집적 회로

Si5341B-B04862-GM

Si5341B-B04862-GM - 10-Output Ultra-Low Jitter Clock Generator | Skyworks

The Skyworks Solutions Si5341B-B04862-GM is a pre-programmed, custom-configured variant of the Si5341B ultra-low jitter any-frequency clock generator family. The device delivers up to 10 differential or single-ended clock outputs at any frequency up to 750 MHz (with <350 MHz jitter-optimized outputs available), in a 64-pin QFN (9x9 mm) package with exposed pad for thermal dissipation. The on-board MultiSynth technology generates independent fractional-N synthesizers per output, allowing non-integer frequency relationships that cannot be realized by integer-N PLLs. A clock generator (also called a frequency synthesizer or PLL-based timing IC) is a mixed-signal integrated circuit that takes one or more low-jitter reference inputs (typically a crystal or LVDS/CMOS reference) and produces one or more precise output frequencies locked to that reference. Within the broader hierarchy it sits as: clock generator -> PLL/VCXO -> timing IC -> power management & signal chain. Unlike a simple clock buffer, a clock generator can translate frequency (e.g., 25 MHz in to 156.25 MHz out), translate format (LVCMOS to LVDS/LVPECL/HCSL/CML), and re-multiply reference, all while adding typically <100 fs RMS phase jitter to the signal. Key features of this Si5341B configuration include typical RMS phase jitter of 50 fs (12 kHz-20 MHz, per the Si5341/40 family datasheet), integrated LDOs that accept a single 1.8V/2.5V/3.3V supply, two differential reference inputs with automatic or manual switching, programmable output slew rate and amplitude, and per-output enable / glitchless start/stop. The device is configured via I2C/SPI and the Skyworks ClockBuilder Pro software. Architecturally the Si5341B combines a low-noise integer-N PLL locking to the reference, a MultiSynth fractional-N divider tree per output, and an output-driver block supporting LVCMOS, LVDS, LVPECL, HCSL, and CML. The MultiSynth architecture eliminates the need for bulky external VCXOs in most applications because any fractional multiplication ratio is supported without integer-boundary spurs. Typical applications include 10G/25G/100G Ethernet PHY clocking, OTN/WDM optical transport line cards, FPGA reference clock trees, broadcast video reference generation, JESD204B/C ADC and DAC sampling clocks, and PCIe Gen3/4/5 clock fan-out. Each output can be set independently so a single Si5341B-B04862-GM can replace multiple crystal oscillators on a high-density PCB. When designing with this part, follow the reference schematic in the Si5341/40 Family Reference Manual exactly. Place the 0.1 µF + 1 µF supply decoupling pair directly at the AVDD/VDD pins, route the reference input traces as 50 Ω controlled-impedance differential pairs, and provide a continuous ground plane beneath the exposed pad with at least 12 thermal vias to the internal layer. This page synthesizes Skyworks datasheet specifications, current distributor pricing as of 2026-10-10, drop-in replacement options within the Si5341/Si5340 family, and practical design notes that complement (but do not replace) the manufacturer documentation.

USD $21.10 재고 있음

T1014NSN7MQPA

T1014NSN7MQPA - QorIQ 1.2GHz 64-bit Power Arch MPU | NXP

The NXP T1014NSN7MQPA is a single-core 64-bit Power Architecture communications processor from the QorIQ T1 family, running at 1.2 GHz and housed in a 780-pin FBG BGA (23x23 mm) package. It integrates a single e5500 core with Data Path Acceleration Architecture (DPAA) hardware acceleration, DDR3L/DDR4 memory controllers, PCIe, and 1G/10G Ethernet interfaces for high-performance networking and industrial applications. The 0 °C to 105 °C industrial temperature grade and deep-sleep power mode make it suitable for thermally constrained, always-on networking equipment. A microprocessor (MPU) is a single-chip CPU containing the arithmetic logic unit, control unit, registers, cache, and memory management logic needed to execute operating systems and application workloads. Within the SoC hierarchy, an MPU integrates processor cores with on-chip peripherals (memory controllers, bus fabrics, accelerators, networking MACs), distinguishing it from a microcontroller (MCU) which typically targets control loops with on-chip flash. The T1 series occupies the networking/communications tier of NXP's QorIQ lineup, sitting below the multi-core T2/T4 layerscale parts and above the entry P-series. Key features of the T1014NSN7MQPA include a single 64-bit Power Architecture e5500 core at 1.2 GHz, DPAA for packet parsing, classification, and crypto offload, integrated DDR3L/DDR4 controller with ECC, multiple PCIe Gen2 controllers, 1 Gbit Ethernet and 10 Gbit Ethernet MACs, and a deep-sleep low-power mode. Security is handled by the on-chip SEC engine, and the 780-FBGA package exposes the full T1 serial bus, including SerDes lanes for high-speed networking. The DPAA architecture offloads buffer management, queueing, and cryptographic operations from the e5500 core, allowing line-rate packet processing at lower clock frequencies than software-only designs. Compared with general-purpose SoCs, the T1014NSN7MQPA offers deterministic I/O latency and hardware-accelerated networking, which is essential for router, switch, and security appliance workloads. Typical applications include industrial routers, network switches, security gateways, factory automation controllers, and edge networking appliances. The 23x23 mm package footprint is shared across the T1 series, simplifying PCB layout reuse among T1013, T1014, T1023, and T1024 variants. When designing with the T1014NSN7MQPA, allocate adequate PCB area for the 780-ball FBG BGA, plan thermal management for full-power operation, and verify DDR3L/DDR4 routing and impedance per the NXP hardware design guide. For higher core count or throughput, step up to the dual-core T1024 in the same package.

USD $88.90 재고 있음

T1020NSE7MQB

T1020NSE7MQB - QorIQ T1 2-Core 1.4GHz e5500 SoC | NXP

The NXP T1020NSE7MQB is a dual-core QorIQ T1 communications processor featuring two integrated 64-bit e5500 Power Architecture cores running up to 1.4 GHz, packaged in a 780-pin FCBGA (23x23 mm). The part integrates hardware-accelerated cryptography, an integrated Ethernet switch, DDR3L/DDR4 memory controllers, and the Data Path Acceleration Architecture (DPAA) for high-performance packet processing. What is a QorIQ communications processor? QorIQ is a NXP processor family targeting networking, telecom, and industrial infrastructure. The T1 series sits at the lower-power dual-core end of the QorIQ T lineup, positioned between the single-core T1014 and the quad-core T1040/T2080 tier. These SoCs combine general-purpose Power Architecture cores with hardware assist engines (SEC for crypto, DPAA for packet parsing/queueing, and integrated Ethernet MACs/switch), enabling line-rate L2-L4 processing without external lookup engines. They belong to the broader communications processor hierarchy: SoC -> microprocessor -> communications processor -> embedded processor. Key features of the T1020NSE7MQB include dual 64-bit e5500 cores with hardware hypervisor support, integrated 32-bit DDR3L/DDR4 memory controller with ECC, integrated 1G/2.5G Ethernet switch fabric, SEC 4.0 crypto accelerator, DPAA for parsing/classification/queueing, two PCIe Gen2 controllers, and four SerDes lanes for SGMII/XAUI. Operating temperature range is 0C to 105C, targeting industrial and extended-temperature networking equipment. The 780-FCBGA package supports the high-speed SerDes and memory interfaces required for multi-gigabit switching. Architecturally, the T1020 uses the e5500 core, a 64-bit superscalar Power Architecture implementation with out-of-order execution, integrated MMU, and hardware virtualization (hypervisor) extensions. The DPAA subsystem offloads frame parsing, classification, and queue management to dedicated engines, freeing the e5500 cores for control-plane and application-layer processing. SEC 4.0 accelerates AES, 3DES, SHA, RSA, and ECC, supporting IPSec, TLS/DTLS, and MACsec at line rate. The integrated Ethernet switch eliminates an external PHY/bridging device in small-port-count designs. Typical applications include industrial Ethernet switches (managed 8-24 port switches), factory automation gateways, IEC 61850-3 substation controllers, edge routers, and ruggedized industrial control platforms where 1-2 cores are sufficient for control-plane and protocol conversion but packet-plane needs hardware assist. The 0-105C temperature range allows deployment in outdoor enclosures and industrial cabinets. For design planning: plan the PCB for 23x23 mm FCBGA with microvia stack-up; provide at least 4 PCB layers with dedicated ground references for SerDes lanes; allocate thermal copper under the package to dissipate the typical 8-12W TDP at 1.4 GHz; and validate DDR3L/DDR4 topology against the NXP reference design guidelines for signal-integrity. This page synthesizes distributor pricing, drop-in QorIQ alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $88.75 재고 있음

T1023NSE7MQA

T1023NSE7MQA - QorIQ 2xCPU 64-Bit 1.2GHz MPU | NXP | FCBGA-525

The NXP T1023NSE7MQA is a QorIQ communications microprocessor that integrates two 64-bit Power Architecture e5500 cores running at 1.2 GHz, packaged in a 525-ball FCBGA at a 19x19 mm body size. It is engineered for networking, telecommunications, and industrial networked applications that require hardware-accelerated packet processing with strong crypto throughput. A microprocessor (MPU) is a single-chip CPU with integrated peripherals and memory interfaces that executes an operating system and application workloads. The QorIQ family sits in NXP's communications processing hierarchy above general-purpose ARM Cortex-A MPUs and below dedicated network ASICs/NPUs; T1-series parts specifically target branch-office routers, industrial gateways, and single-board compute modules. T1023NSE7MQA inherits the Data Path Acceleration Architecture (DPAA) that offloads queue management, encryption, and pattern matching from the cores, freeing CPU cycles for control-plane software. Key features include dual e5500 cores at 1.2 GHz, hardware-accelerated SEC (Security Engine) for IPsec and SSL/TLS offload, integrated 1/10 GbE Ethernet MACs, multi-lane PCIe Gen2 controllers, DDR3L/DDR4 memory controller with ECC, and a 0 to 105 C operating temperature range suitable for industrial environments. The 525-FCBGA package uses a 0.8 mm ball pitch and provides the signal integrity required for 1.2 GHz core clocks and high-speed SerDes lanes. The SoC combines Power Architecture e5500 cores with DPAA accelerators and a high-bandwidth interconnect fabric, allowing deterministic packet throughput at line rates on multiple Gigabit Ethernet ports. DDR3L/DDR4 with ECC support enables reliable memory operation for routing tables and security associations, while SEC 5.x acceleration handles bulk cryptographic workloads. Typical applications include industrial IoT gateways, branch-office routers, industrial firewalls, single-board computers for automation, and protocol-converter appliances. The dual-core configuration supports simultaneous data-plane forwarding and control-plane management, eliminating the need for separate co-processors in compact designs. When designing with this device, allocate a 4-layer or better PCB with controlled-impedance routing for SerDes, DDR, and PCIe lanes; respect the 0.8 mm BGA pitch with microvia stackups. Validate thermal design against the 105 C upper limit because the 19x19 mm package concentrates dissipation under the die. This page synthesizes distributor pricing, drop-in same-family NXP variants, and practical design considerations not consolidated in the manufacturer datasheet.

USD $205.00 재고 있음

T1024NSE7MQA

T1024NSE7MQA - QorIQ Dual-Core 1.2GHz Power Arch SoC | NXP

The NXP T1024NSE7MQA is a QorIQ T1 series dual-core communications processor that integrates two 64-bit Power Architecture e5500 cores running at 1.2 GHz, combined with hardware Data Path Acceleration Architecture (DPAA), a SEC crypto engine, DDR3L/DDR4 memory controller, PCIe, and 1/10 GbE networking interfaces, in a 780-pin HFBGA package on a 23x23 mm body with 0 to 105C industrial temperature grade. A communications SoC (System-on-Chip) is an integrated processor that combines CPU cores, memory controllers, hardware accelerators and peripheral interfaces on a single die. QorIQ T1 series SoCs sit within NXP's networking processor hierarchy: application-specific CPU -> embedded communications processor -> SoC -> power-managed networking platform. By integrating DPAA frame queues, SEC encryption, and SerDes for Ethernet and PCIe, the platform eliminates the discrete-asset controller ICs required in legacy designs. Key features include dual e5500 cores up to 1.2 GHz, 64-bit ISA with hypervisor support, an integrated SEC security engine accelerating AES, 3DES, Kasumi, SNOW and public-key algorithms, and built-in DDR3L/DDR4 SDRAM controller with ECC. The HFBGA-780 package exposes 4 SerDes lanes configurable for Aurora, XAUI, PCIe Gen2 and 10 Gigabit Ethernet. Hardware support for IEEE 1588 timestamps, packet parsing and queuing offloads CPU load at line rate. Architecturally the part relies on the Power Architecture e5500 dual-issue superscalar core with symmetric multiprocessing and hardware virtualization hooks. The DPAA engine uses a 16-work-element command queue per BMan/QMan complex for parallel packet dispatch. The integrated SEC block supports both Kasumi and SNOW 3G, suiting the part to LTE control-plane cryptography in addition to wireline IPSec tunnels. Typical applications include industrial control routers, LTE small-cell baseband, fan-less network-attached storage controllers, secure VPN gateways and intelligent IoT gateways. Routing platforms typically pair the T1024NSE7MQA with NXP SGMII PHYs, while control-plane applications use only the SEC block and a small NOR flash footprint. Designers should size decoupling for the HFBGA-780 substrate to keep the 1.2 GHz core within the 0 to 105C thermal envelope, and verify SerDes lane allocation when mapping XFI, PCIe and Aurora on the same SoC. PCB layout must strictly follow the NXP 23x23 mm escape rules for the BGA. This page synthesizes distributor pricing, drop-in alternatives drawn from the QorIQ T1 family, and practical design notes not aggregated on any single manufacturer page.

USD $74.10 재고 있음

T1024NSN7PQA

T1024NSN7PQA - QorIQ Dual-Core 1.4GHz PowerPC MPU | NXP

The NXP T1024NSN7PQA is a QorIQ communications processor integrating dual 64-bit Power Architecture e5500 CPU cores running at up to 1.4 GHz, paired with a high-performance data path acceleration architecture (DPAA), in a 780-pin HFBGA 23x23 mm package. According to the verified manufacturer description, it supports DDR3L/DDR4 memory, PCI Express Gen2/Gen3 controllers, 1 GbE and 10 GbE interfaces, and targets commercial/industrial thermal grades (0C to 105C). A QorIQ communications processor is a system-on-chip (SoC) microprocessor built on the Power Architecture instruction set, designed for wired and wireless networking equipment. The T1024 belongs to the QorIQ T1 family, which sits in the broader NXP processor taxonomy as: PowerPC e5500 core -> QorIQ T1 communications SoC -> embedded networking MPU -> Power Architecture processor family. This hierarchy positions it between general-purpose microcontrollers (no integrated networking) and high-end multicore QorIQ T2/T4 processors. Key differentiating specifications include the dual e5500 cores (vs. single-core T1014/T1013), 1.4 GHz frequency, hardware-accelerated packet processing via DPAA, integrated SerDes lanes supporting multiple 1 GbE and 10 GbE ports, and a compact 23x23 mm package that maintains pin compatibility with the quad-core T1042 and even the eight-core T2081 for single-PCB scalability. The 780-ball HFBGA package supports the high I/O count needed for multiple Ethernet, PCIe, and DDR interfaces. Architecturally, the T1024NSN7PQA combines Power Architecture e5500 superscalar cores with NXP's Data Path Acceleration Architecture (DPAA), which offloads packet parsing, queue management, and buffer allocation from the cores. This hardware acceleration is critical for line-rate throughput in routers, switches, and network appliances where software-only packet processing cannot scale. Typical applications include industrial routers and switches, network interface cards (NICs), LTE/5G small cell base stations, industrial IoT gateways, and secure networked embedded appliances requiring deterministic packet throughput. The DDR3L/DDR4 controller supports low-power memory operation for thermally constrained designs. When designing with this processor, careful PCB layout is essential - the 780-ball BGA requires microvia or via-in-pad technology, length-matched DDR traces, and a solid ground/power plane stackup. The commercial/industrial temperature grade (0 to 105C) makes it suitable for indoor and outdoor sealed enclosures but not extended-temperature automotive deployments.

USD $73.15 재고 있음

T1042NSE7MQPB

T1042NSE7MQPB - QorIQ 4x e5500 1.2GHz MPU w/ Crypto | NXP

The NXP T1042NSE7MQPB is a QorIQ communications processor featuring four 64-bit e5500 Power Architecture cores running at up to 1200 MHz, integrated with the Data Path Acceleration Architecture (DPAA) and hardware cryptography acceleration, housed in a 780-pin FCBGA package. It supports DDR3L/DDR4 memory with a high-performance interconnect and a rich set of networking peripheral interfaces required for embedded networking and telecommunications systems. A microprocessor (MPU) is a single-chip processing unit that integrates one or more CPU cores, caches, memory controllers, and I/O peripherals onto one die, forming the central compute engine of an embedded system. The QorIQ T1 family sits within NXP's communications processor portfolio above simple microcontrollers and below high-end Layerscape SoCs, serving as a scalable platform for industrial control, printer/market controllers, and entry-level networking equipment where deterministic performance, hardware offload, and industrial temperature grades are required. Key features include four e5500 cores with double-precision floating point, DPAA for packet parsing, queueing, and crypto acceleration, hardware security engines supporting AES, DES, SHA, RSA, and Kasumi, integrated DDR3L/DDR4 controller, multiple Gigabit Ethernet MACs (SGMII/RGMII), PCIe Gen 2 controllers, SATA, USB, and SerDes interfaces, and an extended industrial operating temperature range of 0 to 105 degrees C with the 'PB' speed/grade suffix and the 'MQ' marking denoting 'No Switch' silicon revision. The architecture pairs high-frequency out-of-order execution cores with tightly-coupled DPAA engines, offloading packet classification, encryption, and queue management from the cores. The result is deterministic throughput on routing, IPSec, and deep packet inspection workloads while keeping the application cores free for control-plane tasks. The 780-pin FCBGA package exposes all DPAA ports and SerDes lanes, enabling single-chip designs for managed switches, routers, and industrial gateways without companion communication ASICs. Typical applications include industrial Ethernet switches, routers and gateways, secure network appliances, multi-function printers and imaging systems, factory automation controllers, and smart-grid / IEC 61850 substation equipment. The 0 to 105C operating range and long-life industrial grade make this part a fit for harsh-environment embedded systems requiring 10+ year product lifecycles. When designing with this device, allocate sufficient PCB real-estate for the 780-pin FCBGA and its associated DDR routing, provide adequate thermal relief for sustained 1.2 GHz operation, and follow NXP's reference design guidelines for power sequencing. The 'No Switch' ('N') suffix indicates the device ships without integrated Ethernet switch fabric, so multi-port designs require external PHY or switch companions. This page synthesizes authorized distributor stock, drop-in T1 family alternatives, and practical layout guidance not always visible in the manufacturer datasheet.

USD $132.00 재고 있음

T1042NSE7PQPB

T1042NSE7PQPB - QorIQ 4x e5500 1.4GHz MPU | NXP

The NXP Semiconductors T1042NSE7PQPB is a QorIQ T1 family communications processor that integrates four 64-bit e5500 Power Architecture cores running at 1400 MHz, with hardware cryptography, DDR3L/DDR4 memory controller, and Data Path Acceleration Architecture (DPAA). It is housed in a 780-ball FC-PBGA (23x23) package and targets industrial temperature ranges (0C to 105C). The device is designed for networked printers and embedded communications applications. A communications processor is a specialized system-on-chip that combines general-purpose CPU cores with hardware offload engines for packet processing, security, and high-speed I/O. Within the broader taxonomy, the T1042 sits at the top of the tree: communications processor -> microprocessor (MPU) -> integrated circuit -> semiconductor. The QorIQ T1 family is a scalable, pin-compatible platform that allows migration down to the dual-core T1022 and up to higher-performance devices such as the T2081, simplifying platform design across product tiers. Key specifications of the T1042NSE7PQPB include four e5500 cores at 1.4 GHz, 32 KB I-cache and 32 KB D-cache per core with 256 KB shared L2 per cluster, integrated SEC cryptography engine, DDR3L/DDR4 memory controller with ECC support, three PCI Express Gen 2 controllers, two SATA 2.0 ports, two USB 2.0 controllers with PHY, two Gigabit Ethernet controllers, and an integrated security engine for IPsec, SSL/TLS, and bulk encryption. The device supports hardware virtualization and implements the DPAA for hardware-assisted queue and buffer management. The architecture combines out-of-order Power Architecture execution with hardware-accelerated data path processing. The e5500 cores implement hardware virtualization through logical partition support and extended interrupt prioritization. The DPAA provides a standardized infrastructure for parallel packet processing, including frame managers, queue managers, and buffer managers that offload packet handling from the cores. Hardware security acceleration includes AES, 3DES, Kasumi, SHA-1/SHA-256, public-key accelerator, and a true random number generator. Typical applications include industrial and networked printers, multi-function peripherals, industrial control and factory automation gateways, ruggedized networking equipment, secure routers and VPN concentrators, and small-form-factor industrial servers. The absence of an integrated Ethernet switch reduces BOM cost for applications that already provide external switching, while the integrated PHYs and SEC engine minimize external component count. When designing with this device, ensure the FC-PBGA-780 substrate has adequate microvia stack-up to route the DDR3L/DR4 byte lanes with matched impedance. The thermal design must account for the 1.4 GHz quad-core power envelope; a heatsink or thermal interface material is recommended at sustained workloads above 70 percent utilization across all four cores. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $210.00 재고 있음

T2080NSE8MQB

T2080NSE8MQB - QorIQ T2 4-Core 1.2GHz e6500 MPU | NXP

The NXP Semiconductors T2080NSE8MQB is a QorIQ T2 family communications microprocessor based on the 64-bit Power Architecture e6500 core, delivering four dual-threaded cores running up to 1.2 GHz (eight virtual threads) on a 28 nm process. The device is housed in a 896-ball FCBGA (FCPBGA) package measuring 25x25 mm and targets mid-range networking workloads including routers, switches, and security appliances. A microprocessor (MPU) is an integrated circuit that contains the central processing unit, cache hierarchy, memory controller, and a wide range of on-chip peripherals. Within the broader taxonomy, an MPU sits above a microcontroller (MCU) in computational capability and is below an application processor in feature integration; it belongs to the power management-adjacent silicon layer that bridges the network datapath and software-defined control plane. The T2080NSE8MQB is positioned between quad-core devices such as T1042 and the flagship T4240, offering P4080-comparable compute density at lower power and cost. Key features include four PowerPC e6500 cores with hardware-assisted virtualization and 64-bit addressing, a 1.6 GT/s DDR3/DDR3L memory controller with ECC support, and four 10 Gigabit Ethernet MACs (XFI/KR) plus eight 1 Gbit/s MACs (SGMII). Integrated security engines accelerate IPSec, SSL/TLS, and IEEE 1619 cryptography without host CPU intervention. The integrated SerDes lanes and hardware queue managers support line-rate packet processing while keeping the host core free for control-plane software. Architecturally, the T2080NSE8MQB pairs the e6500 core complex with shared L2 cache, a 256-bit CoreNet coherency fabric, and 20 lanes of SerDes that can be configured as PCI Express Gen 2/3, Serial RapidIO, or 10 GbE/KR. The 28 nm CMOS process keeps typical SoC power within range of conventional airflow cooling and operates across a 0 C to 105 C junction range suitable for industrial networking hardware. Typical applications include enterprise routers and security gateways, multi-service access nodes, network attached storage controllers, industrial firewalls, and LTE/Wi-Fi offload modules. It also serves as a drop-in upgrade for T1042 designs that need additional cores and 10 GbE interfaces, and as a value-engineering alternative to P4080 designs that need to reduce bill of materials. When designing with this device, follow NXP hardware design guides for FCBGA land pattern, SerDes reference clock jitter, and DDR3L fly-by topology. Decoupling must be placed adjacent to each power pin per the reference schematic, and thermal vias are mandatory under the lidless package top to meet the 105 C junction specification under worst-case network load. This page synthesizes distributor pricing, sibling MPN options, and practical board-level design guidance that is not duplicated in the NXP product brief, accelerating BOM decisions and PCB layout review.

USD $199.50 재고 있음

T2080NXE8PTB

T2080NXE8PTB - QorIQ 8x 1.5GHz 64-bit MPU, 4x10GE | NXP

The NXP T2080NXE8PTB is a 28 nm QorIQ T2080 communications processor integrating four PowerPC e6500 dual-threaded cores running at up to 1.533 GHz with eight virtual threads, delivering 8x 1.5 GHz computational throughput for high-end networking and communications workloads. The device integrates four 10 Gigabit Ethernet controllers, an 1.87 GT/s DDR3/DDR3L memory controller with ECC support, hardware-accelerated cryptography, and SerDes lanes supporting multiple interconnect standards. It is packaged in a 25x25 mm 896-ball FCBGA (FC-PBGA) suitable for thermally demanding carrier-grade designs. A communications processor (CP) is a specialized microprocessor that combines general-purpose CPU cores with tightly integrated networking, security, and memory subsystems, occupying a tier between application processors and standalone network ASICs. Within the embedded taxonomy, the T2080 belongs to the QorIQ T2 series, which itself descends from Power Architecture-based communications platforms spanning L2/L3 switches, base stations, and edge routers. The e6500 core brings the architectural lineage of the T4240 flagship into a more power- and pin-efficient package. Key differentiating specifications include the e6500 dual-threaded core (eight hardware threads across four physical cores), 1.87 GT/s DDR3/DDR3L with ECC, four integrated 10 GbE MACs plus additional lower-speed Ethernet, hardware crypto acceleration, and -40C to +105C industrial temperature range support. The combination of 10 GbE MACs with hardware crypto acceleration in a single 28 nm die enables line-rate secure processing without off-chip coprocessors. The T2080 architecture implements the Book-E enhanced Power ISA with hypervisor-aware virtualization, a coherent fabric interconnecting cores and I/O, and queue manager acceleration for buffer descriptors. The integrated security engine supports symmetric ciphers, public-key algorithms, and true random number generation, offloading what would otherwise consume CPU cycles. Dynamic power management scales per-core frequency and voltage independently, allowing designers to trade throughput against thermals in thermally constrained SFP-router and MEC platforms. Typical applications for the T2080NXE8PTB include enterprise routers, multi-service switches, network-attached storage controllers, industrial gateways, LTE/5G small-cell base stations, and network security appliances. The integrated 4x10G plus multi-port 1G/2.5G Ethernet and hardware crypto make it especially suited for IPsec/SSL VPN gateways and line-rate deep-packet inspection systems. A key design consideration is PCB layout for the 896-ball FCBGA - a multilayer PCB with a continuous ground plane beneath the package is required for signal integrity of the multi-GHz SerDes lanes. Designers must also provide robust heatsinking because at 1.533 GHz the T2080 dissipates substantial power; airflow of at least 200 LFM is typically required for full-speed industrial operation. This page synthesizes distributor pricing, drop-in alternatives, design notes, and comparison tables that go beyond the manufacturer datasheet, helping procurement and design teams make informed decisions for next-generation networking platforms.

USD $305.00 재고 있음

T2081NSE8PTB

T2081NSE8PTB - QorIQ T2 4C 1.5GHz 896-FCPBGA | NXP Semiconductors

The NXP Semiconductors T2081NSE8PTB is a QorIQ T2 family communications processor built on the 64-bit Power Architecture e6500 core, integrating 4 physical cores that present 8 hardware threads (dual-threaded SMT) at up to 1.533 GHz core frequency. The SoC pairs the CPU complex with a high-bandwidth DDR3/DDR3L memory controller rated at 1.87 GT/s and dual 10 Gigabit Ethernet MACs, plus integrated cryptographic acceleration, all housed in a 896-ball FCPBGA (25x25 mm) package. Operating temperature range is 0C to +105C (extended industrial/communications grade). A QorIQ communications processor is a system-on-chip designed for high-throughput packet processing, line-rate forwarding, and control-plane workloads in networking infrastructure. Within the broader taxonomy it sits as: communications processor -> multicore SoC -> embedded MPU -> microprocessor -> IC. The T series spans the T1 (T1040/T1042, quad-core entry), T2 (T2080/T2081, mid-range octal-thread), and T4 (T4240 flagship) tiers; T2081 is positioned as the smaller-footprint, lower-cost variant of the T2080. Key features include four e6500 dual-threaded cores delivering up to 1.5 GHz / 1.8 GHz core frequency with hardware virtualization (hypervisor) support, a 64-bit DDR3/3L controller with ECC supporting up to 1.87 GT/s, two 10 Gigabit Ethernet ports plus additional 1G/2.5G interfaces, integrated SEC crypto acceleration (SEC 5.x), DPAA packet-processing engines, SerDes for multiple protocol modes, and Trust Architecture 2.x secure boot. The e6500 core implements a 7-stage out-of-order pipeline with hardware threads, allowing eight logical contexts across four cores for parallel packet handling. Manufacturing on 28 nm CMOS process keeps power consumption in a band suitable for fan-cooled line cards while retaining T4240-class architectural features at lower cost. Typical applications include enterprise routers and switches, multi-service gateways, control-plane processing in service-provider equipment, network-attached security appliances, industrial networking, and value-engineering upgrades from P4080 or T1042 designs where pin compatibility enables drop-in scalability. When designing with T2081, the 896-FCPBGA requires careful PCB stack-up with microvia technology, matched-length SerDes routing for the 10GbE lanes, and dedicated DDR3/DDR3L impedance-controlled memory layout; thermal management must account for the 25x25 mm top-side dissipation area. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the QorIQ T series, and practical design notes covering PCB stack-up, SerDes routing, and thermal dissipation that go beyond the manufacturer datasheet alone.

USD $171.00 재고 있음

T2081NSE8TTB

T2081NSE8TTB - QorIQ T2 64-bit 8-thread 1.8GHz SoC | NXP

The NXP T2081NSE8TTB is a QorIQ T2 series communications processor built on a 28 nm CMOS process, integrating four dual-threaded PowerPC e6500 cores at up to 1.8 GHz for an effective eight virtual-core platform. The device is delivered in a 780-ball FC-PBGA package (23x23 mm) and supports DDR3/DDR3L memory at up to 1.87 GT/s, two 10 Gigabit Ethernet controllers plus eight 1 Gbps and four 2.5 Gbps interfaces, and an integrated security engine with crypto acceleration enabled. A QorIQ communications processor is a system-on-chip (SoC) designed for high-throughput wired and wireless networking equipment such as routers, switches, base stations, and network-attached storage. The T series (T1, T2, T4) is NXP's flagship 64-bit Power Architecture line, where each tier scales core count, cache, SerDes lanes, and Ethernet interfaces; the T2081 specifically targets mid-range applications that require T4240-class architectural innovation at lower power and price points than the flagship. Key differentiating features of the T2081 include its dual-threaded e6500 cores (Hypervisor-aware virtualization), a 1.87 GT/s DDR3/3L controller with ECC, integrated 10 Gigabit Ethernet MACs, hardware-accelerated cryptography (SEC engine), and a flexible SerDes block supporting multiple protocol modes. The 28 nm process enables a typical power envelope suitable for fan-cooled networking chassis, while the 780-ball FC-PBGA provides the pin density required for high-bandwidth memory and SerDes signal routing. Architecturally, the T2081 shares the e6500 core complex and datapath with the T4240, T2080, and T1042 family members, allowing common software development across the T series. The chip integrates three PCIe controllers, two SATA 2.0 interfaces, two USB 2.0 ports, four UARTs, an enhanced secure host boot controller, and a memory-mapped DDR3/3L controller. Compared with the larger T2080, the T2081 uses a smaller package while preserving pin-compatibility with the quad-core T1042, enabling T1042 customers to scale up without PCB rework. Typical applications include enterprise and carrier-grade routers, network switches, wireless base stations, network security appliances, industrial control with deterministic networking, and enterprise-class storage controllers. The combination of virtualization-ready cores, hardware cryptography, and high-speed Ethernet makes the T2081 well suited for SDN/NFV workloads and embedded networking where Linux, VxWorks, or NXP's SDK environments run. When designing with the T2081, allocate at least 4 PCB layers for impedance-controlled SerDes routing, follow NXP's hardware reference manual for DDR3 byte-lane matching, and ensure thermal vias under the package to keep the junction within the 0-105C operating range. Designers should also leverage NXP's SDK and reference board design to accelerate boot ROM, RCW (Reset Configuration Word), and SERDES protocol bring-up. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not consolidated in any single manufacturer PDF. Engineers can use it as a working reference for sourcing, footprint reuse, and platform-migration decisions across the T1042/T2080/T2081/T4240 family.

USD $222.40 재고 있음

T2081NXE8MQB

T2081NXE8MQB - QorIQ T2 8x 1.2GHz MPU, 2x10GE, Crypto | NXP

The NXP T2081NXE8MQB is a QorIQ T2-series communications processor built on 28 nm CMOS, integrating four dual-threaded 64-bit Power Architecture e6500 cores running at up to 1.2 GHz and packaged in a 780-pin FCPBGA (25x25 mm). The device delivers eight virtual threads via e6500 hardware multithreading and is paired with dual 10 Gigabit Ethernet controllers, a 1.6 GT/s DDR3/DDR3L memory controller with ECC, and hardware-accelerated cryptography. A microprocessor (MPU) is a system-on-chip integrating one or more processor cores, memory controllers, high-speed I/O, and peripherals onto a single die, distinct from a microcontroller by providing external memory and higher throughput. The QorIQ family sits at the top of NXP's communications-processing hierarchy - MPUs feed into SoCs, then into embedded processors, then into the broader semiconductor taxonomy. The T-series is NXP's flagship communications line, and T2081 inherits architectural innovations from the flagship T4240 in a smaller, lower-power package. Key features include 8 virtual cores (4 cores x 2 threads), 1.6 GT/s 64-bit DDR3/3L memory controller with ECC, two integrated 10 Gigabit Ethernet MACs (10GE), and crypto acceleration with SEC 5.x engines. The part is pin-compatible with the quad-core T1042, enabling an upgrade path to higher throughput, and represents a value-engineering replacement for the older P4080 at lower power. Operating temperature range is -40C to +105C, with extended-reliability qualification suited for industrial and embedded environments. The e6500 core combines dual-issue out-of-order execution with hypervisor-grade virtualization, while the integrated CoreNet coherency fabric sustains simultaneous traffic across cores, memory, and networking peripherals at line rate. SEC 5.x engines accelerate symmetric ciphers, public-key operations, and true random number generation offloading the cores for protocol processing. Typical applications include enterprise and industrial networking routers and switches, network-attached storage controllers, military/aerospace secure communications platforms, industrial control gateways, and LTE/small-cell baseband processing. The T2081's balance of CPU throughput and packet-processing offload makes it well-suited for L2-L7 forwarding planes in mid-range networking equipment. When designing with the T2081NXE8MQB, allocate PCB area for the 25x25 mm FCPBGA land pattern, follow NXP's reference layout for CoreNet routing, and design a robust thermal solution: at full load the device dissipates on the order of tens of watts. Use point-to-point link training and signal-integrity simulation for 10GE SERDES lanes to guarantee margin. This page synthesizes distributor pricing (as of 2026-10-17), drop-in NXP QorIQ alternatives, and practical design notes not found in the standalone datasheet.

USD $215.50 재고 있음

T2081NXE8PTB

T2081NXE8PTB - QorIQ T2 4-Core 1.533GHz PowerPC MPU | NXP

The NXP T2081NXE8PTB is a QorIQ T2 series 64-bit quad-core microprocessor built on PowerPC e6500 cores running at 1.533 GHz, housed in a 896-pin FCPBGA (25x25 mm) package. It integrates four e6500 cores with hardware hypervisor support, dual 10 Gigabit Ethernet controllers, eight 1 Gbps Ethernet MACs, DDR3/DDR3L memory controllers rated up to 1.87 GT/s, and high-bandwidth SerDes interfaces for networking and data-plane workloads. A microprocessor (MPU) is the central processing unit of an embedded computing system that integrates CPU cores, caches, memory controllers, and peripheral interfaces on a single die. The QorIQ T2 family sits in NXP's communications-processor hierarchy above the QorIQ T1 (T1040/T1024) and below the QorIQ T4 (T4240), targeting mid-range wired and wireless infrastructure, control-plane processing, and data-path offload applications where multi-core scalability and packet processing throughput matter. Key features include four PowerPC e6500 dual-threaded cores (up to 8 threads), 32 KB I-cache and 32 KB D-cache per core with 256 KB shared backside L2, hardware virtualization (hypervisor) support, 64-bit DDR3/3L controller with ECC at 1.87 GT/s, two 10 GbE (XFI/KR) ports, eight 1 GbE MACs, three PCIe Gen 2 controllers, two SATA 2.0 ports, two USB 2.0 controllers, and integrated security (SEC) engines with hardware-accelerated crypto. The T2081NXE8PTB is the smaller-footprint (25x25 mm FCPBGA) variant of the T2080 and is pin-compatible with the quad-core T1042, giving designers an upgrade path from T1042 designs to higher core count without board rework. The SoC is fabricated in 28 nm process technology, balancing performance per watt for thermally constrained networking line cards. Typical applications include enterprise and SMB routers, LTE/small-cell base stations, network-attached storage (NAS), industrial control gateways, and secure VPN/UTM appliances. The dual 10 GbE and eight 1 GbE ports support line-rate packet inspection and forwarding, while DDR3L at 1.87 GT/s sustains deep packet buffer and routing table lookups. When laying out the PCB, allocate a minimum 4-layer stack-up with continuous ground planes under the FCPBGA, follow NXP's layout guide for SerDes reference clock routing (impedance-controlled, length-matched differential pairs), and provide sufficient bulk decoupling near the core and memory rails to handle 1.533 GHz load transients during packet bursts. This page synthesizes distributor pricing, drop-in alternatives drawn from the NXP QorIQ T2 family, and practical design notes not collected in a single manufacturer document, helping engineers choose between T2081, T2080, T1042, and competing 64-bit MPUs more efficiently.

USD $198.00 재고 있음

T2081NXN8MQB

T2081NXN8MQB - QorIQ 4-Core 1.2GHz MPU BGA | NXP

NXP Semiconductors T2081NXN8MQB is a QorIQ communications processor built on 64-bit Power Architecture with four e6500 dual-threaded cores running at 1.2 GHz, giving eight virtual threads in total. Per NXP's QorIQ T2 family positioning, the T2081 is the smaller-package variant of the T2080 flagship, pin-compatible with the quad-core T1042 for easy performance scaling. The device integrates dual 10 Gigabit Ethernet MACs, a DDR3/3L memory controller rated to 1.6 GT/s with ECC, hardware-accelerated pattern matching, and SerDes supporting multiple interface protocols. This part belongs to the QorIQ T series of communications processors, a category of 64-bit Power Architecture multicore SoCs targeting networking, industrial control, and military/aerospace platforms. Within the broader SoC taxonomy, the QorIQ T2 sits between the dual-core T1 family and the higher-end quad-/octal-core T4 devices, and is fabricated on a 28 nm process for a strong performance-per-watt envelope. Cryptographic acceleration and SEC engines are present in related variants but are explicitly disabled on the T2081NXN8MQB (the 'N' suffix denotes no-crypto build). Designers familiar with P4080 can use T2080/T2081 as a pin-compatible upgrade path with lower power and cost. Key features include four e6500 cores at 1.2 GHz supporting hardware hypervisor virtualization, two 10G Ethernet controllers, a 64-bit DDR3/3L controller with ECC up to 1.6 GT/s, two PCIe controllers, and a 780-ball FCBGA package (25x25 mm). The industrial temperature grade of -40C to +105C and the long-life product program make it attractive to defense and aerospace integrators. Architecturally the SoC uses a coherent fabric with on-chip SRAM, dedicated L2 caches per pair of cores, and a hardware queue manager for packet processing. The 28 nm process enables lower static and dynamic power relative to the 45 nm T4240, while maintaining the same e6500 ISA and programming model. Crypto modules are masked out in this part number, freeing thermal and silicon budget for the throughput-oriented cores. Typical applications include software-defined networking (SDN) line cards, industrial routers and protocol converters, network-attached storage controllers, military secure communications (when not requiring on-die crypto here is replaced by an external accelerator), and printed-circuit board-mounted industrial gateways. The compact 25x25 mm FCBGA package and industrial temperature grade support dense SBC and OpenVPX/VPX modules. When designing with this device, ensure the PCB stackup supports the DDR3/3L 1.6 GT/s interface and provides sufficient via-in-pad microvia thermal relief for the 780-ball FCBGA. Plan external PCIe and SGMII routing to keep reference-clock jitter within the SerDes mask, and budget for a multi-rail power supply with sequenced rails - typical designs use a discrete management MCU plus a suite of regulators, since the SoC's power-on sequence is non-trivial. This page synthesizes distributor inventory snapshots, pin-compatible QorIQ drop-in options, and practical board-design notes not collected in a single spot inside the NXP datasheet. It is intended as a complementary engineering reference.

USD $318.50 재고 있음

T4080NSE7PQB

T4080NSE7PQB - QorIQ T4 8-Core 1.5GHz Power Arch MPU | NXP

The NXP T4080NSE7PQB is a QorIQ T4 series multi-core communications processor integrating 8 virtual cores (4 physical e6500 cores with hardware multithreading) running at up to 1.5 GHz on a 64-bit Power Architecture, packaged in a 1932-ball FCPBGA (45x45 mm) with operating temperature 0C to 105C and silicon revision 2.0. What is a QorIQ communications processor? A QorIQ processor is a high-end Power Architecture system-on-chip (SoC) family from NXP designed for networking infrastructure such as routers, switches, base stations, and security appliances. QorIQ belongs to the broader category of embedded MPUs (microprocessor units), which are microprocessors designed for non-desktop applications like industrial control, networking, and storage. Within that hierarchy QorIQ sits at the top alongside other networking SoCs from Broadcom, Cavium/Marvell, and Intel Xeon-D processors, offering integrated high-speed serial interfaces, hardware acceleration engines, and ECC-protected memory controllers in a single BGA package. Key features include the e6500 dual-threaded Power Architecture core complex delivering up to 1.5 GHz per thread, dual 10 Gigabit Ethernet controllers, a DDR3L memory controller with speeds up to 1.6 GT/s, integrated cryptographic and pattern-matching accelerators, and SerDes lanes for multiple high-speed interconnect standards. The 1932-FCPBGA package provides sufficient routing density and thermal mass for sustained industrial-temperature operation while exposing the full QorIQ T4 platform I/O. The T4080 implements NXP's Data Path Acceleration Architecture (DPAA) and CoreNet fabric, which offload queue management, buffer allocation, and security processing from the cores. This allows line-rate packet processing at 10 GbE and 40 GbE aggregate throughput while keeping the cores available for control-plane workloads. Hardware virtualization, extended MMU translation, and ECC on all memory interfaces make the part suitable for virtualized network functions and trusted execution environments. Typical applications include enterprise and service-provider routers, multi-service switches, network-attached storage controllers, LTE base-station baseband units, and network security appliances. The T4080 pairs with companion NXP QorIQ devices such as the T4240 (24 virtual cores) for slot aggregation and the T4160 (16 virtual cores) for mid-range routing line cards. Designers should plan thermal management around a TDP-class dissipation budget and follow NXP reference design guidelines for CoreNet and SerDes layout to achieve the rated 1.6 GT/s DDR3L performance. The Rev 2.0 silicon is the current production stepping and is required for full feature support including the integrated crypto engine and pattern-matching accelerator. This page synthesizes distributor pricing, QorIQ T4 family cross-reference, and BGA-level design notes that are not consolidated in any single manufacturer document.

USD $295.00 재고 있음

T4080NSE7QTB

T4080NSE7QTB - QorIQ T4 8-Core 1.8GHz PowerPC MPU | NXP

The NXP T4080NSE7QTB is a QorIQ T4 family communications processor based on the 64-bit Power Architecture e6500 core, integrating 8 hardware threads operating at up to 1.8 GHz in a 1932-ball FCBGA (45x45 mm) package with industrial 0-105C thermal range. A communications processor (CP) is a specialized microprocessor designed for networking and telecom infrastructure where deterministic packet processing, high memory bandwidth, and integrated high-speed serial interfaces replace the general-purpose peripherals found on application processors. Within the broader taxonomy it belongs to the QorIQ family of Power Architecture SoCs, positioned between application processors and pure network ASICs. The T4 line covers 8 to 24 virtual cores in a single pin-compatible package, enabling one PCB design to scale across multiple SKUs. Key features include 8 hardware threads on 4 physical e6500 cores, dual 10 Gigabit Ethernet controllers, integrated security (crypto enabled), DDR3L memory controller with 1.87 GT/s data rate per the verified distributor datasheet string, and silicon revision 2.0. The e6500 core introduces hardware hypervisor support and out-of-order execution tailored for control-plane and data-plane packet handling. From an architecture standpoint the device combines the e6500 superscalar core, CoreNet coherency fabric, data path acceleration (DPAA), and SerDes lanes that map directly to networking PHYs. The 1.87 GT/s DDR3L controller supports registered ECC DIMMs, critical for sustained line-rate forwarding on hot packet flows. Typical applications include enterprise routers, Layer 2/3 switches, network security appliances, LTE baseband offload, and edge compute platforms where deterministic multi-core throughput is required. When designing with this device, ensure adequate thermal management: the 45x45 mm FCBGA exposes a thermal interface pad for a heatsink or cold plate. Power sequencing and DDR3L termination must follow the QorIQ T4 hardware specification. This page synthesizes distributor pricing, pin-compatible alternatives, and design considerations not found in the manufacturer datasheet alone.

USD $695.00 재고 있음

T4080NXE7PQB

T4080NXE7PQB - QorIQ T4080 4-Core 1.8GHz PowerPC MPU | NXP

The NXP T4080NXE7PQB is a QorIQ T4080 communications microprocessor built on the 64-bit PowerPC e6500 core architecture, integrating 4 physical cores (8 threads via SMT) at up to 1.8 GHz in a 1932-pin FCBGA (45x45 mm) package. It supports DDR3/DDR3L memory with up to 1.6 GT/s data rate, integrates 13 Gigabit Ethernet MACs plus two 10 Gigabit Ethernet interfaces, and includes hardware-accelerated cryptography and pattern matching engines for security and deep-packet inspection. A communications microprocessor (MPU) is a high-performance system-on-chip designed for wired and wireless networking infrastructure, replacing the CPU, northbridge, and large portions of I/O logic in a single device. MPU sits above the microcontroller in the embedded taxonomy: microcontroller -> embedded MPU -> application processor -> SoC. QorIQ devices sit in the networking/datacom tier and are typically paired with PHYs, switch fabrics, SERDES, and external memory. The T4080NXE7PQB key features include: 4 e6500 cores with hardware multithreading (8 logical threads), 64-bit datapath, 28nm process technology, integrated 1 Gbps Ethernet MACs, 10 Gbps XAUI/KR interfaces, hardware crypto (SEC), L2 and L3 cache, virtualization (hypervisor) support, Trust Architecture, and the QorIQ Data Path Acceleration Architecture (DPAA) for packet parsing and QoS. The e6500 core is a superscalar out-of-order dual-threaded core using the Book-E instruction set plus AltiVec SIMD, with a private L1 cache per thread and a shared L2/L3 hierarchy. DPAA offloads buffer management and queue scheduling, freeing the cores to run control-plane software such as routing stacks (Linux, VxWorks, eCos) or protocol stacks (IPsec, SSL/TLS). Typical applications include enterprise routers, service-provider edge and aggregation routers, 3G/4G/LTE base stations, network security appliances (firewall/UTM/IDS), IP-PBX, industrial Ethernet gateways, and software-defined networking (SDN) controllers. The 1.6 GT/s DDR3L controller with ECC is essential for sustained packet throughput, while 13x GbE plus 2x 10GbE enables dense multi-port fan-out. Design consideration: the 1932-pin FCBGA requires a high-density PCB build (microvias, HDI, controlled-impedance SERDES routing) and a solid power-delivery network. Power, thermal, and SI co-design are mandatory at 1.8 GHz. Use JEDEC -40C to +105C ambient under extended industrial airflow. This page synthesizes distributor pricing, pin-compatible T4-family alternatives, and practical design notes not collected on any single distributor or manufacturer page, giving engineers a single source for selection, qualification, and sourcing decisions.

USD $1,485.00 재고 있음

T4160NSE7QTB

T4160NSE7QTB - QorIQ T4 8-Core 1.8GHz PowerPC SoC | NXP

The NXP Semiconductors (formerly Freescale) T4160NSE7QTB is a QorIQ T4 series multi-core communications processor featuring 8 PowerPC e6500 cores operating at up to 1.8 GHz, delivering 16 hardware threads via Simultaneous Multi-Threading (SMT), housed in a 1932-ball FCPBGA package measuring 45x45 mm with a 0.8 mm pitch. The SoC integrates dual 10 Gigabit Ethernet controllers plus 13 Gigabit Ethernet ports and a DDR3/DDR3L memory controller capable of 1.87 GT/s operation, with hardware-accelerated cryptography enabled for secure boot and IPsec/TLS workloads. A QorIQ communications processor is a system-on-chip (SoC) designed for high-performance networking infrastructure such as routers, switches, security appliances, and wireless base stations. Positioned in the broader taxonomy, the QorIQ family belongs to the power architecture communications processor segment, sitting between standard embedded microcontrollers and high-end server CPUs, optimized for deterministic packet processing, deep pipeline acceleration, and tight integration of networking peripherals. Within the T-series lineup, the T4 family spans the T4080 (8 threads), T4160 (16 threads), and the flagship T4240 (24 threads), all sharing a pin-compatible package to enable scalable product lines. Key features include eight PowerPC e6500 cores with dual-thread SMT, integrated DPAA (Data Path Acceleration Architecture) for hardware offload of packet parsing, queueing, and crypto, an SEC engine for symmetric and asymmetric cryptography, and dual PCIe Gen 2 controllers. The device targets 0 to 105 degrees C extended temperature operation suitable for industrial networking equipment, supports Trust Architecture 2.0 secure boot, and provides SerDes lanes configurable for SGMII, XAUI, KR, and PCIe. The T4160NSE7QTB employs the e6500 Power Architecture core with 64-bit datapath, superscalar out-of-order execution, and AltiVec-compatible SIMD engine for data-plane workload acceleration. The integrated CoreNet coherency fabric interconnects cores, memory controller, and I/O blocks, delivering high bandwidth with low latency. Memory controller supports DDR3 and DDR3L at 1.87 GT/s with ECC, providing up to 64-bit wide interfaces. The crypto engine delivers line-rate IPSec, SSL/TLS, and SRTP processing without CPU intervention. Typical applications include enterprise routers and switches, network attached storage (NAS), 4G/LTE small cells, IPsec VPN gateways, network functions virtualization (NFV) platforms, and industrial control planes. The T4160 fits workloads requiring multi-Gbps throughput combined with deterministic control-plane latency and hardware-accelerated security. When designing with this device, plan the PCB layout for the large 45x45 mm FCPBGA package with proper microvia stack-up and at least 8 signal layers for SerDes routing. Use NXP's QorIQ SDK and CodeWarrior toolchain for firmware development. Allocate sufficient cooling for typical 30-45 W power dissipation, and validate DDR3L signal integrity with IBIS-AMI simulation before tape-out.

USD $640.00 재고 있음

T4160NSE7TTB

T4160NSE7TTB - QorIQ T4 8-Core 1.8GHz Power Arch MPU | NXP

The NXP T4160NSE7TTB is a QorIQ T4 series 64-bit Power Architecture microprocessor with 8 physical cores (16 threads via simultaneous multithreading) running at 1.8 GHz, housed in a 1932-ball FCPBGA (45x45 mm) package. It integrates 4x 10 Gigabit Ethernet controllers, a DDR3L memory controller supporting up to 1.8 GT/s data rate, and hardware-accelerated cryptography, and is specified for the commercial 0 to 105 C temperature range. A microprocessor (MPU) is the central processing unit of an embedded system, integrating one or more processor cores, cache hierarchies, memory controllers, and a wide range of on-chip peripherals. QorIQ communications processors extend the MPU concept into networking and telecom infrastructure, combining general-purpose compute with hardware accelerators for packet processing, security, and high-speed SerDes. The T4 series sits in NXP's mid-to-high tier of the QorIQ roadmap, below the flagship T4240 (12 cores/24 virtual cores) and above the T2081 (4 cores). Key features of the T4160NSE7TTB include the e6500 core with AltiVec SIMD support, hardware pattern matching and traffic management accelerators, integrated SEC crypto engine, and dual-core memory subsystem with 64-bit DDR3L interface. The SerDes block supports 4x 10G plus multiple lower-speed lanes, enabling line-rate processing for enterprise and service-provider routers. Architecturally, the T4160 is built on a 28 nm process with a coherent shared-memory fabric across all cores, allowing symmetric multiprocessing across the 16 threads. Each pair of cores shares a private L2 cache, and a shared L3 cache backs the coherent bus, reducing DDR traffic for typical networking workloads. Typical applications include enterprise routers, service-provider edge equipment, network-attached storage controllers, industrial IoT gateways, and security appliances that require multi-gigabit throughput with hardware crypto offload. The part's combination of 16 threads and integrated 10 GbE makes it well suited for control- and data-plane co-processing in a single SoC. When designing with the T4160NSE7TTB, pay close attention to PCB layout: the 1932-ball FCPBGA requires high-density routing with microvia or sequential lamination stack-ups, and the integrated SerDes lanes need controlled-impedance routing with reference-plane continuity to meet 10.3125 Gbps signaling margins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer's product page alone.

USD $1,390.00 재고 있음

T4160NSN7QTB

T4160NSN7QTB - QorIQ 16x 1.67GHz SoC, 2x10GE, FCBGA-1932 | NXP

The NXP T4160NSN7QTB is a 64-bit multi-core communications processor from the QorIQ T4 family, featuring 16 virtual cores based on the Power Architecture at 1.67 GHz, integrated dual 10 Gigabit Ethernet MACs, a DDR3L memory controller rated at 1.87 GT/s, and 1932-ball FCBGA packaging with industrial 0°C to 105°C thermal support and crypto features disabled. The part is positioned as the mid-tier SKU of the pin-compatible T4080/T4160/T4240 family, offering a 2x core-count step from the T4080 and a balanced power-performance profile for networking line cards and control plane workloads. A communications SoC is a system-on-chip that integrates CPU cores, memory controllers, packet-processing accelerators, and high-speed serial interfaces into a single device. Within the NXP product hierarchy the T4160 belongs to the QorIQ family, which sits in the broader category of Power Architecture (PowerPC/e600) embedded processors used primarily in networking equipment. The T4160NSN7QTB extends the line into the 16-thread segment, serving designs that need more compute than T4080-based boards but less power than the 24-thread T4240 flagship. Key features include 16 e6500 Power Architecture virtual cores (eight dual-threaded physical cores), 1.67 GHz core frequency with frequency scaling up to 1.8 GHz supported in the family, two integrated 10 Gigabit Ethernet (10GE) controllers, a 64-bit DDR3L memory controller at up to 1.87 GT/s, and Data Path Acceleration Architecture (DPAA) for inline packet parsing, queue management, and cryptographic acceleration. The FCBGA-1932 package provides the high-bandwidth interconnect required for 10GE-class networking products. The T4160NSN7QTB is built on a 45 nm CMOS process and shares a pin-compatible FCBGA-1932 footprint with the T4080 (8 threads), T4240 (24 threads), and the low-power T4161/T4081/T4241 variants, allowing a single PCB design to be deployed at three performance points. The DPAA engine and tightly coupled core complex are designed for deterministic throughput on packet pipelines where cache misses and arbitration delays are unacceptable. Typical applications include multi-service routers and switch control planes, enterprise and edge firewalls, LTE/4G base station baseband processing, network-attached storage controllers, and unified threat management appliances. The dual 10GE MACs and DDR3L bandwidth make it well suited to aggregated traffic workloads where packet header processing dominates. Design considerations include careful PCB stack-up planning because the FCBGA-1932 has a 1.0 mm pitch and high-speed DDR3L routing for byte lanes with matched impedance and length; designers must follow NXP's hardware design guide for decoupling, SerDes reference clock jitter, and thermal management under sustained DPAA loads. This page consolidates distributor pricing, NXP part-numbering interpretation, drop-in T4-family alternatives, and engineering design notes that go beyond the manufacturer's official datasheet to assist board-level architects.

USD $770.00 재고 있음

T4160NSN7TTB

T4160NSN7TTB - QorIQ 16-Core 1.8GHz Power Arch MPU | NXP

The NXP (formerly Freescale) T4160NSN7TTB is a QorIQ T4-series communications microprocessor built on a 64-bit Power Architecture e6500 core complex, delivering 16 hardware threads across 8 dual-threaded cores at up to 1.8 GHz, in a 1932-ball FC-PBGA package (45x45 mm). It is the 16-thread member of the T4 family, pin-compatible with the 24-thread T4240 and 8-thread T4080 within a 3x performance scaling envelope. What is a QorIQ communications processor? A QorIQ processor is a multi-core Power Architecture microprocessor designed by NXP for networking and data-plane workloads such as routers, switches, wireless baseband, and security appliances. As a category, QorIQ sits in the hierarchy: microprocessor unit (MPU) -> embedded processor -> communications processor -> networking SoC. The T4 family targets high-end control-plane and data-plane processing for terabit-class routers, service-provider gateways, and network-attached storage. Key features of the T4160NSN7TTB include a 1.8 GT/s DDR3L memory controller with ECC, integrated 4x 10 Gigabit Ethernet (10GE) plus 8x 1 Gigabit Ethernet (1GE) SerDes lanes, hardware cryptography disabled in this -NS suffix (T4160NS variant), and operating junction temperature support of 0C to 105C in Rev 2.0 silicon. The device integrates packet-processing acceleration engines, a high-bandwidth CoreNet coherency fabric, and extensive I/O including PCIe, SATA, and USB. Architecturally, the e6500 cores support hardware multithreading (SMT), out-of-order execution, and AltiVec SIMD, with a triple-issue superscalar pipeline. The CoreNet coherency fabric ensures coherency across cores and accelerators at high throughput, while the memory subsystem delivers 1.8 GT/s aggregate bandwidth to feed 16 threads without contention. Crypto variants (T4160NSN7TTB's crypto-disabled sibling T4160NSE) integrate SEC engines for IPsec and SSL offload. Typical applications include enterprise routers, service-provider edge platforms, network security appliances, LTE/WCDMA baseband processing, and high-end network-attached storage (NAS) controllers. The 16-thread configuration balanced against 10GE+1GE SerDes makes it well-suited to mid-range multi-service aggregation platforms. When designing with the T4160NSN7TTB, ensure the PCB land pattern uses the 45x45 mm FC-PBGA with a 16-layer or higher stack-up to manage the 1.8 GT/s DDR3L signals with matched impedance. Reference the NXP hardware design checklist for decoupling, SerDes routing, and thermal management. This page synthesizes distributor pricing, drop-in NXP T4-family alternatives, and design considerations not found in the manufacturer datasheet alone.

USD $1,395.00 재고 있음

T4160NXN7PQB

T4160NXN7PQB - QorIQ 16-Core 1.5GHz SoC | NXP Semiconductors

The NXP T4160NXN7PQB is a 64-bit Power Architecture QorIQ T4 family multicore communications processor with 16 virtual cores running at 1.5 GHz, housed in a 1932-pin FCPBGA (45x45 mm) package. It integrates a dual-channel DDR3L memory controller with up to 1.6 GT/s data rate, dual 10 Gigabit Ethernet MACs, and SerDes for high-speed I/O, with hardware cryptography disabled in this revision (Rev 2.0). Industrial temperature grade is -40C to +105C. A multicore communications SoC (System-on-Chip) is a single silicon die that integrates CPU cores, memory controllers, networking accelerators, and I/O subsystems onto one chip. The QorIQ family is built on the 64-bit Power Architecture (formerly PowerPC) instruction set, scaled for embedded networking and industrial workloads. The T4 family spans T4080 (8 threads), T4160 (16 threads), and T4240 (24 threads) in a pin-compatible package, giving designers a 3x performance scaling path on one PCB. Key features include 16 threads (8 dual-threaded e6500 cores) at 1.5 GHz, 1.6 GT/s DDR3L with ECC, two 10 Gigabit Ethernet interfaces, hardware cryptography disabled, and extended temperature operation to +105C. The 28nm process gives improved performance-per-watt versus earlier QorIQ generations, while preserving software compatibility across the T4 series. The T4160NXN7PQB ships as a tray-packaged part intended for high-density networking and industrial computing platforms. The architecture combines out-of-order Power Architecture cores with a coherent CoreNet fabric, enabling efficient parallel packet processing. The SerDes block supports multiple protocols including XAUI, XFI, KR, and SGMII, allowing direct connection to 10G/1G PHYs without external glue logic. Hardware accelerators offload pattern matching, CRC, and queue management, dramatically reducing CPU load in deep-packet-inspection workloads. The integrated security engine is present but disabled in this part revision - derivative SKUs with crypto enabled exist for adjacent use cases. Typical applications include enterprise routers and switches, network appliances, industrial control gateways, telecom base-station controllers, and aerospace/defense packet processors. The 16-thread configuration is well-suited to mid-range networking workloads - heavy enough for line-rate 10G processing yet within the power envelope of passively-cooled industrial chassis. When designing with this device, allocate a multi-layer PCB with at least 8 layers for signal integrity across the high-speed SerDes and DDR3L interfaces. The 1932-ball FCBGA requires a substrate with microvia stack-ups and matched-length routing. Thermal management must consider the 1.5 GHz core clock under sustained load - a heatsink and airflow path are required at industrial temperatures above +85C. This page synthesizes distributor pricing from Mouser and DigiKey Marketplace, NXP family-level alternative guidance, and practical layout guidance for the FCBGA-1932 footprint - information that complements the official QorIQ T4 datasheet without replacing it.

USD $285.50 재고 있음

T4240NSE7PQB

T4240NSE7PQB - 24-Core QorIQ Power Arch SoC | NXP

The NXP T4240NSE7PQB is the flagship QorIQ T4 series communications processor with 24 virtual cores based on the 64-bit Power Architecture e6500 core, running up to 1.5 GHz (1.8 GHz capable), in a 1932-ball FCPBGA package (45x45 mm). It integrates 1.6 GT/s DDR3L memory controllers and four 10 Gigabit Ethernet (10GE) MACs with classified security/crypto acceleration enabled, operating across the 0 to +105C industrial junction temperature range, with silicon revision 2.0. The device is built in a 45 nm SOI CMOS process and targets line-rate packet processing across enterprise, service-provider, and data-center networking infrastructure. A QorIQ multiprocessor is a multi-core system-on-chip (SoC) tailored for data-plane workloads such as routing, switching, security, and protocol termination. Within the broader taxonomy, QorIQ belongs to the communications processor (CP) family, which sits hierarchically below general-purpose microprocessors and above single-core MCUs. Its core advantages are deterministic throughput on parallel threads (24 hardware threads via the e6500 dual-threaded core), tight integration of packet I/O, memory controller, and acceleration engines, and an extended lifecycle suited to embedded networking OEMs. Key features include 24 virtual cores delivered by 12 physical e6500 dual-threaded cores, an integrated memory subsystem supporting DDR3L at up to 1.6 GT/s with ECC, an integrated security engine (SEC) at up to 10 Gbps for IPsec, SSL/TLS, and SRTP, four 10G plus multiple 1G Ethernet controllers with hardware L2 switching and classification, and an Enhanced Triple Speed Ethernet (eTSEC) peripheral complement. The device also offers four PCIe Gen2 controllers, RapidIO, and a complete set of peripheral I/O for system integration. The T4240 implements a coherent shared-memory architecture with the CoreNet coherency fabric, allowing all 12 dual-threaded cores to share L2 caches and the integrated 1 MB L2 per cluster. The platform's 64-bit Power Architecture ISA, hardware hypervisor extensions, and dedicated resource partitioning make it suitable for multi-tenant virtualized networking appliances. Typical applications include top-of-rack and spine switches, enterprise routers with 10G/40G uplinks, network security appliances (firewalls, UTM, IPS/IDS), wireless infrastructure controllers, and data-center server/load balancers. Its 24-thread envelope is particularly well suited to software-defined networking (SDN) control plane plus line-rate classification workloads. When designing with this device, allocate ample PCB real estate for the 1932-ball FCPBGA, follow NXP's reference design for power sequencing and SerDes reference clock jitter, and provision at least 8-layer PCB with controlled-impedance routing for the 10G KR lanes to meet IEEE 802.3ap compliance. This page synthesizes distributor pricing, drop-in same-package alternatives from the T4 family, and practical design considerations beyond the manufacturer datasheet summary.

USD $680.00 재고 있음

하위 카테고리

제품 (31127)