증폭기 IC
제품 (497)
SI8921BD-IS4 - ±250 mV Isolated Amplifier, 5 kV | Skyworks
The Skyworks Solutions SI8921BD-IS4 is a galvanically isolated analog amplifier with a ±250 mV differential input range, 5.0 kV RMS isolation rating, and differential output, housed in a wide-body stretched SOIC-8 package. Key headline specifications include 0.8 µs signal delay, ±0.40 µV typical input offset, ±0.06% typical gain error, 0.5 µV/°C offset drift, and -9 ppm/°C typical gain drift, providing accurate current-shunt measurement across industrial temperature ranges. An isolated amplifier is a type of analog amplifier that combines a precision front-end differential amplifier with a galvanic isolation barrier, transferring the signal across the barrier through capacitive or transformer coupling. The isolation barrier protects low-voltage control circuitry from high-voltage common-mode transients on the field side, enabling safe measurement of floating signals such as those present across current-shunt resistors in motor drives, solar inverters, and uninterruptible power supplies. Within the broader hierarchy, an isolated amplifier belongs to the isolation IC family, which includes digital isolators and isolated gate drivers - all of which form essential building blocks in power-management and industrial-automation systems requiring reinforced insulation per IEC 60747-17 and UL 1577. The SI8921BD-IS4 features a specified input range of ±250 mV, well suited for direct connection across low-ohm shunt resistors in high-current paths. Its differential output swings to a 2.5 V peak full-scale signal, which can be fed directly into the ADC front-end of a motor controller or power-conversion MCU. The device's low offset and drift specifications eliminate the need for periodic calibration in many systems, while its 0.8 µs propagation delay supports closed-loop current control in fast-switching converters. Architecturally, the SI8921BD-IS4 integrates a precision chopper-stabilized input amplifier, a sigma-delta modulator, an isolation capacitor barrier, and a differential output decoder on the low-voltage side. The internal LDO regulators on both sides of the barrier simplify power-supply design - the high-side is powered from a 3.0 V to 5.5 V supply, and the low-side is powered independently from 3.0 V to 5.5 V. The CMOS output stage is capable of driving 2 kΩ loads with low distortion. Typical applications include current-shunt monitoring in three-phase motor drives, photovoltaic inverter string-current sensing, UPS battery-current measurement, industrial process-control isolation, and high-voltage rail monitoring in telecom rectifiers. The differential output interfaces directly with SAR ADCs and sigma-delta converters found in C2000 and PIC32 families. When designing with this device, place bypass capacitors of 0.1 µF and 1 µF close to both VDDA and VDDD pins, keep the input traces short and balanced to preserve CMRR, and observe the creepage and clearance rules of the wide-body SOIC-8 footprint to maintain the 5 kV isolation rating. The differential output should be routed as a matched pair to avoid common-mode pickup in noisy switching environments. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer product page or distributor listing.
SSM2141PZ - Differential Line Receiver, 100dB CMR, 3MHz | ADI
The Analog Devices SSM2141PZ is an integrated differential line receiver (audio amplifier, Class AB) designed to receive balanced line inputs in professional audio applications requiring high noise immunity and optimum common-mode rejection. Housed in an 8-pin PDIP (PZ) package, it operates from dual supplies of ±6V to ±18V and typically achieves 100 dB of common-mode rejection (CMR) at DC and 60 Hz, far exceeding the ~40 dB CMR achievable with a generic op amp and four discrete precision resistors. The device delivers 0.001% typical THD, a fast 10 V/us slew rate, and a wide 3 MHz small-signal bandwidth. A balanced line receiver is a specialized analog building block that accepts a differential signal riding on a common-mode voltage (such as the long cable run from a stage to a mixing console) and converts it to a single-ended, ground-referenced output while rejecting the common-mode noise picked up along the way. In the audio signal chain hierarchy, the SSM2141 sits between the input connector / XLR stage and downstream ADC or line-level processing; it is part of the broader family of audio amplifiers and instrumentation amplifiers used in pro-audio and broadcast equipment. Key differentiating specifications include 100 dB CMR (DC, typ), 70 dB CMR at 20 kHz and 62 dB at 40 kHz, 0.001% THD+N, 10 V/us slew rate, 3 MHz bandwidth, and a 600 ohm minimum load. Internal thin-film resistor networks are laser-trimmed to deliver matching that no off-the-shelf 0.1% discrete resistor approach can match at production volume, which is what enables the headline CMR figure. Typical applications include balanced audio line receivers in mixing consoles and stage boxes, AES3 / EBU receiver front-ends, audio distribution amplifiers, and instrumentation front-ends where high DC and AC common-mode rejection is required. The 600 ohm load rating and +22 dBu headroom make it directly compatible with broadcast and studio analog line-level standards. When designing with the SSM2141PZ, treat the gain-setting resistor (typically 10 kohm between pins 1 and 8 for unity gain) as a low-noise, low-drift metal-film part to preserve CMR. Add 100 ohm series output resistors plus 10 nF to ground at each output if cable capacitance will exceed ~1000 pF, to prevent oscillation. Decouple both supply pins with 0.1 uF ceramic in parallel with 10 uF tantalum or electrolytic, placed within 5 mm of the package. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB layout notes not found in the manufacturer datasheet alone, including cross-brand substitutes from Texas Instruments and Maxim that share the same 8-pin PDIP footprint and equivalent CMR-class performance.
SSM2142 - Balanced Audio Line Driver, 10 Vrms/600Ω | Analog Devices
The Analog Devices SSM2142 is an integrated differential-output buffer amplifier that converts a single-ended input signal to a balanced (differential) output pair with high output drive capability. Housed in a 16-pin SOIC (or PDIP variant) package, it delivers a transformer-like balanced output capable of driving 10 V RMS into a 600 Ω load, making it a single-chip replacement for discrete audio line-driver circuits that historically required audio output transformers. A balanced line driver, or differential-output audio amplifier, is a specialized analog IC that takes an unbalanced single-ended input and produces two anti-phase outputs whose common-mode noise is rejected by the downstream differential receiver. The SSM2142 belongs to the audio amplifier IC category and sits inside the broader signal-chain taxonomy of op-amps / buffers → line drivers → audio interface ICs → mixed-signal semiconductors. By generating a true differential signal on-chip, it eliminates the need for bulky, expensive audio output transformers while preserving the common-mode rejection benefits that transformers provided in professional audio. Key features include a transformer-like balanced output, 10 V RMS drive capability into 600 Ω, low distortion suitable for professional audio distribution, and excellent common-mode rejection when paired with the complementary SSM2141 receiver. The 16-pin SOIC footprint is industry-standard, allowing direct PCB integration into existing professional audio designs without layout rework. The differential architecture also improves immunity to ground loops when running audio over long cable runs in studio, broadcast, and stage environments. The SSM2142 uses internal thin-film resistor networks laser-trimmed during production to achieve tight gain matching between the positive and negative output legs, which directly determines how well the common-mode noise of the line is rejected by the paired receiver. This integrated matched-resistor approach eliminates manual trimming and provides stable performance over temperature. The amplifier can drive the full pro-audio level of +24 dBu (12.28 V RMS) into balanced loads when powered from appropriately split ±V rails, while still operating cleanly from standard ±15 V laboratory supplies. Typical applications include balanced audio line drivers for pro-audio mixing consoles, broadcast studio and stage equipment, audio interfaces with XLR outputs, and differential signal transmission across factory-floor instrumentation lines where ground isolation is critical. The datasheet also documents its use in pairs (SSM2142 transmitter with SSM2141 receiver) over long cable runs. When designing with the SSM2142, pay attention to power-supply decoupling (low-ESR caps at both ±V pins are mandatory for low distortion) and to the recommended external feedback network that sets the closed-loop gain. PCB layout should keep the input trace short and symmetrical, since mismatched routing directly degrades the common-mode rejection performance measured at the receiver end.
SSM2143PZ - Audio Differential Line Receiver, 90dB CMR | Analog Devices
The Analog Devices SSM2143PZ is an integrated differential amplifier (line receiver) intended to receive balanced audio line inputs in professional and prosumer audio applications requiring high common-mode noise immunity. Housed in an 8-pin PDIP (PZ) through-hole package, it is specified for a typical common-mode rejection of 90 dB at DC and 60 Hz, dropping to 85 dB at 20 kHz, achieved by laser-trimming on-chip resistors to better than 0.005%. An audio line receiver is the front-end gain stage that converts a balanced, twisted-pair analog signal — typically carried on XLR or TRS cable runs — into a single-ended ground-referenced signal that downstream ADC, mixing, or amplifier stages can use. Its defining role is rejecting common-mode noise (mains hum, RF pickup, ground-loop voltage) that appears equally on both signal lines while preserving the differential audio content. Receivers such as the SSM2143PZ therefore sit at the top of the analog signal-path hierarchy: transducer -> line receiver -> ADC/mixer -> power amplifier -> speaker. Key features include an ultra-low total harmonic distortion of 0.0006% typical at 1 kHz (less than 0.004% across the full audio band), a fast 10 V/us slew rate, and a wide 7 MHz small-signal bandwidth. The device operates from dual supplies of ±6 V to ±18 V (single supply 6 V to 36 V) and draws only 2.7 mA quiescent supply current. The input stage handles signals as large as +28 dBu at the nominal G = 1/2 configuration, allowing direct connection to professional +4 dBu consoles without external attenuation. Although optimized for G = 1/2, a gain of 2 is realized by reversing the +IN/-IN and SENSE/REFERENCE connections. The SSM2143 architecture combines a precision operational front-end with four on-chip laser-trimmed thin-film resistors that set the gain and provide the matched impedance ratio required for high CMR. Internal overdrive clamping protects downstream stages when large common-mode or differential transients appear on the line, eliminating the need for external protection diodes in most studio and stage installations. Typical applications include balanced audio line receivers in mixing consoles, microphone preamplifier inputs, A/D converter driver stages in audio digitizers, broadcast and recording-studio equipment, and stage-box interfaces for live sound. Its high CMR also makes it well suited to industrial instrumentation where long cables carry small analog signals in electrically noisy environments. When designing with the SSM2143PZ, route input traces as a tightly coupled, length-matched pair and place 0.1 uF supply-decoupling capacitors within 5 mm of the supply pins. The device is specified for operation from -40 C to +85 C and remains RoHS-compliant; the SOIC-8 (S) variant should be selected for reflow-compatible SMT designs. This page synthesizes distributor pricing, parametric cross-references, and PCB-level design guidance for the SSM2143PZ beyond what the manufacturer datasheet alone provides.
SSM2166SZ - Microphone Preamplifier w/ Variable Compression | ADI
The Analog Devices SSM2166SZ is a complete microphone conditioner IC that integrates a low-noise microphone preamplifier, a voltage-controlled amplifier (VCA), and a variable compression/noise-gate control loop in a single 14-pin narrow-body SOIC (NSOIC) package. The part provides a unity-gain microphone preamp front-end with adjustable gain followed by a dynamic compression block whose compression ratio and rotation point are user-programmable via external resistors, plus an adjustable-threshold noise gate that mutes the output below a settable floor to suppress ambient hum and breath noise. A microphone preamplifier with variable compression and noise gating is a specialized audio signal-chain block used to capture speech or instrument signals with wide dynamic range and deliver them at a controlled level to downstream ADCs, codecs, mixers, or transmitters. Within the system hierarchy, the SSM2166SZ sits in the analog front-end path between the electret or condenser microphone capsule and the next stage (codec, DSP, mixer, or modulator), and belongs to the broader category of audio amplifiers → amplifier ICs → integrated circuits. By combining three traditionally discrete blocks (mic preamp, AGC/compressor, noise gate) into one IC, it eliminates the need for an external detector op-amp, envelope rectifier, and VCA, reducing board area and design complexity. Key specifications of the SSM2166SZ include a low input-referred noise voltage that supports high signal-to-noise ratio microphone capture, an adjustable compression ratio from approximately 1:1 to over 10:1, a variable rotation point, a user-settable noise-gate threshold, an internal voltage reference for biasing, and an analog supply range suited to typical 5V audio subsystems. According to the Analog Devices SSM2166 datasheet, the device operates over the extended industrial temperature range of -40C to +85C and is supplied in a 14-lead SOIC package rated for surface-mount assembly. The compression loop is built around a low-noise VCA whose gain is dynamically adjusted by an envelope detector tracking the output level, producing a closed-loop AGC characteristic that prevents downstream stages from clipping on loud sounds while keeping quiet passages above the noise floor. Designers set the rotation point (the level at which compression begins), the compression ratio (how aggressively loud signals are attenuated), and the gate threshold (the level below which output is muted) using external resistor dividers, giving the SSM2166SZ rare flexibility in a single package. Typical applications include computer audio microphone inputs, voice-over-IP headsets, communications and public-address systems, intercoms, two-way radio audio conditioning, and consumer voice-recognition front-ends where consistent speech level is critical to recognition accuracy. It also serves broadcast and conferencing equipment that requires uniform levels across multiple talkers. When designing with this part, pay attention to the gain-setting resistor values around the preamp and VCA stages, place the decoupling capacitor as close as possible to the supply pin, and follow Analog Devices' reference layout guidance to preserve the device's signal-to-noise ratio. Choice of rotation point and compression ratio directly affects intelligibility and naturalness of the captured voice. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, with cross-references verified against the latest DigiKey and Mouser listings as of 2026-10-10.
STK443 - 2Ch 5-25W AF Power Amp Hybrid IC | SANYO
The SANYO STK443 is a 2-channel (stereo) audio-frequency power amplifier built as a thick-film hybrid integrated circuit, delivering 5 W to 25 W minimum per channel into typical loudspeaker loads. It is supplied in a single inline SIP package with 10 formed leads, designed to be mounted through-hole on the amplifier PCB alongside its own heatsink tab. The STK443 was developed for low-cost split-supply consumer audio products where a compact, self-contained output stage simplifies board layout versus discrete complementary-pair designs. An AF (audio-frequency) power amplifier is the final active stage in an audio reproduction chain that drives a loudspeaker from a low-level signal source such as a preamplifier, mixer, or DAC output. Hybrid AF power ICs integrate input and driver transistors, output power devices, and biasing components on a single ceramic substrate, distinguishing them from monolithic silicon audio ICs by their higher output power, higher supply voltage tolerance, and larger physical footprint. Within the broader component taxonomy, the STK443 belongs to the amplifier IC category, which itself is a subset of analog signal-chain ICs and ultimately of power management and signal-conditioning semiconductors. The STK443 features a typical output of 2 x 25 W at low THD into a defined load impedance, operates over a wide supply range, and includes internal thermal protection. The dual-channel monolithic front end is followed by discrete power transistors mounted on the same substrate, a topology that lets the device source peak current demands while remaining economically viable for mass-produced stereo equipment. Built-in short-circuit and over-temperature shutdown protect the output stage against common fault conditions seen in consumer amplifiers. Typical applications for the STK443 include home stereo amplifiers, integrated A/V receivers, karaoke mixing amplifiers, powered speaker systems, and musical instrument practice amplifiers. It is also found in automotive head-unit audio outputs and as a retrofit replacement module in legacy SANYO-designed equipment where the original STK-series hybrid has failed and a same-form-factor part is required to avoid PCB rework. When designing with the STK443, observe the recommended heatsink thermal resistance and mounting torque to keep the substrate within its rated junction temperature under sustained full-power operation. Bypass supplies close to the module's VCC pins and use the recommended Zobel RC network across each output to maintain stability with reactive speaker loads. This page synthesizes distributor availability, parametric drop-in alternatives, and practical design notes gathered from SANYO documents and aftermarket datasheets not typically aggregated by catalog distributors.
SY88803VKG - 155Mbps PECL Limiting Post Amplifier | Microchip
The Microchip Technology (formerly Micrel) SY88803VKG is a 3.3V/5V, 155Mbps PECL low-power limiting post amplifier with a TTL Loss-of-Signal (LOS) output, housed in a 10-pin MSOP package. It is designed specifically for fiber-optic receiver front ends that follow a transimpedance amplifier (TIA). A limiting post amplifier is the second stage in an optical receiver signal chain. The linear signal output from a TIA can contain significant amounts of noise and may vary widely in amplitude; a limiting amplifier converts this small, noisy differential signal into a clean, fixed-amplitude logic-level PECL data stream, restoring signal integrity before clock-and-data-recovery (CDR) circuitry. In the hierarchy of optical receiver electronics, it sits between the TIA and the CDR/serializer, and is a form of special-purpose high-speed amplifier IC. Key features include single 3.3V or 5V supply operation to 155Mbps, low-noise PECL differential data outputs, a chatter-free TTL Loss-of-Signal output, a TTL /EN enable input for power management, and a programmable LOS assertion threshold. Low power consumption suits compact optical modules such as OC-3/STM-1 and Fast Ethernet transceivers. Architecturally, the device uses a cascade of wideband differential gain stages with automatic offset compensation; the saturating output stages guarantee constant output swing regardless of input amplitude above sensitivity. The programmable LOS threshold lets designers match the trip point to the optical module sensitivity budget, and the chatter-free hysteresis design prevents false LOS toggling near threshold. Typical applications include 155Mbps fiber-optic receivers, SDH/SONET OC-3 line cards, Fast Ethernet (100Base-FX) optical modules, and industrial fiber links. It connects directly to typical TIAs, making it a drop-in signal-chain element. Design consideration: route the differential PECL outputs as 50-ohm controlled-impedance pairs and decouple the supply pins close to the package to keep jitter low; verify the LOS threshold setting against the TIA output amplitude range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TAS5827 - 47W Stereo Closed-Loop Class-D Amp | TI
The TAS5827 is a stereo high-performance, closed-loop Class-D audio amplifier with an integrated audio processor and support for up to 192-kHz audio. It delivers 47W per channel in BTL mode and is housed in a 32-pin VQFN (5x5 mm) package. The device features a digital input interface, making it ideal for modern digital audio systems. A Class-D amplifier is a switching amplifier that uses pulse-width modulation to achieve high efficiency, often exceeding 90%, compared to linear amplifiers. It is a key component in the audio signal chain, converting digital audio data into high-power analog output while minimizing heat dissipation. The TAS5827 integrates a closed-loop architecture, which improves linearity and reduces distortion, and an audio processor for advanced signal processing. Key features include a delay buffer up to 5ms in BTL mode or 10ms in PBTL mode, Class-H control for enhanced efficiency, and hardware control mode for selecting switching frequency, analog gain, BTL/PBTL mode, and cycle-by-cycle current limit threshold via pin configuration. The device also supports software control mode with classic BQs, 3-band DRC, AGL, and proprietary audio envelope tracking Class-H control. The TAS5827 uses a closed-loop feedback design that reduces power supply noise and improves audio quality. It integrates a high-performance audio processor capable of executing complex DSP algorithms, making it suitable for applications requiring EQ, DRC, and dynamic range compression. The device operates from a single supply and includes comprehensive protection features. Typical applications include smart speakers, soundbars, home theater systems, and active speakers. Its high efficiency and low power dissipation make it ideal for battery-powered and energy-conscious designs. The integrated audio processor reduces external component count, simplifying system design. When designing with the TAS5827, ensure proper PCB layout for thermal management and minimize parasitic inductance in the output stage. Use appropriate decoupling capacitors on the power supply pins and follow the recommended layout in the datasheet for optimal performance.
TAS5827RHBR - 43W Stereo Digital Class-D Amp | Texas Instruments
The Texas Instruments TAS5827RHBR is a 43-W stereo, digital-input, closed-loop Class-D audio amplifier with integrated audio processing and Class-H control. Housed in a 32-pin VQFN (RHB) package measuring 5x5 mm, this device delivers high-efficiency amplification for a wide range of consumer and professional audio applications. It supports a supply voltage range of 4.5V to 26.4V and operates over a temperature range of -40°C to 85°C. A Class-D amplifier is a switching amplifier that uses pulse-width modulation (PWM) to achieve high efficiency, often exceeding 90%, compared to linear amplifiers. The TAS5827 integrates a closed-loop architecture that reduces distortion and improves power supply rejection, making it suitable for high-fidelity audio systems. The digital input interface accepts I2S, TDM, and other digital audio formats, simplifying system design by eliminating the need for external DACs. Key features include a 43-W output power per channel into 4-ohm loads, integrated audio processor with biquad filters and dynamic range compression, and Class-H control that optimizes power supply voltage for efficiency. The device also supports multiple switching frequencies and offers cycle-by-cycle current limit protection. Its closed-loop design ensures low THD+N and high signal-to-noise ratio, critical for premium audio performance. The TAS5827 uses a digital audio processing core that can be configured via I2C or hardware control mode. In hardware mode, switching frequency, analog gain, BTL/PBTL mode, and current limit threshold are set via pins, eliminating the need for software driver integration. This flexibility makes it easy to deploy in systems where firmware development is not desired. Typical applications include smart speakers, soundbars, home theater systems, and automotive audio. The high efficiency reduces heat dissipation, enabling compact designs without large heatsinks. The integrated audio processor allows designers to implement EQ, crossover, and dynamic range control without external DSP. When designing with this device, ensure proper PCB layout with adequate ground planes and decoupling capacitors near the power pins. The thermal pad must be soldered to a copper area for heat dissipation. Also, consider the input signal format and configure the device accordingly for optimal performance.
TAS6754QDKQRQ1 - Automotive 4-Ch Class-D Audio Amp | TI
The TAS6754QDKQRQ1 is an automotive-grade, four-channel digital-input Class-D audio amplifier from Texas Instruments, offered in a 56-pin HSSOP (DKQ) package with exposed thermal pad. It implements 1L modulation, requiring only one inductor per BTL channel, and operates from a 19V supply with a 2MHz switching frequency. The device integrates current sense and real-time DC/AC load diagnostics for robust automotive speaker fault detection. A Class-D audio amplifier is a switching amplifier that converts a digital or analog audio signal into a high-frequency pulse-width modulated square wave, which is then low-pass filtered to reconstruct the audio. Class-D topologies achieve high efficiency (typically 80-90%) because the output transistors operate as switches, minimizing power dissipation compared to linear Class-AB amplifiers. In automotive audio systems, this efficiency reduces heat-sinking requirements and extends the available audio power from the vehicle's electrical system. Key features include four independent audio channels, 1L modulation that removes four inductors versus traditional designs, 2MHz switching for compact output filters, integrated current sense, and DC/AC real-time load diagnostics. The 19V rated supply is aligned with automotive audio power rails, and the AEC-Q100 Q1 suffix qualifies the device for automotive applications. The 56-pin HSSOP package supports surface-mount assembly with an exposed thermal pad for heat removal. 1L modulation is a proprietary Class-D scheme that uses a single inductor per bridge-tied-load channel, reducing system cost and size. The 2MHz switching rate moves the switching fundamental well above the audio band, simplifying the output low-pass filter and lowering out-of-band emissions. Integrated current sense and real-time load diagnostics monitor speaker health, enabling fault detection for shorts, opens, and degradation. The digital input accepts common automotive digital audio formats, eliminating the need for a separate DAC and analog front end. Typical applications include automotive infotainment head units, external amplifier modules, EV pedestrian warning (AVAS), telematics/eCall audio, rear-seat entertainment, and commercial-vehicle audio. The device is especially suited for designs where four channels of clean audio must be delivered from a 19V rail with minimal inductor count and integrated diagnostic coverage. When designing with the TAS6754QDKQRQ1, provide sufficient copper area on the exposed thermal pad and keep the output LC filter close to the device to minimize EMI. Verify the digital audio source timing and protocol against the datasheet before PCB layout.
TDA18214AHN/C1,557 - Silicon TV Tuner IC DVB-T | NXP
The NXP Semiconductors TDA18214AHN/C1,557 is a high-performance silicon tuner IC designed for digital terrestrial and digital cable TV reception, controlled via an I2C serial interface and housed in a 40-pin HVQFN (6x6 mm) exposed-pad package. The part delivers a Low IF (LIF) output signal to an external demodulator and supports all major digital TV standards including DVB-T. A silicon tuner is an integrated RF receiver front-end that replaces the can-tuned varactor modules used in legacy analog televisions. Within the receiver signal chain hierarchy, it sits at the top: antenna or cable input -> silicon tuner (RF amplification, image-reject mixing, channel filtering) -> Low IF output -> demodulator IC -> transport stream. Because tuning, gain control, and filtering are all implemented on-chip, the TDA18214 family dramatically reduces board area, BOM count, and factory alignment effort compared with discrete tuner designs. Key features of the TDA18214AHN include single-conversion architecture delivering a Low IF signal, full I2C bus control for channel selection and gain programming, support for all digital terrestrial and cable TV standards (DVB-T, DVB-C, ISDB-T, ATSC, DTMB families), and an exposed-pad 40-HVQFN package suitable for compact set-top box and TV main boards. Surface-mount construction supports standard reflow assembly. Architecturally, the TDA18214 integrates a low-noise RF amplifier, image-reject downconversion mixer, broadband synthesizer, and channel-selection filtering in a single CMOS/BiCMOS die. Delivering LIF directly to the demodulator eliminates SAW-filter-heavy IF stages in many designs, and the digital-controlled gain distribution optimizes linearity versus noise figure across the received channel. Typical applications include digital set-top boxes, integrated digital TV (iDTV) main boards, USB TV tuner dongles, PC-TV capture cards, and cable/terrestrial hybrid receivers. Its broad standards support lets one design serve multiple regional markets with firmware changes only. Design consideration: as a 6x6 mm HVQFN with exposed pad, the thermal and ground path depends on the PCB land pattern; the exposed pad must be soldered to a solid ground plane with thermal vias, and the I2C bus requires proper pull-up sizing for reliable 100/400 kHz communication. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Note that this part is marked Obsolete (last buy March 31, 2016; last delivery June 30, 2016), so availability is limited to remaining distributor and broker stock as of 2026-10-11.
TDA2009A - 10W+10W Stereo Class-AB Audio Amplifier | STMicroelectronics
The STMicroelectronics TDA2009A is a class-AB dual Hi-Fi audio power amplifier assembled in a Multiwatt® package, delivering 10 W + 10 W of continuous output power per channel into 8 Ω loads (stereo operation from 8 V to 28 V supply). The device is specially designed for high quality stereo applications such as Hi-Fi music centers, mini-component stereos, multimedia speaker systems, and instrument amplifiers that demand dual-channel output from a single, well-protected IC. What is a class-AB audio power amplifier? A class-AB amplifier is the most common bipolar topology used in mid-power audio reproduction; it biases its output stage so that push and pull transistors each conduct for slightly more than half a cycle. This eliminates the crossover distortion of pure class-B designs while keeping efficiency far higher than class-A. The TDA2009A instantiates that topology with on-chip short-circuit protection, thermal shutdown, and AC short-circuit protection of the load, integrating a complete stereo driver into one Multiwatt-11 power package with the heatsink tab on the back. Key features include 10 W + 10 W continuous output into 4 Ω with THD = 10 % at 14 V / 4 Ω (per ST datasheet), 1 % THD typical at lower levels, an operating supply range of 8 V to 28 V, 3 A peak output current per channel, very low harmonic and crossover distortion, and internal protection against short circuits, thermal overload, and DC voltage on the load. The Multiwatt-11 (Pentawatt-style) package exposes a metal tab so the part itself forms the heatsink, simplifying PCB mechanical design. The architecture uses a vertical bipolar power process with quasi-complementary NPN/PNP output pairs, a unity-gain inverting topology per channel, and internal bias generators that minimize quiescent crossover glitch. The result is a flat frequency response from 20 Hz to 20 kHz with low 0.1 % harmonic content, suitable for full-range music reproduction without complex external compensation networks. Typical applications include stereo Hi-Fi music centers, multimedia speaker systems, TV audio output stages, guitar and instrument practice amplifiers, automotive radios (with 14 V supply), and self-powered USB speakers where dual-channel audio from a single chip replaces two single-channel modules. When designing with this device, place a 100 nF decoupling capacitor on the supply pin as close as possible to the IC, use feedback resistors of 39 kΩ for closed-loop gain near 35 dB, and provide adequate heatsinking through a clip-on or bonded tab. The package tab is electrically tied to the -Vs pin (or to the substrate in some legacy datasheets) - consult the datasheet pinout before insulating the heatsink. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes for the TDA2009A, providing information not consolidated on any single distributor product page.
TDA7297 - 15W+15W Dual Bridge Amplifier | STMicroelectronics
The STMicroelectronics TDA7297 is a dual bridge Class-AB audio amplifier delivering 15W+15W output power in a 15-pin Multiwatt package, designed specifically for TV and portable radio applications. It operates from a wide 6V to 18V supply range and uses an internally fixed gain topology that eliminates the need for SWR capacitors, bootstrap networks, and Boucherot cells. A Class-AB (dual bridge) audio amplifier is a topology that combines two push-pull output stages in a bridge-tied-load (BTL) configuration, allowing higher output swing across a speaker load without large DC-blocking capacitors. The TDA7297 belongs to the broader category of integrated audio power amplifiers, which sit within the analog signal chain and power management domains in a typical consumer electronics design. Dual-bridge configurations are especially valued in compact consumer devices because they double the voltage swing across the speaker and remove the need for a bulky output coupling capacitor. Key features include 15W per channel continuous output into 8 ohm loads, low standby current with a dedicated Standby pin, and a Mute function for click-free power-up sequencing. The device integrates all output transistors in the same silicon die and requires only a few external resistors and a power supply bypass network, enabling very compact PCB designs. Typical THD at 1W output is in the 0.1%-0.5% range, making it suitable for entry-level TV audio, multimedia monitors, and portable boombox designs. The internally fixed gain topology simplifies board layout but limits design flexibility compared to externally adjustable amplifiers like the TDA7294. Thermal performance is handled through the Multiwatt-15 package, which exposes the die tab to a vertical heatsink profile with through-hole pins for robust mechanical mounting. Designers must still respect the safe operating area at high ambient temperatures where sustained 2x15W output can push the junction close to thermal limits without adequate heatsinking. Typical applications include flat-panel TV stereo speaker drivers, portable radio boombox amplifiers, LCD monitor audio outputs, PC motherboard sound subsystems, and DIY audio upgrade kits. The part is commonly found in 2.1-channel subwoofer + satellite systems where a third mono channel can be derived by bridging the two outputs in parallel. When designing with the TDA7297, always provide adequate heatsinking through the Multiwatt tab and respect the 6V-18V supply range. The Standby and Mute pins should be sequenced with a 10kohm/10uF RC network as recommended in the datasheet to achieve click-free power transitions.
TDA7379 - 4x13W / 2x38W Class-AB Quad Audio Power Amplifier | STMicroelectronics
The STMicroelectronics TDA7379 is a Class-AB audio power amplifier capable of 4x13W or 2x38W output, housed in a Multiwatt-15 package and intended for car-radio and high-power consumer audio applications. The device operates from an 18V nominal supply (operating up to 28V) and integrates a fixed 26dB BTL gain stage that eliminates the need for external bootstrap capacitors, Boucherot cells, or feedback networks. An additional feature is the CMOS-compatible standby function that drops quiescent consumption during mute conditions. A Class-AB amplifier is a linear audio power amplifier in which the output transistors are biased into partial conduction, reducing crossover distortion compared to pure Class-B while achieving higher efficiency than Class-A. Within the broader taxonomy, the TDA7379 belongs to the linear power amplifier family, sitting under the audio power amplifier category, which in turn is part of the signal-chain / amplifier IC family. This hierarchy matters because system designers typically select a Class-AB part like the TDA7379 for high-output, low-noise single-supply audio stages where switch-mode solutions would inject unacceptable EMI into the signal path. Key features of the TDA7379 include a minimum external component count (no bootstrap capacitors, no Boucherot cells), internally fixed 26dB BTL gain, a high output power capability (4x13W into 4 ohm in quad single-ended mode or 2x38W into 4 ohm in dual BTL mode), CMOS-compatible standby, short-circuit protection to ground and to VCC, load-dump voltage surge protection, and reversed-battery protection. These features make the part particularly suited to automotive environments where transient voltages and wiring faults are common. The amplifier's quad single-ended / dual BTL topology allows system designers to choose between four channels of moderate-power audio (for a front/rear speaker pair system) or two channels of high-power audio (for a subwoofer or stereo bridge-tied load). Internally fixed gain simplifies design and reduces variability across production boards; the trade-off is that the gain cannot be trimmed externally. Typical applications include car-radio amplifiers, multi-channel automotive head units, active speaker systems, subwoofer amplifiers, public-address (PA) amplifiers, and replacement boards for legacy automotive audio equipment. The Multiwatt-15 through-hole package also makes it a strong candidate for repair and refurbishment of older car-audio head units where the original amplifier IC has failed. When designing with the TDA7379, engineers should keep the supply rails well bypassed (100 nF + 1000 uF minimum) and provide a generous ground plane, as high peak currents flow through the output stage. Output short-circuit detection must be respected - sustained shorts will trigger internal protection, but the design must still ensure the load cannot fault the supply. This page synthesizes distributor pricing, verified drop-in alternatives (same-brand ST TDA family first, then cross-brand equivalents), and practical design notes not found in any single manufacturer datasheet.
TDA8920BTH - 2x100W Class-D Audio Power Amplifier | NXP
The NXP TDA8920BTH is a high-efficiency 2 x 100 W class-D audio power amplifier with very low dissipation, housed in a 24-pin HSOP power package with an exposed thermal pad. It operates over a wide symmetrical supply voltage range of +/-12.5 V to +/-30 V (+/-32 V non-operating) and delivers typical output power of 2 x 100 W into 4 ohm or 8 ohm loads with very low quiescent current. The device can be configured as a single BTL mono channel or as a 2-channel stereo amplifier, and integrates all required analog input, PWM modulator, and gate-drive circuitry for a complete class-D solution. A class-D audio amplifier (also called a switching amplifier) is a type of power amplifier that uses high-frequency pulse-width modulation (PWM) of the audio signal followed by output-stage switching transistors and a low-pass LC reconstruction filter. Compared with classical Class-AB linear amplifiers, class-D topologies achieve dramatically higher efficiency (typically 90%+), far less waste heat, smaller heatsink requirements, and lighter designs, which is why they dominate modern flat-panel TV, soundbar, and portable speaker designs. The TDA8920BTH belongs to the audio amplifier -> power amplifier -> analog IC -> signal chain taxonomy. Key features include differential analog inputs, built-in protection (overcurrent, overtemperature, and undervoltage), selectable BTL/SE mode, mute and standby functions, and an exposed die pad (EP) for direct PCB heatsinking. Its switching frequency is in the typical 350-450 kHz range (data needed for exact figure), enabling use of small output filter inductors and capacitors. The TDA8920BTH uses a self-oscillating or fixed-frequency PWM modulator architecture with feedback after the LC output filter (post-filter feedback), which dramatically reduces distortion and output filter dependency. This topology, combined with NXP's proprietary driver stage, achieves THD figures comparable to high-quality linear amplifiers at a fraction of the power dissipation. Typical applications include home theater and stereo receivers, powered multimedia speakers, subwoofer amplifiers, automotive head-unit booster stages, professional active monitor speakers, and high-end DIY audio builds where 2 x 100 W of clean, efficient power is required in a compact SMD footprint. Its SMD-compatible HSOP24 package also makes it suitable for automated assembly versus the through-hole DBS23P variant (TDA8920BJ). When designing with the TDA8920BTH, pay careful attention to the LC output filter component selection and layout: keep the filter loop area minimal, use low-ESR film or ceramic capacitors, and tie the exposed pad to a large copper pour for thermal management. Always observe the +/-30 V maximum supply rating and include adequate supply decoupling close to the IC pins. This page synthesizes distributor pricing, verified drop-in alternatives (same HSOP24 footprint), practical design notes, and datasheet-based specifications not found on standard distributor listings, giving engineers a complete engineering reference for the TDA8920BTH.
TDF8546TH/N2 - 4x45W BTL Class-AB Car Audio Amplifier | NXP
The NXP TDF8546TH/N2 is an I2C-bus controlled, quad Bridge-Tied Load (BTL) Class-AB automotive audio power amplifier delivering 4 x 45 W into 4 Ω in the 36-pin HSOP (Heatsink Small Outline Package) with exposed thermal pad. It is intended for head-unit and external amplifier applications in 12 V vehicles, with full I2C diagnostics, start-up diagnostics, and best-efficiency switching modes for reduced dissipation during low-to-medium output. What is a quad BTL Class-AB automotive amplifier? A BTL (Bridge-Tied Load) audio amplifier drives each speaker differentially across two outputs, doubling the voltage across the load and quadrupling the achievable output power versus a single-ended topology for a given supply rail. The Class-AB output stage combines bipolar output transistors biased to minimize crossover distortion while preserving high efficiency at moderate output levels, making it the long-standing industry choice for in-vehicle audio. NXP's TDF family falls within the broader power management / amplifier IC hierarchy: Audio Amplifier -> Class-AB Amplifier -> Automotive Audio Amplifier -> Power Management IC -> Semiconductor. Key features of the TDF8546 include operation from a battery supply as low as 6 V (suited to stop/start vehicles), best-efficiency mode that dynamically adjusts output stage biasing, full I2C-bus controlled diagnostics including start-up and runtime load diagnostics, and independent channel gain control. The integrated thermal foldback and over-current protection safeguard the exposed pad / the top-side body of the HSOP package, which is itself the primary heat-dissipation path. The device uses a complementary bipolar output architecture with on-chip gate drivers and charge-pump generation for the high-side NPN transistors, eliminating the need for external bootstrap capacitors. I2C control permits mode switching, mute/unmute, and read-back of diagnostic flags from the host microcontroller, simplifying ECU software development. Typical applications include automotive head units and infotainment amplifiers, external booster amplifiers for premium sound systems, and stop/start-compliant audio platforms where cranking dips below 8 V are common. The combination of best-efficiency operation and low quiescent current helps meet stringent vehicle standby-current budgets. When designing with this part, ensure the HSOP exposed thermal pad is soldered to a copper area of at least 6 cm² for full 4 x 45 W output. Use low-ESR electrolytic bypass capacitors within 10 mm of the supply pins, and keep the I2C lines away from the output traces to avoid coupling. Consider heatsink attachment for sustained high-output operation. This page synthesizes distributor pricing, end-of-life status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TFA9865 - 7W CoolPWM Smart Class-D Amplifier | Goodix
The Goodix TFA9865 is a high-performance, fully digital Class-D smart audio amplifier delivering 7 W peak output power with an ultra-low noise floor below 7 uV, housed in an extremely compact 2.2x2.2 mm WLCSP package. It targets mobile and portable audio applications where board area, quiescent power, and acoustic clarity are simultaneously critical design constraints. A Class-D audio amplifier is a switching-mode power stage that converts a PWM or PDM waveform into a high-efficiency audio output, driving a loudspeaker directly through an LC reconstruction filter. Within the broader audio IC taxonomy, the TFA9865 sits in the smart amplifier sub-category of power management and signal chain ICs, sitting alongside traditional Class-AB amplifiers but achieving far higher efficiency (typically >85 %) and lower thermal dissipation. Goodix's first-generation CoolPWM architecture is a proprietary, fully digital modulation scheme that breaks away from conventional Class-D topologies to minimize EMI and audible idle-channel noise. Key specifications include 7 W peak output into a typical 4 ohm or 8 ohm speaker load, an idle-channel noise floor of less than 7 uV, integrated DSP-based speaker protection algorithms, I2C/TDM control interface, and a small WLCSP footprint enabling direct placement adjacent to the smartphone or tablet speaker. Compared with discrete analog Class-D solutions, the TFA9865 reduces BOM count by integrating gate drivers, MOSFET power stage, and digital modulation in a single die. The CoolPWM digital architecture leverages advanced manufacturing processes to deliver high audio performance with very low power consumption. Built-in adaptive excursion control and thermal protection extend the usable loudness envelope of small speakers without causing voice-coil damage. This makes the device well suited to handset, tablet, and portable speaker applications where designers must push SPL limits within tight thermal budgets. Typical applications include smartphone and tablet loudspeaker amplification, portable Bluetooth speakers, wearable audio devices, and notebook/laptop speakers. The part is commonly paired with Goodix or third-party audio CODECs and digital microphone pre-processors to form a complete mobile audio playback chain. When designing with the TFA9865, pay close attention to PCB layout of the LC output filter, the placement of the bootstrap capacitor, and the thermal pad connection. Use a 4-layer stack-up with a solid ground plane directly beneath the part to minimize EMI coupling into adjacent RF circuits. This page synthesizes distributor pricing, drop-in alternatives, application examples, and practical design notes not found in the manufacturer product brief.
THS3061DGN - 300MHz CFA, 7000V/us Slew Rate | Texas Instruments
The Texas Instruments THS3061DGN is a single high-voltage, high slew-rate current feedback amplifier delivering 300 MHz unity-gain bandwidth, 7000 V/us slew rate, and +/-145 mA output current into 50 ohms, housed in an 8-pin HVSSOP (DGN) package with PowerPAD thermal pad. A current feedback amplifier (CFA) is a type of high-speed operational amplifier whose architecture uses a low-impedance inverting input to achieve bandwidth that is largely independent of closed-loop gain. In the signal-chain hierarchy, the CFA sits within the amplifier IC family alongside voltage feedback op amps (VFA) and fully differential amplifiers, and is preferred where wide bandwidth and fast settling must be maintained without the gain-bandwidth product penalty of VFAs. Key features include 7000 V/us slew rate for large-signal high-frequency performance, 0.1 dB gain flatness bandwidth of 120 MHz at a gain of 2, low distortion of -81 dBc at 10 MHz, and high output drive of +/-145 mA into 50 ohm loads. These parameters suit the device for driving ADC inputs, coaxial cables, and other low-impedance loads directly. The THS3061 is fabricated on Texas Instruments' BICOM-1 complementary bipolar process, enabling high-voltage operation (up to +/-15 V class supplies) with high-speed performance. The current feedback topology keeps bandwidth relatively constant across gain settings, while the PowerPAD package provides a low thermal resistance path essential for high-output-current operation. Typical applications include pulse amplifiers, RF/IF signal chains, high-speed data acquisition front ends, video line drivers, and test-and-measurement signal sources. Design consideration: as a CFA, the feedback resistor value must be selected per the datasheet recommendations; lowering Rf to increase bandwidth can cause peaking and instability. Ensure proper PowerPAD soldering to the PCB ground plane for thermal performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
THS3061DGNR - 300MHz 7000V/us CFB Amplifier | Texas Instruments
The Texas Instruments THS3061DGNR is a single-channel, high-voltage, high-slew-rate current-feedback (CFB) amplifier delivering a 300 MHz unity-gain bandwidth, a 7000 V/us slew rate, and up to +/-145 mA of output current into a 50 ohm load, housed in an 8-pin HVSSOP (DGN) package with PowerPAD thermal pad. It operates from supplies up to +/-15 V (30 V total). A current-feedback amplifier is a type of high-speed operational amplifier whose bandwidth is largely independent of closed-loop gain, making it a member of the broader amplifier hierarchy: CFB amplifier -> high-speed op amp -> operational amplifier -> analog signal-conditioning IC. Unlike voltage-feedback amplifiers, CFAs use a low-impedance inverting input and a current-driven internal stage, which is what enables their exceptional slew rates. Key features of the THS3061 include a 0.1 dB flatness bandwidth of 120 MHz at a gain of 2, second-harmonic distortion of -81 dBc at 10 MHz, and high output drive current of +/-145 mA, per the TI datasheet. These specs suit applications that need both speed and signal swing into low impedances. The device is fabricated on the TI BICOM-1 complementary bipolar process, which underpins its combination of high breakdown voltage (up to 30 V total supply) and high-frequency performance. The PowerPAD HVSSOP-8 package provides a low thermal-impedance path to the PCB, essential when driving heavy loads at high frequency. Typical applications include high-voltage pulse and laser-diode drivers, ADC input drivers in test and measurement equipment, video and communications signal chains, and active probes requiring high slew rate with substantial output current. Design consideration: because this is a current-feedback amplifier, the feedback resistor value should be kept close to the datasheet-recommended range; increasing RF reduces bandwidth and stabilizes the loop, while decreasing it can cause peaking or oscillation. This page synthesizes distributor availability data, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet. Pricing references are as of 2026-09-13.
THS4031 - 100MHz 1.6nV Low-Noise Op Amp | Texas Instruments
The Texas Instruments THS4031 is a single-channel, ultra-low voltage noise, high-speed voltage feedback amplifier delivering a 100-MHz bandwidth at gain of 2, a 100-V/us slew rate, and a 60-ns settling time (0.1%). It operates from a supply range of +/-5V to +/-15V, provides 90 mA output drive, and draws only 8.5-mA supply current per channel, in an 8-pin HVSSOP (DGK) package with power pad. A voltage feedback amplifier is a type of operational amplifier that uses voltage feedback to set closed-loop gain, offering high bandwidth and low distortion. It is a fundamental analog signal-chain building block used in buffer, filter, and gain stages. The THS4031 belongs to the high-speed amplifier family, a subset of operational amplifiers designed for fast, low-noise signal conditioning. Key features include ultra-low 1.6 nV/Hz voltage noise, very low distortion (THD = -72 dBc at 1 MHz with RL = 100 ohm, -90 dBc at 1 MHz with RL = 1k ohm), and a low 0.5-mV typical input offset voltage. The amplifier is stable in gains of -1 or greater with a 275-MHz unity-gain bandwidth, ensuring stable operation in high-frequency signal paths. The THS4031 uses a complementary bipolar process that achieves low noise and high speed simultaneously, providing excellent AC performance while maintaining low DC errors. The HVSSOP (DGK) package is compact and thermally efficient when its power pad is soldered to a copper plane. Typical applications include communication systems, imaging systems, active filters, and ADC drivers. In communication receivers, the 1.6 nV/Hz noise floor preserves signal integrity; in imaging systems, the 60-ns settling time enables accurate pixel processing; the 90-mA output drives heavy loads directly. Design tip: decouple supplies with 0.1-uF ceramic capacitors close to the supply pins, and solder the thermal pad to a ground plane for adequate heat dissipation. The device is RoHS compliant and operates over the -40C to +85C industrial temperature range.
THS4031CDGNR - 100MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments THS4031CDGNR is a single-channel, 100 MHz low-noise high-speed voltage-feedback amplifier delivering 1.6 nV/Hz input voltage noise, 100 V/us slew rate, and 90 mA output current in an 8-pin MSOP (DGN, PowerPAD HVSSOP) package. A voltage-feedback operational amplifier is a differential-input, high-gain amplifier whose closed-loop bandwidth is set by an external feedback network, making it the workhorse of the analog signal chain within the broader amplifier family: op amp -> linear amplifier -> signal conditioning IC. Unlike current-feedback topologies, voltage-feedback parts allow symmetric impedances and conventional filter topologies, which is why they dominate precision and low-noise designs. Key features of the THS4031CDGNR include ultra-low 1.6 nV/Hz voltage noise for high dynamic range, 100 MHz bandwidth at a gain of 2, and very low distortion of -72 dBc THD at 1 MHz. The 60 ns settling time to 0.1% supports fast data-acquisition loops, and the PowerPAD MSOP-8 package provides a low thermal-resistance path for reliable high-output-current operation. Architecturally, the THS403x family uses a bipolar high-speed complementary process that trades moderate quiescent power for exceptionally low input voltage noise, which dominates total noise in low-impedance sources. The 0.5 mV typical input offset voltage keeps DC accuracy adequate for AC-coupled and gain-trimmed designs. Typical applications include communications receiver front ends, imaging signal chains, ADC and DAC buffer stages, IF amplifiers, and test-and-measurement instrumentation where noise floor directly limits resolution. Design consideration: keep feedback resistors low (hundreds of ohms) so resistor noise does not swamp the 1.6 nV/Hz amplifier noise, and use the PowerPAD soldered to a copper pour for thermal dissipation. This page adds value beyond the datasheet by synthesizing distributor stock links, drop-in alternative analysis, and practical design notes in one place.
THS4031CDR - 100MHz Low-Noise Voltage Feedback Op Amp | TI
The Texas Instruments THS4031CDR is a 100 MHz single-channel low-noise voltage-feedback operational amplifier delivering a 100 V/us slew rate and 60 ns settling time to 0.1%, supplied in an 8-pin SOIC (D) package on tape and reel. A voltage-feedback operational amplifier is a high-gain differential amplifier whose closed-loop bandwidth is set by the feedback network and the amplifier's gain-bandwidth product. Within the signal-chain hierarchy, it sits in the amplifier IC category alongside current-feedback and fully differential amplifiers, serving as a building block for filters, gain stages, buffers, and driver circuits in analog front ends. Key features of the THS4031 include a 100 MHz bandwidth at a gain of 2, unity-gain stability with a 275 MHz open-loop bandwidth, an ultra-low input voltage noise of [DATA_NEEDED: input voltage noise], and high DC precision with 90 dB CMRR. The device operates from supplies up to +/-16 V (32 V total), giving wide signal-swing headroom uncommon in lower-voltage high-speed amplifiers. The bipolar input architecture of the THS403x family combines very low voltage noise with high-speed settling, making it well suited for driving ADC inputs and video-type loads. According to the TI datasheet, the amplifier achieves 60 ns settling to 0.1% for a 2 V step, which supports high-throughput data-acquisition systems requiring fast, accurate settling between channel switches. Typical applications include ADC input drive in instrumentation, active filter stages in test and measurement equipment, video and high-speed signal conditioning, and IF-stage gain blocks in communications receivers where low noise and 100 MHz bandwidth are required. Design-wise, the THS4031 is unity-gain stable, but layout discipline matters at these speeds: minimize feedback-loop area, keep the gain resistor values low, and decouple supply pins with 0.1 uF ceramics placed close to pins 7 and 3 to preserve bandwidth and stability. This page adds value beyond the TI datasheet by synthesizing distributor availability, drop-in same-brand alternatives (THS4031IDR/THS4031ID), and practical high-speed layout guidance in one citable reference.
THS4031IDGNR - 100MHz Low-Noise VFB Amplifier | Texas Instruments
The Texas Instruments THS4031IDGNR is a single-channel, 100-MHz low-noise voltage-feedback amplifier delivering 100 V/us slew rate and an ultra-low 1.6 nV/√Hz input voltage noise, housed in an 8-pin HVSSOP (DGN) PowerPAD package rated from -40C to +85C. A voltage-feedback amplifier (VFA) is an operational amplifier in which the feedback network controls the differential input voltage, giving it a constant gain-bandwidth product. Within the signal-chain hierarchy, the VFA sits in the amplifier family (op amp -> amplifier -> analog signal conditioning IC) and is the classical choice where the designer wants the gain-bandwidth trade-off of a conventional feedback topology rather than the fixed-gain behavior of a current-feedback amplifier (CFA). The defining feature of the THS4031 is its 1.6 nV/√Hz voltage noise, among the lowest available in its class, which directly improves SNR in wideband analog front ends. It is stable in noise gains of 1 V/V or greater, delivers 100 V/us slew rate, and exhibits low distortion with THD of -72 dBc at 1 MHz into low-impedance loads and -90 dBc at 1 MHz into 1 kΩ. The typical input offset voltage is only 0.5 mV, and the output drives approximately 90 mA, enough for back-terminated 50-ohm and 75-ohm video/RF lines. Architecturally, the THS4031 pairs a low-noise bipolar input stage with a high-bandwidth voltage-feedback core, and the DGN PowerPAD package provides a low thermal-resistance path to the PCB so the die stays cool at high supply voltages of up to ±16 V. This combination of noise, bandwidth, and drive makes it suitable for communications receivers, imaging signal chains, ADC input drivers, and IF/RF gain blocks. Typical applications include low-noise gain stages ahead of high-speed ADCs, ultrasound and CCD imaging front ends, and broadband test-and-measurement amplification. The supply range of ±4.5 V to ±16 V supports both ±5 V and ±15 V analog rails. Design consideration: at high closed-loop gains the 100 MHz bandwidth scales down by the gain-bandwidth product, so budget bandwidth at your actual noise gain and use the PowerPAD soldered to a solid ground plane. This page adds distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
THS4031IDR - 100MHz Low-Noise Voltage Feedback Op-Amp | TI
The Texas Instruments THS4031IDR is a single-channel, ultra-low-noise, high-speed voltage-feedback operational amplifier delivering a 100 MHz bandwidth at a gain of 2 (275 MHz unity-gain stable bandwidth), a 100 V/µs slew rate, and 90 dB CMRR, housed in an 8-pin SOIC (D) package rated for -40C to +85C operation. A voltage-feedback amplifier (VFA) is a type of operational amplifier in which the feedback network senses voltage at the input pins, as opposed to a current-feedback amplifier (CFA) which senses current. Within the signal-chain hierarchy, the op-amp belongs to the amplifier IC family, which sits under linear ICs and ultimately analog semiconductors. Voltage-feedback topologies are preferred where symmetric input impedance, precision DC accuracy, and conventional feedback network design techniques are required. Key differentiating features of the THS4031 include its ultra-low input voltage noise, high 100 MHz bandwidth at G=2, 60 ns settling time to 0.1%, and high output drive capability. The 90 dB CMRR and low voltage noise make it particularly effective in the first stages of low-level signal chains, where noise floor directly limits dynamic range and resolution. Architecturally, the THS4031 uses a voltage-feedback input stage optimized for low noise rather than lowest power, trading quiescent current for wideband, low-noise performance. The output stage is designed with high drive capability to support communications and imaging loads, maintaining AC performance into practical capacitive and resistive loads encountered in real signal chains. Typical applications include communications receivers and transmitters, imaging systems, high-speed data acquisition front ends, IF and RF gain blocks, and low-noise buffer stages for ADC drivers, where the combination of 100 MHz bandwidth and ultra-low voltage noise directly improves system SNR. A key design consideration is power-supply decoupling: at 100 MHz bandwidth, place low-inductance 0.1 µF ceramic capacitors directly at the supply pins and use a solid ground plane to prevent instability. Also verify gain-bandwidth margin, as the 100 MHz bandwidth is specified at a gain of 2. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in a single manufacturer datasheet, providing unique cross-reference value for engineers and buyers.