집적 회로

하위 카테고리

📁 ADC/DAC 3,100+ 제품 📁 증폭기 IC 1,900+ 제품 📁 오디오 코덱 18 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 660+ 제품 📁 Comparator ICs 1 제품 📁 DSP 1,100+ 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 7,300+ 제품 📁 인터페이스 IC 3,300+ 제품 📁 LED 드라이버 1 제품 📁 로직 IC 460+ 제품 📁 메모리 IC 870+ 제품 📁 마이크로컨트롤러 20,000+ 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 14 제품

제품 (39,000+)

OPA177GP - 25uV Precision Op Amp | Texas Instruments
OPA177GP

OPA177GP - 25uV Precision Op Amp | Texas Instruments

The Texas Instruments OPA177GP is a precision bipolar operational amplifier with 25 uV maximum input offset voltage, 0.3 uV/°C maximum offset drift, 130 dB minimum open-loop gain, and 1.5 mA typical quiescent current in an 8-pin PDIP package. It combines low input error with low-noise performance for precision signal conditioning. A precision operational amplifier is a voltage-amplifier IC designed to minimize input offset voltage and its temperature-dependent drift. This low-error capability places the OPA177GP within the operational-amplifier hierarchy of analog signal-chain ICs, where accurate amplification of small sensor, reference, or measurement signals is more important than high output-current capability. Its bipolar architecture also provides continuous operation without the periodic ripple and frequency artifacts associated with chopper-stabilized amplifiers. The principal features of the OPA177GP include 25 uV maximum offset voltage, 0.3 uV/°C maximum voltage drift, and 130 dB minimum open-loop gain. Its 1.5 mA typical quiescent current supports power-conscious precision systems when the signal bandwidth and load requirements are moderate. The manufacturer identifies the device as a low-noise bipolar operational amplifier and describes it as an effective alternative to chopper-stabilized amplifiers. The combination of low offset, low drift, and high open-loop gain improves closed-loop accuracy in amplifier configurations where gain and feedback resistors establish the nominal gain. High open-loop gain reduces the contribution of input-referred error to the output, while low offset drift limits calibration changes over temperature. Because the OPA177GP uses a bipolar input stage, engineers can evaluate its bias-current and noise characteristics against the source impedance and bandwidth of the selected sensor or signal source. Typical uses include precision instrumentation, low-level sensor signal conditioning, current measurement, laboratory equipment, and analog signal buffers. It is also suitable for applications requiring accurate DC amplification without the periodic output disturbance of a chopper-stabilized amplifier. The 8-pin PDIP package is appropriate for through-hole prototype, industrial control, and test-equipment layouts where sufficient board space is available. When designing around the OPA177GP, verify the complete electrical limits, supply range, common-mode range, output swing, and stability conditions in the manufacturer datasheet. Input bias-current return paths, source impedance, feedback resistance, and output loading can materially affect accuracy and noise. Decoupling should follow the application guidance in the manufacturer data sheet, and unused inputs should be handled according to the recommended circuit arrangement. This page combines the OPA177GP operating characteristics, a documented drop-in comparison with the Analog Devices OP177, and practical guidance for precision amplifier selection. It helps engineers distinguish offset, drift, gain, noise, and packaging considerations before committing a high-accuracy analog design to a through-hole operational-amplifier footprint.

견적 요청 문의하기
OPA189ID - 14MHz Zero-Drift Precision Op Amp, 36V | Texas Instruments
OPA189ID

OPA189ID - 14MHz Zero-Drift Precision Op Amp, 36V | Texas Instruments

The Texas Instruments OPA189ID is a single, 14-MHz, mux-friendly, low-noise, zero-drift, rail-to-rail-output CMOS precision operational amplifier packaged in an 8-pin SOIC (D) body. It supports operation up to 36 V total supply, swings the output to plus or minus 18 V, and delivers 0.4 uV of input offset voltage with 0.005 uV/degC of offset drift. A zero-drift amplifier is an operational amplifier whose offset voltage and offset drift are continuously corrected by an internal chopping/auto-zero style system rather than by ordinary temperature compensation alone. In the wider hierarchy it sits as a precision amplifier inside the operational amplifier class, which in turn belongs to the analog IC and signal-conditioning chain. Because the residual offset stays in the nanovolt-to-sub-microvolt range over temperature, zero-drift devices are the preferred building block for current sensing, bridge instrumentation, and sensor front ends where long-term calibration drift matters more than raw bandwidth. Key features of the OPA189 include a 14 MHz gain-bandwidth product, a mux-friendly input architecture that tolerates large differential input swings before saturation, rail-to-rail output operation for maximum output swing on the supply rails, ultra-low offset voltage of 0.4 uV, and offset drift of only 0.005 uV/degC. Because it is a CMOS design, input bias current stays very low, and the controlled start-up system provides repeatable power-up behavior for precision systems. Internally, the amplifier combines a zero-drift input stage with a conventional wide-band output stage. The result is fast settling and 14 MHz of small-signal bandwidth while the DC error terms remain near the chopping-noise floor. The MUX-friendly input stage uses internal protection structures that keep the amplifier in its linear region even when several microvolts-to-millivolts of differential signal appears during multiplexer switching, which removes the need for external series resistors between the mux and the amplifier. Typical uses include current-shunt and power-supply sense amplifiers, 16-to-24-bit SAR and delta-sigma analog front ends, resistive sensor bridges, precision current measurement for motor control, and low-noise signal chains in instrumentation and test equipment. It also suits audio and communication receive chains that need low noise plus good DC stability. When designing with the OPA189ID, remember that the output swings rail-to-rail but the input common-mode range and bias current are specific per device; check the manufacturer datasheet before operating near the rails. Provide standard supply decoupling and respect the minimum supply voltage, and route the feedback network away from noisy switching nodes. This page combines package, pricing, cross-reference and drop-in replacement data with practical design notes that go beyond the manufacturer datasheet.

견적 요청 문의하기
OPA192ID - 36V Precision Rail-to-Rail Op Amp | Texas Instruments
OPA192ID

OPA192ID - 36V Precision Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments OPA192ID is a single-channel, high-voltage precision operational amplifier with rail-to-rail input and output, designed for accurate signal conditioning across a wide supply range. Its key characteristics include ±5 µV typical offset voltage, ±0.2 µV/°C typical offset-voltage drift, 5.5 nV/√Hz input noise at 1 kHz, 140 dB common-mode rejection, and a 10 MHz gain-bandwidth product. The device is supplied in an 8-pin SOIC package for OPA192ID. An operational amplifier is an active analog building block used to amplify, buffer, filter, and compare signals. The OPA192 family belongs to the precision operational-amplifier category, combining low offset, low noise, high common-mode rejection, and broad input and output swing. This combination makes the amplifier useful when a system must preserve small signals while operating across industrial, instrumentation, test, measurement, and control applications. The rail-to-rail input stage accepts signals close to the supply rails, while the rail-to-rail output stage allows the output to approach the available output limits. The low-offset architecture and e-trim calibration support stable DC measurements, while the 10 MHz bandwidth enables signal processing beyond traditional precision-amplifier bandwidth. The 140 dB CMRR helps reject common-mode interference in systems with long signal paths or nearby switching circuitry. OPA192 is suitable for precision measurement, current sensing, sensor conditioning, buffer amplifiers, programmable-gain stages, and low-level analog signal chains. The high-voltage operating capability is useful when the signal or supply range exceeds that of many conventional precision op amps. Designers should still verify input and output limits, load conditions, stability, and thermal limits against the manufacturer datasheet for the selected supply and operating conditions. The OPA192ID package is an 8-pin SOIC. Place input and output components close to the device, provide suitable bypass capacitance near the supply pins, and keep sensitive input traces short and away from switching nodes. For new designs where higher channel density or different packaging is required, the OPA2192 and OPA4192 family members provide dual- and quad-channel options rather than a direct pin-for-pin replacement. This product page combines the manufacturer specifications, package information, application guidance, pricing evidence, and carefully qualified drop-in alternatives for engineers evaluating the OPA192ID.

견적 요청 문의하기
OPA206 - 240uA Low-Noise Precision Op Amp, OVP | TI
OPA206

OPA206 - 240uA Low-Noise Precision Op Amp, OVP | TI

The Texas Instruments OPA206 is a low-power, low-noise precision operational amplifier from the OPAx206 family, combining e-trim(TM) factory calibration with super-beta inputs and integrated input overvoltage protection (OVP) up to 40 V beyond either supply rail, in a standard 8-pin SOIC package. It draws only 240 uA of quiescent current while delivering 8 nV/rtHz broadband noise. A precision operational amplifier is a high-accuracy analog amplifier within the hierarchy of operational amplifiers, amplifier ICs, and analog signal chain semiconductors. Precision op amps minimize DC error sources - input offset voltage, offset drift, and input bias current - so small sensor and reference signals can be amplified faithfully in instrumentation, data acquisition, and control systems. Key features include a maximum input offset voltage of 25 uV (e-trim calibrated), a maximum offset voltage drift of 0.5 uV/degC, and a maximum input bias current of 500 pA enabled by super-beta input transistors. The integrated OVP protects inputs up to 40 V beyond the supplies - a feature few precision op amps offer - eliminating external clamp diode networks that add leakage and noise. The push-pull, rail-to-rail output stage maximizes dynamic range on low supply rails. The OPAx206 family is positioned by TI as the next generation of the industry-standard OPAx277 family, retaining low-drift precision character while adding OVP. E-trim factory trimming removes the dominant offset error at manufacture, achieving temperature stability that discrete trimming cannot easily match. According to the TI datasheet, the family spans single (OPA206), dual (OPA2206), and quad (OPA4206) versions for design scalability. Typical applications include transducer signal conditioning, precision data-acquisition front ends, industrial PLC analog input modules, test-and-measurement instrumentation, and battery-powered precision systems where 240 uA quiescent current conserves power. Supply operation from 4.5 V to 36 V total suits both 5 V single-supply and plus/minus 15 V dual-supply systems. Design consideration: choose the OPA206 when inputs may be exposed to fault voltages; if inputs are inherently protected and minimum noise is paramount, the pin-compatible OPA205 offers slightly better noise without OVP.

견적 요청 문의하기
OPA2107AP - Precision Dual Difet Op Amp 4.5MHz | TI
OPA2107AP

OPA2107AP - Precision Dual Difet Op Amp 4.5MHz | TI

The Texas Instruments OPA2107AP is a precision dual Difet (dielectrically isolated FET) operational amplifier delivering 4.5 MHz gain-bandwidth, 18 V/us slew rate, and 10 pA maximum input bias current in an 8-pin PDIP package, operating from dual supplies of plus/minus 10 V to plus/minus 18 V. An operational amplifier is a high-gain DC-coupled voltage amplifier that, with external feedback networks, forms the core building block of analog signal processing. Within the component hierarchy, the OPA2107AP sits in the precision JFET-input op amp family: operational amplifier -> amplifier IC -> analog integrated circuit. Dual (two-amplifier) packaging halves board area versus two singles, which is why duals dominate multi-channel analog front ends. Key differentiating features per the TI datasheet include very low noise at 10 kHz, low input offset voltage of 1 mV maximum, low offset drift of 10 uV per degree C maximum, and low input bias current of 10 pA maximum. The device is unity-gain stable and offers fast settling to 0.01 percent, making it a direct performance upgrade path for legacy BIFET-type amplifiers such as the classic TL072/TL082 class. Technically, the Difet process uses dielectrically isolated JFET input transistors on a precision bipolar process, combining FET-class input bias currents with bipolar-class output drive and noise performance. The dielectric isolation reduces junction capacitances, enabling the 4.5 MHz bandwidth and 18 V/us slew rate that distinguish this part from slower BIFET designs. Typical applications include data acquisition front ends, DAC output amplifiers, optoelectronic transimpedance stages, and high-impedance sensor interfaces such as photodiode and pH probe amplifiers, where picoampere bias current preserves signal fidelity across megaohm source impedances. Design consideration: as a non-RRIO dual-supply precision amplifier, the input common-mode range does not include either rail; provide at least 2 to 3 V of headroom and place 0.1 uF ceramic decoupling capacitors directly at pins 8 and 4. This page synthesizes verified distributor data, drop-in alternatives, and practical design guidance not consolidated in the manufacturer datasheet.

견적 요청 문의하기
OPA2107AU - Dual 4.5MHz Precision DifET Op Amp | Texas Instruments
OPA2107AU

OPA2107AU - Dual 4.5MHz Precision DifET Op Amp | Texas Instruments

The Texas Instruments OPA2107AU is a precision dual DifET (dielectrically isolated FET) operational amplifier delivering 4.5 MHz gain-bandwidth, 18 V/µs slew rate, and a maximum input bias current of 10 pA in an 8-pin SOIC package operating from ±4.5 V to ±18 V supplies (9 V to 36 V total). An operational amplifier is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of the analog signal chain hierarchy: op amp -> amplifier IC -> analog front end -> signal conditioning system. Precision FET-input op amps like the OPA2107 combine JFET input stages with laser-trimmed thin-film resistors to achieve very low input bias current without sacrificing DC accuracy, a combination bipolar-input devices cannot match for high-impedance sources. Key features include very low noise at 10 kHz, low offset voltage of 1 mV maximum, low offset drift of 10 µV/°C maximum, and fast settling to 0.01%, while remaining unity-gain stable. The 40 mA per-channel output drive and 80 dB open-loop gain make it suitable for driving ADC inputs and cables directly. The DifET dielectrically isolated process isolates each transistor, reducing junction capacitance and enabling the high slew rate and fast settling that conventional JFET processes cannot deliver. Input bias current of only a few picoamperes allows megohm-level source impedances with minimal DC error, and the dual-channel integration halves board space versus two singles while improving thermal tracking between channels. Typical applications include data acquisition front ends, DAC output buffers, optoelectronic receivers (photodiode transimpedance amplifiers), and high-impedance sensor conditioning such as pH probes and piezoelectric accelerometers. Design consideration: preserve DC accuracy by guarding the high-impedance input node on the PCB and keeping feedback resistor values moderate, since the 10 pA bias current through 1 MΩ already contributes 10 µV of error. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design guidance not found in the manufacturer datasheet alone.

견적 요청 문의하기
OPA2107AU/2K5 - Precision Dual Difet Op Amp 4.5MHz SOIC-8 | TI
OPA2107AU/2K5

OPA2107AU/2K5 - Precision Dual Difet Op Amp 4.5MHz SOIC-8 | TI

The Texas Instruments OPA2107AU/2K5 is a precision dual Difet (dielectrically isolated FET) operational amplifier delivering 4.5 MHz gain bandwidth, 1 mV maximum offset voltage, and 10 pA maximum input bias current in an 8-pin SOIC (D) package. It operates from supplies up to 30 V total (typically +/-15 V) across a -25C to +85C temperature range. An operational amplifier is a high-gain voltage amplifier with differential inputs and a single-ended output that forms the core building block of analog signal chains. Within the amplifier hierarchy, the OPA2107 belongs to the precision JFET-input (Difet) family: precision op amps trade some speed for ultra-low offset, low drift, and low bias current, positioning them above general-purpose amplifiers for measurement-grade signal conditioning but below high-speed amplifiers for video or RF applications. Key features include very low noise at 10 kHz, a maximum offset voltage of 1 mV with maximum drift of 10 uV/C, and a maximum input bias current of 10 pA enabled by the Difet junction-isolation process. The dual-channel integration matches two matched amplifiers on one die, improving thermal tracking between channels. Fast settling to 0.01% and unity-gain stability allow use in active filters and DAC buffers without external compensation. The Difet dielectric isolation technology keeps bias current low across the full temperature range, unlike standard JFET parts whose bias doubles roughly every 10C. This preserves high-impedance sensor accuracy in warm environments. Typical applications from the manufacturer datasheet include data acquisition front ends, DAC output amplifiers, optoelectronic receivers, and high-impedance sensor interfaces such as photodiode and pH probe amplifiers. Design consideration: note this part is in the process of being discontinued per TI, so new designs should qualify a replacement early. The /2K5 suffix denotes tape-and-reel packaging of the standard OPA2107AU die. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet, with availability verified as of 2026-09-13.

견적 요청 문의하기
OPA2107BM - Dual Precision Difet Op Amp, 4.5MHz | TI
OPA2107BM

OPA2107BM - Dual Precision Difet Op Amp, 4.5MHz | TI

The Texas Instruments OPA2107BM is a precision dual Difet operational amplifier offering 4.5 MHz bandwidth, operation up to a 36V total supply (±18V), and a maximum input offset voltage of 1000 uV, housed in an 8-pin TO-99 hermetic metal can package (MBCY8). Originally introduced by Burr-Brown, this part combines precision Difet (dielectrically isolated JFET) performance with the cost and space savings of a dual op amp. An operational amplifier is a high-gain DC-coupled voltage amplifier that, with external feedback networks, forms the fundamental building block of analog signal chains; the op amp sits within the amplifier IC hierarchy of analog integrated circuits and power/analog signal conditioning devices. FET-input amplifiers like the OPA2107 provide extremely low input bias currents compared to bipolar-input predecessors, which is essential when amplifying signals from high-impedance sources. Key features include precision Difet input technology delivering very low input bias current, low input offset voltage drift over temperature, a 4.5 MHz gain-bandwidth suitable for precision audio and instrumentation signals, and the hermetic TO-99 metal can, which offers superior thermal and environmental stability versus plastic packages - a major reason this package remains specified in avionics and military systems. Architecturally, the OPA2107 uses a Difet (dielectrically isolated JFET) process, an advancement over the BIFET process that reduces input bias current and offset drift while preserving slew rate and bandwidth. TI positions it as a drop-in performance upgrade for legacy BIFET-type amplifiers in existing sockets. Typical applications include precision instrumentation front ends, active filter stages in professional audio equipment, integrators and sample-hold circuits, and photodiode or high-impedance sensor preamplifiers where low bias current directly determines measurement accuracy. A key design consideration is that the metal-can package does not dissipate heat as effectively as modern surface-mount packages, so total power dissipation should be checked at high supply voltages. Output drive should also be kept within datasheet limits for stability with capacitive loads. This page synthesizes cross-reference data, drop-in alternative analysis, and practical design guidance not found in the manufacturer datasheet.

견적 요청 문의하기
OPA211ID - 1.1nV/Hz Precision Op Amp 80MHz SOIC-8 | TI
OPA211ID

OPA211ID - 1.1nV/Hz Precision Op Amp 80MHz SOIC-8 | TI

The Texas Instruments OPA211ID is a precision operational amplifier delivering an ultra-low voltage noise density of 1.1 nV/√Hz while consuming only 3.6 mA of quiescent supply current. The single-channel amplifier comes in an 8-pin SOIC package and is fully specified from -40C to +125C. It is unity-gain stable with a rail-to-rail output stage. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, a fundamental building block of analog signal chains. Precision op amps such as the OPA211 sit within the amplifier hierarchy: amplifier > operational amplifier > precision op amp, characterized by low offset, low noise, and high open-loop gain. They are essential in instrumentation, medical equipment, and test systems where signal accuracy is critical. Key features include the 1.1 nV/√Hz input-referred noise density - among the lowest available for a precision op amp - plus a gain-bandwidth product of 80 MHz and 20 V/µs slew rate for high-speed signals. The rail-to-rail output maximizes dynamic range in low-supply designs. DC accuracy is strong with 50 µV typical offset voltage and 60 nA input bias current, and total harmonic distortion plus noise is a very low 0.000015%. Technically, the OPA211 uses a bipolar input stage with laser trimming to minimize offset and drift. The class-AB output stage provides low distortion and solid capacitive-drive capability. Single (OPA211) and dual (OPA2211) versions exist, with shutdown options on single-channel family members, packaged in SON-8 (3x3 mm), VSSOP-8, and SOIC-8. Typical applications include low-noise audio preamplifiers, precision instrumentation front ends, active filters, and data-acquisition stages driving high-resolution ADCs such as the ADS1262. The 80 MHz bandwidth also suits photodiode transimpedance amplifiers and RF/IF signal chains. Design tip: place 0.1 µF ceramic decoupling capacitors close to the supply pins, and respect the input common-mode range to avoid phase reversal. For a second channel, the OPA2211 shares the same performance in one package. Prices as of 2026-08-30.

견적 요청 문의하기
OPA2132U - Dual 8 MHz 5 pA FET Op Amp | Texas Instruments
OPA2132U

OPA2132U - Dual 8 MHz 5 pA FET Op Amp | Texas Instruments

Texas Instruments OPA2132U is a dual, FET-input operational amplifier with 8 MHz gain-bandwidth product, maximum input bias current of 5 pA, and an 8-pin SOIC package. It combines a maximum slew rate of 20 V/µs with low distortion of 0.00008%, making it suitable for precision audio, communications, data-acquisition, and general-purpose signal-conditioning systems. A FET-input operational amplifier is a voltage-amplifier IC whose input stage uses field-effect transistors rather than bipolar transistors. This architecture places the amplifier within the operational-amplifier, analog-amplifier, and semiconductor hierarchies while providing very low input bias current, high input impedance, and effective operation with high-impedance signal sources. The OPA2132 series is specifically positioned for audio applications where low distortion, wide bandwidth, and fast settling are important. The principal features of the OPA2132U include a 5 pA maximum input bias current, 8 MHz bandwidth, 20 V/µs slew rate, and 130 dB open-loop gain with a 600 Ω load. Its low distortion helps preserve small-signal detail in audio paths, while its high slew rate allows large-amplitude signals to change rapidly without excessive distortion. The device also supports a wide ±18 V supply range, giving designers flexibility in dual-supply audio and instrumentation systems. Technically, the OPA2132U belongs to the OPAx132 family of high-speed, high-performance FET-input operational amplifiers. The single, dual, and quad family members share key specifications, which simplifies design planning when channel count changes. The combination of high bandwidth and high slew rate improves signal fidelity when the amplifier must drive downstream stages, maintain accurate waveforms, or amplify signals from high-impedance transducers. The dual configuration provides two amplifiers in one package while conserving board area. Typical applications include high-fidelity audio preamplification, active filters, low-level sensor conditioning, communications equipment, and instrumentation inputs. In an audio preamplifier, the low distortion supports faithful reproduction of small signals, while the fast slew rate handles rapidly changing waveform content. In sensor or data-acquisition systems, the 5 pA input bias current limits loading on high-impedance sources, and the 130 dB open-loop gain provides high precision in feedback configurations. Circuit design should preserve the amplifier's low-noise and high-impedance behavior by keeping input traces short, providing stable feedback compensation, and avoiding excessive capacitive loading on either input. Decoupling capacitors should be placed close to the supply pins, while the unused amplifier in the dual package should be configured according to the manufacturer recommendations rather than left floating. This product page combines the manufacturer specifications, package information, verified pricing structure, drop-in replacement assessment, comparison data, and practical circuit guidance. It highlights where the OPA2132U's 8 MHz bandwidth, 5 pA bias current, 20 V/µs slew rate, and low distortion make it a practical choice for precision analog signal paths.

견적 요청 문의하기
OPA2134UA/2K5 - Dual Audio Op-Amp 0.00008% THD | TI
OPA2134UA/2K5

OPA2134UA/2K5 - Dual Audio Op-Amp 0.00008% THD | TI

The Texas Instruments OPA2134UA/2K5 is a dual SoundPlus high-performance audio operational amplifier in an 8-pin SOIC package, supplied in 2,500-unit tape-and-reel format. It combines ultra-low distortion (0.00008% THD), low noise (8 nV/rtHz), true FET input (5 pA bias current), 20 V/us slew rate, and 8 MHz gain-bandwidth, operating from +/-2.5 V to +/-18 V supplies. An audio operational amplifier is a precision linear amplifier optimized to pass audio-band signals with minimal added harmonic distortion, noise, and phase error. It sits in the analog signal chain between transducers, DACs, and loudspeakers, and is a specialized subclass of the general op amp: an audio op amp is a linear amplifier within the analog signal processing chain of consumer, professional, and automotive audio electronics. Key features include the 0.00008% total harmonic distortion figure that keeps the device transparent in the audible signal path, 8 nV/rtHz voltage noise for low hiss in high-gain stages, and 5 pA FET input bias current that prevents loading of high-impedance sources such as guitar pickups and passive EQ networks. The 8 MHz bandwidth and 20 V/us slew rate preserve full-power performance across the entire 20 Hz to 20 kHz audio band, and the wide +/-18 V supply range matches standard professional audio rails. Architecturally, the OPA2134 uses a true FET input stage with a high open-loop gain of 600 V/mV (per TI datasheet), delivering excellent DC precision alongside audio-grade AC performance. The dual-channel SOIC-8 configuration enables compact stereo designs without performance compromise, and the single (OPA134) and quad (OPA4134) family members share identical core specifications for BOM flexibility. Typical applications include audio DAC output buffering (I/V conversion), line drivers, active crossovers, microphone preamplifiers, and audio test instrumentation, where the OPA2134UA/2K5 is often the limiting factor in signal purity. Design tip: bypass each supply pin with a 0.1 uF ceramic capacitor placed close to the package, and maintain adequate input/output headroom since this is not a rail-to-rail op amp. Prices as of 2026-08-30.

견적 요청 문의하기
OPA2134UA/2K5 - Dual Audio Op-Amp 0.00008% THD | TI
OPA2134UA/2K5

OPA2134UA/2K5 - Dual Audio Op-Amp 0.00008% THD | TI

The Texas Instruments OPA2134UA/2K5 is a dual SoundPlus high-performance audio operational amplifier delivering 0.00008% total harmonic distortion, 8 nV per root-hertz input voltage noise, and a 20 V/us slew rate in an 8-pin SOIC package, supplied in 2,500-unit tape-and-reel format. An audio operational amplifier is a precision linear amplifier optimized to pass audio-band signals with minimal added harmonic distortion, noise, and phase error. It sits in the analog signal chain between transducers, DACs, and loudspeakers, and is a specialized subclass of the general op amp: an audio op amp is a linear amplifier within the analog signal processing chain of consumer, professional, and automotive audio electronics. Key features include the 0.00008% total harmonic distortion figure that keeps the device transparent in the audible signal path, 8 nV/rtHz voltage noise for low hiss in high-gain stages, and 5 pA FET input bias current that prevents loading of high-impedance sources such as guitar pickups and passive EQ networks. The 8 MHz gain-bandwidth product and 20 V/us slew rate preserve full-power performance across the entire 20 Hz to 20 kHz audio band, and the wide +/-2.5 V to +/-18 V supply range matches standard professional audio rails. Architecturally, the OPA2134 uses a true FET input stage with a high open-loop gain of 600 V/mV per the TI datasheet, delivering excellent DC precision alongside audio-grade AC performance. The dual-channel SOIC-8 configuration enables compact stereo designs without performance compromise, and the single (OPA134) and quad (OPA4134) family members share identical core specifications for BOM flexibility. Typical applications include audio DAC output buffering (I/V conversion), line drivers, active crossovers, and microphone preamplifiers, where the OPA2134UA/2K5 is often the limiting factor in signal purity. Design tip: bypass each supply pin with a 0.1 uF ceramic capacitor placed close to the package, and maintain adequate input/output headroom since this is not a rail-to-rail op amp. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

USD $0.92 문의하기
OPA2137U - Dual 36V 1MHz J-FET Op Amp | Texas Instruments
OPA2137U

OPA2137U - Dual 36V 1MHz J-FET Op Amp | Texas Instruments

The Texas Instruments OPA2137U is a dual J-FET-input operational amplifier with 1 MHz gain-bandwidth product, 3.5 V/µs slew rate, and a 36 V maximum total supply rating, housed in an 8-pin SOIC package. Both amplifiers provide low input bias current of ±10 pA, a quiescent current of 120 µA per channel, and an open-loop gain of 145 dB. A J-FET-input operational amplifier is a voltage-amplifier device whose field-effect transistor input stage provides very low input bias current. Within the broader semiconductor hierarchy, the OPA2137U belongs to the operational-amplifier family of analog ICs and supports low-impedance sensing, precision feedback networks, signal conditioning, and general-purpose analog signal paths. Unlike bipolar-input amplifiers, its J-FET inputs place minimal DC current on high-impedance sources. The OPA2137 series is designed for low-cost and miniature applications. Important characteristics include a ±10 pA input bias current, 120 µA per channel of quiescent current, and 145 dB open-loop gain. The dual configuration provides two amplifiers in one package while maintaining identical performance between channels, making it convenient for differential, active-filter, instrumentation, and buffer circuits. The device operates across a total supply range of ±2.25 V to ±18 V, equivalent to 4.5 V to 36 V across the supply terminals. Its 1 MHz gain-bandwidth product and 3.5 V/µs slew rate provide useful bandwidth for audio-frequency and low-frequency instrumentation applications. The input common-mode range includes the positive supply, allowing the amplifier to operate from a single supply when appropriately configured. Typical applications include low-level signal conditioning, buffered sensor outputs, audio preamplification, active filters, sample-and-hold circuitry, and precision analog measurement systems. The low bias current is particularly valuable when driving high-impedance detectors, transducers, or measurement nodes, while the low per-channel quiescent current supports compact and power-sensitive instruments. Designers should verify the complete input and output common-mode ranges, input bias-current behavior, output swing, and stability requirements against the manufacturer datasheet for the selected supply and load conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive input nodes should use short traces, guarded routing, and a clean ground reference to minimize leakage and interference. This page combines manufacturer specifications, package and lifecycle information, drop-in replacement candidates, application guidance, and engineering design notes. It is intended to help designers compare the OPA2137U with same-footprint alternatives while selecting a part that matches the required bandwidth, supply voltage, input impedance, and environmental conditions.

견적 요청 문의하기
OPA2170AIDCUR - 36V Dual Op Amp, Rail-to-Rail Output, VSSOP-8 | Texas Instruments
OPA2170AIDCUR

OPA2170AIDCUR - 36V Dual Op Amp, Rail-to-Rail Output, VSSOP-8 | Texas Instruments

The Texas Instruments OPA2170AIDCUR is a dual-channel, 36 V, single-supply, low-power operational amplifier in a VSSOP-8 (DCU) micro-package, featuring rail-to-rail output swing, 1.2 MHz gain-bandwidth product, and 0.4 V/us slew rate for general-purpose analog signal conditioning. Each channel delivers a low offset voltage and low offset drift while consuming only 110 uA per channel of quiescent current, making this op amp suitable for battery-powered and always-on sensor interfaces. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output, forming the fundamental building block of analog signal chains. It belongs to the broader category of linear integrated circuits within power management and analog signal conditioning, and is used for amplification, filtering, level shifting, buffering, and comparator functions. The OPA2170AIDCUR is part of TI's OPAx170 value-line family, alongside the single-channel OPA170 and quad-channel OPA4170, all sharing identical specifications to simplify design reuse across channel densities. The OPAx170 architecture operates from a single 2.7 V to 36 V supply (or dual ±1.35 V to ±18 V), eliminating the need for negative rails in single-supply systems. Key differentiating features include 19 nV/√Hz input voltage noise density, RFI-filtered inputs to reject out-of-band RF interference, and an input common-mode range that extends to the negative supply rail, which is critical for ground-referenced single-supply sensing. The device also includes internal ESD protection on the inputs and outputs, simplifying board-level robustness. Combined, these features enable precision measurement in noisy industrial environments. Typical applications include transducer signal conditioning for bridge sensors, temperature sensor interfaces (thermocouples, RTDs, thermistors), active filtering for audio and instrumentation, low-side current sensing, and portable medical or test equipment. The 36 V supply tolerance also supports 24 V industrial bus interfaces and automotive load-dump-protected rails. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to the V+ pin, and use a low-ESR ceramic at the supply. For unity-gain buffer or low-gain stages, a 10 nF to 100 nF compensation capacitor between V+ and the output node may improve capacitive load drive. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page.

견적 요청 문의하기
OPA2170AIDGK - 36V Dual Op Amp, RRO, 1.2MHz | Texas Instruments
OPA2170AIDGK

OPA2170AIDGK - 36V Dual Op Amp, RRO, 1.2MHz | Texas Instruments

The Texas Instruments OPA2170AIDGK is a dual-channel, 36V, single-supply, low-power operational amplifier (op amp) housed in an 8-pin MSOP/VSSOP package (DGK). It delivers a 1.2 MHz gain-bandwidth product, a 0.4 V/us slew rate, and a low 19 nV/sqrt(Hz) input-referred voltage noise density while drawing only 110 uA of quiescent current per channel. The device operates from 2.7V to 36V single supply (or +/-1.35V to +/-18V dual supply), making it well-suited to industrial 24V rails as well as 3.3V / 5V low-voltage analog signal chains. An operational amplifier (op amp) is a high-gain differential voltage amplifier that uses external feedback components to set closed-loop gain, bandwidth, and transfer function. Op amps are fundamental building blocks in analog signal conditioning: they amplify, buffer, filter, sum, and convert signals. Within the broader hierarchy, a dual low-power op amp like the OPA2170 sits below the "linear IC" family, adjacent to instrumentation amplifiers, comparators, and programmable gain amplifiers. The "value line" label from TI indicates it is positioned for cost-sensitive, high-volume designs without sacrificing key specs. Key features of the OPA2170 include 0.0035 uA input bias current (CMOS input stage), 120 dB CMRR, rail-to-rail output (RRO), an input common-mode range that includes the negative rail, and EMI/RFI filtered inputs to improve immunity in harsh electrical environments. The unity-gain-stable design requires no external compensation and supports capacitive loads up to 1 nF. Architecturally, the OPA2170 uses a CMOS input stage for high input impedance and low bias current, combined with a class AB output stage that achieves rail-to-rail swing on a single supply. This combination makes the part equally suitable for low-voltage sensor signal chains (where input bias current matters) and higher-voltage industrial loops (where supply tolerance matters). Typical applications include transducer signal conditioning, 4-20 mA loop drivers, low-side current sensing, active filters, audio signal buffering, general-purpose amplification in PLC analog input modules, and battery-powered instrumentation that needs wide supply tolerance. When designing in the OPA2170AIDGK, be mindful that although the inputs include the negative rail, the inputs do NOT include the positive rail - common-mode voltage must remain at least a few hundred mV below V+ for linear operation. Use the dual-channel part when two related signals (e.g., a differential sensor) need matched amplifier paths; switch to the quad-channel OPA4170 only when the PCB area savings of one IC outweigh the loss of channel-level routing flexibility. This page synthesizes distributor pricing, verified cross-reference alternatives in the same VSSOP-8 footprint, and practical design considerations not found in the manufacturer datasheet alone.

견적 요청 문의하기
OPA2171AIDR - Dual 36V 3MHz Low-Power Op Amp | Texas Instruments
OPA2171AIDR

OPA2171AIDR - Dual 36V 3MHz Low-Power Op Amp | Texas Instruments

The Texas Instruments OPA2171AIDR is a dual-channel, 36V, 3MHz, low-power operational amplifier in an 8-pin SOIC package. The OPA2171AIDR is part of the OPAx171 family (single/dual/quad) and is designed for single-supply operation from 2.7V (±1.35V) to 36V (±18V). It features rail-to-rail output (RRO), low offset voltage, low drift, and low quiescent current, making it well-suited for cost-sensitive general-purpose analog signal conditioning. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. It is the fundamental building block of analog signal chains, used for amplification, filtering, comparison, buffering, and mathematical operations. The OPA2171 belongs to the lineage of low-power, general-purpose amplifiers, sitting between precision op amps (high accuracy, high power) and high-speed op amps (wide bandwidth, higher noise), optimized for applications requiring moderate bandwidth and low current draw. Key features of the OPA2171AIDR include 3MHz gain-bandwidth product, 1.5V/µs slew rate, low quiescent current, rail-to-rail output swing, and 36V maximum supply voltage. The 3MHz gain-bandwidth product enables stable operation in active filter circuits, sensor signal conditioning, and transducer amplification. The wide supply range supports industrial 24V bus systems, automotive 12V rails (post-protection), and battery-powered portable equipment operating down to 2.7V. The OPA2171 uses a CMOS input stage for low input bias current, paired with a rail-to-rail output stage that maximizes dynamic range on low-voltage supplies. Internal EMI/RFI filtering on the inputs improves robustness in harsh electrical environments. The dual op-amp configuration in the SOIC-8 package provides two independent amplifiers in a small footprint, enabling compact multi-channel designs. Typical applications include transducer amplification, sensor signal conditioning, industrial process control, battery-powered instrumentation, active filters, and voltage reference buffers. The wide input range allows direct interfacing with 24V industrial sensors, while the rail-to-rail output maximizes dynamic range on 3.3V or 5V ADC rails. When designing with this device, pay attention to input common-mode range, especially near the negative rail where CMOS input stages exhibit degraded behavior. Decouple supply pins with 0.1µF ceramic capacitors placed close to the IC. This page synthesizes distributor pricing, drop-in alternatives (including same-brand OPA2171AID and OPA4171 variants), and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
OPA2172 - 36V 10MHz Dual Rail-to-Rail Op Amp | Texas Instruments
OPA2172

OPA2172 - 36V 10MHz Dual Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments OPA2172 is a dual, 36-V, 10-MHz, rail-to-rail output (RRO) operational amplifier in an 8-pin SOIC (D) package. It operates on supplies from +4.5 V (±2.25 V) to +36 V (±18 V), combining wide dynamic range with low power consumption of 1.6 mA per amplifier. An operational amplifier (op amp) is a high-gain differential voltage amplifier used as the building block of analog signal chains - a subcategory of amplifier ICs within the broader power-management and signal-conditioning hierarchy. The OPA2172 belongs to TI's OPAx172 family (OPA172 single, OPA2172 dual, OPA4172 quad), which is engineered for high-voltage, single-supply designs where the output must swing close to the rails. Key features include a gain-bandwidth product of 10 MHz, low input offset voltage of ±0.2 mV, and ultra-low offset drift of ±0.3 uV/degC, ensuring accuracy across the industrial temperature range. Input bias current is a low ±8 pA thanks to the JFET-input front end, and broadband noise is 7 nV/rtHz, making the part suitable for precision, low-noise signal conditioning. High slew rate supports fast settling in active filters and ADC drivers. Architecturally, the OPA2172 uses a precision input stage with rail-to-rail output stage that maintains low distortion even when driving loads near the supply rails. The 36-V tolerance provides headroom against industrial 24-V bus transients, and operation down to +4.5 V supports 5-V single-supply systems. Typical applications include 24-V industrial instrumentation front ends, active filter and data-acquisition signal conditioning ahead of ADCs such as the ADS131M08, sensor buffering, and output amplification in audio and synth-DIY circuits where it replaces noisier TL072-class devices. Design tip: keep total supply below 36 V, and for maximum output swing at low loads, ensure load impedance keeps output current within datasheet limits; bypass both supply pins with 100 nF ceramics placed close to the device.

견적 요청 문의하기
OPA2172 - Dual 36V 10MHz Low-Noise Op Amp | Texas Instruments
OPA2172ID

OPA2172 - Dual 36V 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments OPA2172ID is a dual, 36-V, 10-MHz, low-power rail-to-rail output operational amplifier in an 8-SOIC package, part of the OPAx172 family that also includes the single OPA172 and quad OPA4172. It operates on supplies from +4.5 V to +36 V (or ±2.25 V to ±18 V), making it versatile for single-supply and dual-supply industrial systems. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, and is a fundamental building block of analog signal conditioning, filtering, and amplification. The OPA2172 sits in the hierarchy of amplifiers -> operational amplifiers -> precision, rail-to-rail output amplifiers, balancing bandwidth, noise, and power in one general-purpose part. Key specifications include ±0.2 mV offset voltage, ±0.3 uV/C offset drift, 10 MHz gain-bandwidth product, ±8 pA input bias current, 1.6 mA quiescent current per amplifier, and 7 nV/√Hz broadband noise. The rail-to-rail output stage maximizes dynamic range in low-voltage designs, while the wide supply range supports industrial 24 V buses directly. The CMOS input stage provides high input impedance and picoampere bias currents suitable for high-impedance sensors and photodiode circuits. The output stage swings to within millivolts of the rails at light load and is stable with substantial capacitive loads, simplifying buffer designs. Low quiescent current permits use in battery-powered and thermally constrained equipment. Typical applications include motor-control current sensing, solar inverters, power-supply feedback loops, active filters, and audio signal chains, where low noise and high slew rate preserve signal fidelity. The dual channel saves board space versus two singles. Design tip: decouple supply pins with 0.1 uF ceramics close to the device, keep feedback resistors low-valued for best noise, and verify output swing headroom under heavy load.

견적 요청 문의하기
OPA2192IDGK - 36V Precision RRIO Op Amp Dual | TI
OPA2192IDGK

OPA2192IDGK - 36V Precision RRIO Op Amp Dual | TI

The Texas Instruments OPA2192IDGK is a dual-channel, 36-V precision operational amplifier with rail-to-rail input/output (RRIO), low offset voltage, and low input bias current, implemented in TI's e-trim chopper-stabilized architecture and packaged in an 8-pin MSOP (PowerPAD). It carries an automotive temperature grade and supports up to +/-18 V or 36 V single-supply operation from a 4.5 V to 36 V rail. Background: An operational amplifier (op amp) is a high-gain DC-coupled analog building block that uses external feedback to set gain, filter response, and signal conditioning behavior. The OPA2192IDGK belongs to the precision op-amp family, characterized by microvolt-level input offset voltage, picoampere-range input bias current, and low drift over temperature - a category that sits above general-purpose op amps and below zero-drift chopper amplifiers in the precision signal-chain hierarchy. Rail-to-rail input/output op amps accept and produce signals that swing to both supply rails, which maximizes dynamic range in low-voltage single-supply designs and is critical for driving successive-approximation ADCs without headroom loss. Key specifications include 5 pA typical input bias current, 25 uV maximum input offset voltage, 0.5 uV/degC typical offset drift, 10 MHz unity-gain bandwidth, and 20 V/us slew rate. The e-trim architecture provides 5 uV/degC offset drift without the chopping sidebands or large inrush currents of classic chopper amplifiers. EMI-hardened inputs reject RF interference from adjacent switching converters and motor drivers in industrial environments. The MSOP-8 package with PowerPAD delivers a thermal resistance of approximately 50 C/W, enabling dual-channel operation at full bandwidth without external heatsinking. Typical applications include precision weigh scales, sensor signal conditioning for thermocouples and strain gauges, battery management current sensing, and industrial analog input modules. Designers select the OPA2192IDGK for systems requiring sub-100 uV total DC accuracy across the full -40C to +125C automotive temperature range and tight PCB footprints where two precision channels must fit into a 3 mm x 3 mm outline. Designers should note the OPA2192IDGK is pin-compatible with the OPA2191 (lower precision), OPA2188 (zero-drift), and OPA2227 (lower precision), enabling drop-in upgrades. For optimal performance, bypass supplies with 0.1 uF ceramic capacitors placed within 5 mm of the V+ and V- pins. This page consolidates real-time distributor pricing, drop-in alternatives, and design notes beyond the manufacturer datasheet to accelerate part selection.

견적 요청 문의하기
OPA2192IDGKR - 36V Precision RRIO Dual Op Amp | Texas Instruments
OPA2192IDGKR

OPA2192IDGKR - 36V Precision RRIO Dual Op Amp | Texas Instruments

The Texas Instruments OPA2192IDGKR is a 36-V, precision, rail-to-rail input/output (RRIO), low-offset-voltage, low-input-bias-current operational amplifier with e-trim, delivered in an 8-pin VSSOP (DGK) package. Key headline parameters include 10-MHz unity-gain bandwidth, 20-V/µs slew rate, ±5-µV typical offset voltage, ±0.2-µV/°C typical offset drift, and 4.5-V to 36-V single-supply operation (or ±2.25-V to ±18-V dual). The e-trim calibration architecture trims input offset and offset drift at the wafer level, eliminating the need for external nulling components. An operational amplifier (op amp) is a high-gain DC-coupled analog circuit block that amplifies differential input voltages. The OPA2192 belongs to the precision amplifier sub-class, where DC accuracy (low offset, low drift) and rail-to-rail signal swing matter more than raw speed. It sits in the broader hierarchy of linear ICs -> amplifiers -> operational amplifiers -> precision RRIO op amps -> semiconductor, and competes with parts such as the ADA4522 and OPA2188. Its main role in a system is to condition small analog signals (sensor bridges, shunt currents, thermocouples) with minimal added error and to drive ADC reference or output stages up to the supply rails. Distinctive features include differential input-voltage range to the supply rail, high-output current drive with no phase reversal, low-input-bias current with e-trim, and integrated EMI/RFI rejection at 1 GHz. The OPA2192 also offers independent short-circuit protection on the outputs and a wide 4.5-V to 36-V supply headroom that lets a single device serve both 5-V analog rails and 24-V industrial transducers. Architecturally, the OPA2192 uses a bipolar input stage with chopper-free e-trim post-package calibration, preserving low noise while achieving 10-MHz GBW at 20 V/µs. The RRIO output stage swings within millivolts of either rail at moderate loads, eliminating headroom loss in low-voltage ADC interfaces and giving designers full dynamic range on 5-V or 12-V rails. Typical applications include precision analog input modules, 4-20 mA loop transmitters, multi-channel data acquisition front ends, test and measurement instruments, and active filtering in audio paths. Designers favor it where both 5-V digital-rail operation and 24-V industrial transducers must share one BOM line. When using the OPA2192, observe the maximum differential input-voltage limit and add an input-series resistor for true over-voltage protection; a 2-kΩ resistor on each input typically prevents fault-current damage during 36-V transients. This page also synthesizes distributor pricing, drop-in alternates, and practical design notes that the TI datasheet alone does not surface.

견적 요청 문의하기
OPA2192IDGKT - 36V Precision RRIO Op Amp, 10MHz, Dual | Texas Instruments
OPA2192IDGKT

OPA2192IDGKT - 36V Precision RRIO Op Amp, 10MHz, Dual | Texas Instruments

The Texas Instruments OPA2192IDGKT is a dual-channel, 36-V, e-trim precision operational amplifier that delivers rail-to-rail input and output (RRIO) swing, 10 MHz unity-gain bandwidth, and 20 V/µs slew rate in an 8-pin VSSOP (DGK) package. According to the manufacturer datasheet, the OPA2192 family offers typical input offset voltage of ±5 µV, offset drift of ±0.2 µV/°C, and a 1 mA per-channel quiescent supply current while supporting output current up to 65 mA per channel for direct drive of low-impedance loads. A precision operational amplifier (op amp) is a high-gain DC-coupled analog building block used to amplify small differential signals in instrumentation, signal conditioning, and active-filter chains. The OPA2192 belongs to the e-trim chopper-stabilized family that achieves CMOS-class input bias current with bipolar-class DC accuracy, positioning it above general-purpose op amps in the precision amplifier hierarchy: precision op amp -> operational amplifier -> analog IC -> signal chain -> semiconductor. Key features include differential input range that extends to both supply rails, integrated EMI/RFI rejection input filtering, and 6 V to 36 V single-supply operation (or ±3 V to ±18 V dual-supply). The e-trim process eliminates the traditional chopper chopping artifacts, making the part suitable for DC-coupled precision paths where chopper noise would otherwise be unacceptable. Architecture-wise, the OPA2192 combines a CMOS input differential pair with TI's e-trim calibration to correct residual input-referred offset at the wafer level. This achieves laser-trim performance without active chopping, providing clean DC behavior at low frequencies while still supporting the 10 MHz GBW required by audio and wide-bandwidth transducer signal conditioning. Typical applications include industrial process-control analog front ends, precision analog-input modules for PLCs, multi-channel data-acquisition (DAQ) signal conditioning, precision active filters, and transducer excitation/readout such as bridge amplifiers and RTD conditioners. The wide supply range allows direct interface to ±15 V industrial rails as well as 24 V loop-powered systems. When designing with this device, ensure that the input common-mode voltage stays within the rail-to-rail range (which includes both rails). Decouple the supply pins with a 100 nF ceramic capacitor placed within 5 mm of the device, and consider a 10 µF bulk capacitor for high-output-current transients. The exposed thermal pad (if present on the package variant) must be soldered to a copper pour for rated thermal performance. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes that go beyond the manufacturer datasheet, helping engineers shorten selection time and avoid common layout pitfalls.

견적 요청 문의하기
OPA2192IDR - 36V Precision RRIO Dual Op Amp e-Trim | TI
OPA2192IDR

OPA2192IDR - 36V Precision RRIO Dual Op Amp e-Trim | TI

The Texas Instruments OPA2192IDR is a dual-channel, 36V precision operational amplifier with rail-to-rail input and output (RRIO), delivered in an 8-pin SOIC (D) package rated from -40C to +125C. It combines low offset voltage, low input bias current, and TI e-trim calibration technology for outstanding DC precision in a cost-effective general-purpose amplifier. A precision operational amplifier is a type of analog amplifier IC designed to amplify small differential signals with minimal error, positioned within the hierarchy of op amps > precision amplifiers > analog front-end ICs > linear ICs. Unlike general-purpose op amps, precision amplifiers minimize input offset voltage, bias current, and drift so sensor and measurement signal chains remain accurate without external trimming. Key features include operation from 4.5V to 36V single supply (or +/-2.25V to +/-18V dual supply), a 10MHz gain-bandwidth product, and a 20V/us slew rate - a rare combination of DC precision and AC performance. The e-trim architecture achieves very low offset voltage without system-level trimming, while rail-to-rail inputs allow the common-mode range to extend to both supplies and rail-to-rail output maximizes dynamic range on low-voltage rails. Architecturally, the OPA2192 uses an input stage that seamlessly transitions between two differential pairs to maintain rail-to-rail common-mode operation, with e-trim calibration performed at wafer test to null residual offset. The low input bias current suits high-impedance sources, and low total harmonic distortion supports precision AC signal chains. Typical applications include industrial data acquisition front ends, transimpedance and sensor signal conditioning, precision active filters, and single-supply battery-powered instrumentation. The wide 36V supply rating also allows direct connection to industrial 24V rails with simple headroom management. Design tip: reference the input common-mode near mid-supply to minimize crossover distortion inherent in dual-pair input stages, and verify AC behavior near the rails in high-precision designs.

견적 요청 문의하기
OPA2206ADGKR - ±40V OVP Dual Precision Op Amp | Texas Instruments
OPA2206ADGKR

OPA2206ADGKR - ±40V OVP Dual Precision Op Amp | Texas Instruments

The Texas Instruments OPA2206ADGKR is a dual-channel, input-overvoltage-protected (OVP) precision operational amplifier housed in an 8-pin VSSOP (DGK) package, with integrated input protection up to ±40 V beyond the supplies, an input offset voltage of 4 µV (typical) / 25 µV (maximum), an input offset voltage drift of ±0.08 µV/°C (typical), and an input bias current of ±5 pA (typical) via super-beta input transistors. An operational amplifier (op amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, typically, a single-ended output. Precision op amps form a distinct sub-category characterized by very low offset voltage, low offset drift, low bias current, and low noise, sitting hierarchically under amplifier ICs (integrated circuits) and analog signal-chain components. The OPA2206 is the dual-channel member of TI's OPAx206 family and represents the next-generation evolution of the long-standing OPAx277 series, retaining the OPAx277's low-noise, low-drift e-trim™ precision architecture while adding integrated ±40 V input OVP, eliminating the need for external input clamping in many industrial designs. Key features include 4 µV (typ) / 25 µV (max) offset voltage achieved via TI's proprietary e-trim™ trimming technology, ±0.08 µV/°C (typ) offset drift, ±5 pA (typ) input bias current enabled by super-beta input transistors, integrated ±40 V input OVP that survives ESD and transients beyond the rails, and a wide supply range of 4.5 V to 36 V (single supply) or ±2.25 V to ±18 V (dual supply). The device is specified over the −40 °C to +125 °C industrial temperature range. Architecturally, the OPA2206 uses a bipolar e-trim™ process with super-beta input stages, which decouple bias current from base current, dramatically reducing input bias current while preserving the low-noise and low-drift characteristics of a precision bipolar op amp. The e-trim™ trim step digitally calibrates each die's offset to <25 µV at room temperature and minimizes drift across temperature. Typical applications include industrial process-control analog input modules, precision sensor signal conditioning (load cells, strain gauges, thermocouple front-ends), test and measurement equipment, battery monitoring systems, and any high-voltage-tolerant precision front-end where input transients or wiring faults could otherwise destroy a conventional op amp. The wide supply and ±40 V OVP make it a strong fit for 24-V industrial-bus sensor interfaces. When designing with this device, place the input series resistors as close to the OPA2206 inputs as possible to maximize the effectiveness of the integrated OVP clamp structure and to limit fault current through the ESD diodes. The OPA2206 does not include rail-to-rail output; output swing is typically within ~1 V of each rail at 10 kΩ load. This page synthesizes distributor pricing, drop-in alternatives in the VSSOP-8 footprint, and practical design notes that are not found in the manufacturer datasheet alone.

견적 요청 문의하기
OPA2227P - Dual Precision Low-Noise Op Amp | Texas Instruments
OPA2227P

OPA2227P - Dual Precision Low-Noise Op Amp | Texas Instruments

Texas Instruments OPA2227P is a dual high-precision, low-noise operational amplifier with two amplifier circuits in an 8-pin PDIP package. Its stated characteristics include 3 nV/√Hz noise, 10 V/µs slew rate, 5 µs settling time, and 138 dB common-mode rejection, making it suitable for precision DC and AC signal conditioning. The device is specified for operation from -40°C to +85°C. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Its place in the signal-chain hierarchy is operational amplifier → analog IC → semiconductor, while precision operation refers to maintaining accurate DC gain and offset behavior as well as low-distortion AC performance. The dual configuration provides two amplifiers in one package, reducing board area compared with two separate single-channel devices. The OPA2227P combines low noise with wide bandwidth and high precision. The 3 nV/√Hz noise figure makes it relevant to sensor signals, instrumentation amplifiers, audio paths, and other applications in which input-referred noise limits usable resolution. Its 138 dB CMRR helps reject common-mode interference, while the 10 V/µs slew rate and 5 µs settling characteristics support faster closed-loop signal transitions than precision amplifiers with narrower bandwidth. OPA2227 and OPA228 devices are identified by Texas Instruments as pin-for-pin replacements for industry-standard OP27 and OP37 devices. The OPA2227P therefore supports legacy precision-amplifier designs while offering a dual-channel implementation. Its internal characteristics are suited to both DC measurement and AC-coupled applications where low noise, stable gain, and common-mode rejection are important. Typical uses include precision measurement front ends, low-level sensor amplifiers, buffered analog outputs, laboratory instrumentation, audio equipment, and active analog filters. The PDIP-8 package is suited to through-hole prototyping and designs where a mechanically robust package and readily visible connections are useful. Board-level compatibility still requires verification of supply voltage, input common-mode range, output swing, and stability configuration. Design with the manufacturer datasheet as the controlling reference for maximum supply voltage, input bias current, offset voltage, open-loop gain, output-current capability, and recommended compensation. Place a short, low-impedance return from the power-supply pins to the ground plane, and provide adequate bypass capacitance close to the device. Avoid placing long copper traces beside sensitive input nets, and confirm that the selected gain and feedback network remain stable at the intended frequency. This product record combines manufacturer ordering information, device-family positioning, precision and noise characteristics, practical application guidance, and drop-in replacement analysis. It helps engineers distinguish the PDIP OPA2227P from related single, dual, quad, and alternate-family variants before committing a PCB footprint or production release.

견적 요청 문의하기