집적 회로

하위 카테고리

📁 ADC/DAC 2520 제품 📁 증폭기 IC 800 제품 📁 오디오 코덱 16 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 314 제품 📁 DSP 963 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 6666 제품 📁 인터페이스 IC 1603 제품 📁 LED 드라이버 1 제품 📁 로직 IC 305 제품 📁 메모리 IC 875 제품 📁 마이크로컨트롤러 18756 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 13 제품

제품 (32865)

ADS5237IPAGT - Dual 10-Bit 65MSPS +3.3V ADC | Texas Instruments
ADS5237IPAGT

ADS5237IPAGT - Dual 10-Bit 65MSPS +3.3V ADC | Texas Instruments

The Texas Instruments ADS5237IPAGT is a dual-channel, 10-bit, 65-MSPS pipelined analog-to-digital converter (ADC) housed in a 64-pin TQFP (10x10 mm) package. The part is specified for industrial temperature grade (-40C to +85C), operates from a single +3.3V analog supply, and integrates two complete ADC channels with high-bandwidth sample-and-hold amplifiers per channel, supporting fully differential inputs. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous-time analog signals into discrete digital codes at a specified sampling rate. Pipelined ADCs like the ADS5237IPAGT use a multi-stage architecture in which each stage resolves a few bits and passes the residue to the next stage, achieving the best trade-off among sampling speed (tens to hundreds of MSPS), resolution (8-14 bits), and active power consumption. Within the broader taxonomy, the ADS5237IPAGT sits in: ADC -> data converter -> mixed-signal IC -> semiconductor. Pipelined ADCs are widely used in applications that demand high throughput with moderate dynamic range. Key specifications include 65 MSPS maximum sampling rate per channel, 10-bit resolution, dual independent channels, +3.3V single supply operation, and industrial temperature range. The pipelined architecture delivers excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) for IF-sampling and baseband digitization. Internal reference and high-bandwidth track-and-hold simplify board design by reducing external component count. The ADS5237IPAGT employs a proprietary multi-stage pipeline with per-stage MDAC and flash sub-ADC blocks, followed by error-correction logic and CMOS output drivers. Digital output data is presented in offset-binary format and latched on rising or falling clock edges. The 64-pin TQFP package provides adequate thermal dissipation (theta_JA approximately 45 C/W typical) for continuous dual-channel operation at full 65 MSPS without additional heatsinking. Typical applications include portable and benchtop ultrasound imaging, digital oscilloscope front-ends, communications IF/baseband digitizers, CCD/CIS imaging digitizers, and high-speed data acquisition systems. The dual-channel architecture is particularly attractive for I/Q demodulation or dual-antenna diversity receivers where PCB area and BOM cost must be minimized. When designing with the ADS5237IPAGT, place decoupling capacitors (0.1 uF and 10 uF) as close as possible to each AVDD pin, route the analog and digital grounds as separate planes joined at a single point under the IC, and keep the clock trace short and matched to minimize aperture jitter degradation. The single +3.3V supply simplifies power-tree design versus 5V ADC alternatives. This page synthesizes distributor pricing, drop-in TQFP-64 alternatives, and practical PCB layout notes not consolidated on the manufacturer datasheet, with cross-brand parts explicitly sourced from the TI cross-reference search and distributor parametric tools.

견적 요청 문의하기
ADS5296RGCR - 12-Bit 80MSPS 8-Channel ADC | Texas Instruments
ADS5296RGCR

ADS5296RGCR - 12-Bit 80MSPS 8-Channel ADC | Texas Instruments

The Texas Instruments ADS5296RGCR is a 12-bit resolution, 80-MSPS sampling rate, 8-channel pipelined analog-to-digital converter housed in a 64-pin VQFN (RGC) package measuring 9x9 mm with an exposed thermal pad. The device integrates eight low-power, high-dynamic-range ADCs that share a common reference and sample clock, plus on-chip digital processing blocks including digital gain, offset correction, and a digital filter that simplifies downstream FPGA/CPLD interfacing. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts real-world analog voltages into discrete digital codes for processors, FPGAs, or DSPs to analyze. Within the converter hierarchy, the ADS5296 belongs to the pipeline ADC subclass, which uses a multi-stage switched-capacitor architecture to achieve high sampling rates (tens to hundreds of MSPS) at moderate resolution (8-14 bits); pipelined ADCs sit between successive-approximation (SAR) ADCs (slow, high-resolution) and flash ADCs (fast, low-resolution). Pipelined ADCs are the workhorse of medical imaging, communications, and multi-channel data acquisition. Key features include 12-bit resolution, 80 MSPS maximum sampling rate, 8 simultaneous sampling channels, LVDS/CMOS digital outputs, SNR of 70 dBFS at 10 MHz input, SFDR of 86 dBc, and 1.8 V analog supply with 3.3 V digital I/O supply. The integrated digital gain from 0 dB to 12 dB and per-channel offset correction up to +/- 96 LSB reduce system calibration complexity. Architecturally, the ADS5296 uses a fully differential switched-capacitor pipeline core with a proprietary multi-bit per-stage architecture and on-chip dithering to enhance spurious-free dynamic range. The eight ADC channels operate from a shared PLL-derived internal clock and a shared bandgap reference, ensuring tight inter-channel gain and offset matching for beamforming and parallel sampling applications. Typical applications include medical imaging ultrasound receivers, multi-channel communications test equipment, portable instrumentation, security and surveillance imaging, and phased-array radar preprocessing. The 80 MSPS per-channel rate supports IF sampling in communications and direct-downconversion of baseband signals up to approximately 35 MHz. Design considerations for the ADS5296RGCR include careful PCB layout to maintain the LVDS output timing budget; a low-jitter external clock is essential because aperture-jitter sensitivity sets the SNR ceiling at high input frequencies. The VQFN-64 exposed pad must be soldered to a continuous ground plane for both thermal dissipation (the RGC package carries a low thermal resistance) and low-impedance return paths for the analog inputs. This page synthesizes distributor pricing as of 2026-10-11, drop-in RGC-64 alternatives, and PCB layout guidance that go beyond the manufacturer datasheet alone.

견적 요청 문의하기
ADS5296RGCT - 12-Bit 80-MSPS 8-Ch ADC | Texas Instruments
ADS5296RGCT

ADS5296RGCT - 12-Bit 80-MSPS 8-Ch ADC | Texas Instruments

The Texas Instruments ADS5296RGCT is a high-performance, low-power 12-bit, 80-MSPS, 8-channel pipelined analog-to-digital converter (ADC) housed in a 64-pin VQFN (9 mm × 9 mm) package with an exposed thermal pad. It integrates eight simultaneously-sampling ADC channels that deliver 12-bit resolution at up to 80 MSPS per channel, sharing a common clock and reference to simplify synchronization across channels. The device operates from a single 1.8 V analog supply and a 1.8 V–3.3 V digital I/O supply, drawing only 90 mW per channel at 80 MSPS, making it attractive for high-channel-count data acquisition cards that must fit within tight thermal budgets. An analog-to-digital converter (ADC) is a data-converter integrated circuit that samples continuous-time analog voltage signals and outputs discrete multi-bit digital codes at a fixed sampling rate. Multi-channel pipelined ADCs such as the ADS5296RGCT fall into the broader hierarchy of data converter ICs -> ADC -> successive-approximation / pipeline / SAR / sigma-delta / flash ADC -> signal-chain semiconductor. Compared with integrating or SAR converters, pipeline ADCs deliver the highest sample rates (tens to hundreds of MSPS) while maintaining 10-14 bit resolution, at the cost of a few clock cycles of pipeline latency. The ADS5296RGCT lands squarely in the multi-channel, mid-resolution, high-speed category used in medical imaging, communications test, and industrial inspection. Key features of the ADS5296RGCT include a 12-bit resolution with no missing codes, 70 dB SNR at 10 MHz input and 80 MSPS, an internal reference (with optional external reference), LVDS DDR and CMOS digital output modes, and per-channel power-down control. An integrated digital gain-and-offset correction block lets designers trim inter-channel matching on the fly. The integrated low-jitter PLL operates from a single LVDS/CMOS clock and generates all internal sample timing, eliminating the need for an external track-and-hold clock. Typical applications include medical imaging receivers (ultrasound beamformers, CT detector boards), industrial machine-vision and inspection multi-channel boards, communications test equipment and wideband digitizers, and defense / surveillance phased-array front ends. Channel-count reduction at lower power is supported through software-configurable channel enabling. When designing with the ADS5296RGCT, place the 0.1 µF / 10 µF analog-supply decoupling network within 5 mm of the AVDD pins, keep analog and digital return currents separated back to a single ground star under the exposed pad, and follow TI's recommended LVDS 100-Ω termination pattern on the digital outputs to avoid reflections at 80 MSPS. Thermal management is critical: at full-channel 80 MSPS operation the device dissipates approximately 720 mW and benefits from a 6-layer PCB thermal via array under the EP. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical 8-channel ADC design notes not found in a single distributor listing.

견적 요청 문의하기
ADS5400HFS/EM - 12-bit 1-GSPS QMLV ADC | Texas Instruments
ADS5400HFS/EM

ADS5400HFS/EM - 12-bit 1-GSPS QMLV ADC | Texas Instruments

The Texas Instruments ADS5400HFS/EM is a 12-bit, 1-GSPS (giga-sample per second) analog-to-digital converter (ADC) in the HiRel QMLV radiation-hardened family, packaged in a 100-pin ceramic CFP (Cavity Filled Package). It operates from dual supplies of 5V (analog) and 3.3V (digital), producing LVDS-compatible digital outputs that interface cleanly to high-speed FPGAs and ASICs. According to the Texas Instruments product page, the analog input buffer isolates the internal track-and-hold switching transients from disturbing the upstream signal source, preserving signal integrity at the converter's full Nyquist input bandwidth. A radiation tolerance of 50 krad(Si) total ionizing dose and a military-grade -55C to +125C operating range make this part qualified for satellite payloads, missile guidance, and downhole drilling electronics. An analog-to-digital converter (ADC) is a semiconductor device that samples a continuous analog voltage and quantizes each sample into a discrete digital code, bridging the analog signal chain to the digital processing domain. Pipeline ADCs in particular use a multi-stage architecture where each stage performs a low-resolution flash conversion and residue amplification, enabling high sample rates at moderate resolution. The 12-bit, 1-GSPS ADS5400HFS/EM sits at the intersection of instrumentation and HiRel aerospace/defense, where the LVDS digital interface simplifies board-level routing at multi-gigabit aggregate data rates. Key differentiating specifications of the ADS5400HFS/EM include 1-GSPS guaranteed sample rate, 12-bit resolution with pipelined architecture, internal analog input buffer with 50-ohm friendly input structure, and LVDS digital outputs that support both DDR and SDR clocking modes. The 100-CFP ceramic sealed package provides hermeticity required for military and space programs. According to TI documentation, the converter consumes roughly 2.2 W from the 5V rail, requiring careful thermal management via the package's thermal pad and PCB copper pours. From an architectural perspective, the pipelined core samples one input per clock cycle, with internal calibration to correct inter-stage gain and offset mismatch. The integrated input buffer is a notable feature: many 1-GSPS ADCs require an external front-end amplifier, but the ADS5400HFS/EM directly drives 50-ohm sources up to several hundred MHz of analog input bandwidth, simplifying the bill of materials in radar and electronic-warfare receivers. Typical applications include phased-array radar I/Q data conversion, electronic countermeasure (ECM) receivers, satellite downlink digitizers, military test and instrumentation, and high-energy physics data acquisition. The wide -55C to +125C temperature range and TID tolerance also fit downhole oil/gas telemetry tools that operate in 175C+ boreholes with derating. When designing with this converter, follow datasheet high-speed PCB layout practices: solid ground planes, controlled-impedance LVDS traces (100-ohm differential), short analog input traces with 50-ohm termination, and isolated analog/digital supply domains. Decoupling must use low-ESL ceramics placed within 5 mm of supply pins. Engineers upgrading from the commercial ADS5400 to this HiRel part benefit from pin compatibility that preserves board layout across prototype and flight builds.

견적 요청 문의하기
ADS5411IPJYRG3 - 11-Bit 105MSPS ADC, 5V Supply, 52-QFP | Texas Instruments
ADS5411IPJYRG3

ADS5411IPJYRG3 - 11-Bit 105MSPS ADC, 5V Supply, 52-QFP | Texas Instruments

The Texas Instruments ADS5411IPJYRG3 is an 11-bit, 105-MSPS pipelined analog-to-digital converter that operates from a single 5V supply and provides 3.3V CMOS-compatible digital outputs, housed in a 52-pin QFP (HLQFP, 10x10 mm) package. It delivers 11-bit resolution at sampling rates up to 105 MSPS, supports a 2.2 Vp-p analog input range, and integrates an on-chip input buffer that isolates the internal track-and-hold from external signal sources. An analog-to-digital converter (ADC) is a data-acquisition component that samples continuous analog signals and outputs discrete digital codes, forming the bridge between the analog front end and the digital signal-processing domain. Within the broader semiconductor taxonomy, ADCs belong to data-converter ICs, which sit inside signal-chain semiconductors and ultimately under the mixed-signal IC umbrella. Pipelined ADCs in particular use a multi-stage architecture to achieve high sampling rates while keeping per-stage hardware modest, making them the workhorse choice for intermediate-speed, moderate-resolution IF, instrumentation, and imaging applications. Key features of the ADS5411 include an integrated input buffer for source isolation, a low-noise clock interface with LVPECL/LVDS/LVCMOS compatibility, and 3.3V CMOS outputs that simplify interfacing with FPGAs, ASICs, and DSPs without level shifters. The part uses a single 5V analog supply and a 3.3V digital supply, with a digital-down-format option for flexible data capture. The device uses a multi-stage pipelined architecture with proprietary calibration, providing excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) at the rated 105 MSPS. A differential clock input supports on-chip clock-doubler operation, while the integrated input buffer eliminates the need for an external high-bandwidth ADC driver in many systems. The 52-QFP footprint offers generous thermal headroom and good PCB manufacturability for prototype builds. Typical applications include communications IF-signal digitization, industrial test and measurement equipment, medical imaging front ends, radar and sonar intermediate-frequency sampling, and high-speed data acquisition cards. Its 11-bit resolution strikes a balance between dynamic range and system cost where 8-bit ADCs are too coarse but 14-bit parts are unnecessary. When designing with the ADS5411, ensure that the analog input is AC-coupled and properly terminated, since the on-chip input buffer expects a 2.2 Vp-p differential swing. Pay close attention to PCB layout - separate analog and digital ground planes and place bypass capacitors as close to the supply pins as possible to achieve the published SNR and SFDR numbers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

견적 요청 문의하기
ADS5413-11IPHPG4 - 11-Bit 65MSPS High-IF ADC | Texas Instruments
ADS5413-11IPHPG4

ADS5413-11IPHPG4 - 11-Bit 65MSPS High-IF ADC | Texas Instruments

The Texas Instruments ADS5413-11IPHPG4 is an 11-bit, 65-MSPS pipelined analog-to-digital converter (ADC) optimized for high-IF and wide-bandwidth sampling, housed in a 48-pin HTQFP (PHP) 7x7 mm PowerPad package. It accepts a 2-Vpp differential analog input, operates from a 3.3-V analog supply, and supports separate digital I/O supplies from 1.8 V to 3.3 V for flexible host interface levels. Typical total power dissipation is 400 mW. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltages and converts them into discrete digital codes for downstream DSP, FPGA, or microcontroller processing. Within the signal-chain taxonomy, the ADS5413-11 belongs to the high-speed pipelined ADC family, which sits between successive-approximation-register (SAR) ADCs (low speed, high accuracy) and flash ADCs (highest speed, lowest resolution). Pipeline ADCs use multiple cascaded low-resolution stages to balance speed, resolution, and power, making them the dominant choice for communications, radar, IF-sampling, and wideband instrumentation. Key features include 11-bit resolution (the parent ADS5413 family is 12-bit; the -11 variant truncates to 11 bits), a 65 MSPS maximum sample rate, a 1.0 GHz analog input bandwidth (per parent family), on-chip sample-and-hold, duty-cycle adjust circuit for clock conditioning, two's-complement offset-binary output format, and selectable internal or external reference. The HTQFP-48 PowerPad package provides a low thermal resistance path (~28 C/W with proper PowerPad soldering), enabling continuous 65 MSPS operation without external heatsinking. The ADS5413-11 uses a multi-stage switched-capacitor pipeline architecture with digital error correction, achieving 64.5 dBFS SNR and ~80 dBcSF spurious-free dynamic range at baseband. The wide 1 GHz analog front-end permits under-sampling of IF signals up to several hundred MHz, eliminating an entire downconversion stage in transceiver designs. Typical applications include cellular base-station IF digitizers, cable-headend downstream receivers, radar and electronic-warfare intermediate-frequency sampling, medical imaging front-ends, and high-speed test-and-measurement digitizers. The 65 MSPS / 11-bit combination strikes a balance between ENOB and cost for wideband IF chains. When designing with this device, place the differential input coupling capacitors within 5 mm of the INP/INN pins and route the CLK input as a 50 ohm matched differential pair to preserve SFDR. The PowerPad must be soldered to a continuous ground plane for thermal dissipation and AC grounding. Use the duty-cycle adjust feature to compensate for non-50% clock duty cycles introduced by long clock traces. This page synthesizes distributor pricing, drop-in HTQFP-48 alternatives, and practical layout notes not consolidated on the manufacturer product page.

견적 요청 문의하기
ADS5421Y/R - 14-Bit 40MSPS Pipelined ADC | Texas Instruments
ADS5421Y/R

ADS5421Y/R - 14-Bit 40MSPS Pipelined ADC | Texas Instruments

The Texas Instruments ADS5421Y/R is a high-dynamic-range 14-bit, 40MSPS pipelined analog-to-digital converter (ADC) housed in a 64-pin LQFP (PM) package measuring 10x10 mm. It integrates a high-bandwidth linear track-and-hold amplifier, accepts fully differential or single-ended analog inputs, and consumes a typical 850 mW from a 5 V analog supply. According to the manufacturer datasheet, the converter achieves excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) performance up to and beyond the Nyquist frequency, making it suitable for high-IF sampling architectures. The selectable full-scale input range and internal references allow designers to trade noise floor against distortion for optimal dynamic range. The differential clock input accepts low-level sine or square wave signals down to 0.5 VPP, further improving SNR in noise-sensitive receive paths. A pipelined ADC such as the ADS5421Y/R is a multi-stage converter that processes the analog input through successive low-resolution flash stages, with each stage resolving a portion of the bits while a high-bandwidth track-and-hold holds the residue for the next stage. In the broader system hierarchy, pipelined ADCs sit between successive-approximation register (SAR) converters (used for low-speed, high-precision measurements) and flash ADCs (used for ultra-high-speed but low-resolution capture). The pipelined architecture enables tens-of-MSPS sampling with 10-14 bit resolution at moderate power, occupying a middle ground in the data-converter taxonomy of precision, speed, and power dissipation. As a member of the data-converter subcategory under signal chain and power management ICs, the ADS5421Y/R bridges the analog front end and the digital signal processor (DSP) or field-programmable gate array (FPGA) downstream. Key features include 14-bit resolution, 40 MSPS maximum sampling rate, 850 mW typical power dissipation, a flexible differential or single-ended clock input accepting down to 0.5 VPP levels, internal or external reference modes, selectable full-scale input range, and CMOS-compatible digital outputs. The LQFP-64 package provides 64 gull-wing leads on a 0.5 mm pitch, simplifying PCB layout and rework compared with fine-pitch ball-grid packages. The industrial operating temperature range of -40C to +85C and the absence of an automotive grade suffix in the /R designation confirm its positioning for general-purpose industrial, communications, and instrumentation designs. Typical applications include high-IF undersampling in communications receivers, medical imaging front ends such as ultrasound beamformers, high-speed instrumentation and test equipment, CCD imaging digitizers, and radar intermediate-frequency (IF) digitizers. The pipelined latency of several clock cycles must be accounted for in closed-loop servo applications but is invisible in data acquisition and receive-only signal chains. When designing with this ADC, allocate adequate PCB area for the analog and digital ground planes, place decoupling capacitors within 2-3 mm of each supply pin, and route the clock and analog inputs as controlled-impedance differential pairs to preserve the datasheet SFDR/SNR figures in production hardware.

견적 요청 문의하기
ADS5422Y/1K5 - 14-Bit 62MSPS Pipeline ADC | Texas Instruments
ADS5422Y/1K5

ADS5422Y/1K5 - 14-Bit 62MSPS Pipeline ADC | Texas Instruments

The Texas Instruments ADS5422Y/1K5 is a 14-bit, 62 MSPS pipelined analog-to-digital converter (ADC) housed in a 64-pin LQFP (10x10) package, designed for high dynamic range signal acquisition. It combines a high-bandwidth linear track-and-hold amplifier with internal selectable full-scale input ranges and accepts both differential sine and square clock signals down to 0.5 VPP. An analog-to-digital converter (ADC) is a mixed-signal semiconductor that translates continuous analog voltages into discrete digital codes, forming the bridge between the analog and digital domains in modern electronic systems. Pipeline ADCs specifically use a multi-stage architecture where each stage samples, holds, and converts a coarse sub-code, with redundancy correcting inter-stage gain/offset errors. The pipeline topology achieves excellent throughput-to-power efficiency, making it the workhorse architecture for sampling rates from a few MSPS to several hundred MSPS in applications such as communications, instrumentation, and radar. The ADS5422Y/1K5 features differential analog inputs that suppress even-order harmonic distortion and allow selectable full-scale input ranges via an internal reference. Its high spurious-free dynamic range (SFDR) and high signal-to-noise ratio (SNR) at 10 MHz input make it well suited for wideband IF sampling, while the differential clock input accepts low-level sinusoids, improving the ADC's aperture jitter tolerance. The integrated track-and-hold preserves high linearity across the Nyquist bandwidth, enabling direct sampling at IF frequencies. Architecturally, the ADS5422Y/1K5 combines a wideband linear track-and-hold front end, a multi-stage switched-capacitor pipeline core, and CMOS-compatible digital outputs. Internal bandgap references and trimming registers calibrate gain and offset on-chip, removing the need for external precision references while still allowing the user to overdrive the input common-mode for maximum SFDR optimization. Typical applications include communications receivers (GSM/EDGE/TDMA base-station IF digitizing), radar and lidar digitizers, medical imaging front ends (ultrasound beamformers), cable-headend modulators, and high-speed data-acquisition systems for test and measurement. The industrial temperature grade of -40C to +85C covers the majority of outdoor and industrial deployments. When using this ADC, allocate careful PCB routing for the analog and digital grounds as well as bypass-capacitor placement; bypassing AVDD with a 10 uF ceramic plus a 0.1 uF HF capacitor within 5 mm of each pin minimizes spurs. Ensure the encode clock source has low jitter, ideally below 0.5 ps RMS, to preserve SNR at high input frequencies. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the Texas Instruments datasheet without duplicating it.

견적 요청 문의하기
ADS5422Y/1K5G4 - 14-Bit 62MSPS Pipelined ADC | Texas Instruments
ADS5422Y/1K5G4

ADS5422Y/1K5G4 - 14-Bit 62MSPS Pipelined ADC | Texas Instruments

The Texas Instruments ADS5422Y/1K5G4 is a 14-bit, 62 MSPS pipelined analog-to-digital converter (ADC) housed in a 64-pin LQFP (10x10) package with industrial temperature grade (-40C to +85C). It features high dynamic range, a premium track-and-hold front-end with differential inputs, and a selectable full-scale input range that lets the system designer trade off signal headroom versus spurious-free dynamic range (SFDR) on a per-channel basis. A pipelined ADC is a high-speed converter architecture that processes the analog input through a cascade of low-resolution flash stages interleaved with digital-to-analog converter (DAC) residues and gain stages; the throughput is one conversion per clock cycle after pipeline latency is filled, which lets the architecture scale to tens-to-hundreds of MSPS while keeping per-stage resolution modest. Pipelined ADCs sit above successive-approximation register (SAR) ADCs in throughput and below flash ADCs in raw speed, occupying the high-speed mid-resolution tier used in communications, instrumentation, and imaging front-ends. Key features include a 62 MSPS maximum sample rate, high SFDR, high SNR at 10 MHz input, flexible clocking that accepts differential or single-ended sine or square wave clocks, and a selectable on-chip reference. The differential track-and-hold rejects common-mode noise and even-order harmonics, which is critical when the downstream signal chain includes mixers or wideband IF stages. The ADS5422 uses a multi-stage switched-capacitor pipeline with proprietary correction logic to flatten SFDR across the input bandwidth; an internal bandgap and reference buffer supply the on-chip DACs used in each pipeline stage. A 3.3 V analog supply and a 3.3 V digital supply with separate ground pins minimize substrate noise coupling between the analog input stage and the LVTTL-compatible digital outputs. Typical applications include wireless base-station IF sampling, medical imaging front-ends, CCD/cis sensor digitizers, test and measurement digitizers, and high-speed industrial process control. The industrial temperature grade and 64-LQFP footprint also suit legacy board retrofits where pin-compatible replacements are required. When designing with the ADS5422Y, place the analog input network (transformer or differential driver) within 1 cm of the input pins, decouple each supply pin with 0.1 uF plus 10 uF bulk, and tie the exposed pad to a clean analog ground pour. The output bus should be series-terminated near the ADC to suppress reflection on the LVTTL edges. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including cross-brand 14-bit / 62 MSPS pipelined ADC equivalents and same-package replacement guidance for EOL scenarios.

견적 요청 문의하기
ADS5423IPJYG3 - 14-Bit 80MSPS ADC | 52-HTQFP | Texas Instruments
ADS5423IPJYG3

ADS5423IPJYG3 - 14-Bit 80MSPS ADC | 52-HTQFP | Texas Instruments

The Texas Instruments ADS5423IPJYG3 is a 14-bit, 80 MSPS analog-to-digital converter (ADC) housed in a 52-pin HTQFP (PowerPAD) package, featuring a pin-compatible footprint with the industry-standard AD6645. It operates from a single 5 V analog supply while delivering 3.3 V CMOS-compatible digital outputs, making it straightforward to interface with modern FPGAs, ASICs, and DSPs without level shifting. An analog-to-digital converter is a semiconductor device that converts continuous-time, continuous-amplitude analog signals into discrete-time, discrete-amplitude digital codes. Pipeline ADCs such as the ADS5423IPJYG3 sit within the hierarchy of data converter ICs (ADC/DAC) under signal chain and data acquisition semiconductors, and they are widely deployed whenever wideband IF or baseband signals must be digitized at high spurious-free dynamic range. Key specifications include 74 dBc SNR and 94 dBc SFDR at 80 MSPS with a 50 MHz IF input, a 2.2 Vpp differential full-scale input range, 1.85 W total power dissipation, and an integrated input buffer that isolates the on-chip track-and-hold from disturbing the source. The on-chip reference simplifies board-level design by eliminating the need for an external ADC reference IC, and the 3.3 V CMOS outputs reduce digital I/O power and ease FPGA interfacing. Built on Texas Instruments' complementary BiCom3 bipolar process, the converter uses a multi-stage pipeline architecture with digital error correction, achieving low spurious content and excellent linearity across the industrial temperature range. The integrated input buffer presents a well-defined, low-distortion load to the upstream driver, which is critical for maintaining SFDR at high intermediate frequencies. Typical applications include cellular basestation receiver IF digitizers, software-defined radio (SDR) front-ends, medical imaging signal chains, radar and sonar intermediate-frequency sampling, and high-speed test and measurement instrumentation. Designers in communications, defense, and industrial imaging routinely select this part for wideband, multi-carrier IF sampling where high SFDR preserves signal integrity. When designing with this ADC, dedicate separate analog and digital ground planes joined at a single point near the converter, and place 20 cm thickness copper pours under the exposed PowerPAD for thermal relief. The on-chip reference requires an external decoupling capacitor; consult the manufacturer datasheet for the recommended capacitor value and pin connection before finalizing layout. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical PCB/thermal design notes that the bare manufacturer datasheet does not compile in one place, giving engineers a faster path from selection to qualified BOM.

견적 요청 문의하기
ADS5423IPJYR - 14-Bit 80MSPS ADC, HTQFP-52 | Texas Instruments
ADS5423IPJYR

ADS5423IPJYR - 14-Bit 80MSPS ADC, HTQFP-52 | Texas Instruments

The Texas Instruments ADS5423IPJYR is a 14-bit, 80-MSPS pipelined analog-to-digital converter (ADC) housed in a 52-pin HTQFP package with an exposed thermal pad. It operates from a single 5V analog supply with 3.3V CMOS-compatible outputs, and supports a 2.2 Vpp differential input range. According to the TI datasheet, it delivers 74 dBc SNR and 94 dBc SFDR at 80 MSPS with a 50 MHz IF input, while consuming only 1.85W total power. The ADS5423 is pin-compatible with the industry-standard AD6645 footprint, enabling direct drop-in upgrades in legacy designs. A pipelined ADC is a type of high-speed data converter that processes analog input signals by sampling the waveform and distributing the conversion work across a cascade of low-resolution flash stages. The 14-bit pipelined ADC sits at the intersection of precision conversion and high-speed signal acquisition, offering a compromise between multi-bit sigma-delta accuracy (which favors slow speeds) and flash converter speed (which typically sacrifices resolution). The ADS5423 is part of the ADC category hierarchy: ADC -> data converter -> signal chain IC -> analog/mixed-signal semiconductor. The architecture is built on TI's complementary bipolar BiCom3 process, which provides the high bandwidth necessary to resolve 14 bits at 80MSPS while keeping aperture jitter low. Internal references and a 2.2 Vpp differential input range simplify front-end design by removing the need for external high-precision reference voltage sources. The differential input is well suited to drive the on-chip Track-and-Hold (T/H) for clean IF sampling in communications receivers. For communications test equipment, the 14-bit/80MSPS combination provides sufficient dynamic range for narrow-band IF digitization at 70 MHz or 140 MHz, while 3.3V CMOS output levels interface directly to FPGAs and DSPs without level shifters. The HTQFP-52 package with exposed pad provides thermal performance suitable for continuous full-speed operation. The ADS5423IPJY (tape and tray) and ADS5423IPJYR (tape and reel) share the same silicon and footprint. Typical applications include cellular base-station IF digitizers, cable-headend downstream QAM receivers, medical imaging receivers, test and measurement digitizers, and radar/sonar intermediate-frequency acquisition. When designing the input network, use a 4:1 impedance-ratio balun to convert a single-ended 50Ω IF source to the 200Ω differential input the part expects, and decouple the DRVDD and AVDD pins with separate 0.1 µF ceramic capacitors placed as close as possible to the device.

견적 요청 문의하기
ADS5423IPJYRG3 - 14-Bit 80 MSPS ADC | Texas Instruments
ADS5423IPJYRG3

ADS5423IPJYRG3 - 14-Bit 80 MSPS ADC | Texas Instruments

The Texas Instruments ADS5423IPJYRG3 is a 14-bit, 80 MSPS pipelined analog-to-digital converter (ADC) that operates from a 5 V analog supply while delivering 3.3 V CMOS-compatible digital outputs. It is offered in a thermally enhanced 52-pin HTQFP PowerPAD package (10 mm x 10 mm) and provides a 2.2 Vpp differential input range with an on-chip input buffer that isolates the internal Track-and-Hold switching from the signal source. Per the TI datasheet, the converter achieves 74 dBc SNR at 80 MSPS with a 50 MHz IF input, 94 dBc SFDR under the same conditions, and dissipates roughly 1.85 W total power across the 5 V rail and the 3.3 V digital rail. An ADC is a mixed-signal integrated circuit that samples a continuous-time analog waveform and encodes each sample into a discrete digital code; the ADS5423 specifically belongs to the pipelined-architecture ADC family, which sits above successive-approximation (SAR) ADCs in conversion-speed capability and below flash converters in absolute latency. Within the broader data-converter hierarchy, pipelined ADCs like the ADS5423 are the workhorse of intermediate-frequency (IF) sampling, medical imaging basestations, and software-defined radio receivers where tens of megasamples per second with high spurious-free dynamic range are required. Key specifications include 14-bit resolution, a 1.85 W typical power dissipation, an integrated input buffer/reference, and a footprint-pin-compatible relationship to the legacy AD6645. The BiCom3 complementary bipolar process provides excellent linearity, and the device is specified across the full -40 C to +85 C industrial temperature range. Designers can optionally drive the inputs in single-ended mode via the integrated bias network, simplifying front-end design when a transformer is not available. Architecture-wise, the device uses multiple low-resolution flash stages per pipeline stage, with a final digital error-correction block that yields the 14-bit result at 80 MSPS. The digital outputs are LVCMOS-3.3 V and can directly drive an FPGA or ASIC capture FIFO without level translation, removing the need for external buffers. An internal reference generator further reduces the bill of materials by eliminating external precision reference ICs. Typical applications include communications IF-sampling receivers (cellular base stations, software-defined radio), medical imaging front-ends (ultrasound beamformers), industrial data-acquisition systems, and high-end instrumentation. When designing with this part, ensure adequate PCB thermal relief under the exposed pad - the device dissipates close to 2 W even at typical use, and the HTQFP PowerPAD must be soldered to a sufficient copper pour to remain within the industrial temperature range. This page synthesizes distributor pricing, pin-compatible family members, and practical layout guidance not found in the manufacturer datasheet alone.

견적 요청 문의하기
ADS5423MPJYEP - 14-Bit 80MSPS 5V ADC | Texas Instruments
ADS5423MPJYEP

ADS5423MPJYEP - 14-Bit 80MSPS 5V ADC | Texas Instruments

The Texas Instruments ADS5423MPJYEP is a 14-bit, 80 MSPS pipelined analog-to-digital converter (ADC) that operates from a single 5 V supply while providing 3.3 V CMOS-compatible digital outputs, housed in a 52-pin QFP (10x10 mm) package. The MPJYEP suffix denotes the enhanced-product (EP) version rated for the military/defense temperature range of -55C to +125C, with the same pinout and functional block as the standard ADS5423. Its on-chip input buffer isolates the internal track-and-hold switching transients from the analog source, eliminating the need for an external high-bandwidth front-end amplifier in many systems. What is a pipelined ADC? A pipelined analog-to-digital converter is a high-speed converter architecture that uses multiple low-resolution stages (commonly 1.5 bits per stage) operating concurrently on different samples to achieve tens to hundreds of MSPS while consuming modest power. The architecture sits in the hierarchy ADC > high-speed ADC > pipelined ADC > data-conversion IC > semiconductor; pipelined ADCs dominate mid-to-high-speed IF sampling in communications, imaging, and defense systems where 80-200 MSPS conversion is required. Key specifications of the ADS5423MPJYEP include 14-bit resolution, 80 MSPS maximum sampling rate, 70 dB SNR typical at 10 MHz input, SFDR of 80 dB, and 5 V analog / 3.3 V digital supply operation. The integrated input buffer, internal reference, and programmable full-scale range simplify board design, while LVCMOS/CMOS-compatible outputs interface directly with ASICs or DSP glue logic. The 52-QFP package is surface-mount friendly and offers a 10x10 mm footprint compatible with both industrial SMT lines and ruggedized defense assembly flows. At the architecture level, the device uses a multi-stage pipelined front-end followed by digital error correction, achieving excellent linearity (DNL/INL < 1 LSB typical) without requiring calibration. The internal reference reduces external component count, and the 3.3 V CMOS outputs avoid the need for level shifters into low-voltage FPGAs or DSPs. Typical applications include radar and EW receivers, medical imaging front-ends, communications IF sampling, baseband I/Q digitization, and high-performance industrial instrumentation. The wide temperature grade allows direct use in outdoor or vehicle-mounted defense electronics. When designing with this ADC, follow the standard high-speed ADC layout practice: solid ground planes, decoupling within 5 mm of each supply pin, controlled-impedance analog inputs, and a noise-isolated analog/digital split to achieve datasheet SFDR performance.

견적 요청 문의하기
ADS5424IPJYG3 - 14-Bit 105MSPS High-Perf ADC | Texas Instruments
ADS5424IPJYG3

ADS5424IPJYG3 - 14-Bit 105MSPS High-Perf ADC | Texas Instruments

The Texas Instruments ADS5424IPJYG3 is a 14-bit, 105-MSPS high-performance bipolar analog-to-digital converter (ADC) housed in a 52-pin HLQFP PowerPAD package. It combines a 2.2 Vpp differential input range with 5 V analog supply operation, 74 dBc SNR and 93 dBc SFDR at 105 MSPS, making it suitable for high-IF digitization in communications, defense, and test-and-measurement systems. The total power dissipation is rated at 1.9 W and CMOS-compatible outputs operate from a separate 3.3 V rail for easy interface to FPGAs and DSPs. An analog-to-digital converter (ADC) is a mixed-signal data converter that samples a continuous-time analog input voltage and produces a discrete-time digital code proportional to the input amplitude. Within the broader data-converter hierarchy, the ADS5424 belongs to the high-speed pipelined ADC family, which sits above SAR and delta-sigma converters in the sampling-rate taxonomy and is the architecture of choice for IF/RF digitization above 10 MSPS. This positioning makes it directly relevant to radar, software-defined radio, medical imaging, and high-end instrumentation front-ends. Key features of the ADS5424 include an integrated input buffer, internal reference, and a 14-bit LVCMOS-compatible parallel output bus. The device supports both single-ended and differential drive topologies, and its internal dither circuit improves small-signal linearity in the presence of coherent inputs. Differential non-linearity (DNL) is specified at +/-0.6 LSB and integral non-linearity (INL) at +/-1.5 LSB, providing engineers with the headroom needed for spectral analysis at high input frequencies. The architecture is a multi-stage switched-capacitor pipeline with on-chip sample-and-hold, error correction, and digital post-processing. This topology is responsible for the 1.9 W power figure and the 52-pin PowerPAD-enhanced QFP thermal envelope, which is required because the digital outputs and analog front-end share a common substrate. The exposed die pad (PowerPAD) must be soldered to a ground plane to maintain the published thermal resistance of approximately 22 C/W (junction-to-ambient on a 4-layer JEDEC test board). Typical applications for the ADS5424IPJYG3 include high-IF sampling in cellular base-station receivers, digital oscilloscopes and spectrum analyzers, defense radar and EW systems, and medical imaging front-ends such as ultrasound beamformers. The 105 MSPS sampling rate, combined with the 2.2 Vpp input range, also makes it a candidate for cable-headend equipment and professional video digitizers. In all of these applications, the device replaces legacy 12-bit pipelines where extra dynamic range is required without a significant cost or power penalty. When designing with the ADS5424, careful attention must be paid to the analog input network: a differential transformer drive with back-to-back clipping diodes and 50-ohm source terminations is the recommended pattern. A low-impedance ground plane directly under the PowerPAD is essential for thermal performance, and the 3.3 V digital supply should be decoupled with 0.1 uF and 10 uF capacitors placed within 5 mm of the DVDD pins. This page synthesizes distributor stock, verified drop-in alternatives, and practical design notes that are not found in the standalone manufacturer datasheet, giving engineers a single, actionable reference for the ADS5424IPJYG3.

견적 요청 문의하기
ADS5424IPJYR - 14-Bit 105MSPS ADC HTQFP-52 | Texas Instruments
ADS5424IPJYR

ADS5424IPJYR - 14-Bit 105MSPS ADC HTQFP-52 | Texas Instruments

The Texas Instruments ADS5424IPJYR is a 14-bit, 105 MSPS pipelined analog-to-digital converter (ADC) housed in a 52-pin HTQFP (PJY) powerPAD package with an integrated heatsink. It operates from a single 5V analog supply and provides 3.3V CMOS-compatible digital outputs, achieving 74 dBc SNR and 93 dBc SFDR at a 105 MSPS sample rate with an IF input. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous analog voltage waveforms into binary digital codes for downstream DSP, FPGA, or ASIC processing. Within the ADC hierarchy, the ADS5424 belongs to the pipelined sub-family, which uses a multi-stage switched-capacitor architecture to deliver tens-to-hundreds of MSPS while keeping per-stage resolution low. Pipelined ADCs sit alongside successive-approximation (SAR), delta-sigma, and flash converters as the four principal conversion architectures used in modern signal chains. Key features of the ADS5424 include a 2.2 Vpp differential full-scale input range, an on-chip input buffer that isolates the internal track-and-hold from the signal source, and 1.9 W total power dissipation. The device is built on TI's BiCom3 complementary bipolar process, which provides high spurious-free dynamic range at intermediate frequencies, and the digital outputs are LVCMOS-compatible at 3.3V for direct interface to FPGAs and ASICs without level shifters. The HTQFP-52 powerPAD package with integrated heatsink enables sustained 1.9W dissipation without external thermal management. This is critical because junction temperature directly limits SFDR performance at high IF inputs. The pinout is also designed to be pin-compatible with the AD6645 from Analog Devices, which simplifies second-source strategies for communications and defense customers who require multi-vendor sourcing of high-performance IF-sampling ADCs. Typical applications for the ADS5424 include cellular basestation receive paths, cable-headend downstream QAM digitizers, radar and electronic-warfare intermediate-frequency sampling, medical imaging front-ends such as ultrasound beamformers, and high-speed instrumentation. Its 105 MSPS rate makes it suitable for digitizing IF signals up to approximately 50 MHz while still meeting noise and linearity requirements for communications receivers. When designing with the ADS5424, designers should follow TI's recommended evaluation-module (EVM) layout and use a low-jitter clock to avoid SNR degradation, since aperture-jitter sensitivity scales with input frequency. The exposed powerPAD must be soldered to a sufficient copper pour to keep junction temperature within the -40C to +85C industrial operating range. This page synthesizes distributor pricing, application guidance, drop-in cross-vendor alternatives (including the pin-compatible AD6645), and practical design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기
ADS5424IPJYRG3 - 14-bit 105MSPS ADC HTQFP-52 | Texas Instruments
ADS5424IPJYRG3

ADS5424IPJYRG3 - 14-bit 105MSPS ADC HTQFP-52 | Texas Instruments

The Texas Instruments ADS5424IPJYRG3 is a 14-bit, 105 MSPS pipelined analog-to-digital converter housed in a 52-pin HTQFP (PowerPAD) package, designed for high-performance IF and baseband signal acquisition. The device operates from a single 5 V analog supply while delivering 3.3 V CMOS-compatible digital outputs, simplifying interface to modern FPGAs and ASICs without external level shifters. Key headline specifications are 105 MSPS maximum sample rate, 74 dBc SNR at 105 MSPS with an IF input, 93 dBc SFDR at 105 MSPS, and 2.2 Vpp differential full-scale input range with 1.9 W typical power dissipation. An analog-to-digital converter (ADC) is a data-conversion integrated circuit that samples continuous analog signals and outputs discrete digital codes proportional to the input voltage. The 14-bit pipelined ADC architecture (hypernym: ADC -> data converter -> mixed-signal IC -> semiconductor) multiplies converter resolution by cascading low-resolution flash stages and digital error correction, achieving the best trade-off among sample rate, resolution, and power consumption. The 105 MSPS rate places this part in the mid-speed IF sampling tier used in communications, radar, and industrial imaging. The ADS5424 integrates an on-chip input buffer which isolates the internal Track-and-Hold switching transients from the external signal source, easing front-end filter design. Built on Texas Instruments' complementary BiCom3 bipolar process, the converter delivers strong dynamic range at high input frequencies where many CMOS ADCs lose linearity. Differential clock and data interfaces are LVDS/CMOS-selectable to ease integration with both legacy and modern DSP/FPGA platforms. Typical applications include cellular basestation receiver IF digitizers, software-defined radio (SDR) front-ends, medical ultrasound beamformers, and industrial non-destructive test instrumentation. The wide full-scale input range and high SFDR make it equally suitable for spectrum analyzer digitizers and radar IF samplers. Per Texas Instruments, the ADS5424 is pin-compatible with the Analog Devices AD6645, simplifying second-source procurement. When designing with this part, allocate a minimum 1 oz copper ground pour under the exposed thermal pad to keep junction temperature below 125 degrees C, and place input coupling capacitors within 5 mm of the IN+/IN- pins to preserve SNR. Decouple AVDD and DVDD rails with separate 10 uF + 0.1 uF pairs and keep the encode clock trace length-matched to the duty-cycle specification in the datasheet. This page synthesizes distributor pricing, same-package drop-in alternatives including the pin-compatible AD6645, and practical PCB layout guidance not consolidated in any single manufacturer datasheet.

견적 요청 문의하기
ADS5424MPJYEP - 14-Bit 105MSPS ADC, Enhanced Product | Texas Instruments
ADS5424MPJYEP

ADS5424MPJYEP - 14-Bit 105MSPS ADC, Enhanced Product | Texas Instruments

The Texas Instruments ADS5424MPJYEP is a 14-bit, 105 MSPS pipelined analog-to-digital converter housed in a 52-pin thermally-enhanced thin quad flat pack (HTQFP) with an integrated heat sink and exposed thermal pad. It operates from a 5 V analog and digital supply, accepts single-ended or differential analog inputs, and is built on TI's complementary bipolar BiCom3 process. As an Enhanced Product (EP) variant, it is specified over the full military temperature range of -55C to +125C, making it suitable for high-reliability applications beyond commercial/industrial grades. An analog-to-digital converter (ADC) is a data-conversion integrated circuit that samples continuous analog signals and translates them into discrete binary codes for downstream digital processing. Within the converter taxonomy, the ADS5424MPJYEP sits at the sub-hierarchy: ADC -> high-speed ADC -> pipelined ADC -> 14-bit precision converter -> data acquisition IC -> semiconductor. Pipelined ADCs use a cascade of low-resolution stage ADCs, DACs, and residue amplifiers to achieve high sample rates while keeping per-stage resolution low, which is why they dominate the 10 MSPS to 500 MSPS performance tier. Key differentiating specifications include 14 bits of resolution, 105 MSPS sampling rate, 70 dB signal-to-noise ratio (SNR), 80 dB spurious-free dynamic range (SFDR), a bipolar input range centered on mid-scale, and internal bandgap reference. The pipelined architecture provides 6 clock-cycle latency, and the output data interface supports both parallel CMOS and LVDS modes for flexible downstream FPGA or ASIC capture. The integrated heat-sink HTQFP-52 package keeps theta_JA low enough for full-speed 105 MSPS operation without external cooling. Typical applications include radar receiver signal chains, software-defined radio (SDR) baseband digitizers, medical imaging front-ends (ultrasound beamformers, CT scanners), and defense electronic-warfare subsystems. Engineers favor this part where AD6645-footprint drop-in compatibility is desired, since TI documents pin compatibility with the AD6645. Industrial test and instrumentation, including digital oscilloscopes and spectrum analyzers, also use this converter family. When designing with the ADS5424MPJYEP, ensure that the analog input network provides proper 50 ohm termination and that the 5V supply is well decoupled at both the AVDD and DRVDD pins. For questions about lead-free finish, package, and lead-time contact a XAIPART representative. This page synthesizes distributor pricing, drop-in alternatives, and design context drawn from the manufacturer datasheet, the AD6645 cross-reference note, and authorized distributor listings.

견적 요청 문의하기
ADS5433IPJYG3 - 14-Bit 80 MSPS ADC, 52-Pin PQFP | Texas Instruments
ADS5433IPJYG3

ADS5433IPJYG3 - 14-Bit 80 MSPS ADC, 52-Pin PQFP | Texas Instruments

The Texas Instruments ADS5433IPJYG3 is a 14-bit, 80 MSPS pipelined analog-to-digital converter that operates from 5 V and 3.3 V supplies and produces 3.3 V CMOS-compatible digital outputs, all housed in a 52-pin PQFP package. The device delivers typical SNR of 74.4 dBc and typical SFDR of 96.5 dBc at 80 MSPS with a 30 MHz input, and is guaranteed to provide at least 91 dBc SFDR across the full operating envelope. The pipelined architecture and integrated input/output buffering make it well suited to wideband IF sampling where dynamic range and spurious-free performance directly determine receiver sensitivity. Background Knowledge: An analog-to-digital converter (ADC) is a data-conversion integrated circuit that samples continuous-time analog signals and produces discrete digital codes, typically in parallel or serial form. The hierarchy is: ADC -> data converter -> data acquisition IC -> signal chain IC -> semiconductor. Pipelined ADCs are the workhorse of medium-to-high speed applications (10 MSPS to 250 MSPS), splitting the conversion into low-resolution stages that operate concurrently, providing an excellent trade-off between sample rate, resolution, and power. Key ADC metrics include SNR (signal-to-noise ratio), SFDR (spurious-free dynamic range), ENOB (effective number of bits), aperture delay, and INL/DNL linearity. Key features of the ADS5433IPJYG3 include 14-bit resolution, 80 MSPS maximum sample rate, 74.4 dBc typical SNR at 30 MHz IF, 96.5 dBc typical SFDR at 30 MHz IF, and parallel CMOS outputs on a 52-pin PQFP package. The dual-supply topology (5 V analog, 3.3 V digital) allows the analog front-end to swing cleanly while the digital outputs interface directly to 3.3 V FPGAs, ASICs, or DSPs without level translation. The pipelined core uses switched-capacitor gain stages with a proprietary calibration routine that corrects inter-stage gain and offset errors at power-up, achieving the >91 dBc SFDR guarantee without external trimming. The differential input architecture rejects common-mode noise and harmonics from upstream drivers, while the internal reference simplifies board-level design by eliminating an external reference IC. The 3.3 V CMOS output bus is double-data-rate friendly and easily captured by modern FPGAs. Typical applications include communications receivers, radar signal processing, medical imaging front-ends, CCD digitizers, and high-speed data acquisition systems. Industrial vibration analysis and ultrasonic non-destructive testing are also common use cases that benefit from the part's wide input bandwidth and 80 MSPS throughput. When designing with this ADC, allocate analog and digital ground regions joined at a single point near the AGND/DGND pins, and place 0.1 uF bypass capacitors within 2 mm of every supply pin. The 5 V analog supply should be sourced from a low-noise LDO; do not power the analog rail from a switching converter without significant filtering. This page synthesizes verified distributor pricing, drop-in pin-compatible alternatives, application guidance, and PCB layout best practices that go beyond the bare datasheet specification table.

견적 요청 문의하기
ADS5433IPJYR - 14-Bit 80 MSPS ADC | Texas Instruments | 5V/3.3V
ADS5433IPJYR

ADS5433IPJYR - 14-Bit 80 MSPS ADC | Texas Instruments | 5V/3.3V

The Texas Instruments ADS5433IPJYR is a 14-bit, 80 MSPS analog-to-digital converter (ADC) that operates from 5 V and 3.3 V supplies while delivering 3.3 V CMOS-compatible digital outputs, housed in a 52-pin QFP package. Per the manufacturer datasheet, the device combines a high-performance track-and-hold amplifier on the front end with a pipeline converter architecture to provide wideband signal capture at 80 megasamples per second. The integrated digital output formatter and on-chip references simplify board-level design for instrumentation, imaging, and communications front ends. According to the manufacturer datasheet, the ADC supports a -40C to +85C operating temperature range suitable for industrial and commercial environments. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that samples a continuous-time analog voltage and produces a discrete-time digital code proportional to the input amplitude. ADCs sit within the data-conversion hierarchy: SAR ADC and pipeline ADC are the two dominant high-speed architectures, with pipeline ADCs favored for sample rates above ~10 MSPS where conversion speed and wide input bandwidth outweigh SAR's latency advantage. ADCs belong to the broader category of data converters, which also include DACs (digital-to-analog converters) and CODECs. The ADS5433IPJYR is a pipeline ADC optimized for applications where dynamic performance, sample rate, and wide input bandwidth are critical design parameters. Key features of the ADS5433IPJYR include 14-bit resolution, 80 MSPS maximum sample rate, 5 V analog supply, 3.3 V digital supply, and 3.3 V CMOS-compatible digital outputs that interface directly with ASICs, FPGAs, and DSP processors. The device features a maximum analog input voltage of 2.2 V and integrated reference circuitry. The wideband track-and-hold front end delivers high spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) at IF inputs, making the part well-suited for communications, radar, and test-and-measurement applications. At the architectural level, the ADS5433IPJYR uses a multi-stage pipeline with digital error correction. Each stage resolves a subset of bits and passes the residue to the next stage, producing a one- to two-cycle latency between sample acquisition and output code availability. The internal reference and sample-and-hold amplifier minimize external component count; however, careful attention to analog-input drive network and clock-jitter cleanliness is required to preserve SNR at higher input frequencies. Typical applications for the ADS5433IPJYR include communications base-station IF sampling, medical imaging front ends, CCD and CIS sensor digitizers, high-speed data acquisition cards, and radar processing subsystems. Its 52-pin QFP footprint is well-suited for production PCBs using standard SMT assembly lines. When designing with the ADS5433IPJYR, drive the analog input through a wideband differential amplifier or transformer network to maximize SFDR, and provide a low-jitter clock to the CLK input to preserve SNR. Decouple the 5 V AVDD and 3.3 V DRVDD rails independently near the device to minimize digital-to-analog coupling through the package substrate. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the ADS5433IPJYR - content not aggregated in the standalone manufacturer datasheet.

견적 요청 문의하기
ADS5433IPJYRG3 - 14-Bit 80MSPS ADC, 52-QFP | Texas Instruments
ADS5433IPJYRG3

ADS5433IPJYRG3 - 14-Bit 80MSPS ADC, 52-QFP | Texas Instruments

The Texas Instruments ADS5433IPJYRG3 is a 14-bit, 80 MSPS analog-to-digital converter (ADC) operating from +5V analog and +3.3V digital supplies while delivering 3.3V CMOS-compatible outputs, all housed in a 52-pin PowerPAD QFP (PJY) package. The integrated pipeline architecture provides single-ended conversion with internal references and an integrated analog input buffer option, achieving 69 dB SNR and 80 dB SFDR typical at 80 MSPS input. An analog-to-digital converter is a data-acquisition component that samples continuous analog signals and converts them into discrete digital codes at a defined sampling rate; pipelined ADCs like the ADS5433 family are the standard architecture for high-speed IF/RF sampling, instrumentation, and medical imaging signal chains because they balance conversion speed, dynamic range, and power consumption. As an active member of the ADC family hierarchy (pipeline ADC -> Nyquist-rate ADC -> data converter -> signal-chain IC), it supports full-power analog input bandwidths well above the Nyquist limit, enabling undersampled IF capture. Key features of the ADS5433IPJYRG3 include a user-selectable +3.0V or +3.5V internal reference, an internal input clamp for over-range protection, low 290mW typical power dissipation at 80 MSPS, parallel CMOS outputs, and a programmable full-scale range. The 52-QFP PowerPAD package supplies a low thermal resistance path for heat extraction, while the CMOS digital interface simplifies connection to ASICs and low-cost FPGAs without needing an LVDS deserializer. Architecturally, the device combines a wide-bandwidth track-and-hold, 14 pipelined quantization stages with digital error correction, and an on-chip reference generator with internal buffer. External analog-input drive is performed with low-impedance amplifiers; the inputs are fully differential to maximize second-order harmonic distortion rejection, with an optional 50 ohm matching network placed at the analog front end. The -1IN/+1IN analog input pins bond to an internal SHA. Typical applications include high-end digital oscilloscopes and digitizers, IF digitizers for communications test equipment, medical ultrasound and imaging front ends, CCD/camera-pixel acquisition pipelines, and video broadcast equipment. The internal buffer and high sample rate make it suitable for wideband instrumentation capture of transients. When designing with this converter, take care to provide a low-noise, well-decoupled analog 5V rail and a clean 3.3V digital rail. Use controlled-impedance PCB routing for analog inputs and clock, and place input termination close to the device pins to preserve SFDR.

견적 요청 문의하기
ADS5440IPFPRG4 - 13-Bit 210 MSPS Pipeline ADC | Texas Instruments
ADS5440IPFPRG4

ADS5440IPFPRG4 - 13-Bit 210 MSPS Pipeline ADC | Texas Instruments

The Texas Instruments ADS5440IPFPRG4 is a 13-bit, 210-MSPS pipeline analog-to-digital converter (ADC) that operates from a 5 V analog supply while providing LVDS-compatible digital outputs from a 3.3 V supply, housed in an 80-pin TQFP PowerPAD package (PFP). The IPFPRG4 suffix indicates a Pb-free, RoHS-compliant tape-and-reel packaging variant. Built on TI's BiCom3X complementary bipolar process, this converter delivers excellent dynamic performance for high-IF sampling applications. A pipeline ADC (pipelined analog-to-digital converter) is a type of high-speed data converter that processes analog signals through cascaded low-resolution stages, with each stage sampling and converting a portion of the signal before passing the residue to the next stage. Pipeline ADCs sit at the top of the converter hierarchy as: pipeline ADC -> ADC -> data converter -> signal chain IC -> semiconductor. They are the workhorse architecture for communications, test and measurement, and defense applications where sample rates from 100 MSPS to 500 MSPS are required. Key features include 210 MSPS maximum sample rate, 13-bit resolution, 0.0269% integral nonlinearity (INL) error, and LVDS digital outputs that minimize switching noise coupling into sensitive analog circuitry. The dual-suprail architecture (5 V analog, 3.3 V digital) is a hallmark of high-performance converters, isolating noisy digital transients from precision analog sampling. The TQFP PowerPAD package provides a thermal resistance suitable for continuous 210 MSPS operation. The ADS5440 uses a switched-capacitor pipeline architecture with internal track-and-hold, supporting input bandwidths well above Nyquist. The recommended driver configuration pairs the ADC with the THS4509 fully-differential op amp set to provide 50 ohm termination and the 2.4 V common-mode input voltage required by the ADC's input network. On-chip references and an internal reference buffer simplify external BOM. Typical applications include communications basestation receivers (multi-carrier GSM, CDMA, WCDMA, LTE), radar and electronic warfare digitizers, test and measurement instrumentation, and medical imaging front-ends. The 210 MSPS sample rate enables IF sampling of intermediate-frequency signals up to 200 MHz, eliminating downconversion stages in receiver chains. When designing with the ADS5440, follow TI's recommended input network: a differential THS4509 driver with 50-ohm source termination, 2.4 V common-mode bias, and a 100-ohm differential load on the ADC input pins. Decouple the 5 V analog and 3.3 V digital supplies with 0.1 uF and 10 uF ceramic capacitors placed within 5 mm of each supply pin. Use controlled-impedance differential routing (100 ohm differential) for the LVDS output pairs, with 100-ohm termination at the receiver. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ADS5444HFG/EM - 13-Bit 250MSPS ADC, Military Grade | Texas Instruments
ADS5444HFG/EM

ADS5444HFG/EM - 13-Bit 250MSPS ADC, Military Grade | Texas Instruments

The Texas Instruments ADS5444HFG/EM is a 13-bit, 250-MSPS, single-channel pipelined analog-to-digital converter (ADC) housed in an 84-pin ceramic CFP (HFG) package qualified to MIL-PRF-38535 QMLV Class V. Designed for defense and aerospace systems, it operates from a 5 V analog supply and provides LVDS-compatible digital outputs from a 3.3 V supply, achieving 250 MSPS with 13-bit resolution. The integrated input buffer isolates the internal track-and-hold switching from the signal source, while an internal reference generator simplifies board-level design by eliminating the need for an external reference IC. A pipelined ADC (also called a sub-ranging flash ADC) is a high-speed data converter architecture that processes the analog input through a cascade of low-resolution flash stages, each producing a partial digital estimate that is combined in a digital correction network. Pipelined ADCs dominate applications above 50 MSPS because they balance conversion speed (sample rate), resolution (bits), and silicon die area far better than full-flash architectures. Within the converter hierarchy, the ADS5444HFG/EM sits at the high-speed / military-aerospace node, between precision SAR ADCs (<5 MSPS, >16 bits) and ultra-high-speed interleaved ADCs (>1 GSPS, 6-12 bits). Key headline specifications include 250 MSPS sample rate, 13-bit resolution, 5 V analog supply operation with 3.3 V LVDS digital I/O, 2.2 Vp-p full-scale analog input, and 410 mA typical supply current. The pipelined architecture, combined with an internal track-and-hold and integrated reference, delivers deterministic latency suitable for multi-channel phase-coherent radar and EW receivers. Built-in LVDS outputs minimise EMI and board complexity in dense signal-acquisition layouts. Typical applications include radar signal processing, electronic warfare (EW) receivers, phased-array antenna digitisation, military telemetry, and high-energy physics instrumentation where radiation tolerance, hermetic packaging, and MIL-PRF-38535 Class V qualification are mandatory. The ceramic HFG package offers 84 gull-wing leads on a 40.77 x 40.77 mm body with an aluminium-nitride substrate ideal for extreme thermal and mechanical environments. When designing with this part, allocate a dedicated low-noise 5 V analog LDO and a separate 3.3 V digital LDO to maintain SNR, and route the LVDS outputs with controlled 100-ohm differential impedance. Consult the MIL-PRF-38535 Class V datasheet for derating curves, burn-in, and radiation hardness assurance (RHA) information before finalising the design. This page synthesises QMLV part numbering, drop-in alternatives, ceramic-package design notes, and verified distributor pricing - content not consolidated on the manufacturer datasheet alone.

견적 요청 문의하기
ADS5474HFG/EM - 14-bit 400-MSPS RHA ADC, 84-CFP | Texas Instruments
ADS5474HFG/EM

ADS5474HFG/EM - 14-bit 400-MSPS RHA ADC, 84-CFP | Texas Instruments

The Texas Instruments ADS5474HFG/EM is a radiation-hardness-assured (RHA), QML Class V qualified 14-bit, 400-MSPS analog-to-digital converter supplied in an 84-pin ceramic CFP (HGQFF package code) for space and defense applications. The converter operates from a 5V analog supply and a 3.3V digital supply, providing LVDS-compatible digital outputs that simplify interface to FPGAs and ASICs in high-speed signal chains. According to the manufacturer datasheet, the ADS5474HFG/EM is rated for 100-krad(Si) total ionizing dose and is one of a 12/13/14-bit family operating from 210-MSPS to 500-MSPS, making it a drop-in choice for high-resolution radar, EW, and instrumentation front ends. An ADC (Analog-to-Digital Converter) is a mixed-signal device that samples continuous-time analog waveforms and converts each sample into a discrete digital code for downstream DSP, FPGA, or processor analysis. The 14-bit pipelined ADC sits in the signal chain hierarchy between the analog front end (amplifier/filter) and the digital processor (FPGA/DSP), and it is a member of the broader data-converter family that includes successive-approximation (SAR), delta-sigma, and flash architectures. Pipelined ADCs such as the ADS5474HFG/EM are favored in high-IF and wideband radar applications because they balance sample rate, resolution, and latency better than flash ADCs and offer higher sample rates than SAR converters. Key features include a 14-bit resolution, 400 MSPS sample rate, integrated input buffer that isolates the internal track-and-hold from the source, LVDS digital outputs, and QMLV screening with 100-krad(Si) total dose rating. The on-chip input buffer removes the need for an external high-bandwidth driver in many designs, saving board area and BOM cost while improving harmonic distortion. Combined with ceramic packaging, the part supports a 25°C to 25°C commercial operating profile as listed in distributor catalogs and meets Class V qualification per MIL-PRF-38535. The ADS5474HFG/EM uses a multi-stage pipelined architecture with proprietary error correction to maintain linearity across the full 400-MSPS clock range. The architecture achieves excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) at high input frequencies, which is essential for wideband intercept receivers and pulsed-radar digitizers. The 5V/3.3V dual-rail supply scheme isolates analog and digital domains, reducing coupling noise into the sensitive sampling network. Typical applications include phased-array radar digitizers, electronic warfare (EW) receivers, space-grade satellite communication payloads, test and measurement instrumentation, and high-energy physics data acquisition. The RHA qualification and ceramic CFP package make the part specifically suitable for LEO and GEO satellite platforms and other radiation-exposed environments. When designing with this device, designers should follow impedance-matched differential clock distribution and provide a low-noise LDO on the analog 5V rail; the input buffer presents a controlled impedance but still benefits from a band-limited front-end filter. Designers should also derate sample rate against the system SNR requirement and use LVDS point-to-point routing with controlled 100-ohm differential impedance to preserve eye margin at the FPGA receiver. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical radiation-grade design notes not consolidated in the manufacturer's datasheet.

견적 요청 문의하기
ADS5481IRGC25 - 16-Bit 80MSPS ADC w/ Buffered Input | Texas Instruments
ADS5481IRGC25

ADS5481IRGC25 - 16-Bit 80MSPS ADC w/ Buffered Input | Texas Instruments

The Texas Instruments ADS5481IRGC25 is a 16-bit, 80-MSPS pipelined analog-to-digital converter (ADC) with a buffered analog input and LVDS-compatible outputs, housed in a 64-pin VQFN (RGC) package measuring 9x9 mm. It operates from a single 5 V analog supply and a 3.3 V digital supply, with an industrial temperature range of -40 C to +85 C. A pipelined ADC is a high-speed converter architecture that uses multiple low-resolution flash stages cascaded in series; each stage resolves a few bits, then passes the residue to the next stage, producing N bits of resolution at sample rates from tens of MSPS to hundreds of MSPS. The ADS5481 belongs to the broader data-converter (ADC/DAC) IC family, which sits within the signal-chain category of mixed-signal semiconductors. Key features include 16-bit resolution at 80 MSPS, an internal high-impedance analog input buffer that eases front-end driver design, LVDS digital outputs for low-noise data transfer, and excellent SFDR (spurious-free dynamic range) for wideband IF-sampling and baseband digitisation. The buffered input removes the kickback and settling issues typically associated with switched-capacitor ADC inputs, allowing operation behind higher-impedance filter networks. The converter uses a multi-stage differential pipeline with proprietary calibration to achieve low distortion and stable performance across the industrial temperature range. The internal buffer and reference-voltage circuitry reduce the external component count, simplifying board layout for high-density designs. Typical applications include communications receivers, radar and electronic-warfare signal processing, test and measurement instrumentation, medical imaging front ends, and high-speed data acquisition systems where both wide bandwidth and high spurious-free dynamic range are required. When designing with this part, pay close attention to LVDS bus length matching, decoupling on both 5 V and 3.3 V rails, and the analog-input network. Because the input is buffered, anti-alias filter design is more forgiving than with unbuffered switched-capacitor ADCs. This page synthesises distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing an information-gain summary aimed at engineers evaluating the ADS5481IRGC25 for new designs or legacy second-source qualification.

견적 요청 문의하기