XMC4500F144K768ACXQMA1 - 120MHz Cortex-M4 MCU | Infineon
部品番号: XMC4500F144K768ACXQMA1 ✓ 生産中XMC4500F144K768ACXQMA1 概要
A microcontroller is a programmable semiconductor that integrates a processor core, memory, communication peripherals, timers, analog interfaces, and control logic onto one package. The XMC4500 architecture belongs to the hierarchy of embedded processors: ARM Cortex-M4 core, 32-bit microcontroller, XMC4000 family, and industrial embedded control. Its combination of performance and peripheral integration helps reduce the component count in motor-control, communications, and industrial automation systems.
Key features include a 120 MHz Cortex-M4 processor, 768 KB of flash storage, 160 KB of RAM, 32-bit processing, and communication functions identified in the product information, including CAN, LIN, and Ethernet. The mixed-signal acquisition capability supports applications where analog measurement and digital control must operate in the same embedded platform. The industrial-grade ordering designation is associated with the XMC4500-F144K768-AC family.
The device uses an industry-standard ARM Cortex-M4 processor core and a configurable peripheral set intended for energy-efficient industrial applications. At 120 MHz, it provides substantially greater computation headroom than slower general-purpose microcontrollers, while the integrated communications and analog resources reduce the need for separate interface devices. Designers should still verify peripheral availability, pin multiplexing, electrical limits, and package details against the Infineon XMC4500 datasheet before finalizing a PCB.
Typical applications include industrial motor control, CAN and LIN network nodes, Ethernet-connected automation equipment, factory sensor hubs, power conversion controllers, and embedded industrial gateways. The XMC4500 is particularly appropriate when local control, communications, and analog acquisition are required in a single controller rather than across multiple discrete devices.
The primary design consideration is package and pin planning. The 144-pin LQFP footprint requires a land pattern matching the PG-LQFP-144-13 package, careful escape routing, and adequate decoupling near the supply pins. Engineers should also review clock configuration, communication peripheral multiplexing, and the recommended operating ranges in the manufacturer datasheet before production release.
This page combines the manufacturer datasheet, distributor product listings, package information, and engineering-oriented application guidance to make the XMC4500F144K768ACXQMA1 easier to evaluate for industrial embedded designs. The exact ordering information, electrical characteristics, lifecycle status, and peripheral configuration should be confirmed against the current Infineon documentation before procurement.
ドロップイン代替品: XMC4500F144K768ACXQMA1 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
XMC4500-F144K768-AC
✅ ドロップイン📋 参考代替品(カタログ未掲載)
XMC4500-F144F768-AC
✅ ドロップイン📋 参考代替品(カタログ未掲載)
XMC4500F144K768ACXQMA1 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M4 microcontroller |
| Series | XMC4000 |
| Processor Core | ARM Cortex-M4 |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 768 KB (768K x 8) |
| RAM | 160 KB |
| Architecture | 32-bit |
| パッケージ | PG-LQFP-144-13 |
| ピン数 | 144 pins |
| Mixed-Signal Acquisition | Supported |
| CAN Interface | Supported |
| LIN Interface | Supported |
| Ethernet Connectivity | Supported |
| Product Family | XMC4500 |
| Ordering Designation | XMC4500-F144K768-AC |
| Duty/Grade Designation | Industrial |
| 実装タイプ | Surface mount |
XMC4500F144K768ACXQMA1 pg-lqfp-144-13 ピン配置ガイド
XMC4500F144K768ACXQMA1 (pg-lqfp-144-13 パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: XMC4500F144K768ACXQMA1.
詳細は データシート をご参照ください。
主な用途
XMC4500F144K768ACXQMA1 の用途: 6 件s: Industrial Motor Control, CAN Networked Automation Node, Ethernet-Connected Industrial Gateway, Factory Sensor and Actuator Hub, Power Conversion Controller, Industrial Communication Controller.
Industrial Motor Control
The XMC4500F144K768ACXQMA1 fits industrial motor-control platforms because its 120 MHz ARM Cortex-M4 core supports deterministic control-loop processing while the 768 KB flash and 160 KB RAM accommodate control algorithms, diagnostics, and communication stacks. Mixed-signal acquisition allows current, voltage, and position-related signals to be handled close to the control logic. CAN and LIN connectivity can connect the controller to modules and service diagnostics. Before schematic capture, confirm the required PWM channels, ADC inputs, timers, encoder interfaces, and pin multiplexing in the Infineon datasheet, and validate the thermal design against the selected operating range.
おすすめ
CAN Networked Automation Node
The XMC4500F144K768ACXQMA1 is suitable for an industrial CAN node that must combine protocol handling with local acquisition and control. Its 120 MHz Cortex-M4 processor provides processing headroom for CAN frames, application logic, diagnostics, and nonblocking communications tasks. The 160 KB RAM supports communication buffers and working state, while 768 KB flash accommodates firmware, calibration data, and update logic. The integrated CAN and LIN functions reduce external interface requirements. Use the datasheet to select the correct peripheral instance and pins, and configure termination, protection, grounding, and bus levels for the target network.
おすすめ
Ethernet-Connected Industrial Gateway
The XMC4500F144K768ACXQMA1 can serve as the control processor in an Ethernet-connected industrial gateway when local real-time functions must coexist with higher-level communications. The 120 MHz Cortex-M4 core processes protocol stacks and gateway logic, and the 768 KB flash provides room for firmware components. CAN and LIN interfaces allow the gateway to bridge multiple field buses, while mixed-signal acquisition can monitor local process signals. The exact Ethernet PHY, isolation, magnetics, and connector implementation remain external to the MCU. Confirm supported MAC and Ethernet pin options, reference-clock requirements, and packet-buffer configuration in the manufacturer documentation.
おすすめ
Factory Sensor and Actuator Hub
The XMC4500F144K768ACXQMA1 fits a factory sensor hub that must aggregate mixed-signal measurements and distribute control commands across a network. Its 160 KB RAM can hold acquisition buffers, calibration tables, and communication state, while the 768 KB flash supports sensor drivers, filtering, diagnostics, and field-bus protocols. The 120 MHz processing rate supports responsive sampling and filtering, and CAN or LIN connectivity can simplify wiring to distributed actuators. Engineers should verify the ADC resolution, sampling characteristics, channel multiplexing, and conversion timing in the datasheet, and isolate sensitive analog inputs appropriately from switching and high-current stages.
おすすめ
Power Conversion Controller
The XMC4500F144K768ACXQMA1 is applicable to sophisticated industrial power-conversion control where fast computation, mixed-signal feedback, and network management are required. Its 120 MHz Cortex-M4 performance supports loop calculations, protection logic, supervisory tasks, and communications, while the mixed-signal acquisition resources can monitor converter voltages and currents. CAN or LIN communication can expose operating data and accept configuration commands. The MCU is a controller rather than a dedicated power converter, so external power stages, gate drivers, sensing networks, and protection hardware determine the final design. Verify timer accuracy, comparator and ADC resources, startup behavior, and control-loop timing against the datasheet.
おすすめ
Industrial Communication Controller
The XMC4500F144K768ACXQMA1 supports industrial communication-controller designs built around CAN, LIN, and Ethernet connectivity. The 32-bit Cortex-M4 core at 120 MHz handles protocol processing, routing, diagnostics, and application functions, while 768 KB flash and 160 KB RAM provide resources for a multitask firmware architecture. Multiple communication standards allow one controller to coordinate otherwise separate network segments. Engineers must assign alternate-function pins without conflicts, ensure adequate timing margin at the selected communication rates, and separate communications transceivers from the MCU supply and ground domains as appropriate. The datasheet and reference manual should govern final peripheral, interrupt, and pin assignments.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: XMC4500F144K768ACXQMA1 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | XMC4500-F144K768-AC | XMC4500-F144F768-AC |
|---|---|---|---|
| Package | PG-LQFP-144-13 | PG-LQFP-144-13 | PG-LQFP-144-13 |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Processor Core | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 |
| Maximum CPU Frequency | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 768 KB | 768 KB | 768 KB |
| Ethernet Connectivity | Supported | Supported | Supported |
| Ordering Characteristic | K768 with XQMA1 suffix | K768 base designation | F768 designation |
主な差別化要因
- Exact full ordering-code identity (vs XMC4500-F144K768-AC)
- 120 MHz Cortex-M4 performance (vs XMC4500-F144F768-AC)
- Integrated industrial connectivity (vs XMC4500-F144K768-AC)
設計ノート
Use the PG-LQFP-144-13 land pattern and verify pad dimensions against the Infineon package drawing before releasing artwork. Place input and output decoupling capacitors close to their assigned supply and ground pins, provide a low-impedance return path beneath the device where the layout rules permit, and route high-current or fast-switching nets away from analog inputs. Confirm every pin's reset, clock, debug, and alternate-function role using the datasheet pin table rather than assigning functions by position alone.
Separate analog acquisition circuitry from Ethernet, CAN, LIN, and switching-supply regions. Maintain short, guarded analog traces, use a clear return reference, and place analog filtering components close to the controller pins. For communications interfaces, follow the recommended external transceiver, termination, protection, and grounding topology in the relevant interface guidance. The mixed-signal performance of the design depends as much on trace geometry and return-current control as on the nominal ADC resources.
Do not substitute the base XMC4500-F144K768-AC designation or the related F768 ordering code solely from the visible core, flash, and package descriptions. Before replacement, compare flash organization, temperature grade, package, peripheral set, pin multiplexing, and lifecycle status in the Infineon ordering information. Also verify startup, clock, watchdog, and pin-reset requirements; a device can share the same package while using meaningfully different ordering characteristics.
コンプライアンス情報
The available product information identifies an industrial XMC4500 microcontroller but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the stated industrial rather than automotive ordering designation.