집적 회로

DSPIC33CK256MP608-E/PT

dsPIC33CK256MP608-E/PT - 100MIPS DSC, 256KB Flash, CAN FD | Microchip

The Microchip Technology dsPIC33CK256MP608-E/PT is a 16-bit digital signal controller (DSC) with a single dsPIC33CK core running at 100 MHz (100 MIPS), 256 KB of dual-panel Flash memory, and 64 KB of RAM, housed in an 80-pin TQFP (12 x 12 mm) package with extended temperature range (-40C to +125C). A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control architecture of a microcontroller. Within the power-management hierarchy, DSCs sit between general-purpose MCUs and dedicated DSPs, making them the preferred device class for closed-loop control systems that need fast math (MAC, divide, barrel shifter) plus rich analog and timing peripherals on one chip. Key features of this part include CAN FD for automotive and industrial networking, integrated operational amplifiers that reduce external BOM cost for current-sense front-ends, and 12-bit ADCs for precision feedback. The dual-panel Flash architecture supports live firmware updates, and the family carries Functional Safety (FuSa) support documentation. Per Microchip's product page, the dsPIC33CK family targets high-performance, precision motor-control systems. Technically, the single-core dsPIC33C engine executes most instructions in one cycle at 100 MIPS, while high-resolution PWM peripherals generate industry-leading edge resolutions for power conversion and motor drive. The -E suffix denotes extended operation to +125C and the part is AEC-Q100 qualified, per distributor listings. Typical applications include PMSM and BLDC motor control, digital power supplies (totem-pole PFC, LLC), automotive auxiliaries, and industrial inverters where CAN FD connectivity and deterministic PWM are mandatory. Design consideration: budget the 64 KB RAM carefully - the DMA and ADC subsystems can consume significant share space in high-sampling-rate control loops. This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4.25 재고 있음

DSPIC33CK32MP505-I/M4

dsPIC33CK32MP505-I/M4 - 100MHz 16-bit DSC CAN-FD | Microchip

The Microchip Technology DSPIC33CK32MP505-I/M4 is a 100 MHz single-core 16-bit digital signal controller (DSC) with 32 KB dual-partition Flash, 8 KB SRAM, CAN FD, integrated op-amps, and 12-bit ADCs, housed in a 48-pin UQFN with exposed pad (M4) package. It belongs to the dsPIC33CK MP family of digital signal controllers, a product class that combines the deterministic control of a 16-bit MCU with DSP-grade math acceleration for embedded control loops. A DSC sits between a general-purpose microcontroller and a dedicated DSP in the control-silicon hierarchy, adding cycle-efficient MAC and DSP instructions plus precision mixed-signal peripherals targeted at closed-loop power conversion. Key differentiating features include the 100 MHz dsPIC33CK core delivering up to 100 MIPS, ECC-protected dual-partition program Flash enabling Live Update firmware overwrite, high-resolution PWM outputs with nanosecond-scale duty resolution, and an on-chip 12-bit ADC pipeline sized for multi-channel current and voltage sampling in fast control loops. The integrated operational amplifiers reduce external component count in current-sense front ends, and CAN FD provides the higher payload and faster data phases required by modern industrial and automotive networks. Architecturally, the device uses a modified Harvard architecture with a single core, hardware DSP engine, and Memory Built-In Self-Test (MBIST) on the 8 KB SRAM. The 32 KB Flash uses error-correction coding (ECC) for functional-safety-oriented designs, and the dual-panel organization allows safe in-field firmware updates. Typical applications include digital power supplies (totem-pole PFC, LLC converters), brushless DC and PMSM motor control, DC-DC and wireless-charging stages, and advanced sensing nodes where the ADC, op-amps, and high-resolution PWM close tight analog control loops. For design, budget the 3.0V to 3.6V supply domain carefully and use the multiple VDD/VSS pairs with 100 nF decoupling per pair; route the exposed thermal pad to a ground pour for thermal and signal-integrity benefits. This page synthesizes distributor inventory data, drop-in family alternatives, pinout guidance, and practical design notes not consolidated in the manufacturer datasheet.

USD $3.78 재고 있음

DSPIC33CK64MP205-E/PT

dsPIC33CK64MP205-E/PT - 16-bit 100MHz DSC 64KB Flash | Microchip

The Microchip Technology dsPIC33CK64MP205-E/PT is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB of flash program memory and 8 KB of RAM, housed in a 48-pin TQFP (7x7 mm) package. The -E/PT suffix denotes the extended temperature range (-40C to +125C) in a thin quad flat pack with Tape & Reel delivery. A digital signal controller combines the compute architecture of a microcontroller with DSP-engine features such as single-cycle MAC, hardware divide and DSP addressing modes. Within the power-management hierarchy, DSCs sit between general-purpose MCUs and dedicated DSPs, making them the preferred choice when a control loop must execute fast, deterministic algorithms such as current-loop compensation or power-factor correction. Key features of the dsPIC33CK64MP205 include the 100 MHz dsPIC33CK CPU core, up to 33 DMIPS performance, high-resolution PWM outputs with nanosecond-class edge resolution for switching converters, CAN Flexible Data (CAN FD) support, three on-chip analog comparators, three operational amplifiers and a 12-bit ADC enabling true concurrent multi-channel sampling for digital power feedback loops. Architecturally, the dsPIC33CK family doubles the performance of the previous dsPIC33EP generation by executing most instructions in a single cycle at 100 MHz, with a zero-wait-state flash accelerator and a direct memory access (DMA) controller that offloads the CPU during high-rate ADC and PWM transactions. The on-board operational amplifiers can be used as front-end gain stages for current shunt sensing, reducing external component count in motor-drive designs. Typical applications include digital switch-mode power supplies (LLC, buck, boost, PFC), brushless DC and PMSM motor control, solar micro-inverters, battery chargers, and high-performance embedded sensing. The extended temperature grade makes the part suitable for industrial drives and automotive-adjacent environments operating up to +125C ambient. Design consideration: the 48-pin TQFP exposes a shared power/analog pin budget - plan a solid ground plane, place 100 nF decoupling on each VDD pin, and follow Microchip's digital power reference designs for ADC-PWM synchronization to achieve deterministic control-loop timing. This page synthesizes distributor pricing (as of 2026-09-23), pin-compatible family alternatives, application notes and design guidance not consolidated in the manufacturer datasheet.

USD $1.75 재고 있음

DSPIC33EP128GM310T-I/BG

dsPIC33EP128GM310T-I/BG - 70 MIPS DSC, 128KB Flash | Microchip

The Microchip Technology dsPIC33EP128GM310T-I/BG is a 16-bit digital signal controller (DSC) with a 70 MIPS dsPIC33E core, 128KB (43K x 24) Flash memory, 16KB RAM, and a 121-ball TFBGA (10x10 mm) package. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control architecture of a microcontroller. Within the embedded hierarchy, the dsPIC33E family sits above general-purpose 8-bit MCUs and alongside 16-bit MCUs, targeting real-time closed-loop control where multiply-accumulate (MAC) DSP instructions execute deterministic control loops such as field-oriented motor control and digital power conversion. Key features include the 70 MIPS dsPIC33E core with integrated DSP engine, 12-channel motor control PWM (MCPWM), 8 input capture and 8 output compare channels, 2 quadrature encoder interfaces (QEI), 4 on-chip operational amplifiers, a Charge Time Measurement Unit (CTMU), and a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. The integrated op-amps can amplify low-level current-shunt signals internally, reducing external component count in motor control and power-conversion front ends. Architecturally, the device operates from 3V to 3.6V over an industrial temperature range of -40C to +85C, executing from zero-wait-state Flash with DSP-class addressing modes. The large peripheral set is serviced by DMA and flexible interrupt prioritization, keeping CPU bandwidth free for control algorithms. Enhanced peripherals such as the PTG allow trigger sequences without CPU intervention, a significant benefit in tightly timed switching applications. Typical applications include precision BLDC and PMSM motor drives, digital power supplies (LLC, totem-pole PFC), industrial automation sensors, and embedded data-acquisition systems that benefit from the 12-channel MCPWM and on-chip analog amplification. When designing with the 121-TFBGA package, ball-map signal planning and power-ball allocation deserve early attention; the fine-pitch BGA requires controlled-impedance PCB fabrication and X-ray inspection capability for rework. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $5.05 재고 있음

DSPIC33EP128GS708-I/PT

dsPIC33EP128GS708-I/PT - 70 MIPS Digital Power DSC | Microchip

The Microchip Technology dsPIC33EP128GS708-I/PT is a 16-bit Digital Signal Controller (DSC) delivering 70 MIPS performance with 128 KB of Flash memory and 8 KB of RAM, housed in an 80-pin TQFP (12x12 mm) package rated for -40C to +85C operation. A Digital Signal Controller combines the computational throughput of a DSP with the peripheral integration and deterministic control of a microcontroller, sitting between a general-purpose MCU and a dedicated DSP in the power-management hierarchy. The dsPIC33EP GS family is purpose-built for digital switch-mode power supplies (SMPS) and digital power conversion, where fast control loops such as voltage-mode, current-mode, and multi-loop PFC require deterministic interrupt latency and high-resolution PWM. Key features include the 70 MIPS dsPIC DSC core with DSP multiply-accumulate instructions, dual 12-bit ADCs with simultaneous sampling for sensing input and output rails, high-speed PWM peripherals with dead-time control and fault protection, and integrated analog comparators for cycle-by-cycle current limiting. These peripherals enable closing of control loops at switching frequencies well above 100 kHz with software or hardware-assisted regulation. The GS-series architecture is optimized for digital power: the PWM module supports complementary, push-pull, and phase-shifted topologies, while the ADC can be synchronized directly to PWM events to sample currents at the correct instant in each switching cycle. On-chip flash supports self-programming for firmware-updatable power supplies and field firmware updates in deployed products. Typical applications include AC-DC power supplies, DC-DC converters, power factor correction stages, solar micro-inverters, battery chargers, LED drivers, and uninterrupted power supplies (UPS), where programmability replaces hard-wired analog control for flexibility and smart-grid features. Design consideration: this is a 3.0V to 3.6V device; do not power it from a 5V rail. Decouple the 3.3V supply with 0.1 uF ceramics at every VDD pin and keep the PWM-to-MOSFET-gate traces short to limit ringing and EMI. This page adds value beyond the datasheet by consolidating distributor pricing, pin-compatible drop-in family alternatives, comparison tables, and practical digital-power design notes in one place.

USD $8.80 재고 있음

DSPIC33EP128MU206-H/MR

dsPIC33EP128MU206-H/MR - 16-bit DSC 128KB Flash QFN-64 | Microchip

The Microchip Technology dsPIC33EP128MU206-H/MR is a 16-bit Digital Signal Controller (DSC) delivering up to 70 MIPS from 128 KB of flash program memory and 16 KB of RAM, integrated with a 12-bit ADC, in a 64-pin QFN (MR) package rated for -40C to +125C operation. A Digital Signal Controller combines the compute throughput of a DSP with the peripheral set and ease of use of a microcontroller. Within the power management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs: it executes single-cycle MAC and DSP-enhanced instructions like a DSP, while retaining flash self-programming, rich timers, and communication peripherals typical of microcontrollers. The dsPIC33EP family is Microchip's high-performance 16-bit DSC generation, superseding the dsPIC33F series. Key features include the 16-bit modified Harvard architecture with DSP engine, 128 KB flash and 16 KB RAM, a high-speed 12-bit ADC with multi-sample support, dual CAN 2.0B modules, USB 2.0 full-speed device capability, and multiple UART/SPI/I2C ports. The MU206 variant is distinguished by its USB and dual-CAN combination, which few other 64-pin dsPIC33EP parts offer, making it a natural fit for automotive and industrial gateway nodes. Internally, the core achieves 70 MIPS at 3.3V with a 17-bit x 17-bit single-cycle hardware multiplier, 40-bit accumulator, and dual operands addressing for DSP kernels such as FIR filters and PID loops. Programmable PLL clocking allows low-cost crystals to synthesize the full-speed system clock. Typical applications include motor control and power conversion, automotive gateways, USB-equipped industrial instruments, and digital power supplies where the 12-bit ADC feeds control loops at kHz rates. For design, the -H/MR temperature grade (-40C to +125C) and thermally enhanced QFN exposed pad demand a solid ground pour; verify clock and PLL settings against the target MIPS before finalizing layout. This page consolidates distributor sourcing data, drop-in family alternatives, and practical design notes beyond the manufacturer datasheet.

견적 요청 재고 있음

DSPIC33EP128MU504-I/ML

dsPIC33EP128MU504-I/ML - 16-bit DSC 70 MIPS 128KB Flash | Microchip

The Microchip Technology DSPIC33EP128MU504-I/ML is a 16-bit digital signal controller (DSC) delivering 70 MIPS performance with 128 KB of Flash memory and 16 KB of RAM, housed in a 44-pin QFN (ML) surface-mount package rated from -40C to +85C. A digital signal controller combines the computational strengths of a microcontroller with the math-acceleration of a digital signal processor. In the embedded hierarchy, the DSC sits above general-purpose MCUs and below full DSPs, offering single-cycle MAC, DSP multiply/divide, and divide instructions while retaining microcontroller-style peripherals, interrupt architecture, and flash self-programming. This makes DSCs the default choice for real-time closed-loop control systems. Key features of the dsPIC33EP128MU504 include the enhanced dsPIC33E core running at up to 70 MIPS from a 3.0 V to 3.6 V supply, a 12-bit ADC, UART, SPI, and I2C communication peripherals, and DSP engine support for FIR/IIR filtering and transform math. The 128 KB self-programmable Flash supports field firmware updates, and the 16 KB RAM provides headroom for control loops and communication buffers. Architecturally, the dsPIC33E family pairs a pipelined 16-bit CPU with an integrated DSP engine (a 17-bit x 17-bit multiplier, 40-bit accumulator, and barrel shifter), enabling precision motor control, digital power conversion, and sensor signal processing in a single chip. Two on-chip PLLs allow flexible clocking and low-power operation. Typical applications include brushless DC and PMSM motor control, digital power supplies (PFC, LLC), solar inverters, sensor fusion and industrial sensing nodes, and audio or biomedical signal processing. Design consideration: keep the 3.3 V supply within the 3.0 V to 3.6 V range, decouple VDD/VSS pairs with 0.1 uF ceramics placed directly at the QFN pins, and use the exposed pad for a solid ground connection. This page synthesizes distributor availability, drop-in alternative analysis, and practical design notes beyond what the manufacturer datasheet provides.

USD $3.58 재고 있음

DSPIC33EP16GS504T-E/ML

dsPIC33EP16GS504T-E/ML - 16-Bit 60 MIPS DSC 16KB Flash QFN-44 | Microchip

The Microchip dsPIC33EP16GS504T-E/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP16GS504 family, delivering up to 60 MIPS performance with 16KB (16K x 8) of FLASH program memory, housed in a 44-pin QFN (8x8 mm, ML) surface-mount package. The device is qualified for automotive use (AEC-Q100) and supports Functional Safety (FuSa) development. A digital signal controller combines the compute capability of a 16-bit digital signal processor with the peripheral integration and control peripherals of a microcontroller, sitting in the product hierarchy between a general-purpose MCU and a dedicated DSP. In the digital power ecosystem, a DSC executes the control loops of switch-mode power supplies, replacing analog control ICs with programmable firmware while retaining hard real-time response. Key features of the dsPIC33EP GS family include dedicated high-speed PWM modules purpose-built for switch-mode power supply (SMPS) topologies, on-chip high-speed ADCs for current and voltage feedback sampling, DSP-engine multiply-accumulate instructions for digital control loop math, and internal fast RC oscillators. The GS50x sub-family is explicitly marketed by Microchip for digital power conversion such as AC-DC and DC-DC power supplies. The 60 MIPS core executes the control loop at switching frequencies typical of modern SMPS designs, while the dedicated PWM peripherals offer complementary, edge-aligned and center-aligned modes with dead-time insertion - critical for half-bridge, full-bridge and LLC converters. The 16KB FLASH supports compact, deterministic control firmware; the -40C to +125C extended temperature grade (E suffix) suits automotive and industrial environments. Typical applications include interleaved power factor correction (PFC), AC-DC power supplies, DC-DC converters, digital lighting ballasts, battery chargers and solar micro-inverters. Microchip publishes an interleaved PFC reference design for this family operating from universal input voltage up to 350W output. Design consideration: budget FLASH carefully - at 16KB, avoid linking large middleware stacks and prefer hand-optimized assembly or compiler-optimized control-loop routines; verify per-pin mapping against the 44-QFN datasheet pin diagrams before layout. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $2.55 재고 있음

DSPIC33EP256MU814T-I/PH

dsPIC33EP256MU814T-I/PH - 256KB Flash 60MHz DSC 144-TQFP | Microchip

The Microchip Technology dsPIC33EP256MU814T-I/PH is a 16-bit digital signal controller (DSC) with 256 KB flash, 28 KB SRAM, and a 60 MHz dsPIC33E core, housed in a 144-pin TQFP (16x16 mm, PH) surface-mount package. A digital signal controller combines the compute power of a DSP with the peripheral integration and control-oriented architecture of a microcontroller. Within the power-management hierarchy, a DSC is a superset of a general-purpose 16-bit MCU: it adds single-cycle MAC, barrel shifter, and hardware division suited to control-loop mathematics, placing dsPIC33 devices between classic MCUs and full DSPs in embedded system design. Key features include up to 70 MIPS core performance (60 MHz clock), dual CAN modules, integrated full-speed USB, high-speed PWM peripherals for motor control, and 51 I/O ports across multiple ports. The MU subfamily is specifically positioned for motor control and digital power applications, with 27 general purpose timers available on larger family members. Architecturally, the dsPIC33E core pairs a 16-bit modified Harvard pipeline with DSP engine enhancements, supporting deterministic real-time execution of FOC (field-oriented control) and other math-intensive algorithms. Flash program memory of 256 KB (85.5K x 24 words) provides ample space for complex control firmware and communication stacks. Typical applications include dual motor control systems (BLDC, PMSM, ACIM), industrial automation nodes, and USB-connected sensing instruments that benefit from dual CAN and USB connectivity in one die. When designing with this part, respect the 3V to 3.6V supply window and plan decoupling for the multiple VDD/VSS pairs of the 144-TQFP; the industrial temperature grade covers -40C to +85C, so verify thermal margin if the 60 MHz core runs at sustained high load. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $7.89 재고 있음

DSPIC33EP32GS505T-I/PT

dsPIC33EP32GS505T-I/PT - 16-bit 70MIPS DSC 32KB Flash | Microchip

The Microchip Technology dsPIC33EP32GS505T-I/PT is a 16-bit digital signal controller (DSC) combining a dsPIC33EP RISC core running at up to 70 MIPS with 32 KB of Flash program memory, supplied at 3.0 V to 3.6 V and housed in a 48-pin TQFP with exposed pad (7x7 mm) package. A digital signal controller is a hybrid device class that merges the computational throughput of a digital signal processor with the peripheral integration, interrupt architecture and ease of use of a microcontroller. Within the power management hierarchy, the DSC sits at the top: general-purpose MCU first, DSP-enhanced MCU second, and purpose-built digital power DSC third. The dsPIC33EP GS (SMPS) family is Microchip's third tier, purpose-built for switch-mode power conversion. Key features include a modified Harvard 16-bit DSP core with single-cycle MAC and 40-bit accumulator, high-resolution PWM peripherals suited to power topologies, 12-bit ADC hardware tailored for current-mode control loops, and industrial temperature rating of -40C to +85C for the /I grade. The tape-and-reel /PT suffix indicates automatic-assembly packaging for volume production. Architecturally, the GS505 integrates dedicated digital power peripherals that offload time-critical PWM and ADC triggering from software, allowing control-loop latencies and duty-cycle update resolution to meet the demands of peak-current-mode and voltage-mode SMPS designs. Typical applications include digital power supplies, interleaved power factor correction (the Microchip 350 W universal-input interleaved PFC reference design is based on this family), DC-DC converters, battery chargers, and digital lighting ballasts. When designing with this device, budget the 3.0 V to 3.6 V supply rail carefully and verify that PWM dead-time insertion and ADC sampling timing are configured per the dsPIC33EP GS family reference manual for the chosen control topology. This page synthesizes distributor pricing context, drop-in alternatives within the same 48-pin TQFP footprint, and practical design notes not consolidated in the manufacturer datasheet.

USD $3.30 재고 있음

dsPIC33EP512GM306-I/PT

dsPIC33EP512GM306-I/PT - 70 MIPS DSC, 512KB Flash, 64-TQFP | Microchip

The Microchip dsPIC33EP512GM306-I/PT is a 16-bit Digital Signal Controller (DSC) from the dsPIC33E family, delivering up to 70 MIPS through a 140 MHz dsPIC DSC core with integrated single-cycle MAC DSP engine, packaged in a 64-pin TQFP (10x10 mm) and supplied in 3.0 V to 3.6 V industrial-grade temperature range (-40C to +85C). It integrates 512 KB of Flash program memory, 48 KB of SRAM, and on-chip peripherals tuned for high-performance precision motor control, digital power conversion, and advanced sensor processing. A Digital Signal Controller (DSC) is a hybrid class of microcontroller that combines a deterministic MCU control pipeline with a hardware DSP multiply-accumulate (MAC) engine. In the taxonomy, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP); it executes control code C-friendly while accelerating math-heavy signal processing kernels such as Field Oriented Control (FOC), digital PID, and FFT. The dsPIC33EP 'GM' sub-family is specifically designed for motor control and digital power, integrating up to four op-amps, multiple PWMs with dead-time control, and high-speed 10/12-bit ADCs. Key features of the dsPIC33EP512GM306-I/PT include twelve PWM channels with flexible triggering, eight 16-bit timers, four on-chip op-amps for current sensing in motor feedback loops, two 12-bit ADCs with up to 16 simultaneous sample-and-hold channels reaching 3.25 MSPS, and dual comparators. The device also integrates a Charge Time Measurement Unit (CTMU) for touch and capacitive sensing, a 16-bit Peripheral Pin Select (PPS) I/O remapping engine, and multiple UART/SPI/I2C/CAN interfaces. Its 16-channel DMA controller offloads data movement for deterministic, low-latency control loops. Architecture is built on a 16-bit modified Harvard bus with separate program and data paths and a hardware DSP engine. With a 140 MHz CPU clock (70 MIPS), the MAC unit executes single-cycle 16x16-bit multiplies with 40-bit accumulator, ideal for high-bandwidth control loops in PMSM/BLDC drives and power conversion. The integrated op-amps and comparators form the feedback analog front-end, eliminating an external current-sense amplifier chain and improving noise immunity. Typical applications include field-oriented control of PMSM and BLDC motors (drone ESCs, EV traction, HVAC compressors), digital power stage control for AC/DC and DC/DC converters, solar micro-inverters, servo drives, industrial automation controllers, sensorless motor control using BEMF or shunt-based observers, and high-speed signal acquisition front-ends. Audio and ultrasonic sensing are also enabled by the dual-ADC simultaneous sampling and the DSP MAC. When designing with this device, allocate the 64-pin budget between motor power signals (PWM H/L pairs, gate-driver EN lines), analog feedback (current shunts, BEMF dividers routed through the on-chip op-amps), and communication (CAN, UART, I2C for sensors and host MCU). Decouple VDD/VSS pairs as documented in the family datasheet; route AVDD separately from DVDD to keep ADC noise below 1 LSB. A JTAG/ICSP header is recommended for in-circuit debugging using MPLAB X IDE. This page synthesizes distributor pricing, drop-in design options, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate the dsPIC33EP512GM306-I/PT for next-generation motor-control and digital-power designs.

USD $7.18 재고 있음

DSPIC33EP512GP504-E/TL

dsPIC33EP512GP504-E/TL - 512KB 16-bit DSC 60MHz | Microchip

The Microchip Technology dsPIC33EP512GP504-E/TL is a 16-bit digital signal controller (DSC) with 512KB flash, 48KB RAM, a 60 MHz core, and a 44-pin VFTLA (TQFP-44) package with exposed pad, rated for -40C to +125C operation under AEC-Q100. A digital signal controller combines the computational architecture of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller (MCU). DSCs occupy the mid-tier of the embedded processing hierarchy - above general-purpose microcontrollers in math throughput, below application processors - making them the standard choice for closed-loop motor control, digital power conversion, and sensor signal processing where deterministic interrupt latency and hardware multiply-accumulate (MAC) units matter. Key features of this part include the dsPIC33E 16-bit core running at up to 70 MIPS class performance with DSP instruction support, 512KB of self-programmable flash and 48KB of on-chip RAM, and an integrated analog suite: multiple on-chip operational amplifiers, comparators, a CTMU (Charge Time Measurement Unit), and a high-performance 10/12-bit ADC. Communication coverage is broad, with CAN 2.0B, multiple UARTs, SPI, and I2C interfaces, plus the Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. The high-speed PWM module with advanced analog integration positions the device squarely in digital power and motor-control designs, while the op amps reduce external component count in current-sense signal chains. Code density from the enhanced 16-bit architecture allows complex control loops to be written largely in C with assembly-level inner loops where needed. Typical applications include brushless DC (BLDC) and PMSM motor drives, digital SMPS and power-factor-correction converters, automotive body and powertrain auxiliary systems (leveraging the AEC-Q100 -E extended temperature grade), and industrial control nodes that need CAN connectivity plus on-chip analog. Design consideration: supply the core from the internal regulator using the required low-ESR VCAP capacitor per the Microchip datasheet, and budget the 3.3V I/O rail separately; the exposed pad on the VFTLA package should be soldered to a grounded copper pour for best thermal and EMC margins. This page synthesizes distributor inventory data, same-family drop-in alternatives, and practical design guidance beyond what the manufacturer product page provides.

USD $5.20 재고 있음

DSPIC33EP64GS505-E/PT

dsPIC33EP64GS505-E/PT - 16-bit 70 MIPS DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GS505-E/PT is a 16-bit digital signal controller (DSC) delivering 70 MIPS performance with 64KB of Flash program memory, housed in a 48-pin TQFP (PT) package with exposed pad and extended temperature range of -40C to +125C. A digital signal controller combines the compute throughput of a digital signal processor (DSP) with the peripheral integration and deterministic control of a microcontroller (MCU). Within the power-management hierarchy, DSCs sit at the heart of digital switch-mode power supplies (SMPS), replacing analog control loops with firmware-based control for higher flexibility, programmability, and telemetry. The dsPIC33EP family occupies the 16-bit embedded control segment between general-purpose MCUs and 32-bit application processors. Key features of the GS50x family include an interconnected high-speed PWM module purpose-built for power conversion, high-speed analog-to-digital converters, on-chip digital-to-analog converters (DAC), programmable gain amplifiers (PGA), and analog comparators that close control loops without external components. According to Microchip, the dsPIC33EPXXGS50X family is explicitly targeted at digital power applications. Architecturally, the device uses the enhanced dsPIC33E core with DSP instruction support, allowing single-cycle MAC operations used in proportional-integral-derivative (PID) and compensator routines. The interconnected PWM, ADC, and comparator fabric enables loop latencies measured in nanoseconds, critical for peak-current-mode and multi-loop converters. Typical applications include AC-DC converters, power factor correction (PFC) stages, DC-DC converters, uninterruptible power supplies, solar micro-inverters, and lighting ballasts. The extended -40C to +125C operating range of the E-grade part suits industrial and automotive-adjacent environments. Design consideration: budget ADC sampling and PWM update timing so the control loop executes within one switching period; use the family reference design (Interleaved PFC, 350W) as a validated starting point. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3.45 재고 있음

DSPIC33EP64GS505T-E/PT

dsPIC33EP64GS505T-E/PT - 16-bit 70 MIPS DSC 64KB Flash | Microchip

The Microchip Technology dsPIC33EP64GS505T-E/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP GS series for SMPS and digital power conversion, delivering up to 70 MIPS performance with 64KB (64K x 8) of Flash program memory, packaged in a 48-pin TQFP with exposed pad (7x7 mm), and qualified to AEC-Q100 for automotive use with an extended -40C to +125C operating range. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control architecture of a microcontroller. Within the power-management semiconductor hierarchy, a DSC sits between a general-purpose MCU and a dedicated power-conversion ASIC, providing real-time loop closure for switch-mode power supplies. The dsPIC33EPXXGS50X family is specifically architected for multi-loop digital SMPS topologies. Key differentiating features include high-speed PWM modules purpose-built for power conversion, high-speed analog-to-digital converters with an integrated programmable gain amplifier (PGA), on-chip comparators, and an interconnect fabric that ties the PWM, ADC and comparator blocks together for deterministic control-loop latency. The GS50x family also carries Functional Safety (FuSa) support documentation, enabling use in safety-conscious designs. Architecturally, the device is built on the 16-bit dsPIC33EP core with DSP instruction extensions (MAC, DSP multiply), executing from zero-wait-state Flash at full speed. The interconnected high-speed PWM supports complementary outputs, dead-time control and fault protection essential for AC-to-DC, DC-to-DC, power factor correction (PFC) and inverter stages. Typical applications include AC-DC power supplies, digital PFC stages, DC-DC converters, solar micro-inverters, LED drivers and battery chargers, where the combination of fast ADC sampling and high-resolution PWM directly improves loop bandwidth and efficiency. Design consideration: the exposed-pad TQFP requires a solid ground connection to the PCB thermal pad for both heat dissipation and analog ground integrity - do not leave the ePad floating. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, as of 2026-09-25.

USD $3.38 재고 있음

DSPIC33EV256GM106T-I/PT

dsPIC33EV256GM106T-I/PT - 16-bit 70 MIPS 5V DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33EV256GM106T-I/PT is a 16-bit digital signal controller (DSC) with a 5V, 70 MIPS dsPIC33EV core, 256KB (85.5K x 24) ECC Flash program memory and 16KB SRAM, housed in a 64-pin TQFP (10x10 mm) surface-mount package with industrial temperature rating (-40C to +85C). A digital signal controller combines the control peripherals of a microcontroller with the math capabilities of a digital signal processor. Within the power-management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes real-time control loops (PID, field-oriented control) while managing communication, sensing and sequencing tasks. The dsPIC33EV family from Microchip Technology is a 5V-tolerant branch of this DSC class, which removes external level-shifting in industrial and automotive rails that still run at 5V. Key features include the 70 MIPS modified Harvard DSP core with DSP engine, barrel shifter and 40-bit accumulators, ECC-protected Flash for functional-safety designs, integrated op amps, high-resolution PWM with complementary outputs, SENT peripheral for automotive sensor interfaces, and multiple UART, SPI, I2C, QEI, CAN and DMA channels. The 5V operation distinguishes it from 3.3V MCUs, improving noise margins in harsh electrical environments. Technically, the dsPIC33EV256GM106 executes most instructions in a single cycle at up to 70 MIPS, with hardware multiply-accumulate supporting fixed-point filtering and motor-control mathematics. The Flash is specified for 85.5K x 24-bit instruction words with ECC, and code execution is deterministic without cache. Peripheral pin-select allows flexible remapping of digital functions across the 53 I/O pins. Typical applications include brushless DC and PMSM motor control in appliances, automotive body and powertrain subsystems, industrial sensors, power supplies and digital lighting. The built-in op amps and high-resolution PWM reduce external component count in sensor and power-conversion designs. Design consideration: at 70 MIPS in a 10x10 mm TQFP, ensure solid ground and power distribution with multiple VDD/VSS pairs decoupled by 0.1 uF ceramics, and verify 5V signal integrity on high-speed communication lines. This page synthesizes distributor inventory data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 재고 있음

DSPIC33EV64GM002-E/SO

dsPIC33EV64GM002-E/SO - 16-bit 5V 70 MIPS DSC | Microchip

The Microchip Technology DSPIC33EV64GM002-E/SO is a 16-bit digital signal controller (DSC) combining a 70 MIPS dsPIC33E core with 64KB of ECC-protected Flash program memory and 8KB of RAM, supplied in a 28-pin SOIC package rated for the extended -40C to +125C temperature range. A digital signal controller is a hybrid device that merges the computational architecture of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller (MCU). Within the power-management hierarchy of embedded systems, the dsPIC33EV family sits above basic PIC16/PIC18 MCUs and targets real-time control loops where deterministic multiply-accumulate throughput, fast interrupt latency and robust on-chip peripherals such as high-resolution PWM are required. Key features include the 5V-tolerant dsPIC33E core running up to 70 MIPS, 64KB of ECC Flash that detects and corrects single-bit memory errors for safety-critical designs, 8KB of on-chip RAM, and four direct memory access (DMA) channels that offload data movement from the CPU. The device integrates seven timers and fixed-point DSP engine features including a barrel shifter, DSP multiply and dual-operand fetch for efficient control-law execution. The extended-temperature E-grade silicon is characterized across -40C to +125C, and the dsPIC33EV family datasheet (Microchip document DS70005144H, 506 pages) highlights on-chip peripherals tailored for safety motor control: advanced PWM modules, SENT peripheral support, and integrated operational amplifiers that reduce external component count in current-sense paths. The 5V I/O domain is a differentiator in harsh automotive and industrial environments, improving noise margin versus 3.3V-only competitors and allowing direct drive of many field-level signals without level shifting. Typical applications include sensorless BLDC and PMSM motor control, electric power steering and automotive sensor units, appliance motor drives, and industrial control nodes exposed to vibration, noise and wide temperature swings. A key design consideration is power supply decoupling: each VDD/VSS pin pair should have a low-ESR 0.1uF ceramic capacitor placed as close as possible to the pins, and the on-chip regulator capacitor pin must follow the datasheet connection guidelines for reliable core-power operation. This page synthesizes distributor availability data, family-level specifications, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $3.20 재고 있음

DSPIC33FJ128GP710-I/PF

dsPIC33FJ128GP710-I/PF - 16-bit 40 MIPS DSC 128KB Flash | Microchip

The Microchip Technology DSPIC33FJ128GP710-I/PF is a 16-bit digital signal controller (DSC) delivering up to 40 MIPS performance with 128 KB of flash program memory and 16 KB of SRAM, housed in a 100-pin TQFP (PF) surface-mount package rated for -40C to +85C operation. A digital signal controller combines the computational capability of a digital signal processor with the peripheral set and control-oriented architecture of a microcontroller. In the semiconductor hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: like an MCU it integrates timers, UARTs, ADCs, and general-purpose I/O; like a DSP it provides single-cycle MAC instructions and a barrel shifter. The dsPIC33F family belongs to the broader 16-bit PIC architecture lineage, with seamless migration options to and from PIC24 and dsPIC30F devices. Key features of the DSPIC33FJ128GP710 include a modified Harvard architecture with a 17-bit x 17-bit hardware multiplier and multiple internal bus capabilities, 51 I/O ports for extensive peripheral interfacing, and a supply voltage range of 3.0V to 3.6V (3.3V nominal). The device includes 2 KB of dual-ported DMA RAM, enabling efficient data movement between peripherals and memory without CPU intervention, which is essential for high-throughput signal processing pipelines. Technically, the core supports fixed-point DSP operations including single-cycle multiply-accumulate and hardware division assist, while the flash programming specification supports in-circuit serial programming (ICSP) through paired PGECx/PGEDx pin pairs. Clock speed reaches 60 MHz per reference data (40 MIPS instruction throughput at the 4x PLL configuration typical of this family). The General Purpose (GP) variant emphasizes advanced analog integration, communications, and general-purpose digital signal control. Typical applications include motor control and power conversion systems, digital audio and sensor signal processing, industrial automation controllers, and instrumentation where 16-bit control plus DSP math is required. The 100-pin TQFP provides abundant I/O for parallel interfacing, multiple communication buses, and external memory expansion. Design consideration: all VDD and VSS pins must be connected for reliable operation, and programming requires using a matched PGECx/PGEDx pair, as mixed pairs will cause ICSP failures. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, as of 2026-09-26.

USD $5.68 재고 있음

DSPIC33FJ256MC510T-I/PT

dsPIC33FJ256MC510T-I/PT - 16-bit 40 MIPS DSC 256KB Flash | Microchip

The Microchip Technology dsPIC33FJ256MC510T-I/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance with 256KB of FLASH program memory and 16KB of RAM, housed in a 100-pin TQFP (12x12 mm) surface-mount package. A digital signal controller combines the computational engine of a microcontroller (MCU) with the math acceleration of a digital signal processor (DSP) in a single chip. Within the power management hierarchy of embedded systems, a DSC sits above a general-purpose MCU for control-loop-intensive tasks: it executes fast multiply-accumulate operations for field-oriented motor control, digital power conversion (PI/PID loops), and sensor signal processing while retaining MCU-style peripherals, interrupts, and low-cost development tooling. The dsPIC33F family from Microchip occupies this MCU-to-DSP intersection, with seamless migration paths to PIC24 MCUs and dsPIC30F DSCs in similar packages. Key features of this part include the 16-bit dsPIC33F core clocked at up to 40 MIPS, 256KB (256K x 8) of on-chip FLASH for application and bootloader storage, and operation from a 3V to 3.6V single supply. The MC suffix denotes the motor-control peripheral set within the dsPIC33F family, which pairs DSP math capability with motor-control oriented peripherals for closed-loop drive applications. Architecturally, the dsPIC33F core uses a modified Harvard pipeline with DSP instruction support (MAC, DSP multiply, modulo addressing), enabling deterministic single-cycle DSP math at 40 MIPS. This makes the controller well matched to space-vector PWM generation and current-loop bandwidths of a few kilohertz and above. Typical applications include brushless DC (BLDC), permanent-magnet synchronous and AC induction motor drives, single- and three-phase power conversion, digital UPS and solar inverter control, and industrial automation nodes requiring sensor fusion with fast control loops. Design consideration: operate the device within the 3.0V to 3.6V supply window specified by the datasheet and decouple all VDD/VDDCORE pins per the Microchip layout guidelines; the 100-TQFP exposes numerous ground pins that must be tied to a solid ground plane for analog and DSP noise performance. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing verified as of 2026-09-27.

USD $5.55 재고 있음

DSPIC33FJ32GP204-I/PT

dsPIC33FJ32GP204-I/PT - 40 MIPS 16-bit DSC 32KB Flash | Microchip

The Microchip Technology DSPIC33FJ32GP204-I/PT is a high-performance 16-bit digital signal controller (DSC) delivering 40 MIPS from a 40 MHz core, with 32 KB Flash program memory, 2 KB SRAM, and a 44-pin TQFP (10 x 10 mm, 0.8 mm pitch) package. A digital signal controller combines the control peripherals and ease of use of a microcontroller with the computational throughput of a digital signal processor, placing it within the broader hierarchy of 16-bit microcontrollers and embedded processors. DSCs are optimized for executing digital filter algorithms and high-speed precision digital control loops, making them ideal for applications that must perform under pressure. Key features include up to four high-speed comparators with direct connection to the PWM module, a 10-bit high-speed ADC, high-speed PWM outputs, and Peripheral Pin Select (PPS), which allows many digital peripherals to be remapped to any of the 35 available I/O pins. The device executes DSP instructions such as single-cycle MAC with dual 40-bit accumulators, enabling efficient FIR/IIR filtering without an external DSP. Architecturally, the dsPIC33F uses a modified Harvard RISC pipeline with a 16-bit data path and C compiler-friendly instruction set, operating from a 3.0 V to 3.6 V single supply. In-Circuit Serial Programming (ICSP) and debugging via PGECx/PGEDx pins simplify production programming and field updates. Typical applications include digital power supplies, motor control (PMSM, BLDC, ACIM), sensor signal conditioning, digital filtering, and industrial control systems where precise analog integration and fast control loops are required. Design consideration: keep ICSP trace lengths short per the Microchip datasheet, and account for the 3.0-3.6 V supply window when interfacing with 5 V systems. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3.78 재고 있음

DSPIC33FJ32GS606-E/MR

dsPIC33FJ32GS606-E/MR - 16-bit DSC 40MIPS 32KB Flash | Microchip

The Microchip Technology dsPIC33FJ32GS606-E/MR is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance, 32KB of Flash program memory, and 4KB of RAM, housed in a 64-pin VQFN (9x9 mm) package with exposed pad and an extended industrial temperature rating of -40C to +125C. A digital signal controller combines the deterministic control of a microcontroller (MCU) with the mathematical throughput of a digital signal processor (DSP) in a single core. In the power-management hierarchy, the dsPIC33FJ GS series sits at the application level of switch-mode power supply (SMPS) control: it closes current- and voltage-control loops that would otherwise require multiple analog ICs, making it a programmable power-conversion controller rather than a fixed-function chip. Key features include a high-speed PWM module purpose-built for power conversion, high-speed ADC and analog comparators for cycle-by-cycle current limiting, four DMA channels, eight timers, boundary-scan (JTAG) capability, a barrel shifter for fast DSP math, and dual serial I/O ports on a multiple internal bus architecture. These peripherals directly support multi-loop digital power topologies. Technically, the dsPIC RISC core executes most instructions in a single cycle at up to 40 MIPS from a 3.0V to 3.6V (3.3V nominal) supply. The dedicated PWM hardware supports complementary outputs, dead-time insertion, and fault protection, while the fast ADC can synchronize sampling to the PWM period, which is essential for stable average-current-mode control. An internal regulator requires a low-ESR capacitor of at least 22 uF, 16V on the VCAP pin, which must not be tied to VDD. Typical applications are AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages including interleaved PFC reference designs up to 350W, uninterruptible power supplies (UPS), and solar inverters. For design, budget the VCAP capacitance and PCB copper area early: at 40 MIPS the core draws its full current continuously in power-conversion duty, and incorrect VCAP decoupling is a leading cause of brown-out resets in this family. This page adds value beyond the datasheet by consolidating distributor stock and pricing, same-package drop-in alternatives, and practical design notes for digital power designs in one place.

USD $4.42 재고 있음

DSPIC33FJ64MC710-I/PT

dsPIC33FJ64MC710-I/PT - 16-bit DSC 40MIPS 64KB Flash | Microchip

The Microchip Technology dsPIC33FJ64MC710-I/PT is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS from its dsPIC33F core, with 64KB of Flash program memory, industrial -40C to +85C temperature rating, and a 100-pin TQFP (PT) surface-mount package operating from a 3V to 3.6V supply. A Digital Signal Controller combines the computational throughput of a digital signal processor with the deterministic peripherals and simplicity of a microcontroller, sitting in the hierarchy between a general-purpose MCU and a dedicated DSP. DSCs execute DSP-class instructions such as multiply-accumulate and modulo addressing while retaining MCU-class interrupt latency, making them the preferred device class for closed-loop digital control systems. Key features of the dsPIC33FJ64MC710 include high-performance motor-control peripherals such as motor control PWM outputs, 12-bit high-speed ADCs suited to current-loop sampling, and ECAN modules for automotive and industrial networking. According to the Microchip datasheet, the dsPIC33F Motor Control family offers seamless migration options to PIC24F, PIC24H MCUs and dsPIC30F DSCs in similar packages, protecting software investment across product generations. Architecturally, the dsPIC33F uses a modified Harvard 16-bit RISC core with DSP engine instructions, and supports multiple PGECx/PGEDx In-Circuit Serial Programming (ICSP) pin pairs for debugging and programming via standard Microchip tools. Typical applications include brushless DC motor control, single- and three-phase induction motor drives, switched reluctance motors, uninterruptible power supplies, digital power conversion, and industrial automation nodes requiring CAN connectivity. When designing, ensure the 3V-3.6V supply rail is well decoupled and that all PGEC/PGED pairs are routed as pairs for debug access. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet alone.

USD $6.80 재고 있음

eZ80F91AZ050SG

eZ80F91AZ050SG - 50MHz 8-bit 256KB Flash MCU | Zilog

The Zilog eZ80F91AZ050SG is an 8-bit microcontroller in the eZ80 Acclaim! family, delivering 50 MHz CPU performance with 256 KB of on-chip Flash and 16 KB SRAM in a 144-pin LQFP (20x20 mm) package. According to DigiKey listing 928880, the part integrates an EMAC (Ethernet Media Access Controller) for embedded networking and supports both Z80-compatible (64 KB) and full 24-bit (16 MB) addressing modes. An 8-bit microcontroller (MCU) is a single-chip processor whose internal data path is 8 bits wide, optimized for control-oriented tasks that demand deterministic behaviour, low cost, and minimal power. The eZ80 architecture extends the classic Z80 instruction set with a 24-bit linear address space, making it a bridge between legacy 8-bit code and 32-bit addressing. Within the IC taxonomy it sits at: microcontroller -> embedded processor -> integrated circuit. It belongs to the broader class of flash microcontrollers and is commonly deployed in industrial control and embedded communication designs. Key features include 32 general-purpose I/O pins, four 16-bit timers, a 10/100 Ethernet MAC with MII interface, two UARTs, I2C, SPI, IrDA encoder/decoder, and a JTAG debug port. The on-chip peripherals are designed for embedded internet connectivity, while the SRAM-backed Flash supports in-application programming for field upgrades. The eZ80F91AZ050SG uses a single-cycle pipelined core running at 50 MHz, providing sustained throughput equivalent to 80 MIPS peak (Z80 instructions). The integrated EMAC implements full IEEE 802.3 MAC and PHY interfacing, eliminating the need for an external Ethernet controller in point-of-sale and embedded gateway designs. Typical applications include industrial control, point-of-sale (POS) terminals, embedded communication gateways, security systems, and building automation. The wide address space makes the device attractive for legacy Z80 software migration and new 24-bit flat-memory designs. Design considerations include ensuring proper decoupling on the analog supply pins, following the recommended 50 MHz crystal layout, and reviewing Zilog application note PS0192 for EMAC magnetics and PHY interface. The device operates from a 3.3 V supply. This page consolidates verified distributor pricing, drop-in Zilog alternatives, and application guidance not collated in the standalone datasheet, providing an integrated reference for embedded engineers.

USD $10.85 재고 있음

i7-1370PRE

i7-1370PRE - 14C/20T Embedded Raptor Lake, 24MB Cache | Intel

The Intel Core i7-1370PRE is a 13th Generation Raptor Lake mobile/embedded processor featuring 14 cores (6 Performance + 8 Efficient), 20 threads, 24 MB Intel Smart Cache, and a maximum turbo frequency of 4.80 GHz, designed in the FC-BGA16F package. Built on Intel 7 process technology, it supports up to 96 GB DDR5/DDR4 memory and integrates Intel Iris Xe graphics (96 EU). The processor operates with a 28 W processor base power and targets embedded and industrial applications requiring long-life availability. An embedded processor is a CPU designed for use in industrial, in-vehicle, or IoT systems where long-term availability (typically 10+ years), extended temperature tolerance, and platform stability are critical. Embedded CPUs sit within the broader taxonomy: processor -> central processing unit (CPU) -> mobile/embedded CPU -> Raptor Lake family -> Intel Core i-series. The 'PRE' suffix in Intel's mobile roadmap specifically denotes an embedded SKU qualified for long-life cycles, distinct from mainstream consumer 'P' parts. Key specifications include 6 P-cores with hyper-threading up to 5.0 GHz peak and 8 E-cores up to 3.7 GHz, 24 MB L3 cache, 96 EU Iris Xe graphics at 1.50 GHz, and 28 W processor base power configurable down to 20 W. The FC-BGA16F socket (1744-ball FCBGA) provides platform integration. Memory support includes DDR5-5200, DDR4-3200, LPDDR5-6400, and LPDDR4x-4267 with ECC capability. Architecturally, the i7-1370PRE uses Intel's hybrid P-core/E-core design, where Performance cores handle single-threaded latency-critical work and Efficient cores process throughput-oriented background tasks via Intel Thread Director scheduling. The 10 nm Intel 7 process allows higher core counts within embedded thermal envelopes, and the integrated Iris Xe GPU enables display and light GPGPU workloads without a discrete GPU. Typical applications include industrial edge computing, in-vehicle infotainment, factory automation HMIs, medical imaging systems, and digital signage. The 'E' (embedded) qualification extends operating temperature support and supply longevity compared to standard 'P' siblings. When designing with this CPU, select motherboards and chipsets engineered for the FC-BGA16F socket rather than consumer LGA sockets, validate thermal design at the configured cTDP, and confirm chipset firmware supports the specific embedded SKU. ECC memory and Intel vPro features require compatible PCH selection. This page synthesizes distributor pricing, Intel ARK specifications, cross-reference alternatives, and PCB/socket design notes to support embedded system engineers selecting between long-life Intel SKUs and cross-generational replacements.

USD $365.00 재고 있음

i7-5700HQ

i7-5700HQ - 4C/8T Broadwell-H Mobile CPU up to 3.5GHz | Intel

The Intel Core i7-5700HQ is a 4-core, 8-thread mobile processor built on Intel's 14nm Broadwell-H architecture, launched in June 2015 at a $378 MSRP. It operates at a 2.70 GHz base clock with Intel Turbo Boost up to 3.50 GHz, integrates 6 MB of L3 cache, and is soldered onto the motherboard in a BGA-1364 package (also referenced as FCBGA-1364). The i7-5700HQ supports dual-channel DDR3L-1600 memory and is rated at a 47 W TDP, making it a mainstream performance CPU for 2015-era gaming and workstation notebooks. A mobile quad-core processor (HQ-class) is Intel's high-performance tier for laptops, sitting above U-series (ultrabook) and H-series dual-core parts. The Core i7 brand indicates Hyper-Threading, larger cache, and higher Turbo ceilings than Core i5/i3 siblings. Broadwell-H represents the 5th-generation Core microarchitecture, succeeding Haswell with a 14nm tri-gate process, an updated integrated Iris Pro 6200 GPU, and improved instruction-per-clock efficiency. These processors are soldered (BGA) and not user-upgradeable. Key features include 4 physical cores with Hyper-Threading for 8 logical threads, a 6 MB shared L3 cache, and a configurable TDP-down mode of 35 W for thermal-constrained chassis. The integrated Iris Pro 6200 graphics with 48 execution units and 128 MB of eDRAM (L4 cache) provides modest gaming capability and Quick Sync video acceleration. AVX2 and AES-NI instructions accelerate compute and cryptographic workloads. Architecturally, Broadwell-H pairs an updated out-of-order core with a ring interconnect to the System Agent, integrated memory controller, and GT3e-class graphics. The 14nm process allowed higher frequencies at the same 47 W envelope versus the 22nm Haswell predecessor, while the 128 MB eDRAM side-cache boosts both CPU and GPU bandwidth when working on data sets that fit inside it. Typical applications include 2015-2016 era gaming laptops, mobile workstations running CAD or video editing software, and high-performance ultrabooks where the 47 W TDP can be cooled. The quad-core/8-thread configuration suits multi-tasking, video encoding, and lightly threaded productivity. The integrated GPU also enables headless media transcode via Quick Sync. Design consideration: because this is a BGA-1364 soldered part, replacement requires motherboard-level rework. When sourcing refurbished laptops, verify the BIOS supports the i7-5700HQ stepping and pair with dual-channel DDR3L-1600 SODIMMs to avoid memory bandwidth bottlenecks to the integrated GPU. This page synthesizes distributor listings, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $62.00 재고 있음

하위 카테고리

제품 (29810)