TS3702IN - Micropower Dual Comparator | STMicroelectronics
MPN: TS3702IN ✓ פעילTS3702IN סקירה
A voltage comparator is an analog mixed-signal component that compares two input voltages and produces a logic-level output indicating which input is higher. The TS3702IN belongs to the comparator hierarchy within integrated circuits and analog signal-conditioning ICs. Its micropower operating current makes it suitable for battery-powered equipment where continuous supply consumption must remain low, while its dual-channel configuration provides two comparison functions in one package.
The principal features are low power consumption, CMOS-compatible push-pull outputs, low input offset voltage, and a response time suitable for general-purpose signal detection. According to the STMicroelectronics TS3702 product page, the TS3702 consumes 9 µA typical per comparator, approximately twenty times less than a bipolar LM393. The 16 V maximum supply rating provides headroom for conventional 5 V and low-voltage industrial systems, while the 600 pA input bias current limits disturbance of high-impedance sensing nodes.
Internally, the device combines CMOS input stages with two independent comparator channels. The push-pull output architecture actively drives both logic states, making the outputs suitable for direct connection to compatible CMOS inputs. This differs from open-collector comparators, which require an external pull-up resistor and can present slower rising edges when additional capacitance must be charged. Board designers should still check the output timing and load limits in the manufacturer datasheet when driving unusually long traces or high-capacitance nodes.
Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, window comparators, and simple control loops. A second application is industrial sensing where low 9 µA typical current per comparator helps limit standby consumption. The TS3702IN can also supervise a divided supply rail by comparing its scaled voltage against a reference derived from another node.
The principal design consideration is logic compatibility. Push-pull outputs must not be tied together or connected to a pull-up resistor in the manner used with open-collector outputs. Input common-mode range, output voltage levels, and propagation-delay limits must be checked against the actual supply voltage and connected logic family before finalizing the circuit.
This product page combines the manufacturer specifications with package, sourcing, and replacement guidance for engineers evaluating the TS3702IN. It also identifies drop-in alternatives that retain the same 8-pin through-hole footprint, helping PCB designers compare functionality without introducing an unintended package migration.
חלופות תחליף ישיר עבור TS3702IN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TS3702IN (אותו גורם צורה וטביעת רגל) — שונים ב Comparator Type, Output Type, Package.
TS3702CN
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TLC3702CP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLC3702IP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TS3702IN דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | Dual general-purpose voltage comparator |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 16 V |
| Typical Supply Current | 9 µA per comparator |
| Input Offset Voltage | 6.5 mV maximum |
| Response Time | 1.5 µs maximum |
| Input Bias Current | 600 pA maximum |
| סוג פלט | Push-pull CMOS |
| Logic Technology | CMOS |
| Independent Comparators | 2 independent channels |
| מארז | PDIP-8, 8-pin through-hole |
| סוג הרכבה | Through-hole |
| Input Pin Count | 5 inputs, including 2 ground pins |
מדריך תצורת פינים של TS3702IN pdip-8, 8-pin through-hole
תצורת פינים עבור TS3702IN (מארזת pdip-8, 8-pin through-hole). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TS3702IN.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TS3702IN מתאים עבור 6 יישוםs: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Supply Overvoltage Monitoring, Window Comparator, Portable Medical Sensor Interface, Smart Home and IoT Limit Detection.
Battery-Powered Threshold Detection
The TS3702IN is well matched to battery-powered threshold detection because each comparator consumes 9 µA typical while providing a 1.5 µs maximum response time. Place one channel across a divided sensor or supply signal and the other across the corresponding threshold to create an alert or control output. The 600 pA maximum input bias current minimizes disturbance of high-impedance dividers, while push-pull outputs drive compatible CMOS logic without a pull-up resistor. Check the common-mode input range at the minimum battery voltage before finalizing the thresholds.
מומלץ
Industrial Sensor Signal Conditioning
The TS3702IN can condition weak or offset industrial sensor signals with its dual independent comparator channels and 600 pA maximum input bias current. One channel can compare the sensor output with an adjustable threshold, while the other can monitor an alarm or fault condition. The 6.5 mV maximum offset specification helps define the comparison uncertainty around a small signal, and the 1.5 µs maximum response time supports prompt logic decisions. The push-pull output simplifies interfacing with compatible control logic, although the input common-mode range must cover the sensor’s operating voltage.
מומלץ
Supply Overvoltage Monitoring
Use the TS3702IN as a low-power supply supervisor when a monitored rail must be compared with a scaled reference. Two independent channels permit separate overvoltage and undervoltage decisions, creating a window-comparator function without two separate ICs. The 16 V maximum supply rating provides useful headroom around conventional low-voltage rails, and the 9 µA typical consumption per comparator limits continuous monitoring overhead. Divider resistance must balance reference accuracy against leakage, while the comparator input common-mode range and output levels must be checked at startup and fault conditions.
מומלץ
Window Comparator
The two independent TS3702IN channels can form a window comparator in which one output indicates an above-limit condition and the other indicates a below-limit condition. This arrangement is useful for battery packs, signal ranges, and adjustable set points that must remain between two boundaries. With a 1.5 µs maximum response time and 6.5 mV maximum input offset voltage, the device can provide fast general-purpose threshold decisions. Logic combining should account for output polarity, and both channels must remain inside their valid input common-mode range during every monitored transition.
מומלץ
Portable Medical Sensor Interface
The TS3702IN can support threshold decisions around portable medical-sensor signals where continuous comparator current must remain low. Its 9 µA typical consumption per channel and 600 pA maximum input bias current help preserve weak sensor signals and reduce energy use. The dual arrangement can monitor a physiological signal boundary or compare a sensor-derived value with a reference level. For medical equipment, the complete signal chain must satisfy the applicable system quality and safety requirements; use the manufacturer datasheet to verify electrical limits and qualify the finished design independently of the comparator.
מומלץ
Smart Home and IoT Limit Detection
The TS3702IN fits IoT and smart-home modules that need continuous limit detection without the higher standby current of a bipolar comparator. One channel can identify a sensor threshold crossing, while the other can supervise a divided local supply. The push-pull outputs can connect directly to compatible CMOS logic, avoiding the external pull-up resistor required by open-collector implementations. The 600 pA maximum input bias current is advantageous for high-impedance sensing networks, but divider leakage, the supported input voltage range, and the module’s sleep strategy should be evaluated together for long battery life.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TS3702IN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TS3702CN | TLC3702CP | TLC3702IP |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Comparator Configuration | Dual, 2 independent channels | Dual comparator | Dual comparator | Dual comparator |
| Logic Technology | CMOS | CMOS | LinCMOS | LinCMOS |
| Output Type | Push-pull CMOS | Push-pull CMOS | Push-pull | Push-pull |
מבדילים עיקריים
- Lower documented channel current within the same micropower comparator class (לעומתTLC3702CP)
- Two independent channels with a defined maximum response time (לעומתTS3702CN)
- Active push-pull output simplifies CMOS interfacing (לעומתTLC3702IP)
הערות תכנון
Do not treat the TS3702IN push-pull output like an open-collector output. STMicroelectronics specifies an active CMOS output stage, so an external pull-up resistor is normally unnecessary. More importantly, never connect the outputs of the two comparator channels together because push-pull drivers can source and sink current simultaneously. Confirm the logical combination of OUT1 and OUT2 in firmware or logic rather than tying the pins together.
Account for the complete always-on current, not just the comparator channels. The TS3702 consumes 9 µA typical per comparator, or approximately 18 µA for both channels, before divider and reference currents are included. Use high-value divider resistors to limit their own consumption, but verify that the resulting bias currents remain acceptable relative to the 600 pA maximum input bias specification. Confirm minimum and maximum supply conditions from the manufacturer datasheet.
Place the comparator close to the sensed node and keep the high-impedance input route short to reduce coupling from adjacent switching circuitry. Provide a solid ground return for both channels and decouple the supply pin locally where the device is used near a switching source. The available information does not specify the exact pin arrangement, so use the STMicroelectronics datasheet pin table when assigning tracks and do not infer positions from generic PDIP drawings.
Validate the input overdrive, output loading, and propagation delay in the actual circuit. The 6.5 mV maximum offset voltage and 1.5 µs maximum response time describe important comparison limits, but neither alone determines system accuracy. Use resistor values that keep inputs within the supported common-mode range and include the output rise time when driving long PCB traces or capacitive loads. The manufacturer datasheet is the controlling source for these conditions.
מידע על תאימות
The manufacturer product page and datasheet establish the TS3702 family's function and electrical characteristics, but the available product information does not state the requested compliance statuses.