution. The manufacturer product page identifies the TS3702 family as having 9 µA typical consumption per comparator, while the cross-reference record confirms that TS3702CN uses the same PDIP-8 format. TS3702IN is the appropriate selection when its specified temperature range matches the product requirements; otherwise, use the exact suffix whose ratings apply.
TS3702IN vs TLC3702CP: are they drop-in alternatives?
The TS3702IN and TLC3702CP are both micropower dual voltage comparators offered in 8-pin through-hole packages, but final interchangeability depends on the complete pin, voltage, timing, and output specification. The TI TLC3702 family is described as a dual micropower push-pull LinCMOS comparator, supporting functional similarity to the TS3702. Treat TLC3702CP as a candidate drop-in replacement only after checking polarity, input common-mode range, output levels, response timing, and supply limits against the original design.
When should I choose the TS3702IN over another dual comparator?
Choose the TS3702IN when the design requires two independent general-purpose comparison channels, approximately 9 µA typical supply current per comparator, and push-pull CMOS outputs in an 8-pin PDIP package. It is particularly appropriate for low-power threshold monitoring where an open-collector pull-up would add unnecessary components. Select another candidate only when its supply rating, common-mode range, propagation delay, input offset, or qualification requirements better match the application.
Is the TS3702IN suitable for battery-powered sensor conditioning?
Yes, the TS3702IN is suitable for battery-powered sensor conditioning because its typical current is only 9 µA per comparator. The 600 pA maximum input bias current also helps limit loading on high-impedance sensor signals. Actual battery life still depends on the divider resistance, reference current, output activity, and the duty cycle of the surrounding circuit. Confirm the input common-mode range and output behavior at the lowest operating supply voltage before deployment.
What is the best drop-in replacement for the TS3702IN?
The closest documented replacement candidates are the TS3702CN and TLC3702CP because both are dual micropower comparators in 8-pin through-hole packages. The TS3702CN retains the STMicroelectronics family, while TLC3702CP provides a cross-brand push-pull comparator option. Neither candidate should be treated as automatic in every design: verify pin polarity, input ranges, supply limits, timing, output levels, and temperature grade against the manufacturer datasheet before approving a substitution.
What can replace the TS3702IN on the same PCB?
A same-PCB replacement must use an 8-pin through-hole package and preserve the comparator channel assignments, input polarity, ground arrangement, and electrical limits. TS3702CN is the leading same-manufacturer candidate, and TLC3702CP is a cross-brand candidate described as a micropower dual push-pull comparator. Before replacing TS3702IN, compare the maximum supply voltage, input common-mode range, output levels, response time, input offset voltage, and operating-temperature specification from each manufacturer datasheet.
Is the TS3702IN the same as the TLC3702IP?
No, the TS3702IN and TLC3702IP are from different manufacturers and should not be assumed identical despite sharing the broad category of micropower dual comparators. The TS3702IN is an STMicroelectronics PDIP-8 device with specified 9 µA typical consumption per comparator, while TLC3702IP is a Texas Instruments device with its own ordering, temperature, and electrical limits. Use the TI TLC3702 datasheet and STMicroelectronics TS3702 datasheet for a manufacturer-by-manufacturer qualification.
Where can I buy the TS3702IN and what is its lead time?
Use the Request a Quote form on this page to ask for TS3702IN availability, current lead time, and an order quote. The manufacturer lists the TS3702 family as an active product, but production capacity and individual suffix availability can change. The requested configuration should identify the exact TS3702IN PDIP-8 MPN and any required tube, tray, or other approved packing method so the quotation matches the intended assembly process.
What is the price and stock status of the TS3702IN?
The current TS3702IN price and stock status should be requested through the Request a Quote form on this page. Availability for the exact PDIP-8 suffix depends on supplier inventory and scheduled manufacturer deliveries. Include the required quantity, target date, and packing preference with the request so the commercial response can reflect the intended order rather than a generic family-level quotation.

エンジニアリング参考データ: TS3702IN — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the TS3702IN for low-power, general-purpose dual threshold detection with push-pull CMOS outputs and an 8-pin PDIP footprint. Its 9 µA typical current per comparator, 600 pA maximum input bias current, 6.5 mV maximum offset voltage, and 1.5 µs maximum response time make it appropriate for battery-powered sensing and low-duty industrial monitoring. TS3702CN is the closest same-manufacturer candidate when its temperature grade and electrical limits match the design, while TLC3702CP and TLC3702IP are cross-brand candidates based on their micropower dual push-pull architecture. Before replacing the TS3702IN, verify the complete pin arrangement, input polarity, common-mode range, output levels, timing, maximum supply voltage, and operating-temperature grade. Do not use a cross-package comparator without PCB redesign, and do not assume that the lower current of another open-collector device offers the same interface or switching behavior.

代替品との比較

パラメータ この製品 TS3702CN TLC3702CP TLC3702IP
Brand STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments
Package PDIP-8 PDIP-8 PDIP-8 PDIP-8
Comparator Configuration Dual, 2 independent channels Dual comparator Dual comparator Dual comparator
Logic Technology CMOS CMOS LinCMOS LinCMOS
Output Type Push-pull CMOS Push-pull CMOS Push-pull Push-pull

主な差別化要因

  • Lower documented channel current within the same micropower comparator class (vs TLC3702CP)
  • Two independent channels with a defined maximum response time (vs TS3702CN)
  • Active push-pull output simplifies CMOS interfacing (vs TLC3702IP)

設計ノート

Do not treat the TS3702IN push-pull output like an open-collector output. STMicroelectronics specifies an active CMOS output stage, so an external pull-up resistor is normally unnecessary. More importantly, never connect the outputs of the two comparator channels together because push-pull drivers can source and sink current simultaneously. Confirm the logical combination of OUT1 and OUT2 in firmware or logic rather than tying the pins together.

Account for the complete always-on current, not just the comparator channels. The TS3702 consumes 9 µA typical per comparator, or approximately 18 µA for both channels, before divider and reference currents are included. Use high-value divider resistors to limit their own consumption, but verify that the resulting bias currents remain acceptable relative to the 600 pA maximum input bias specification. Confirm minimum and maximum supply conditions from the manufacturer datasheet.

Place the comparator close to the sensed node and keep the high-impedance input route short to reduce coupling from adjacent switching circuitry. Provide a solid ground return for both channels and decouple the supply pin locally where the device is used near a switching source. The available information does not specify the exact pin arrangement, so use the STMicroelectronics datasheet pin table when assigning tracks and do not infer positions from generic PDIP drawings.

Validate the input overdrive, output loading, and propagation delay in the actual circuit. The 6.5 mV maximum offset voltage and 1.5 µs maximum response time describe important comparison limits, but neither alone determines system accuracy. Use resistor values that keep inputs within the supported common-mode range and include the output rise time when driving long PCB traces or capacitive loads. The manufacturer datasheet is the controlling source for these conditions.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The manufacturer product page and datasheet establish the TS3702 family's function and electrical characteristics, but the available product information does not state the requested compliance statuses.

データ検証日: 2026-11-16 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

TS3702IN datasheet TS3702IN pinout TS3702IN datasheet pdf STMicroelectronics TS3702IN TS3702IN PDIP-8 comparator TS3702IN 9uA comparator TS3702IN response time TS3702IN equivalent TS3702IN replacement TS3702IN vs TLC3702CP TS3702IN battery powered sensor TS3702IN price TS3702IN stock where to buy TS3702IN

関連部品&用語

STMicroelectronics TS3702IN TS3702 TS3702CN TLC3702CP TLC3702IP Texas Instruments voltage comparator dual comparator analog comparator IC integrated circuit semiconductor CMOS LinCMOS push-pull output open-collector comparator PDIP-8 DIP-8 through-hole package surface-mount-compatible dual comparator 9 µA supply current 600 pA input bias current 6.5 mV input offset voltage 1.5 µs response time battery-powered threshold detection
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示