OPA2172 - Dual 36V 10MHz Low-Noise Op Amp | Texas Instruments
부품 번호: OPA2172ID ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1.85 | $1.85 |
| 10 | $1.66 | $16.60 |
| 100 | $1.32 | $132.00 |
| 500 | $1.12 | $560.00 |
| 1,000 | $0.94 | $940.00 |
OPA2172ID 개요
An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, and is a fundamental building block of analog signal conditioning, filtering, and amplification. The OPA2172 sits in the hierarchy of amplifiers -> operational amplifiers -> precision, rail-to-rail output amplifiers, balancing bandwidth, noise, and power in one general-purpose part.
Key specifications include ±0.2 mV offset voltage, ±0.3 uV/C offset drift, 10 MHz gain-bandwidth product, ±8 pA input bias current, 1.6 mA quiescent current per amplifier, and 7 nV/√Hz broadband noise. The rail-to-rail output stage maximizes dynamic range in low-voltage designs, while the wide supply range supports industrial 24 V buses directly.
The CMOS input stage provides high input impedance and picoampere bias currents suitable for high-impedance sensors and photodiode circuits. The output stage swings to within millivolts of the rails at light load and is stable with substantial capacitive loads, simplifying buffer designs. Low quiescent current permits use in battery-powered and thermally constrained equipment.
Typical applications include motor-control current sensing, solar inverters, power-supply feedback loops, active filters, and audio signal chains, where low noise and high slew rate preserve signal fidelity. The dual channel saves board space versus two singles.
Design tip: decouple supply pins with 0.1 uF ceramics close to the device, keep feedback resistors low-valued for best noise, and verify output swing headroom under heavy load.
드롭인 대체품: OPA2172ID — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA2172ID (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Gain Bandwidth Product, Package, Supply Voltage Range.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
OPA2172AID
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
OPA2172QDDFRQ1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA2171AID
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
OPA2170AID
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
OPA1688ID
⚡ 동일 패키지✓ 재고 있음
$0.82 / 개
데이터시트 보기 →LM358QDRQ1
⚡ 동일 패키지 ⚠️ 사양 미검증✓ 재고 있음
$0.18 / 개
데이터시트 보기 →OPA2172ID 최대 정격 & 전기적 특성
| 채널 수 | 2 |
| Supply Voltage Range | +4.5 V to +36 V (±2.25 V to ±18 V) |
| Gain Bandwidth Product | 10 MHz |
| Input Offset Voltage | ±0.2 mV |
| Offset Voltage Drift | ±0.3 uV/C |
| Input Bias Current | ±8 pA |
| 대기 전류 | 1.6 mA per amplifier |
| 노이즈 밀도 | 7 nV/√Hz |
| 출력 유형 | Rail-to-Rail Output |
| 동작 온도 | -40C to +125C |
| 패키지 | 8-SOIC (D) |
| 실장 유형 | Surface Mount |
| Amplifier Type | General Purpose / Precision |
| RoHS 상태 | Compliant |
OPA2172ID 핀 구성
| 핀 1 | OUT A — Output of amplifier A |
| 핀 2 | IN A- — Inverting input A |
| 핀 3 | IN A+ — Non-inverting input A |
| 핀 4 | V- — Negative supply (or GND in single supply) |
| 핀 5 | IN B+ — Non-inverting input B |
| 핀 6 | IN B- — Inverting input B |
| 핀 7 | OUT B — Output of amplifier B |
| 핀 8 | V+ — Positive supply |
일반적인 애플리케이션
OPA2172ID 적합 용도: 6 애플리케이션s: Motor Control Current Sensing, Solar Inverter Power Stages, Audio Signal Processing, Power Supply Feedback Loops, Industrial Process Control Sensing, Automotive Signal Conditioning.
Motor Control Current Sensing
The OPA2172 amplifies small current-sense signals in 24 V or 48 V motor drives, where its ±0.2 mV offset and ±0.3 uV/C drift preserve accuracy across temperature. The 10 MHz bandwidth supports fast feedback loops for torque control, while the 36 V supply range allows direct connection to industrial rail-derived supplies. Rail-to-rail output maximizes ADC input range, improving measurement resolution in FOC motor controllers paired with TI C2000 MCUs such as the TMS320F28034-Q1.
추천
Solar Inverter Power Stages
In solar inverters, the OPA2172 conditions voltage and current feedback signals for MPPT and grid-synchronization control. Its wide +4.5 V to +36 V supply range tolerates industrial supply variation, and 7 nV/√Hz noise keeps small-signal sensing clean in electrically noisy switching environments. The rail-to-rail output fully utilizes low-voltage ADC input ranges, and the low 1.6 mA per amplifier quiescent current reduces standby losses in energy-harvesting equipment where every milliwatt counts.
추천
Audio Signal Processing
The OPA2172 serves as a low-noise preamp, active filter, and DAC output buffer in professional and consumer audio. Its 7 nV/√Hz voltage noise and 10 MHz bandwidth preserve transient fidelity, and the high slew rate prevents slew-induced distortion on high-amplitude line-level signals. Audio synth designers commonly substitute it for the noisier TL072 (as noted in the O_C module community). Its rail-to-rail output maximizes headroom on single-supply audio rails without large coupling capacitors.
추천
Power Supply Feedback Loops
The OPA2172 implements error amplifiers and loop compensation in AC-DC and DC-DC power supplies. With a 36 V supply rating, it can monitor high-voltage rails directly through dividers, while the ±0.2 mV offset tightens output regulation accuracy. The 10 MHz bandwidth supports fast transient-response loops in designs using TI UCC and TPS controllers. Rail-to-rail output lets the error amp swing fully across the controller reference range for precise duty-cycle control.
추천
Industrial Process Control Sensing
In factory instrumentation, the OPA2172 amplifies signals from pressure, temperature, and pH sensors. The ±8 pA CMOS bias current suits high-impedance piezo and glass-electrode sources, and ±0.3 uV/C drift keeps calibration stable across -40C to +125C industrial ranges. The 4.5 V minimum supply works with 5 V logic rails, while the 36 V maximum tolerates 24 V industrial buses. Its dual channel allows a sense amplifier plus an active anti-aliasing filter in a single SOIC-8 footprint.
추천
Automotive Signal Conditioning
Using the AEC-Q100 qualified OPA2172-Q1 variant, this op amp conditions battery-voltage, current, and position-sensor signals in automotive ECUs. The 36 V rating covers load-dump and 12 V battery transients with margin, and the -40C to +125C temperature range meets underhood requirements. Low offset drift ensures long-term accuracy in safety-relevant monitoring. Pairs with TI automotive ADCs and isolated amplifiers for battery-management and traction-invertor sensing chains.
추천
추천 제품 요약
엔지니어링 참조 데이터: OPA2172ID — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA2172AID | OPA2171AID | OPA1688 | LM358QDRQ1 |
|---|---|---|---|---|---|
| Package | 8-SOIC (D) | 8-SOIC (D) - same | 8-SOIC (D) - same | 8-SOIC (D) - same | 8-SOIC (D) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Supply Voltage Max | 36 V | 36 V | 36 V | 24 V | 32 V |
| Gain Bandwidth | 10 MHz | 10 MHz | 3 MHz | 10 MHz | ~1 MHz |
| Offset Voltage | ±0.2 mV | ±0.2 mV (tighter A-grade limit) | ±0.025 mV | ±0.3 mV | ±3 mV |
| Noise Density | 7 nV/√Hz | 7 nV/√Hz | 18 nV/√Hz | 10.5 nV/√Hz | 40 nV/√Hz |
| Quiescent Current | 1.6 mA per amp | 1.6 mA per amp | 0.475 mA per amp | 0.5 mA per amp | 0.5 mA per amp |
| Output Type | Rail-to-Rail Output | RRO | RRO | RRO | Not RRO |
| Automotive Grade | No (Q1 variant available) | No | Q1 available | No | Yes (Q1) |
주요 차별점
- 36 V supply with 10 MHz bandwidth combination (vs LM358QDRQ1)
- Much lower offset than budget precision parts (vs LM358QDRQ1)
- Higher supply headroom than OPA1688 (vs OPA1688)
설계 노트
Place 0.1 uF ceramic decoupling capacitors directly across the V+ (pin 8) and V- (pin 4) pins with short, low-inductance returns. At 10 MHz bandwidth, long supply traces can resonate with parasitic inductance and cause peaking. A small (10-22 ohm) series resistor or ferrite bead in the supply line plus local capacitance improves noise isolation in mixed-signal boards.
For best noise performance in transimpedance and precision gain stages, keep feedback resistor values low; the OPA2172's 7 nV/√Hz noise is only realized when resistor thermal noise is below amplifier noise (e.g., use <10 kohm feedback in low-gain stages). The CMOS ±8 pA bias current permits large input resistors without DC error, but verify stability with input capacitance.
The rail-to-rail output swing degrades under heavy load - check output swing versus load curves in the TI OPAx172 datasheet when driving low-impedance loads near the rails. Do not exceed 36 V absolute maximum supply, and note input common-mode range does not include the positive rail, so non-inverting gain configurations must keep input voltages below approximately (V+) - 2 V.
규정 준수 정보
RoHS compliant per TI product page. AEC-Q100 grade available via OPA2172-Q1 variant.
